Commit b1f625e0d8 extended
ap_scan_as_station to be able to distinguish between AP and P2P GO
iftypes. However, it did this in a way that completely lost the original
mode because drv->nlmode had already been replaced with the station
mode. Fix this by storing the correct old mode.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
If the peer device has already acknowledge receipt of the Invitation
Request frame, it is better not to re-start invitation by sending
another Invitation Request. This should not be needed since the peer
already has received the Invitation Request frame and sending the second
round in this type of sequence can cause issues with nl80211 offloaded
offchannel TX operations since driver_nl80211.c will lose the cookie
value for the first pending Action frame and may not be able to cancel
offchannel wait for it properly. this has been seen to trigger a failure
in the p2p_go_invite_auth test case with the scan failing due to GO
sending out Probe Response frame on incorrect channel (the channel used
in that not-cancelled Action TX).
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Commit bd3a373767 added a mechanism to use
AP Channel attribute from within a Credential attribute to optimize
scans. However, this design is not actually used with the WPS NFC use
cases. With configuration token, the AP Channel attribute is in the same
container with the Credential attribute (and that was also handled in
the previous implementation). With connection handover, AP Channel
information is outside the Credential attribute as well.
Simplify implementation by removing the AP Channel within Credential
case. This allows wpas_wps_use_cred() to get the AP Channel from the
container instead of having to find this during credential iteration.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This is not really used in practice and there is no need to maintain
unsed code that would only print debug log entries.
Signed-hostap: Jouni Malinen <j@w1.fi>
Commit 795baf773f ('hostapd: Filter
channel list updated events after country code change') uses the
EVENT_CHANNEL_LIST_CHANGED data pointer, but it updated only one of the
callers to provide that data. NL80211_CMD_REG_BEACON_HINT event was
still sending the event without the initiator data and resulted in NULL
pointer dereference, e.g., if a scan was run while hostapd was running
and the driver was in world roaming state and enabled a channel for
active scans.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The hostapd compilation displays a below warning On NetBSD 6.1.2.
../src/drivers/driver_bsd.c:72:1: warning: 'get80211opmode' defined but not used
This patch solves it and moves other functions to appropriate position to
reduce #ifdef.
Signed-hostap: Masashi Honma <masashi.honma@gmail.com>
Before this patch, 1 second timeout was used for regulatory updates. In
some cases, specially when we reload driver modules on some slower
platforms this could take more than 1 second (about 2 seconds). This is
important specially for DFS case, where we have to have correct DFS
region before we will start CAC. In other case (unknown DFS region), CAC
will fail. 5 seconds should be enough for all cases.
Signed-hostap: Janusz Dziedzic <janusz.dziedzic@tieto.com>
The original RSSI filter semantics for scheduled scan were
really confusing - a separate matchset was created, but it
wasn't actually treated as a separate matchset in the kernel
but rather used as the global RSSI value. The RSSI matchset
thus behaved like an RSSI filter outside of the matchsets,
being ANDed rather than ORed (as normal between matchsets.)
To make this less confusing, I changed the kernel API a bit
to actually treat the RSSI inside each matchset properly,
but keeping it compatible with the old approach by using a
matchset with only an RSSI value as the default for all the
other matchsets, and adding it as a separate matchset only
if it's the only one.
The proper way for wpa_supplicant to do this then would be
to add the RSSI to each SSID matchset, and only add another
matchset without SSID if there's none with.
However, to keep compatibility with older kernels, always
keep the non-SSID matchset and only add the RSSI to all the
other matchsets. This gets close to the desired behaviour,
the only difference would be that we shouldn't add the RSSI
matchset if there are others, but stays compatible with old
and new kernels, as new ones ignore the RSSI-only matchset
if there are others and those others have an RSSI.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
1. In wpa_config_process_bgscan() fix memory leak after
calling wpa_config_parse_string()
2. In hostapd_config_defaults(), on failure to allocate bss->radius,
conf->bss was not freed.
3. In p2p_deauth_nofif(), memory allocated in p2p_parse_ies() was not
freed in case of NULL minor_reason_code.
4. In p2p_disassoc_nofif(), memory allocated in p2p_parse_ies() was
not freed in case of NULL minor_reason_code.
5. In p2p_process_go_neg_conf(), memory allocated was not freed in
case that the P2P Device interface was not waiting for a
GO Negotiation Confirm.
6. In wpa_set_pkcs11_engine_and_module_path(), the wrong pointer was
checked.
Signed-hostap: Eytan Lifshitz <eytan.lifshitz@intel.com>
It is possible for channel switch notification to be missing channel
type attribute. This is true at least for VHT80. This led to
iface->conf->secondary_channel being set to 0. This in turn made
subsequent DFS-triggered CSA to fail due to invalid frequency
parameters.
Signed-hostap: Michal Kazior <michal.kazior@tieto.com>
This checks if the NL80211_ATTR_IFINDEX attribute is present before
trying to get the value of interface index.
Signed-hostap: Shital Jaju <shitalj@broadcom.com>
If CONFIG_WPS_TESTING=y is enabled in build configuration, the new
wps_corrupt_pkhash parameter (similar to wps_testing_dummy_cred) can be
used to request public key hash to be corrupted in all generated OOB
Device Password attributes. This can be used for testing purposes to
validate public key hash validation steps.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This adds a new P2P Invitation mechanism to invite a P2P Device with an
NFC Tag to an already operating group when the GO with NFC Device reads
the NFC Tag. The P2P Device with the NFC Tag will then accept invitation
and connect to the group automatically using its OOB Device Password.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
When "P2P_SET nfc_tag 1" is used to enable the own NFC Tag for P2P, also
enable it for any running GO interface.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
P2P Group ID can optionally be included in the connection handover
messages when acting as a P2P Client in a group. Add this information
and show it in the P2P-NFC-PEER-CLIENT event message.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
When the NFC connection handover message received from a peer indicates
that the peer is operating as a GO on a specific channel, use that
information to avoid having to go through full scan. In addition, skip
the separate join-a-group scan since we already know the operating
channel, GO P2P Device Address, and SSID.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This was already done for Registrar, but the Enrollee case did not
set config error properly if Registrar public key did not match the
hash received during NFC connection handover.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Instead of automatically triggering a connection, provide an indication
of one of the devices being a P2P client to upper layers to allow user
to determine what to do next.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Send a P2P-NFC-BOTH-GO event to upper layers to determine what to
do in case both devices going through NFC connection handover are
already operating as a GO.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This new mechanism allows P2P Client to request an IPv4 address from the
GO as part of the 4-way handshake to avoid use of DHCP exchange after
4-way handshake. If the new mechanism is used, the assigned IP address
is shown in the P2P-GROUP-STARTED event on the client side with
following new parameters: ip_addr, ip_mask, go_ip_addr. The assigned IP
address is included in the AP-STA-CONNECTED event on the GO side as a
new ip_addr parameter. The IP address is valid for the duration of the
association.
The IP address pool for this new mechanism is configured as global
wpa_supplicant configuration file parameters ip_addr_go, ip_addr_mask,
ip_addr_star, ip_addr_end. For example:
ip_addr_go=192.168.42.1
ip_addr_mask=255.255.255.0
ip_addr_start=192.168.42.2
ip_addr_end=192.168.42.100
DHCP mechanism is expected to be enabled at the same time to support P2P
Devices that do not use the new mechanism. The easiest way of managing
the IP addresses is by splitting the IP address range into two parts and
assign a separate range for wpa_supplicant and DHCP server.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
When NFC connection handover is used to trigger GO Negotiation, the
channel used for the GO Negotiation frames is already known. As such,
there is no need to use the Listen operations to find the peer.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The device with the NFC Tag can be configured to enable NFC to be used
with "P2P_SET nfc_tag 1" and "P2P_LISTEN" commands to allow static
handover to be used.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
"NFC_REPORT_HANDOVER {INIT,RESP} P2P <req> <sel>" can now be used to
report completed NFC negotiated connection handover in which the P2P
alternative carrier was selected.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
"NFC_GET_HANDOVER_{REQ,SEL} NDEF P2P-CR" can now be used to build P2P
alternative carrier record for NFC connection handover request/select
messages.
Static connection handover case can be enabled by configuring the DH
parameters (either with wps_nfc_* configuration parameters or with
WPS_NFC_TOKEN command at run time. The NFC Tag contents can be generated
with "NFC_GET_HANDOVER_SEL NDEF P2P-CR-TAG" after having configured
Listen channel (p2p_listen_reg_class/p2p_listen_channel).
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
GO Negotiation needs to know which OOB Device Password ID is assigned
for the peer when NFC is used as the trigger.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
These functions can be used to build the WPS attributes for P2P NFC
connection handover messages.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The new WPS connection handover select includes Registrar public key
hash instead of credential. Use the new information to start
abbreviated WPS handshake instead of configuring a new network directly
from the old Credential-from-NFC design.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The contents of the WPS connection handover select message was modified
to include the Registrar public key hash instead of the credential.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The new NFC connection handover design requires the AP/Registrar to
process the connection handover request message received from the
Enrollee. Add control interface commands for handling this.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
It is more useful to be able to build a single NFC carrier record
instead of the full connection handover request message to allow
external components to decide whether to negotiate which alternative
carrier is used. This updates the carrier record contents to the new
design to include Enrollee public key hash and provides this as a
carrier record instead of full message. An external program is expected
to be used to build the full NFC connection handover message with
potentially other alternative carrier records included.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This allows DH key generation to be shared for other purposes than just
the case of OOB Device Password building. In addition, force the DH
public key buffer to be full 192 octets with zero padding to avoid
issues with the buffer being used in messages sent to a peer device.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The new Device Password ID 7 is used to indicate that NFC connection
handover is used with DH public key hash from both devices being
exchanged over the NFC connection handover messages. This allows an
abbreviated M1-M2 handshake to be used since Device Password does not
need to be used when DH is authenticated with the out-of-band
information (validation of the public key against the hash).
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
When both the Registrar and Enrollee public key hashes are delivered
out-of-band (in NFC connection handover), use abbreviated WPS handshake
(skip M3-M8).
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Since the Enrollee can now get the public key hash from the Registrar,
there is need to validate this during the WPS protocol run.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Instead of terminating the WPS protocol immediately, go through an M2D
exchange to notify Enrollee of the public key hash mismatch.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This old Version attribute is not really needed anymore for these use
cases with the assumption that there are no existing WPS+NFC
deployments. It was removed from the WSC specification, so make the
implementation match that change.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Provide local GO channel to the P2P module so that it can be used in
messages that indicate the current operating channel.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This functionality is needed for other messages, too, so split the group
info building code into a separate helper function.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This adds a QCA vendor specific nl80211 event to allow the driver to
indicate a list of frequency ranges that should be avoided due to
interference or possible known co-existance constraints. Such
frequencies are marked as not allowed for P2P use to force groups to be
formed on different channels.
If a P2P GO is operating on a channel that the driver recommended not to
use, a notification about this is sent on the control interface and
upper layer code may decide to tear down the group and optionally
restart it on another channel. As a TODO item, this could also be changed
to use CSA to avoid removing the group.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This file is used as a registry of identifier assignments from the
Qualcomm Atheros OUI 00:13:74 for purposes other than MAC address
assignment. One of the first uses will be for nl80211 vendor
commands/events which is reason for the preparation change in
driver_nl80211.c
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
When GAS is used with PMF negotiated, Protected Dual of Public Action
frames are expected to be used instead of Public Action frames, i.e.,
the GAS/ANQP frames are expected to be encrypted. Conver Public Action
GAS queries to use Dual of Public Action frame if PMF has been
negotiated with the AP to which the frame is being sent.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
When GAS is used with PMF negotiated, Protected Dual of Public Action
frames are expected to be used instead of Public Action frames, i.e.,
the GAS/ANQP frames are expected to be encrypted. Add support for this
different category of Action frames being used for GAS. The payload
after the Category field is identical, so the only change is in using
the Category field based on what was received in the request frames. For
backwards compatibility, do not enforce protected dual to be used on the
AP side, i.e., follow what the station does.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Due to misplaced parenthesis, unprotected not-Robust Action frames
(e.g., Public Action frames) were dropped in handle_assoc() when such
frames were received during an association that had negotiated use of
PMF. This is not correct since only unprotected Robust Action frames
were supposed to be handled in this way.
This would have broken any Public Action frame use during PMF
association, but such frames were not really supposed to be used
currently (ANQP as the only possible use case should really use
protected dual option in such case).
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Fix sizeof in a validity comparison of nl80211_vendor_cmd_info size. The
incorrect version happened to work on 64-bit builds due the structure
being eight octets, but this was incorrect and would not used with
32-bit builds.
Signed-hostap: Max Stepanov <Max.Stepanov@intel.com>
While iterating over the stations hostapd_ctrl_iface_sta_mib()
might be called with sta == NULL. Fix this.
Signed-hostap: Ilan Peer <ilan.peer@intel.com>
The new default value (from 300 to 60 seconds) makes the internal P2P
peer list somewhat faster to react to peers becoming unreachable while
still maintaining entries for some time to avoid them disappearing
during user interaction (e.g., selecting a peer for a connection or
entering a PIN).
Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
A P2P Device while in the Listen state waiting to respond for the
obtained group negotiation request shall give a fair chance for other
concurrent sessions to use the shared radio by inducing an idle time
between the successive listen states. However, if there are no
concurrent operations, this idle time can be reduced.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Previously, GO Negotiation Request frame was used to update a peer entry
if only a Probe Request from that peer had been received. However, it
would be possible, even if unlikely, for a peer to be discovered based
on receiving Provision Discovery Request frame from it and no Probe
Request frame. In such a case, the Listen frequency of the peer would
not be known and group formation could not be (re-)initialized with that
peer. Fix this by allowing the GO Negotiation Request frame to update
peer entry if the current peer entry does not include Listen or
Operating frequency.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This adds one more case of active P2P peer detection so that
p2p_expire_peers() cannot hit a case where a GO Negotiation peer would
be removed.
Signed-hostap: Jithu Jance <jithu@broadcom.com>
The information of the peer's supported channel and operating class
is required for the driver to do TDLS off channel operations with a
compatible peer. Pass this information to the driver when the peer
station is getting added.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Some EAP methods can go through a step that is expected to fail and as
such, should not trigger temporary network disabling when processing
EAP-Failure or deauthentication. EAP-WSC for WPS was already handled as
a special case, but similar behavior is needed for EAP-FAST with
unauthenticated provisioning.
Signed-hostap: Jouni Malinen <j@w1.fi>
EAP-FAST requires pac_file to be configured, so make it clearer from the
debug output if missing configuration parameter was the reason for
EAP-FAST initialization failing.
Signed-hostap: Jouni Malinen <j@w1.fi>
The hash return buffer was previously left uninitialized in case
externally stored password ("password=ext:...") was used. This could
result in MSCHAPv2 failure if that uninitialized memory happened to be
something else than zero.
Signed-hostap: Jouni Malinen <j@w1.fi>
It is possible for the configuration to be temporarily invalid when
adding a new AP through SET commands followed by ENABLE. Avoid this
issue by using less strict validation on SET commands and perform full
configuration validation only on ENABLE. Use cases with configuration
file maintain their previous behavior, i.e., full validation after the
file has been read.
Signed-hostap: Jouni Malinen <j@w1.fi>
This reverts commit 792c8877c3
('P2P: Send GO Negotiation Confirm without wait').
Some drivers rely on the wait period for sending packets on the
off-channel. If the wait value is small, there's a race condition where
the driver ROC might complete before the packet was sent out. This
doesn't impede other drivers, as the wait is cancelled when a
Tx-completion arrives from the remote peer.
Signed-hostap: Arik Nemtsov <arik@wizery.com>
The missing call to scan_action_done() may keep us off-channel for 250
ms following sending GO Negotiation Response. In case the operating
channel is different from this channel and we're GO, a race could lead
to start beaconing while off-channel. This could potentially cause the
Beacon frames to go out on incorrect channel with some drivers.
Signed-hostap: Eyal Shapira <eyal@wizery.com>
The error path in bsd_init() on struct bsd_driver_data allocation was
jumping to location where drv is dereferenced. That will crash and it is
easier to just return from the function since no cleanup steps are
needed in this case.
Signed-hostap: Jouni Malinen <j@w1.fi>
Currently these three steps runs for each event.
1. get buffer size via system
2. allocate a memory for event
3. free the memory
The wpa_supplicant receives 4 events from boot to be connected.
So this patch prepare the event buffer at the init process.
I have tested wpa_supplicant on NetBSD 6.1.2.
But I could not tested hostapd because I do not have AP enabled device.
Signed-hostap: Masashi Honma <masashi.honma@gmail.com>
Replace channel_switch_supported flag of the
wpa_driver_nl80211_data by WPA_DRIVER_FLAGS_AP_CSA inside
wpa_driver_capa.flags. It makes more sense and also can
be accessed by wpa_supplicant.
Signed-hostap: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
This is just like the same command in wpa_supplicant, i.e., "hostapd_cli
status driver" can be used to fetch information about the driver status
and capabilities.
Signed-hostap: Jouni Malinen <j@w1.fi>
PEAPv2 implementation was not fully completed and there does not seem to
be any deployments of PEAPv2 nor any clear sign of such showing up in
the future either. As such, there is not much point in maintaining this
implementation in hostapd/wpa_supplicant.
Signed-hostap: Jouni Malinen <j@w1.fi>
The standard fragment_size network parameter can now be used to
configure EAP-pwd fragmentation limit instead of always using the
hardcoded value of 1020.
Signed-hostap: Jouni Malinen <j@w1.fi>
The standard fragment_size network parameter can now be used to
configure EAP-IKEv2 fragmentation limit instead of always using the
hardcoded value of 1400.
Signed-hostap: Jouni Malinen <j@w1.fi>
Setting methodState = DONE for the case where GPSK-1 is found to be
invalid or incompatible allows EAP state machine to proceed to FAILURE
state instead of remaining stuck until AP times out the connection.
Signed-hostap: Jouni Malinen <j@w1.fi>
phase1 parameter 'cipher' can now be used to specify which algorithm
proposal is selected, e.g., with phase1="cipher=1" selecting AES-based
design and cipher=2 SHA256-based. This is mainly for testing purposes,
but can also be used to enforce stronger algorithms to be used.
Signed-hostap: Jouni Malinen <j@w1.fi>
One of the RFC 4137 state transitions (METHOD -> FAILURE) had been
forgotten and this could result in EAP peer method processing not
reporting failure immediately and instead, remain stuck waiting for the
connection to time out. Fix this by adding the methodState == DONE &&
decision == FAIL case to allow immediate reporting of failures.
The condition from RFC 4137 as-is would cause problems for number of the
existing EAP method implementations since they use that in places where
the final message before EAP-Failure should really be sent to the EAP
server (e.g., WSC_Done in EAP-WSC). Address this by includng eapRespData
== NULL as an additional constraint for entering FAILURE state directly
from METHOD.
Signed-hostap: Jouni Malinen <j@w1.fi>
Commit e2f5a9889a was supposed to prevent
new scan request from pushing out the old one. However, it did not
really do that since eloop_deplete_timeout() returned 0 both for the
case where the old timeout existed (and was sooner) and if the old
timeout did not exist. It returned 1 only for the case where an old
timeout did exist and was larger than the new requested value. That case
used to result in wpa_supplicant_req_scan() rescheduling the timeout,
but hew code in eloop_deplete_timeout() did the exact same thing and as
such, did not really change anything apart from the debug log message.
Extend the eloop_deplete_timeout() (and eloop_replenish_timeout() for
that matter since it is very similar) to return three different values
based on whether the timeout existed or not and if yes, whether it was
modified. This allows wpa_supplicant_req_scan() to schedule a new
timeout only in the case there was no old timeout.
Signed-hostap: Jouni Malinen <j@w1.fi>
The new control interface command RADIO_WORK can be used by external
programs to request radio allocation slots from wpa_supplicant if
exclusive radio control is needed, e.g., for offchannel operations. If
such operations are done directly to the driver, wpa_supplicant may not
have enough information to avoid conflicting operations. This new
command can be used to provide enough information and radio scheduling
to avoid issues with such cases.
Signed-hostap: Jouni Malinen <j@w1.fi>
Avoid concurrent P2P scan requests with any other exclusive use of the
radio by using the radio work queuing mechanism. This removes some of
the earlier workarounds that postponed scans depending on other
operations.
Signed-hostap: Jouni Malinen <j@w1.fi>
If the port status did not change or would not need to get an update
after portEnabled changes, there is no need to try to set the driver to
use the same value it is already using based on the previous state.
Remove such calls to reduce number of operations during reassociation.
In addition, this cleans up the debug log by removing unnecessary
duplicated entries.
Signed-hostap: Jouni Malinen <j@w1.fi>
If the BSS table within wpa_supplicant is flushed, request the driver to
flush its own scan result table during the next scan. This can avoid
unexpected old BSS entries showing up after BSS_FLUSH or FLUSH command
in cases where the driver may maintain its internal cache of scan
results (e.g., cfg80211 BSS table persists at least for 15 seconds).
In addition to doing this automatically on BSS_FLUSH/FLUSH, a new SCAN
command argument, only_new=1, can be used to request a manual scan
request to do same. Though, it should be noted that this maintains the
BSS table within wpa_supplicant. BSS_FLUSH followed by SCAN command can
be used to clear all BSS entries from both the driver and
wpa_supplicant.
Signed-hostap: Jouni Malinen <j@w1.fi>
This debugging mechanism has now been deprecated by the control
interface commands that can be used to fetch same internal information
from hostapd in a more convenient way. Leave the empty USR1 signal
handler and configuration file parameter for backwards compatibility.
They can be removed in future versions of hostapd.
Signed-hostap: Jouni Malinen <j@w1.fi>
The per-STA/Supplicant state information from the EAPOL authenticator
is now available through "STA <MAC Address> eapol" command.
Signed-hostap: Jouni Malinen <j@w1.fi>
This adds TX/RX statistics and information about association into the
per-STA data that is available through the hostapd control interface. In
addition, information about the EAP method is now included with the IEEE
802.1X data.
Signed-hostap: Jouni Malinen <j@w1.fi>
These old driver wrappers have been removed quite some time ago, but
some of the build configuration notes were still describing how they
are configured.
Signed-hostap: Jouni Malinen <j@w1.fi>
Print into the debug log the list of vendor commands and events that the
driver supports. In addition, add a generic handler for vendor events.
This can be extended for each vendor/subcmd.
Signed-hostap: Jouni Malinen <j@w1.fi>
The P2P_PRESENCE_REQ command did not give any easily available
indication of the response received from the GO. Make this more useful
by providing such response (if received) as a ctrl_iface monitor event
(P2P-PRESENCE-RESPONSE).
Signed-hostap: Jouni Malinen <j@w1.fi>
intval is marked le16 and should be used through proper byte order
conversion functions even if it ended up getting set correctly due to
the two operations cancelling each other.
Signed-hostap: Jouni Malinen <j@w1.fi>
These were somewhat more hidden to avoid direct use, but there are now
numerous places where these are needed and more justification to make
the extern int declarations available from wpa_debug.h. In addition,
this avoids some warnings from sparse.
Signed-hostap: Jouni Malinen <j@w1.fi>
use_monitor=1 and force_connect_cmd=1 driver parameters can now be used
to force older monitor interface design and the connect API (SME in
driver) to increase hwsim testing coverage.
Signed-hostap: Jouni Malinen <j@w1.fi>
If Action frame registration in nl80211_mgmt_subscribe_non_ap() failed
for any frame type, the previous implementation skipped
nl80211_mgmt_handle_register_eloop() call. This is not desirable since
none of the Action frame types could be received and even worse, the
following nl80211_destroy_eloop_handle() call for nl_mgmt would likely
result in crashing the process due to the ELOOP_SOCKET_INVALID XOR
operation. This could be triggered at least in a P2P group interface
startup failure case.
Signed-hostap: Jouni Malinen <j@w1.fi>
Previously, it was possible for bss_info_handler() to end up dropping a
newer scan result entry if there were two entries with the same BSSID
and SSID (i.e., only frequency was different) and we were not associated
with either. This could happen, e.g., in some P2P use cases where device
discovery may happen on different channels. Fix this by checking the age
of the scan entries as well to prefer the most recent response.
Signed-hostap: Jouni Malinen <j@w1.fi>
Most of the attributes to these commands are identical and there is no
need to maintain two copies of the same functionality.
Signed-hostap: Jouni Malinen <j@w1.fi>
WPA_CIPHER_* and CIPHER_* are used for the exact same set of cipher
suites with the main difference being that the WPA_CIPHER_* version is
suitable to be used as a bitfield. Similarly, WPA_KEY_MGMT_* and
KEY_MGMT_* have similar design for AKMs. There is no need to maintain
two separate copies of the definitions since the bitfield compatible
version can be used for both needs. Get rid of the CIPHER_* and
KEY_MGMT_* versions to clean up the implementation by getting rid of
unnecessary mapping functions.
Signed-hostap: Jouni Malinen <j@w1.fi>
NL80211_ATTR_CONTROL_PORT was previously set only for
NL80211_CMD_ASSOCIATE, but it should also be set when using
NL80211_CMD_COMMAND (driver-based SME) even though none of the current
non-mac80211 drivers use this.
Signed-hostap: Jouni Malinen <j@w1.fi>
The option of handling upper layer P2P management operations within the
driver/firmware was originally planned to be used with wpa_supplicant,
but this has not really happened and there is no clear sign of this
being needed in the near term either. This functionality has not been
completed and it is certainly not being kept up-to-date or tested. As
such, it is best to remove it for now and if this or something similar
is needed in the future, it can be brought back once a clear need for it
has been demonstrated first.
Signed-hostap: Jouni Malinen <j@w1.fi>
prime_len was added to the start pointer twice and because of this, the
actual y coordinate was not verified to be valid. This could also result
in reading beyond the buffer in some cases.
Signed-hostap: Jouni Malinen <j@w1.fi>
phase1 parameters dhgroup, encr, prf, and mac can now be used to specify
which algorithm proposal is selected, e.g., with phase1="dhgroup=3
encr=1 prf=1 mac=1" selecting the mandatory-to-implement case. This is
mainly for testing purposes, but can also be used to enforce stronger
algorithms to be used.
Signed-hostap: Jouni Malinen <j@w1.fi>
These information elements are not really used anywhere in hostapd or
wpa_supplicant nor is there any plan to use them. As such, there is no
need to keep the code here either, so save couple of bytes here.
Signed-hostap: Jouni Malinen <j@w1.fi>
This driver event was used separately for some Action frames, but all
the driver wrappers converted to this from information that would have
been enough to indicate an EVENT_RX_MGMT event. In addition, the
received event was then converted back to a full IEEE 802.11 management
frame for processing in most cases. This is unnecessary complexity, so
get rid of the extra path and use EVENT_RX_MGMT for Action frames as
well as other management frame subtypes.
Signed-hostap: Jouni Malinen <j@w1.fi>
This can be used to silence compiler warnings in cases where #ifdef
blocks can leave some variables or functions unused and there is no
cleaner way of avoiding the warnings.
Signed-hostap: Jouni Malinen <j@w1.fi>
Commit 88b32a99d3 added support for using
some Action frame processing in hostapd for drivers that handle most of
SME/MLME internally (it added FT, this has since be extended for SA
Query and WNM). However, this was added in a way that ended up getting
both the hostapd_rx_action() and hostapd_action_rx() called for Action
frames. This could result in an attempt to process FT, SA Query, and WNM
Action frames twice.
There is need for more significant cleanup in Action frame processing in
hostapd depending on the driver type, but as a simple step to avoid
issues, skip the hostapd_action_rx() call if hostapd_rx_action()
processed the frame.
Signed-hostap: Jouni Malinen <j@w1.fi>
Even though this is a short timeout, it is at least theoretically
possible for the interface to be removed while waiting for
reconfiguration to start. Avoid issues with this by cancelling the
timeout on any WPS interface deinit. In theory, this should be postponed
until interface removal, but that does not fit very nicely to the
current wps_hostapd.c style.
Signed-hostap: Jouni Malinen <j@w1.fi>
Previously, wps_version_number was used only to test extensibility to
newer version numbers, but it can also be used to enable testing of
older versions (1.0), e.g., to avoid hitting some 2.0 specific
validation steps.
Signed-hostap: Jouni Malinen <j@w1.fi>
It is fine to try to cancel a registration that does not exist, so there
is no need to have the duplicated checks for eloop timeout and socket
registration.
Signed-hostap: Jouni Malinen <j@w1.fi>
It was already possible to configure hostapd and wpa_supplicant to use
FT-SAE for the key management, but number of places were missing proper
AKM checks to allow FT to be used with the new AKM.
Signed-hostap: Jouni Malinen <j@w1.fi>
Action frame RX report through EVENT_RX_ACTION did not indicate whether
the frame was protected or not even though that information is available
in mlme_event_mgmt(). hostapd_rx_action() has a workaround for setting
the protected flag for SA Query frames, but that did not apply for other
frames, like FT Action. This broke FT-over-DS when PMF is enabled with
newer kernel versions (i.e., the ones that do not use monitor interface
for receiving management frames).
Signed-hostap: Jouni Malinen <j@w1.fi>
The earlier changes to buffer EAPOL frames when not associated to avoid
race conditions (especially commit
3ab35a6603 but maybe something even before
that) broke PeerKey 4-way handshake. Fix this by using a separate check
before the race condition workaround to process PeerKey 4-way handshake
EAPOL-Key messages differently.
Signed-hostap: Jouni Malinen <j@w1.fi>
PeerKey entries need to be removed on disassociation and this needs to
be done in a way that cancels the possibly pending eloop timeout.
Signed-hostap: Jouni Malinen <j@w1.fi>
This is not really needed for anything and the standard does not require
such validation step to be made for Authentication frame transmission.
Signed-hostap: Jouni Malinen <j@w1.fi>
This can be useful for displaying the current STA state and also for
determining whether some operations are likely to fail or need
additional delay.
Signed-hostap: Jouni Malinen <j@w1.fi>
hostapd_drv_wnm_oper() needs to indicate an error if the driver callback
function is not implemented. Without this, the buf_len argument could
have been left uninitialized which could result in crashing the process.
Signed-hostap: Jouni Malinen <j@w1.fi>
This makes it easier to trigger the ESS Disassociation Imminent
operation from different sources.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This adds first steps at processing a BSS Transition Management Query on
the AP side. Mainly, the message is parsed and printed out in the debug
log and a minimal BSS Transition Management Request frame is sent as a
response. BSS Transition Management Response frame is also parsed and
details printed out in the debug log.
Signed-hostap: Jouni Malinen <j@w1.fi>
The previous version could end up calling WPA authenticator routines
even though the authenticator had not been initialized and this could
result in NULL pointer dereference.
Signed-hostap: Jouni Malinen <j@w1.fi>
This prepares wpa_supplicant for accepting cases where the AP does not
use group addressed frames.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
If the extended key usage of the AAA server certificate indicates
that the certificate is for client use, reject the TLS handshake.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
OCSP response may not include all the needed CA certificates, so use the
ones received during TLS handshake.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The five second timeout to call wps_er_deinit_finish() could potentially
be left behind when removing the ER data based on some other event. This
could result in double-freeing of wps_er context killing the process,
e.g., if the WPS ER functionality is stopped while in the process of
unsubscribing from an AP and then restarted.
In addition, AP entries could still be present in the
er->ap_unsubscribing list when the deinit timeout hits. These entries
would still maintain HTTP context pointing to the ER which would be
freed here and as such, the following HTTP client callback could refer
to freed memory and kill the process. Fix this by freeing AP entries
from ap_unsubscribing list when ER is deinitialized from timeout even if
such AP entries have not completed unsubscription from UPnP events.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Reduce race condition of the station trying to reconnect immediately
after AP reconfiguration through WPS by rescheduling the reload
timeout to happen after EAP completion rather than the originally
scheduled 100 ms after new configuration became known.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This enables more convenient protocol testing of station side
functionality in various error cases and unexpected sequences without
having to implement each test scenario within hostapd.
ext_mgmt_frame_handle parameter can be set to 1 to move all management
frame processing into an external program through control interface
events (MGMT-RX and MGMT-TX-STATUS) and command (MGMT_TX).
Signed-hostap: Jouni Malinen <j@w1.fi>
These files have been distributed only under the BSD license option
since February 2012. Clarify the license statements in the files to
match that to avoid confusion.
Signed-hostap: Jouni Malinen <j@w1.fi>
If configuration of the group key to the driver fails, move the WPA
group into failed state and indication group setup error to avoid cases
where AP could look like it is working even through the keys are not set
correctly.
Signed-hostap: Jouni Malinen <j@w1.fi>
This adds initial parts for supporting the new GCMP-256, CCMP-256,
BIP-GMAC-128, BIP-GMAC-256, and BIP-CMAC-256 cipher suites.
Signed-hostap: Jouni Malinen <j@w1.fi>
If secondary channel is provided for CSA, advertise it in the Secondary
Channel Offset element in Beacon and Probe Response frames.
Signed-hostap: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
When CSA flow starts, store the entire struct hostapd_freq_params and
not only CS frequency as it was before. The additional freq_params are
required to advertise CS supplementary IEs such as secondary channel,
wide bandwidth CS, etc.
Signed-hostap: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
This allows use of structs (and not only pointers) defined in drivers.h.
Remove also some not needed forward declarations and redundant includes.
Signed-hostap: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
The event debouncing isn't very accurate (since it doesn't
take sub-second resolution into account), but it should use
monotonic time anyway since it doesn't care about the wall
clock.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
The PBC ignore-start workaround just needs to check whether
the time is within 5 seconds, so should use monotonic time.
While at it, add a few more ifdefs to clearly separate the
code and variables needed.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
PBC sessions are just time-stamped when activated, and
eventually time out, so should use monotonic time.
While at it, make the code use os_reltime_expired().
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
The eloop already tracks the expiration/lifetime, and the expiration
isn't really used, so remove it. It should otherwise have used monotonic
time, but since it's not actually used, we can remove it instead.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
The RADIUS server needs to calculate uptime, which is relative
and thus should use monotonic time.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
Since the RADIUS client cares about relative time (retry timeout)
only, it should use monotonic time.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
The BSS table, scan timeout, and related functionality should use
monotonic time since they care about relative values (age) only.
Unfortunately, these are all connected, so the patch can't be split
further. Another problem with this is that it changes the driver wrapper
API. Though, it seems only the test driver is using this.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
This should probably have used monotonic time for entry timestamps, but
as those aren't used at all right now, so just remove them entirely.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The request retry loop only retries for 5 seconds, so any time
jumps would probably not affect it much, but it should be using
monotonic time nonetheless since it only cares about duration.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
Wall time jumps shouldn't affect MMIC failure/TKIP countermeasures,
so use monotonic time. Change the michael_mic_failure variable to
struct os_reltime for type-safety.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
Since the PMKSA cache only uses relative time, use the monotonic time
functions instead of wall time to be correct when the clock jumps.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
For type-safety, make sta->acct_session_start a struct os_reltime
and then use monotonic time for accounting. For RADIUS reporting,
continue to use wall clock time as specified by RFC 2869, but for
the session time use monotonic time.
Interestingly, RFC 2869 doesn't specify a timezone, so the value
is somewhat arbitrary.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
Do not assume the driver supports QoS Mapping, but instead, advertise
support for this only if CONFIG_INTERWORKING is defined and driver
indicates support for configuring QoS Map.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The driver_nl80211.c changes are needed to avoid compiler warnings
with two frequency attributes pointing to the same value.
Signed-hostap: Jouni Malinen <j@w1.fi>
If more BSSes are added in config file than are supported by the driver,
segmentation fault can appear. For this case, the interface_added flag
needs to be cleared if adding a new BSS fails.
Signed-hostap: Marek Kwaczynski <marek.kwaczynski@tieto.com>
Until now DFS was simply restarting the AP when radar was detected. Now
CSA is used to perform smooth switch to the new channel. Stations not
supporting CSA will behave as before.
Signed-hostap: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-hostap: Michal Kazior <michal.kazior@tieto.com>
This is needed for AP CSA. Since CSA must happen immediately after radar
is detected there's no time to perform CAC. Thus, radar channels must be
disabled when looking for a new channel to escape to after a radar is
detected.
Signed-hostap: Michal Kazior <michal.kazior@tieto.com>
Adds support for VHT by parsing bandwidth and center_freq{1,2}.
Signed-hostap: Michal Kazior <michal.kazior@tieto.com>
Signed-hostap: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Just the usual, with a new function os_reltime_initialized()
thrown in that checks whether time has ever been retrieved
(time can't be completely zero).
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
This helper functions checks whether a given entry has expired,
given the last active timestamp, the current time, and a timeout.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Based on priority, remove the connection with least priority whenever
a frequency conflict is detected.
Signed-hostap: Jithu Jance <jithu@broadcom.com>
Allow another EAP method to be tried if one of the enabled methods
fails. If all the remaining methods fail, reject connection by adding a
new METHOD_REQUEST -> FAILURE transition. Previously, this case resulted
in the state machine trying to send a message when none was available
and then waiting for a following event until timeout.
Signed-hostap: Jouni Malinen <j@w1.fi>
It is possible for the authentication server to be configured with a
PKCS #12 file that includes a private key, a server certificate, and a
CA certificate. This combination could result in server_cert and ca_cert
parameters not being present and that should still result in TLS context
getting initialized.
Signed-hostap: Jouni Malinen <j@w1.fi>
It was possible to configure hostapd in a way that could try to
initialize a TLS-based EAP method even when TLS library context was not
initialized (e.g., due to not configuring server or CA certificate).
Such a case could potentially result in NULL pointer dereference in the
TLS library, so check for this condition and reject EAP method
initialization.
Signed-hostap: Jouni Malinen <j@w1.fi>
Commit 390e489c0d extended hostapd BSS
interface removal capabilities. However, it ended up causing a
regression in wpa_supplicant P2P group interface handling. That P2P
group interface is removed through another driver_nl80211.c BSS context
and as such, the bss->added_if is not set. Fix this by verifying whether
the request is for another ifindex and if so, removing the interface
even if added_if is not marked.
Signed-hostap: Jouni Malinen <j@w1.fi>
Some non-mac80211 drivers, such as ath6kl, support STA inactivity timer
in firmware and may not provide connected stations' idle time to the
userspace. If the driver indicates support for offloaded operation, do
not start the inactivity timer in the hostapd.
Signed-hostap: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
struct beacon_data contains a lot of pointers. Make sure it gets cleared
to zero if hostapd_build_beacon_data() gets called from a path that does
not clear the structure first.
Signed-hostap: Janusz Dziedzic <janusz.dziedzic@tieto.com>
This is a mechanism used in Android to extend driver interface in vendor
specific ways. This is included only for the purpose of Android
compatibility. Proper interface commands should be used for any new
functionality.
Signed-hostap: Jouni Malinen <j@w1.fi>
Android uses a vendor specific library for implementing couple of driver
interface functions. Add the wrapper code to allow that mechanism to be
used.
Signed-hostap: Jouni Malinen <j@w1.fi>
Despite interface (and group) related sockets are not used
for control, they are created and may be left.
Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
Check if the BSS interface has started before setting beacon.
Lack of this condition can cause segmantation fault.
Signed-hostap: Marek Kwaczynski <marek.kwaczynski@tieto.com>
A reenable of the TDLS link while the host driver is already processing
the same (due to the retransmitted M2/M3 frames) might result in a
failed TDLS setup handshake due to some host driver's implementation.
Thus, issue enable link only when the peer's TDLS status signifies no
prior link (tpk_success=0).
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Commit de3cdf354a adding copying of the
STA's VHT capabilities into the STA entry on the AP. This was done in
allocated memory, but that new memory allocation was not freed anywhere.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Relative time shouldn't be calculated based on gettimeofday
because that clock can jump (e.g., when the time is adjusted
by the system administrator.)
On systems where that is available, use CLOCK_BOOTTIME (on
fairly recent Linux systems, this clock takes into account
the time spend suspended) or CLOCK_MONOTONIC (on Linux and
some POSIX systems, this clock is just freely running with
no adjustments.)
Reported-by: Holger Schurig <holgerschurig@gmail.com>
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
The 'started' state was tracked incorrectly. It also broke DFS
as it was using hostapd_enable/disable_iface() functions.
Signed-hostap: Michal Kazior <michal.kazior@tieto.com>
Some devices disable use of U-NII-1 (channels 36-48) for P2P due to it
being indoor use only in number of locations. If U-NII-3 (channels
149-161) is available, try to pick a channel from that range first
during random channel selection to reduce likelihood of interoperability
issues.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
If there are no other preferences from local configuration or driver,
prefer a random VHT channel instead of falling back to the fixed
pre-configured channel or 5 GHz/HT40 channel preference.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
If there are no other preferences from local configuration or driver,
prefer a random HT40 channel instead of falling back to the fixed
pre-configured channel or 5 GHz channel preference.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
If there are no other preferences from local configuration or driver,
prefer a random 5 GHz channel instead of falling back to the fixed
pre-configured channel (which is selected by default to be 1, 6, or 11).
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Use the new p2p_channel_select() function to select a VHT channel
at random when no other preferences are in effect.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Use the new p2p_channel_select() function to select an HT40 channel
at random when no other preferences are in effect.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The new p2p_channel_select() function can be re-used to implement
random channel selection from a set of operating classes in all
places that need such functonality.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This allows wlantest debug log output to be directed to a file so that
RELOG command can be used to rotate files more easily than stdout.
Signed-hostap: Jouni Malinen <j@w1.fi>
Add chan_switch to the control interface of wpa_supplicant and hostapd,
and also to wpa_cli and hostapd_cli.
Signed-hostap: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Build CSA settings and call the driver to perform the switch. Construct
Beacon, Probe Response, and (Re)Association Response frames both for CSA
period and for the new channel. These frames are built based on the
current configuration. Add CSA IE in Beacon and Probe Response frames.
Signed-hostap: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Add csa_settings struct which holds parameters for CSA. Change driver
interface for switch_channel(), so that it will receive this struct and
not only the new frequency as it was before. This allows wpa_supplicant
to provide all the required parameters (beacons, proberesp, assocresp,
CSA IE) which are required by cfg80211 implementation.
Signed-hostap: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
This was supposed to be a minimal sample of eloop wrapper, but it is
unclear whether this is of that much use and the file has not been kept
up-to-date. Remove this file to reduce maintenance effort. The other
eloop*.c files can be used as a starting point if something new is
needed.
Signed-hostap: Jouni Malinen <j@w1.fi>
Commit eb32460029 left an unneeded
sim_type argument to scard_init(). Remove that unnecessary argument to
clean up the implementation.
Signed-hostap: Masashi Honma <masashi.honma@gmail.com>
Add DBus methods for TDLS operations similar to those available
for the control interface. This includes Discover, Setup, and
Teardown commands. While here, add a method to query the TDLS
link status and add a DBus method for it.
Tested with CONFIG_TDLS enabled, on a TDLS-enabled host and
peer capable of TDLS:
dbus-send --system --dest=fi.w1.wpa_supplicant1 --print-reply \
/fi/w1/wpa_supplicant1/Interfaces/0 \
fi.w1.wpa_supplicant1.Interface.TDLSStatus string:<peer-mac-address>
yields: string "peer does not exist"
dbus-send --system --dest=fi.w1.wpa_supplicant1 --print-reply \
/fi/w1/wpa_supplicant1/Interfaces/0 \
fi.w1.wpa_supplicant1.Interface.TDLSDiscover string:<peer-mac-address>
yields no error
dbus-send --system --dest=fi.w1.wpa_supplicant1 --print-reply \
/fi/w1/wpa_supplicant1/Interfaces/0 \
fi.w1.wpa_supplicant1.Interface.TDLSSetup string:<peer-mac-address>
yields no error
dbus-send --system --dest=fi.w1.wpa_supplicant1 --print-reply \
/fi/w1/wpa_supplicant1/Interfaces/0 \
fi.w1.wpa_supplicant1.Interface.TDLSStatus string:<peer-mac-address>
yields: string "connected" after TDLS completes
dbus-send --system --dest=fi.w1.wpa_supplicant1 --print-reply \
/fi/w1/wpa_supplicant1/Interfaces/0 \
fi.w1.wpa_supplicant1.Interface.TDLSTeardown string:<peer-mac-address>
yields no error
dbus-send --system --dest=fi.w1.wpa_supplicant1 --print-reply \
/fi/w1/wpa_supplicant1/Interfaces/0 \
fi.w1.wpa_supplicant1.Interface.TDLSStatus string:<peer-mac-address>
yields: string "peer not connected"
Signed-hostap: Paul Stewart <pstew@chromium.org>
During persistent group re-invocation, GO may end up using a different
channel as the operation channel compared to what was indicated in the
invitation frames. This may break the connection if the peer device ends
up scanning the GO only on the channel from the invitation frame. Fix
this by using the negotiated channel (if available) on the GO as the
operating channel instead of the channel that was provided in the
p2p_invite command to start negotiation.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
We were not filtering the EVENT_CHANNEL_LIST_CHANGED events based on the
regulatory hint initiator. So wait for EVENT_CHANNEL_LIST_CHANGED event
after our own change was triggered even when regulatory hint initiator
was the driver. This could result in the wait for the channel list to be
updated to be terminated before the real change has occurred and as
such, old channel list remaining in use when configuring
hostapd/wpa_supplicant country parameter. Fix this by filtering the
hints according to the initiator and only regulatory hints initiated by
user will be used to stop the wait.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
If hostapd was started with the interface already in AP mode, leave the
interface in AP mode on deinit instead of unconditionally forcing it to
station mode.
Signed-hostap: Jouni Malinen <j@w1.fi>
It is common to build wpa_supplicant with AP mode support and it is
justifiable to clean up driver_nl80211.c by removing the conditional
build blocks based on hostapd vs. wpa_supplicant builds.
Signed-hostap: Jouni Malinen <j@w1.fi>
This gets rid of some ifdef HOSTAPD constructs and shares more
of the initialization code between hostapd and wpa_supplicant.
Signed-hostap: Jouni Malinen <j@w1.fi>
These variables were originally used in hostapd to clear HT channel
information when exiting. However, that functionality was lost with
commit f019981aee when moving to a common
code for setting the channel. Taken into account that no one seems to
have missed this functionality over the last four years, it seems safe
to drop this rather than try to fix the old hostapd behavior.
Signed-hostap: Jouni Malinen <j@w1.fi>
It's not possible to get a raw private key from keystore anymore, so
this would fail every time anyway. Remove it so it doesn't confuse
anyone that looks at this code.
Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
The new keystore ENGINE is usable to perform private key operations when
we can't get the actual private key data. This is the case when hardware
crypto is enabled: the private key never leaves the hardware.
Subsequently, we need to be able to talk to OpenSSL ENGINEs that aren't
PKCS#11 or OpenSC. This just changes a few #define variables to allow us
to talk to our keystore engine without having one of those enabled and
without using a PIN.
Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
If remaining AP session timeout is less than 5 seconds
for an existing station, replenish the timeout to 5 seconds.
This allows stations to be able to recycle a dialog token
value beyond 5 seconds for GAS exchange.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
eloop_replenish_timeout() finds a registered matching
<handler,eloop_data,user_data> timeout. If found, replenishes
the timeout if remaining time is less than the requested time.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
system/core/libnl_2 does not include nl_socket_set_nonblocking(), so
need to implement that to fix the build.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Add a parameter to send the overlapping BSS scan parameter
information element. This will require clients to perform
background scans to check for neigbors overlapping this
HT40 BSS. Since the implementation is incomplete it should
only be used for testing.
Signed-hostap: Paul Stewart <pstew@chromium.org>
If we are already connected to the selected AP with a network block
that was created based on the selected credential, do not force a
reconnection or network block update.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
It is possible for additional BSSs to be added while the primary
interface is still in the process of determining channel parameters (HT
co-ex scan, ACS, DFS). Do not enable secondary interfaces in such state
immediately, but instead, wait for the pending operation on the primary
interface to complete. Once that's done, the added extra BSSs will also
be enabled in hostapd_setup_interface_complete().
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Reject multiple calls to hostapd_setup_bss() for any specific interface.
hostapd_cleanup() must have been called first before trying to restart a
BSS.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
hostapd_bss_deinit() takes care of freeing the associated stations and
calling hostapd_cleanup() to deinit per-BSS services.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This reverts parts of commit 390e489c0d
that tried to enable removal of the first BSS. Since that operation is
now forced to remove all BSSs, these changes are not needed. The
hostapd_if_remove() operation in hostapd_free_hapd_data() is problematic
for the first BSS since it ends up freeing driver wrapper information
that is needed later when deinitializing the driver wrapper.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Since the control interface is now initialized as part of
hostapd_setup_interface(), it needs to be deinitialized on the error
path.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
If a secondary BSS is removed while it is waiting for the primary BSS to
complete channel setup (e.g., due to HT co-ex scan, ACS, or DFS), the
hostapd_data instance has not yet been initialized. Fix the BSS removal
code to take this special case into account and not try to deinitialize
the hostapd_data instance that has not yet been started.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The changes in commit 5592065850 to allow
any BSS to be removed were a bit too early since there are still number
of areas that use the first BSS as a special case. Especially the
driver_ops API is going to require quite a bit of cleanup before removal
of the first BSS without the other BSSes of the same radio can be done
safely.
For now, force all BSSs to be removed in case the first one is removed.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This call requires a struct hostapd_data pointer and that is not really
something that the driver wrappers should be using.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
It looks like abs() result is signed and gcc warns about this when
running a build with -O0 but not with -O2.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Limit the calls to eloop_terminate() to happen only for the
initialization failure from the interfaces that we specified on the
command line. This allows hostapd process to continue operating even if
a dynamically added interface fails to start up. This allows the upper
layer software to fix a configuration error and retry.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
When WFD Subelements are set, the IE in the Beacon frames of already
existing groups are not updated. This patch fixes this issue by setting
beacon_update to be 1 on WFD IE update.
Signed-hostap: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
The allocation was not verified to complete successfully and the
allocated memory was not freed on error paths.
Signed-hostap: Adriana Reus <adriana.reus@intel.com>
hostapd_set_freq_param() rejected the 20 MHz channel case with
vht_enabled due to the existing validation step including only 5 GHz (to
be more exact, only >= 5000 MHz). While the behavior may not be fully
defined for 2.4 GHz, we can enable this based on driver capability
advertisement to fix automatic VHT selection for P2P use cases.
mac80211_hwsim advertises VHT for 2.4 GHz band and that resulted in
failures when trying to start GO on that band with vht=1 parameter.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
NL80211_ATTR_CENTER_FREQ1 is defined to be used for anything but 20 MHz
bandwidth, so it could be unset for 20 MHz channels. Do not use it to
override center frequency from NL80211_ATTR_WIPHY_FREQ (if available)
for 20 MHz channels to avoid clearing frequency.
Signed-hostap: Jouni Malinen <j@w1.fi>
Better share the same function for initializing control interface from
the two possible paths that can add a new interface to hostapd.
Signed-hostap: Jouni Malinen <j@w1.fi>
This is a per-BSS configuration parameter and as such, needs to be
configured to the driver from hostapd_setup_bss() instead of
hostapd_driver_init().
Signed-hostap: Jouni Malinen <j@w1.fi>
DFS operations are specific to the interface (radio/wiphy), not BSS
(netdev/vif), so hostapd_iface is the appropriate element to use in
them.
Signed-hostap: Jouni Malinen <j@w1.fi>
If per-BSS configuration enabling did not provide a phy name, iface->phy
was left empty. It can be helpful to set this up automatically, so fill
that when initializing the interface.
Signed-hostap: Jouni Malinen <j@w1.fi>
Only scan the affected channels instead of all enabled channels when
determining whether the primary and secondary channel for HT40 needs to
be swapped. This speed up HT40 setup considerably on 5 GHz band.
Signed-hostap: Jouni Malinen <j@w1.fi>
If hostapd is requested to set the country code and the previous country
code differs from the new one, the channel list information from the
driver may change. This change may not be instant, so wait for an
EVENT_CHANNEL_LIST_CHANGED event before continuing interface setup with
fetching of the channel list information. This fixes issues where the
selected channel is not available based on the previous regulatory data
and update through CRDA takes some time.
Signed-hostap: Jouni Malinen <j@w1.fi>
Channel determination may take considerable time when ACS or DFS is
used, so it is useful to be able to observe this process through the
control interface. Move the initialization of the control interfaces to
happen before channel determination so that this can be achieved.
Signed-hostap: Jouni Malinen <j@w1.fi>
Use hostapd_interface_init2() for all interfaces instead of the
previously used different paths for per-interface-config and
per-BSS-config cases. This moves the calls to hostapd_driver_init() and
hostapd_setup_interface() to happen after all configuration files have
been read.
Signed-hostap: Jouni Malinen <j@w1.fi>
While these attributes may be expected to be present always, this needs
to be verified within driver_nl80211.c since we cannot depend on the
kernel/driver working correctly.
Signed-hostap: Jouni Malinen <j@w1.fi>
Previously, ENABLE command ended up freeing the hostapd_iface context on
initialization failures, but did not even remove the interface from the
list of available interfaces. This resulted in use of freed memory with
any following operation on the same interface. In addition, removing the
interface on initialization failure does not seem like the best
approach. Fix both of these issues by leaving the interface instance in
memory, but in disabled state so that the configuration can be fixed and
ENABLE used again to enable the interface or REMOVE used to remove the
interface.
Signed-hostap: Jouni Malinen <j@w1.fi>
Number of regressions had shown up in wpa_supplicant implementation of
SAE group selection due to different integer array termination (-1 in
hostapd, 0 in wpa_supplicant) being used for SAE groups. The
default_groups list did not seem to use any explicit termination value.
In addition, the sae_group_index was not cleared back to 0 properly
whenever a new SAE session was started.
Signed-hostap: Jouni Malinen <j@w1.fi>
When removing and re-adding the first wlan# netdev to hostapd
dynamically, the netdev is already present and should not be removed and
re-added to maintain its state as not-added-by-hostapd so that it does
not get removed automatically.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The global control interface command "REMOVE <ifname>" can now be used
to remove a single virtual interface (BSS) without affecting other
virtual interfaces on the same radio.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The global control interface command "ADD
bss_config=<phyname>:<config file>" can now be used to add a single
virtual interface (BSS) to an interface.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This moves the vif added check from core hostapd to the driver wrapper
(only driver_nl80211.c uses this) and reorders operations a bit to allow
the first BSS (vif) to be removed from a multi-BSS setup.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The first user of monitor interface was not counted and that could
result in the monitor interface getting removed if the initial interface
was removed from a multi-BSS setup.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Return control flow to hostapd by calling hostapd_acs_completed()
if requesting a scan from the underlying device fails.
Signed-hostapd: Helmut Schaa <helmut.schaa@googlemail.com>
If radar was detected single BSS is notified about it. This caused only
that single BSS to be stopped and restarted. However, due to nl80211
interface combinations the BSS was not started on a new channel and
other BSSes remained operating on the old channel.
The downside is that hostapd_disable_iface() causes deauth frames to be
sent. This is undesired but on the other hand it doesn't make sense to
create workarounds that imitate CSA's 'block tx'. For proper Tx
quiescing CSA should be properly implemented.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Decouple HT/VHT offset/center-freq calculations from channel lookup.
This will be necessary for further improvements on the DFS codebase.
Signed-hostap: Michal Kazior <michal.kazior@tieto.com>
The GTK rekey offload information was sent to the driver immediately
after the 4-way handshake which ended up being before the initial group
key exchange in the case of WPA (v1). This could result in even that
initial GTK handshake being offloaded and wpa_supplicant being left in
WPA_GROUP_HANDSHAKE state. Fix this by postponing the operation to
happen only after the full set of initial EAPOL-Key exchanges have been
completed (i.e., in the existing location for WPA2 and a after the group
key handshake for WPA).
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Reject RELOAD control interface command if the dynamic configuration
changes have resulted into a state where the configuration is invalid.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This allows the configuration validation routines to be called from
src/ap/*.c for runtime updates of configuration without reprocessing the
full configuration file.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This provides a new option for configuring multiple virtual interfaces
(BSS) that share a single radio. The new command line parameter
-b<phyname>:<config file name> is used to define one or more virtual
interfaces for each PHY. The first such entry for a new PHY is used to
initialize the interface structure and all consecutive parameters that
have the same PHY name will be added as virtual BSS entries to that
interface. The radio parameters in the configuration files have to be
identical.
This can be used as an alternative for the bss=<ifname> separator and
multiple BSSes in a single configuration file design while still
allowing hostapd to control the PHY (struct hostapd_iface) as a group of
virtual interfaces (struct hostapd_data) so that common radio operations
like OLBC detection and HT40 co-ex scans can be done only once per real
radio.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This makes it more convenient to move BSS configuration entries between
struct hostapd_config instances to clean up per-BSS configuration file
design.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This may be needed if the wpa_psk information for previously derived
from passphrase and either the SSID or the passphrase has changed.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Instead of duplicating the functionality and missing changes (like the
hostapd_broadcast_wep_clear() call), use the hostapd_clear_old()
function that was already used for the similar case with configuration
file reload.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Start GO with VHT support if VHT option was requested
and the appropriate channels are available.
Signed-hostap: Eliad Peller <eliadx.peller@intel.com>
Add the option to ask for VHT operation similarly to the way ht40 is
configured - either by adding 'vht' param to the relevant p2p_*
commands or by configuring p2p_go_vht=1 in the configuration file.
This patch only adds the configuration option (e.g., via control
interface). The actual handling of the VHT parameter (asking the driver
to use VHT, etc.) will be done by the following patch.
Signed-hostap: Eliad Peller <eliadx.peller@intel.com>
Later on, we'll consider the availability of these
channels when starting P2P GO with VHT support.
Signed-hostap: Eliad Peller <eliadx.peller@intel.com>
Mask the remote VHT capabilities with our own capabilities, similarly
to what is done for HT capabilities.
Signed-hostap: Eliad Peller <eliadx.peller@intel.com>
Make sure the driver supports 160/80+80 MHz VHT capabilities
before trying to configure these channels.
Signed-hostap: Eliad Peller <eliadx.peller@intel.com>
VHT_CAP_BEAMFORMEE_STS_MAX, VHT_CAP_SOUNDING_DIMENSION_OFFSET, and
VHT_CAP_MAX_A_MPDU_LENGTH_EXPONENT were not defined properly (wrong
name/size). Fix that and update the hostapd.conf parsing accordingly.
Signed-hostap: Eliad Peller <eliadx.peller@intel.com>
Previously the Country element contained the max TX power the local
hardware was capable of. Change this to just use the regulatory limit.
Signed-hostap: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
The new p2p_add_cli_chan=1 configuration parameter can be used to
request passive-scan channels to be included in P2P channel lists for
cases where the local end may become the P2P client in a group. This
allows more options for the peer to use channels, e.g., if the local
device is not aware of its current location and has marked most channels
to require passive scanning.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The new p2p_no_go_freq frequency range list (comma-separated list of
min-max frequency ranges in MHz) can now be used to configure channels
on which the local device is not allowed to operate as a GO, but on
which that device can be a P2P Client. These channels are left in the
P2P Channel List in GO Negotiation to allow the peer device to select
one of the channels for the cases where the peer becomes the GO. The
local end will remove these channels from consideration if it becomes
the GO.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
When we have CAC active and receive a radar event, we should ignore
CAC_ABORT event and handle channel switch in the radar event handler.
Signed-hostap: Janusz Dziedzic <janusz.dziedzic@tieto.com>
This fixes a problem when operating on non-DFS channel and receiving a
radar event for that channel. Previously, we would have decided to
switch channels.
Signed-hostap: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Add a table of available VHT80 channels. This table contains the first
available channel. We will also choose this first channel as the control
one.
Signed-hostap: Janusz Dziedzic <janusz.dziedzic@tieto.com>
To avoid a problem where the beacon socket occasionally
blocks, mark any sockets on the eloop as non-blocking.
The previous patch reordered the code to never send a
command after a socket was put on the eloop, but now also
invalidate the nl handle pointer while it's on there.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
Abstract the handling of sockets on the eloop to avoid
destroying sockets still on the eloop and also to allow
the next patch to mark the socket non-blocking.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
The IBSS code registers the bss nl_mgmt socket for auth
frames when the join event happens, but that is too late
as then the socket is already on the eloop, which could
cause problems when other events are received at the
same time as the registration is done.
Move the auth frame registration to the initial setup
before the socket is put onto the eloop.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
Some driver wrappers may implement this by writing eight octets even
though IPN is only six octets. Use a separate WPA_KEY_RSC_LEN (8) octet
buffer in the call to make sure there is enough buffer room available
for the full returned value and then copy it to IPN field.
The previous implementation used the following igtk field as the extra
buffer and then initialized that field afterwards, so this change does
not fix any real issue in behavior, but it is cleaner to use an explicit
buffer of the maximum length for get_seqnum().
Signed-hostap: Jouni Malinen <j@w1.fi>
Even though the length of this buffer is based only on locally
configured information, it is cleaner to include explicit buffer room
validation steps when adding the attributes into the buffer.
Signed-hostap: Jouni Malinen <j@w1.fi>
linux_br_get() was forcing null termination on the buffer, but did not
check whether the string could have been truncated. Make this more
strict by rejecting any truncation case.
Signed-hostap: Jouni Malinen <j@w1.fi>
The allocation of new_bss and its use was separated by a lot of code in
this function. This can be cleaned up by moving the allocation next to
the use, so that this all can be within a single #ifdef HOSTAPD block.
The i802_check_bridge() call was outside type == WPA_IF_AP_BSS case, but
in practice, it is only used for WPA_IF_AP_BSS (and if used for
something else, this would have resulted in NULL pointer dereference
anyway).
Signed-hostap: Jouni Malinen <j@w1.fi>
If SSL_CTX_new() fails in tls_init(), the per-SSL app-data allocation
could have been leaked when multiple TLS instances are allocated.
Signed-hostap: Jouni Malinen <j@w1.fi>
The VHT_CHANWIDTH_160MHZ case fell through to the default case and
printed out a debug message that was not supposed to be shown here.
Signed-hostap: Jouni Malinen <j@w1.fi>
os_strlpcy() should be used instead of os_strncpy() to guarantee null
termination. Since there are no remaining strncpy uses, remove
os_strncpy() definition.
Signed-hostap: Jouni Malinen <j@w1.fi>
This was already included in all the other calls to eap_proxy, but
somehow the get_imsi call had been forgotten.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Trying to access the SIM card details without checking if the eap_proxy
layer has been initialized can results in a crash. Address this by
sending the request for the IMSI through eapol_supp_sm.c which can
verify that eap_proxy has been initialized.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Previously ACS required valid survey data on all available channels.
This can however not be guaranteed. Instead of just failing, fall back
to the subset of channels that have valid ACS data.
Signed-hostap: Helmut Schaa <helmut.schaa@googlemail.com>
Otherwise hostapd might hang doing nothing anymore. Propagate ACS
errors so we can fail gracefully.
Signed-hostap: Helmut Schaa <helmut.schaa@googlemail.com>
If ACS fails we still need to call hostapd_setup_interface_complete.
Otherwise hostapd will just hang doing nothing anymore. However, pass
an error to hostapd_setup_interface_complete to allow a graceful fail.
Signed-hostap: Helmut Schaa <helmut.schaa@googlemail.com>
This makes it easier to go through the P2P channel list operations in
the debug log without having to parse through the hexdump manually.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Incorrect nla_get variants were used to get event type and frequency.
Kernel passes both as u32. This caused issues on tinynl/big-endian hosts
- CAC finished was treated as radar detection and frequency was 0.
Signed-hostap: Michal Kazior <michal.kazior@tieto.com>
It is possible for a vif netdev to be removed by something else than
hostapd and if that happens for a virtual AP interface, if_remove()
handler should still free the local data structure to avoid memory leaks
if something external removes a netdev.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Previously, the send_mlme->send_frame->send_frame_cmd path that could be
used when a GO sends an offchannel Action frame ended up not updating
drv->send_action_cookie. This can result in an issue with not being able
to cancel wait for the response, e.g., in invitation-to-running-group
case.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This fixes issues where a GO used offchannel-TX operation to send an
Invitation Request frame. Wait for the offchannel TX operation needs to
be stopped as soon as the Invitation Response frame has been received.
This addresses some issues where Probe Response frame from the GO
through the monitor interface may end up going out on a wrong channel
(the channel of this offchannel TX operation for invitation).
Signed-hostap: Jouni Malinen <j@w1.fi>
Join-a-group needs to force the current operating channel of the target
group as the frequency to use for the PD exchange. When the channel was
selected based on a BSS entry for the GO, this worked only for the first
PD Request frame while the retries reverted to a potentially different
channel based on a P2P peer entry. Fix this by maintaining the forced
channel through the PD retry sequence.
Signed-hostap: Jouni Malinen <j@w1.fi>
P2P Invitation Response frame is required to include the Channel List
attribute only in Status=Success case. Skip the debug message claiming
that a mandatory attribute was not included in non-Success case.
Signed-hostap: Jouni Malinen <j@w1.fi>
This allows the new external_sim=1 case to be used to perform UMTS
authentication step in EAP-AKA/AKA' peer process. Following control
interface event is used to request the operation:
CTRL-REQ-SIM-<network id>:UMTS-AUTH:<RAND>:<AUTN> needed for SSID <SSID>
Response from external processing is returned with
CTRL-RSP-SIM-<network id> UMTS-AUTH:<IK>:<CK>:<RES>
or
CTRL-RSP-SIM-<network id> UMTS-AUTS:<AUTS>
Signed-hostap: Jouni Malinen <j@w1.fi>
This allows the new external_sim=1 case to be used to perform GSM
authentication step in EAP-SIM peer process. Following control interface
event is used to request the operation:
CTRL-REQ-SIM-<network id>:GSM-AUTH:<RAND1>:<RAND2>[:<RAND3>] needed
for SSID <SSID>
For example:
<3>CTRL-REQ-SIM-0:GSM-AUTH:5e3496ce7d5863b3b09f97f565513bc3:
73f0f0bc5c47bcbed6f572d07ab74056:447b784f08de80bdc2b1e100fccbb534
needed for SSID test
Response from external processing is returned with
CTRL-RSP-SIM-<network id> GSM-AUTH:<Kc1>:<SRES1>:<Kc2>:<SRES2>
[:<Kc3>:<SRES3>]
For example:
wpa_cli sim 0 GSM-AUTH:d41c76e0079247aa:2709ebfb:43baa77cfc8bcd6c:
0fa98dc1:a8ad1f6e30e
Signed-hostap: Jouni Malinen <j@w1.fi>
The new configuration parameter external_sim=<0/1> can now be used to
configure wpa_supplicant to use external SIM/USIM processing (e.g., GSM
authentication for EAP-SIM or UMTS authentication for EAP-AKA). The
requests and responses for such operations are sent over the ctrl_iface
CTRL-REQ-SIM and CTRL-RSP-SIM commands similarly to the existing
password query mechanism.
Changes to the EAP methods to use this new mechanism will be added in
separate commits.
Signed-hostap: Jouni Malinen <j@w1.fi>
This makes it easier to handle cases where the application is restarted
and the previously used local TCP port may not have been fully cleared
in the network stack.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The new bss_load_test parameter can be used to configure hostapd to
advertise a fixed BSS Load element in Beacon and Probe Response frames
for testing purposes. This functionality is disabled in the build by
default and can be enabled with CONFIG_TESTING_OPTIONS=y.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Indicate support for QoS Mapping and configure driver to update the QoS
Map if QoS Map Set elements is received from the AP either in
(Re)Association Response or QoS Map Configure frame.
This commit adds support for receiving the frames with nl80211 drivers,
but the actual QoS Map configuration command is still missing.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This allows QoS Map Set element to be added to (Re)Association Response
frames and in QoS Map Configure frame. The QoS Mapping parameters are
also made available for the driver interface.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The new domain_suffix_match (and domain_suffix_match2 for Phase 2
EAP-TLS) can now be used to specify an additional constraint for the
server certificate domain name. If set, one of the dNSName values (or if
no dNSName is present, one of the commonName values) in the certificate
must have a suffix match with the specified value. Suffix match is done
based on full domain name labels, i.e., "example.com" matches
"test.example.com" but not "test-example.com".
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Add DFS structures/events handlers, CAC handling, and radar detection.
By default, after radar is detected or the channel became unavailable, a
random channel will be chosen.
This patches are based on the original work by Boris Presman and
Victor Goldenshtein. Most of the DFS code is moved to a new dfs.c/dfs.h
files.
Cc: Boris Presman <boris.presman@ti.com>
Cc: Victor Goldenshtein <victorg@ti.com>
Signed-hostap: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-hostap: Janusz Dziedzic <janusz.dziedzic@tieto.com>
When hostapd receives an auth frame during ACS the transmission of
the according auth response will always fail:
ACS: Automatic channel selection started, this may take a bit
[..]
send_auth_reply: send: Resource temporarily unavailable
[..]
However, a station info entry was created. Once ACS is finished
it will flush all stations even though hapd was not yet fully
initialized. This results in a segfault when trying to access
hapd->radius:
0 0x0042c1c0 in radius_client_flush_auth ()
1 0x00416a94 in ap_free_sta ()
2 0x00416cc0 in hostapd_free_stas ()
3 0x0040bce8 in hostapd_flush_old_stations ()
4 0x0040c790 in hostapd_setup_interface_complete ()
5 0x0046347c in acs_scan_complete ()
6 0x0040f834 in hostapd_wpa_event ()
7 0x0043af08 in send_scan_event.part.46 ()
8 0x00443a64 in send_scan_event ()
9 0x00443c24 in do_process_drv_event ()
10 0x004449e8 in process_global_event ()
11 0x7767d7d0 in ?? ()
Fix this by not presuming anything about the initialization state of
hapd and checking ->radius before accessing.
Signed-off-hostapd: Helmut Schaa <helmut.schaa@googlemail.com>
In noisy environment peer may take more time to send Invitation
Response so increase Invitation Response timeout to 500 ms in success
case and also increase Invitation Request action wait time to 500 ms.
This makes the Invitation Request case use the same timeout with GO
Negotiation.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
A new TDLS request shall transmit TPK M1 frame with a unique INonce.
Thus a new explicit request would fail an ongoing TDLS negotiation with
the error "TDLS: FTIE SNonce in TPK M3 does not match with FTIE SNonce
used in TPK M1" if the peer happens to receive two M1 frames before an
M3 frame. Check for the ongoing negotiation with the peer and do not
start a new one if we are already in a setup negotiation with the peer.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
There is no need to go through the peer list when we already have a
pointer to the specific peer entry.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This is called from number of locations and it is more efficient to use
a new helper function instead of wpa_tdls_disable_link() that would do
peer address search from the list of peers.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Making this function be used only for external setup case simplifies the
implementation and makes core wpa_supplicant calls in ctrl_iface.c and
events.c consistent.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Commit 8a9f58f2cc ("EAP-AKA server: Store
permanent username in session data") broke AUTS processing by skipping
new authentication triplet fetch after having reported AUTS. Fix this by
started new full authentication sequence immediately after reporting
AUTS so that the updated parameters are available for the Challenge
message.
Signed-hostap: Jouni Malinen <j@w1.fi>
STATUS-DRIVER command can now be used to fetch driver interface status
information. This is mainly for exporting low-level driver interface
information for debug purposes.
Signed-hostap: Jouni Malinen <j@w1.fi>
TX frequency gets lost when going through the monitor send MLME option
and this resulted in P2P operations like invitation from a GO failing
when the driver needs monitor socket, but would support offchannel TX.
Fix this by using frame_cmd path instead in case the monitor socket
would have been hit for action frame TX.
Signed-hostap: Jouni Malinen <j@w1.fi>
Previously, IBSS mode (NL80211_IFTYPE_ADHOC) was left in drv->nlmode
when leaving IBSS. This causes issues for send_mlme() handler for P2P
Probe Response transmission in Listen state. Fix this by clearing nlmode
back to NL80211_IFTYPE_STATION on leaving IBSS so that following P2P
operations can be executed correctly. Previously, this was fixed only
when the next authentication/association attempt in station mode
occured.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
There is no need to use the bss variable which is used only within a
wpa_printf() call that can be conditionally removed from the build.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This extends hostapd global control interface command "ADD" to use a
configuration file instead of requiring configuration to be built using
SET command.
The command format is now following:
ADD <ifname> <control path|config=<path to config>>
For example:
ADD wlan0 /var/run/hostapd
ADD wlan0 config=/tmp/hostapd.conf
When using the configuration file option, ctrl_interface parameter in
the file needs to be set to allow ENABLE command to be issued on the new
interface.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
There was a comment about the the cleanup steps being from
hostapd_cleanup_iface(). However, the operations that cleared some
security parameters do not seem to exist elsewhere and do not make sense
here. Remove them to avoid changing configuration with DISABLE followed
by ENABLE.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This fixes some issues where dynamic interface enable/disable cycles
could end up trying to free resources twice and crash the process while
doing so.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This can be useful in figuring out how drv->last_mgmt_freq gets set
to debug issues with P2P frames being sent on incorrect channel.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
printf_decode() fills in a binary buffer and returns the length of
the written data. This did not use null termination since initial
use cases used the output as a binary value. However, Hotspot 2.0
cred block values are also using this for parsing strings. Those
cases could end up without proper null termination depending on what
os_malloc() ends up getting as the memory buffer. Fix these and make
printf_decode() more convenient by forcing the output buffer to be
null terminated.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
When no other user preference is specified, opt to use an operating
channel that allows 5 GHz band to be used rather than 2.4 GHz.
Previously, this was already done in practice for HT40 channels since no
such channel is enabled for P2P on 2.4 GHz. This commit extends this to
apply 5 GHz preference for 20 MHz channels as well.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
H3C WA2620i-AGN AP may send an EAP packet with an undefined EAP code
10 after successful EAP authentication which restarts the EAPOL
state machine. Drop such frames with this unrecognized code without
advancing the EAPOL supplicant or EAP peer state machines to avoid
interoperability issues with the AP.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
There is no point in updating the RNonce for every obtained TPK M1 frame
(e.g., retransmission due to timeout) with the same INonce (SNonce in
FTIE). Update RNonce only if a TPK M1 is received with a different
INonce (new TDLS session) to avoid issues with two setup exchanges
getting mixed and exchange failing due to mismatching nonces ("TDLS:
FTIE ANonce in TPK M3 does not match with FTIE ANonce used in TPK M2").
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Clear the peer information and disable the created link on a
failed TDLS setup negotiation. This is needed to avoid leaving
TDLS setup pending and to return to the AP path in case anything
goes wrong during the setup attempt.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Some APs may incorrectly change Device Password ID from PBC in M1 to
Default PIN in M2 even when they are ready to continue with PBC. This
behavior used to work with earlier implementation in wpa_supplicant, but
commit b4a17a6ea7 started validating this
as part of a change that is needed to support NFC configuration method.
While this kind of AP behavior is against the WSC specification and
there could be potential use cases for moving from PBC to PIN, e.g., in
case of PBC session overlap, it is justifiable to work around this issue
to avoid interoperability issues with deployed APs. There are no known
implementations of PBC-to-PIN change from M1 to M2, so this should not
reduce available functionality in practice.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
It is possible for the GO of a persistent group to change the PSK or
remove a client when per-client PSKs are used and this can happen
without the SSID changing (i.e., the group is still valid, but just not
for a specific client). If the client side of such persistent group ends
up trying to use an invalidated persistent group information, the
connection will fail in 4-way handshake. A new WPS provisioning step is
needed to recover from this.
Detect this type of case based on two 4-way handshake failures when
acting as a P2P client in a persistent group. A new
"P2P-PERSISTENT-PSK-FAIL id=<persistent group id>" event is used to
indicate when this happens. This makes it easier for upper layers to
remove the persistent group information with "REMOVE_NETWORK <persistent
group id>" if desired (e.g., based on user confirmation).
In addition to indicating the error cases for persistent groups, all
this type of PSK failures end up in the client removing the group with
the new reason=PSK_FAILURE information in the P2P-GROUP-REMOVED event.
Signed-hostap: Jouni Malinen <j@w1.fi>
The new control interface command P2P_REMOVE_CLIENT <P2P Device
Address|iface=Address> can now be used to remove the specified client
from all groups (ongoing and persistent) in which the local device is a
GO. This will remove any per-client PSK entries and deauthenticate the
device.
Signed-hostap: Jouni Malinen <j@w1.fi>
Record all generated per-client PSKs in the persistent group network
block and configure these for the GO Authenticator whenever re-starting
the persistent group. This completes per-client PSK support for
persistent groups.
Signed-hostap: Jouni Malinen <j@w1.fi>
When using per-device PSKs, select the PSK based on the P2P Device
Address of the connecting client if that client is a P2P Device. This
allows the P2P Interface Address to be changed between P2P group
connections which may happen especially when using persistent groups.
Signed-hostap: Jouni Malinen <j@w1.fi>
This can be used to implement per-device PSK selection based on the
peer's P2P Device Address instead of P2P Interface Address.
Signed-hostap: Jouni Malinen <j@w1.fi>
This makes the P2P Device Address of the Enrollee available with the PSK
records to allow P2P Device Address instead of P2P Interface Address to
be used for finding the correct PSK.
Signed-hostap: Jouni Malinen <j@w1.fi>
"wpa_cli p2p_set per_sta_psk <0/1>" can now be used to disable/enable
use of per-device PSKs in P2P groups. This is disabled by default.
When enabled, a default passphrase is still generated by the GO for
legacy stations, but all P2P and non-P2P devices using WPS will get
a unique PSK.
This gives more protection for the P2P group by preventing clients from
being able to derive the unicast keys used by other clients. This is
also a step towards allowing specific clients to be removed from a group
reliably without having to tear down the full group to do so.
Signed-hostap: Jouni Malinen <j@w1.fi>
Even after listen duration is over, P2P module remained in
P2P_LISTEN_ONLY state, which is blocking station mode scans. Fix this by
stopping P2P listen explicitly to update p2p_state to IDLE when listen
duration expires.
Signed-hostap: Syed Asifful Dayyan <syedd@broadcom.com>
This adds ACS support to hostapd. Currently only survey-based
algorithm is available.
To use ACS you need to enable CONFIG_ACS=y in .config and use
channel=0 (or channel=acs_survey) in hostapd.conf.
For more details see wiki page [1] or comments in src/ap/acs.c.
[1]: http://wireless.kernel.org/en/users/Documentation/acs
Signed-hostap: Michal Kazior <michal.kazior@tieto.com>
Swisscom SIM cards do not include MNC length within EF_AD, and end up
using incorrect MNC length based on the 3-digit default. Hardcode MNC
length of 2 for Switzerland, in the same manner as it was done for
Finland.
Signed-hostap: Andrejs Cainikovs <andrejs.cainikovs@sonymobile.com>
If the device that sends the GO Negotiation Confirm becomes the GO, it
may change its operating channel preference between GO Negotiation
Request and Confirm messages based on the channel list received from us.
Previously, the peer operating channel preference was not updated in
such a case and this could result in the initial scans after GO
Negotiation using incorrect operating channel and as such, extra delay
in the connection process. Fix this by updating the operating channel
information from GO Negotiation Confirm in cases where the peer becomes
the GO.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
If there are no higher priority preference for the operating channel,
use the first pref_chan entry as the operating channel preference over
the pre-configured channel which is not really a good indication of
preference. This changes the behavior for GO Negotiation Request frame
operating channel preference value in cases where p2p_pref_chan list is
set.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This new control interface event message is used to indicate when
both 4-way handshakes have been completed with a new IBSS peer.
Signed-hostap: Jouni Malinen <j@w1.fi>
This adds survey dump support for all frequencies
and for specific desired frequencies. This will later
be used by ACS code for spectrum heuristics.
Signed-hostap: Michal Kazior <michal.kazior@tieto.com>
This splits up the channel checking upon initialization into a few
helpers. This should make this a bit easier to follow. This also paves
the way for some initial ACS entry code.
Signed-hostap: Michal Kazior <michal.kazior@tieto.com>
Interfaces that take one or two seconds to reconfigure the link after we
set IFF_ALLMULTI or after we bring the interface up were dropping the
initial TX EAPOL packet which caused excessive delays in authentication.
This change applies to FreeBSD/DragonFly only.
Signed-hostap: Rui Paulo <rpaulo@FreeBSD.org>
Add additional input verification for the frequency parameter in
p2p_group_add (and other P2P operations for that matter). Without this
verification invalid freq could be set and not handled properly.
Signed-hostap: Ilan Peer <ilan.peer@intel.com>
According to WSC specification (Ver 2.0.2, section 8.3), RF Bands
attribute should be set to the specific RF band used for the current
message. Add an option to set wanted band in wps_build_rf_bands() and
add a callback to get the current band from wpa_supplicant and hostapd.
Signed-hostap: David Spinadel <david.spinadel@intel.com>
It is possible that when trying to remove a dynamically added interface,
changing its type to station mode is not possible (since the kernel does
not support so in its interface combinations).
Since P2P interfaces are always dynamically added, avoid changing their
type to station in the deinit_ap() and deinit_p2p_client() nl80211
callbacks, assuming that the interface is about to be removed.
Signed-hostap: Ilan Peer <ilan.peer@intel.com>
The pad field in the RRB messages is unused, but it should be
initialized to avoid sending out arbitrary data from stack. This was
also generating number of valgrind complaints about uninitialized memory
accesses in local FT tests.
Signed-hostap: Jouni Malinen <j@w1.fi>
Commit 8e12685c43 replaced call to
nl80211_mgmt_unsubscribe() on the deinit path with a
wpa_driver_nl80211_set_mode() call. This is not enough to unregister the
bss->nl_mgmt read socket in all cases. Fix this by unconditionally
unsubscribing from the nl80211 events after having change mode to
station.
Signed-hostap: Jouni Malinen <j@w1.fi>
drv->assoc_freq was not updated during the connect command (neither
during the command's invocation nor after getting the event) unlike with
auth/assoc case where assoc_freq is updated. This resulted in
nl80211_get_link_noise() (and any other function for that matter) using
the improper drv->assoc_freq value with drivers that use the connect
API. Fix this by updating drv->assoc_freq on connect command and when
fetching the frequency from the driver.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Stop AP command can be used by the driver as an event to indicate that
AP mode has stopped operation. WLAN driver may have encountered errors
that has forced the driver to report this event or concurrent operations
on virtual interfaces may have forced AP operation to be stopped. When
in P2P GO mode, wpa_supplicant uses this event to remove P2P group to
keep in sync with the driver state.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
A transmission failure of the TDLS Setup Request frame (TPK Handshake
M1) results in no further retries and the peer entry being left in state
where all TDLS Setup Request frames from the peer with higher address
would be rejected, thus always resulting in a failure to establish a
TDLS link. Handle the failures in transmission by disabling the link
immediately to ensure the traffic to the peer goes through the AP. This
commit also handles similar transmision failures for TPK Handshake M2
and M3 frames (TDLS Setup Response and Confirm).
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The nl80211 command for setting the TX index does not distinguish TDLS
vs. AP key and as such, the driver would not know what this set TX key
index operation is doing in the TDLS case. This could result in the TX
key index for AP being changed instead if static WEP is used in the AP
connection. Fix the issue by not setting TX key index when configuring a
TDLS key.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This is not used anymore after the previous commits that changed the
driver interface to use number of supported concurrent channels instead
of this flag.
Signed-hostap: Ilan Peer <ilan.peer@intel.com>
Signed-hostap: David Spinadel <david.spinadel@intel.com>
Previously, drivers only reported if they support multiple concurrent
channels, but did not report the maximum number of supported channels.
Add this reporting to the driver capabilities and add the implementation
to driver_nl80211.
Signed-hostap: Ilan Peer <ilan.peer@intel.com>
Signed-hostap: David Spinadel <david.spinadel@intel.com>
In order to correctly handle IBSS/RSN, wpa_supplicant has to register
for any incoming Authentication frmae to properly react when those are
received.
Signed-hostap: Nicolas Cavallari <cavallar@lri.fr>
Signed-hostap: Antonio Quartulli <antonio@open-mesh.com>
If the frequency is not specified the frame is now sent over
the channel used by the current BSS.
This will also log the payload of each sent CMD_FRAME.
Signed-hostap: Nicolas Cavallari <cavallar@lri.fr>
[antonio@open-mesh.com: commit message reworded]
Signed-hostap: Antonio Quartulli <antonio@open-mesh.com>
The static WEP keys have to be configured for the new VLAN
interface that is created for a 4addr WDS peer, not doing so
breaks WEP functionality in nl80211/4addr based WDS links.
Signed-hostap: Sujith Manoharan <c_manoha@qca.qualcomm.com>
This allows wpa_supplicant to associate to an AP that has VHT BSS
membership selector set to indicate VHT support is required for the BSS.
Without the patch it was impossible to connect to, e.g., hostapd-based
AP that has require_vht=1. wpa_supplicant was complaining with:
hardware does not support required rate 63.0 Mbps
Signed-hostap: Michal Kazior <michal.kazior@tieto.com>
In a AP/STA concurrent setup, if the STA interface is continually
scanning, trying to connect to a network, the AP interface
is basically broken since beaconing would be erratic.
This option can be used in a WDS setup where one AP acts as a
Client/AP-Repeater. The Repeater AP interface has to start beaconing
only after the Client interface has established a WDS link with the
"Root AP".
Signed-hostap: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Compiling hostapd with VHT enabled on a big endian machine resulted in
an undefined symbol error. Fix this by defining the missing macro.
Signed-hostap: Michal Kazior <michal.kazior@tieto.com>
Previously, there could be two disconnection events in core
wpa_supplicant when going through a case of wpa_supplicant-requested
disconnection with a driver that implements SME internally. This could
result in undesired behavior when a disconnection is followed by a new
connection attempt before the extra event has been received (e.g.,
during fast reassoc or WPS provisioning). Avoid such issues by ignoring
locally generated disconnect events after requesting cfg80211 to
disconnect.
This makes the previously used ignore_next_local_disconnect more
consistent by setting the variable within
wpa_driver_nl80211_disconnect() so that both callers get the same
behavior.
Signed-hostap: Jithu Jance <jithu@broadcom.com>
Commit 3962b65858 removed the Xcode
project files, but missed the defines in build_config.h. Remove these
since there are no users for them in the current snapshot.
Signed-hostap: Jouni Malinen <j@w1.fi>
The new server_id parameter in hostapd.conf can now be used to specify
which identity is delivered to the EAP peer with EAP methods that
support authenticated server identity.
Signed-hostap: Jouni Malinen <j@w1.fi>
Check that SSL_clear_options and SSL_CTX_clear_options are defined
before using them to avoid compilation failures with older OpenSSL
versions that did not include these macros.
Signed-hostap: Jouni Malinen <j@w1.fi>
Since the P2P_DEVICE support indication was added to kernel before
everything was working properly, there may be kernel versions in use
with the new mechanism breaking P2P functionality (especially with
mac80211_hwsim). For now, disable P2P_DEVICE support by default and
allow it to be enabled with driver_param=p2p_device=1 in the
configuration file. This default behavior may be changed in the future
once the kernel issues has been resolved in stable releases.
Signed-hostap: Jouni Malinen <j@w1.fi>
Another function that needs the wdev id when P2P management is done
using the P2P_DEVICE interface.
Signed-hostap: Arend van Spriel <arend@broadcom.com>
With P2P Device support there will be two interfaces with their
own MAC address. The P2P Interface Address must be unique so verify
it is.
Signed-hostap: Arend van Spriel <arend@broadcom.com>
The phy name was determined using /sys/class/net/<ifname> but the P2P
Device is not listed there since it does not have an associated net
device. This patch changes name determination to obtain the name from
the wiphy information provide by nl80211.
Signed-hostap: Arend van Spriel <arend@broadcom.com>
For P2P Device the netlink message should have wdev identifier
instead of the interface index. This fixes a failure which occurred
executing the P2P_GROUP_ADD command.
Signed-hostap: Arend van Spriel <arend@broadcom.com>
When using OpenSSL with TLS-based EAP methods, wpa_supplicant can now be
configured to use OCSP stapling (TLS certificate status request) with
ocsp=1 network block parameter. ocsp=2 can be used to require valid OCSP
response before connection is allowed to continue.
hostapd as EAP server can be configured to return cached OCSP response
using the new ocsp_stapling_response parameter and an external mechanism
for updating the response data (e.g., "openssl ocsp ..." command).
This allows wpa_supplicant to verify that the server certificate has not
been revoked as part of the EAP-TLS/PEAP/TTLS/FAST handshake before
actual data connection has been established (i.e., when a CRL could not
be fetched even if a distribution point were specified).
Signed-hostap: Jouni Malinen <j@w1.fi>
When P2P Device is used as P2P management interface the creation of the
P2P group interface fails because MAC address retrieval fails for the
P2P Device interface.
Signed-hostap: Arend van Spriel <arend@broadcom.com>
For P2P an interface may be created for the P2P client/group. The
create request is done on the P2P management interface, which may
be a P2P Device interface. In that case it needs to use the wdev_id.
Signed-hostap: Arend van Spriel <arend@broadcom.com>
In order to get a P2P-DEVICE-FOUND event the supplicant needs to
see a peer device during SEARCH and LISTEN phase. The SEARCH
phase does a scan so obtaining the scan results for the P2P Device
interface needs to be supported, i.e., use the wdev_id.
Signed-hostap: Arend van Spriel <arend@broadcom.com>
For P2P Device the MAC address is determined upon .init2(). The
wpa_s for this interface retrieves this address in
wpa_supplicant_update_mac_addr() using the .get_mac_addr() callback.
Signed-hostap: Arend van Spriel <arend@broadcom.com>
The function setting the interface mode also handles management
frame subscription. Rework it so subscription is done for the
P2P Device interface.
Signed-hostap: Arend van Spriel <arend@broadcom.com>
The driver uses linux_set_iface_flags() in several places. Introduce and
use i802_set_iface_flags() which also works for P2P Device interface.
Signed-hostap: Arend van Spriel <arend@broadcom.com>
The .deinit() closes netlink for P2P Device. Before doing that remove
the P2P Device interface that was created by wpa_supplicant.
Signed-hostap: Arend van Spriel <arend@broadcom.com>
Add specific handler for creating the P2P Device to store the wdev_id as
this type of interface does not have an interface index.
Signed-hostap: Arend van Spriel <arend@broadcom.com>
To support Android the kernel may have a "p2p0" netdev for a P2P Device
even though this isn't very useful, but Android requires a netdev. To
support this in the supplicant, if the interface mode is P2P_DEVICE,
re-set it to the same instead of STATION mode.
Note that this is only possible with a kernel that creates a
netdev for the P2P Device wdev.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
Add an option to pass a handler to nl80211_create_iface() and
nl80211_create_interface_once() that will be called after receiving the
message from the kernel. This handler will add the option to process the
message in different ways for different interfaces.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Add wdev_id to i802_bss. wdev_id_set indicates whether this id is
available. Use wdev_id if assigned, instead of ifindex. Use wdev_id for
events that come from the kernel to identify the relevant interface.
This commit does not assign wdev_id value for the BSS yet, i.e., this is
only preparation for the value to be used in a future commit.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Check the supported interfaces attribute to identify support for
a dedicated P2P Device interface type. If set, update the driver
capabilities flag to notify the supplicant.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Rename is_p2p_interface() to is_p2p_net_interface() since it used to
identify network P2P interfaces to disable 802.11b rates on them.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Sometimes an interface name that cannot be resolved is given to the
set_key function, so print the ifname in addition to the ifidx.
Signed-hostap: Michael Braun <michael-dev@fami-braun.de>
Currently, hostapd_get_vlan_id_ifname() is used to determine if a given
vlan is valid *and* to actually determine the interface. This leads to
wpa_set_keys() sometimes setting the key on the wildcard interface name,
which does not make sense.
This patch therefore adds hostapd_vlan_id_valid() and makes
hostapd_get_vlan_id_ifname() not return a wildcard interface.
Signed-hostap: Michael Braun <michael-dev@fami-braun.de>
Currently, struct hostapd_vlan is a per-BSS data structure which
also contains informations about whether to remove the bridge
or clear wlan / tagged-vlan interface from the bridge.
In a multi-interface multi-BSS setup, this can lead to the following
race condition:
1. wlan0 creates VLAN A, sets DVLAN_CLEAN_BR and DVLAN_CLEAN_VLAN_PORT
2. wlan1 creates VLAN A, does not set DVLAN_CLEAN_BR and
DVLAN_CLEAN_VLAN_PORT as already there
3. wlan0 removes VLAN A, removes tagged-interface from the bridge
but not the bridge.
Now wlan1 VLAN A is unusable due to the missing uplink.
4. wlan1 removes VLAN A, does not cleanup
Solution:
This requires an inter-BSS inter-interface data structure to track the
bridge / bridge port usage within hostapd. This data structure could
also be used to track any other device-has-been-created-by-hostapd
information or when regarding interface freeing.
Signed-hostap: Michael Braun <michael-dev@fami-braun.de>
Currently by default, all BSS share the bridge brvlan%d.
While this is sane when no tagged-interface is given, this
is insane when different tagged interfaces are given, as
it would result in bridging those tagged interfaces.
This patch therefore uses br%s%d with %s=tagged_interface
and %d=VLAN ID as bridge name when a tagged-interface is given.
Signed-hostap: Michael Braun <michael-dev@fami-braun.de>
Currently, when different BSS using different tagged vlan
interfaces, they are forced to share the bridge brvlan#,
which is not desirable.
This patch fixes this by making the bridge name configurable.
Signed-hostap: Michael Braun <michael-dev@fami-braun.de>
Add AVG_RSSI report to the signal_poll command if it is reported by
the kernel.
Signed-hostap: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-hostap: Ilan Peer <ilan.peer@intel.com>
Add prints for kernel event, including the event ID and event string.
Signed-hostap: David Spinadel <david.spinadel@intel.com>
Signed-hostap: Ilan Peer <ilan.peer@intel.com>
The ext_supp_rates passed to merge_byte_arrays would be invalid if not
advertized by the TDLS peer. Thus, validate the argument to avoid
crashes in such cases.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
If AP mode SME/MLME within wpa_supplicant is used for processing Probe
Request frames in GO mode, drop Probe Request frames that include only
802.11b rates per P2P spec section 2.4.1.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Upon association, disable the timer that removes the dummy STA. This
timer caused the STA that associates within 5 seconds of doing an ANQP
query to disassociate, thinking it's a dummy STA. Similar call was
already there for the SME/MLME-in-hostapd case in handle_auth(), but the
SME-in-driver case was not previously addressed.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
There is not much use for enabling WPA without WPA2 nowadays since most
networks have been upgraded to WPA2. Furthermore, the code size savings
from disabling just WPA2 are pretty small, so there is not much
justification for maintaining this build option. Remove it to get rid of
undesired complexity.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Commit ae8535b6e1 added a new function
wpa_sm_pmf_enabled() which is called from WNM code without ifdefs.
Define a dummy wrapper for this function to fix build if WPA2 is
disabled.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Commit 4033935dd9 updated
pmksa_cache_flush() function arguments, but forgot to update the wrapper
function for cases where WPA2 or EAP has been disabled in the build.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
In a noisy enviromment, some peers can be slow to respond to the
invitation request frames which may lead to unnecessary state timeout.
Increase this timeout to 350 ms to improve the probabilty of
successfully receiving the invitation response frames.
Signed-hostap: Vivek Natarajan <nataraja@qca.qualcomm.com>
This is needed for TDLS with VHT to allow partial AID to be set
correctly for the direct link frames. cfg80211 validation rules
prevented NL80211_ATTR_STA_AID from being used for this in set_station
case, so the new attribute is used instead.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Commit b4a17a6ea7 added support for the
WPS Registrar to change the Device Password based on WSC specification
design. However, this added validation for Registrar behavior which
resulted in preventing a common P2P use case from working. Relax the
validation rules for builds with P2P enabled to allow the Enrollee (P2P
client) accepting M1/M2 changes in Device Password Id between Default
and Registrar-specified PIN.
Signed-hostap: Jouni Malinen <j@w1.fi>
It looks like cfg80211 can deliver a deauth/disassoc event during some
roaming cases while we are already in progress with a new
authentication/association. This happens at least with FT protocol.
Avoid issues with such disconnection event resulting in core
wpa_supplicant stopping the new connection attempt by tracking
auth/assoc BSSID more carefully within driver_nl80211.c and filtering
out events that do not apply for the current AP.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The Michael MIC TX and RX keys needs to be swapped in the FT case just
like in all other TKIP key configuration cases. This fixes issues where
TKIP as group cipher resulted in Michael MIC failures being detected for
each received group-addressed frame after FT protocol use.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This cleans up debug log by not including comments about failed
operations in case the operation is known to fail due to not being
supported by the driver.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Enable MAC address based ACL for the drivers which advertise
this capabilty with NL80211_ATTR_MAC_ACL_MAX. Either of blacklist
or whitelist is supported, though, not simultaneously.
Signed-hostap: Vivek Natarajan <nataraja@qca.qualcomm.com>
Define a proper event prefix and include additional information to allow
ESS Dissassociation Imminent event to be used in a wpa_cli action
script.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This is needed to avoid allowing the STA to reconnect using a cached
PMKSA. ESS disassoc imminent notification is normally used to indicate
that the STA session will be terminated and as such, requiring full
authentication through the authentication server after this is needed.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
When STA interface is connected and P2P interface gets invited in a
different channel from previous P2P group, the invitiation would fail
because of no common channel found. Fix this by using different logic
when device support multi channel concurrency.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Commit c3fea27274 added a call to clear
all other PMKSA cache entries for the same network if the PMKSA cache
entry of the current AP changed. This was needed to fix OKC cases since
the other APs would likely use the new PMK in the future. However, this
ended up clearing entries in cases where that is not desired and this
resulted in needing additional full EAP authentication with networks
that did not support OKC if wpa_supplicant was configured to try to use
it.
Make PMKSA cache entry flushing more limited so that the other entries
are removed only if they used the old PMK that was replaced for the
current AP and only if that PMK had previously been used successfully
(i.e., opportunistic flag was already cleared back to 0 in
wpa_supplicant_key_neg_complete()). This is still enough to fix the
issue described in that older commit while not causing problems for
standard PMKSA caching operations even if OKC is enabled in
wpa_supplicant configuration.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
TDLS responder STA used to retransmit the TDLS Setup Response after 5
seconds if the TDLS Setup Confirm is not received. The initiator would
have enabled the TDLS link and started transmitting the data to the peer
on the TDLS link after transmitting the TDLS Setup Confirm frame. If the
TDLS Setup Confirm frame is not received by the receiver, the
transmissions from the initiator on the direct link would get failed for
the TDLS link not getting enabled on the receiver. This commit reduces
the data delivery failure duration by shortening the retry time of the
TDLS Setup Response frames. The retry limit of the TDLS Response frame
also is increased to ensure that the peer does not miss the frames in
the reduced time period.
Signed-hostap: Sunil Dutt <duttus@codeaurora.org>
The hostapd_cli ess_disassoc command now takes three arguments (STA MAC
address, timeout in ms, URL) and the STA is disconnected after the
specified timeout.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
These events are sent as a special case to both the group interface and
"parent interface" (i.e., the interface that was used for managing P2P
negotiation). The latter is not really correct event, so get rid of it
with the new global control interface design where there is no need to
support legacy upper layer implementations.
Signed-hostap: Jouni Malinen <j@w1.fi>
Replace direct wpa_msg() calls with p2p_dbg(), p2p_info(), and p2p_err()
calls that use a new debug_print() callback to handle actual debug
printing outside the P2P module.
Signed-hostap: Jouni Malinen <j@w1.fi>
This removes wpa_ctrl.h dependency from src/p2p/* and makes the P2P
events more consistent, i.e., everything that is aimed for upper layer
processing from the wpa_supplicant control interfaces is generated in
p2p_supplicant.c.
Signed-hostap: Jouni Malinen <j@w1.fi>
This function can be used instead of wpa_msg() and wpa_msg_ctrl() to
indicate that an event is not specific to a network interface.
Signed-hostap: Jouni Malinen <j@w1.fi>
The wpa_supplicant global control interface parameter can now be used to
explicitly specify an abstract UNIX domain socket (Linux specific
extension) with "@abstract:" prefix and an Android control socket with
"@android:" prefix.
Signed-hostap: Jouni Malinen <j@w1.fi>
Allow invitation exchange to update operating channel selection after
peer channel list has been received similarly to how GO negotiation was
handled.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The new control interface command can be used to send a
BSS Transition Management Query frame to the current AP.
Signed-hostap: Vinayak Kamath <vkamat@codeaurora.org>
The HIST_ENTRY and its variables are allocated within libreadline, so
they won't have the WPA_TRACE special header and cannot be freed with
os_free(). Use free() to avoid issues during wpa_cli termination if any
of the new commands added to the history are to be removed (e.g.,
set_network could include a password).
Signed-hostap: Jouni Malinen <j@w1.fi>
Commit 97279d8d1a started filtering MLME
frame events based on Address 1 (destination) field. This works fine for
frames sent to us, but it did filter out some corner cases where we
actually want to process an event based on a frame sent by us. The main
such case is deauthentication or disassociation triggered by something
external to wpa_supplicant in the system. Fix this by accepting events
for frames where either Address 1 or 2 (transmitter) matches the
interface address.
Signed-hostap: Jouni Malinen <j@w1.fi>
Store context for each tls_init() caller, so events are generated for
the correct wpa_s instance. The tls_global variable is retained for
older OpenSSL implementations that may not have app-data for SSL_CTX.
Signed-hostap: Paul Stewart <pstew@chromium.org>
This patch is based on the original work by Boris Presman and
Victor Goldenshtein. Channel Switch Announcement support has been
removed and event handling as well as channel set handling was
changed, among various other changes.
Cc: Boris Presman <boris.presman@ti.com>
Cc: Victor Goldenshtein <victorg@ti.com>
Signed-hostap: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
This can be used to stop AP mode beaconing temporarily, e.g., in
response to a radar detected event.
This patch is based on the original work by Boris Presman and
Victor Goldenshtein. Channel Switch Announcement support has been
removed and event handling as well as channel set handling was
changed, among various other changes.
Cc: Boris Presman <boris.presman@ti.com>
Cc: Victor Goldenshtein <victorg@ti.com>
Signed-hostap: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
This patch is based on the original work by Boris Presman and
Victor Goldenshtein. Channel Switch Announcement support has been
removed and event handling as well as channel set handling was
changed, among various other changes.
Cc: Boris Presman <boris.presman@ti.com>
Cc: Victor Goldenshtein <victorg@ti.com>
Signed-hostap: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
This patch is based on the original work by Boris Presman and
Victor Goldenshtein. Channel Switch Announcement support has been
removed and event handling as well as channel set handling was
changed, among various other changes.
Cc: Boris Presman <boris.presman@ti.com>
Cc: Victor Goldenshtein <victorg@ti.com>
Signed-hostap: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
This patch is based on the original work by Boris Presman and
Victor Goldenshtein. Channel Switch Announcement support has been
removed and event handling as well as channel set handling was
changed, among various other changes.
Cc: Boris Presman <boris.presman@ti.com>
Cc: Victor Goldenshtein <victorg@ti.com>
Signed-hostap: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
This patch is based on the original work by Boris Presman and
Victor Goldenshtein. Channel Switch Announcement support has been
removed and event handling as well as channel set handling was
changed, among various other changes.
Cc: Boris Presman <boris.presman@ti.com>
Cc: Victor Goldenshtein <victorg@ti.com>
Signed-hostap: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
DFS implementation requires to run an eventloop while monitoring
the Channel Availability Check (CAC). After that, the "real" event
loop is started, and should not fail doing so.
Signed-hostap: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
The reason code for the teardown request is overwritten for open
mode. This commit removes the code that does so by reverting parts
of commit 0cb12963b6.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The use of AID=1 for the nl80211 dummy STA case is specific to the
driver (cfg80211), so better move this into the driver wrapper instead
of generic TDLS implementation.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The information of the peer's AID is required for the driver to
construct partial AID in VHT PPDU's. Pass this information to the driver
during add/set station operations (well, as soon as the information is
available, i.e., with set station operation currently).
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
currbuf_valid needs to be cleared when an old command from history is
processed to avoid leaving a bogus entry that makes history_prev() skip
the last entry in history.
Signed-hostap: Jouni Malinen <j@w1.fi>
This is a C compiler extension and not needed, so replace with standard
compliant way of calculating the pointer.
Signed-hostap: Jouni Malinen <j@w1.fi>
This reverts commit df2f9ec6b2.
The current AOSP snapshot for JB includes nla_put_u32(), so this is not
needed anymore and is also causing linking issues due to duplicated
definition.
Signed-hostap: Jouni Malinen <j@w1.fi>
Since "pairwise" is defined as an integer, the current assignment leads
to it having the value 0 or 8, which is a bit strange in debug output:
WPA: Send EAPOL(version=2 secure=1 mic=1 ack=1 install=1 pairwise=8
kde_len=46 keyidx=2 encr=1)
Use !!(...) to normalize it to 0 or 1.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
For some testing it can be useful to force the Key MIC in group
EAPOL-Key frames to be corrupt. Add an option to allow setting a
probability for corrupting the Key MIC and use it in the WPA code,
increasing the first byte of the MIC by one to corrupt it if desired.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
In case that NL80211_PROTOCOL_FEATURE_SPLIT_WIPHY_DUMP is supported,
wiphy_info_handler() is called several times, where
NL80211_ATTR_MAX_REMAIN_ON_CHANNEL_DURATION is present only in one
of these calls. Thus capa->max_remain_on_chan is overridden in
all other calls.
Fix it so the default value is set only after all the wiphy info was
received.
Signed-hostap: Ilan Peer <ilan.peer@intel.com>
nl80211 has obsoleted WEXT as the preferred kernel interface for
controlling wireless drivers. Update wpa_supplicant driver interface
list order so that nl80211 gets used first if both nl80211 and wext
interfaces are included in the build. In addition, update README to
reflect the fact that WEXT is obsolete.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
"WPS_ER_START ifname=<interace>" can now be used to force a specific
interface to be used for UPnP operations. This is especially useful for
automated test cases where the lo interface can now be used easily to
perform ER operations.
Signed-hostap: Jouni Malinen <j@w1.fi>
There are quite a few places in the current implementation where a nul
terminated string is generated from binary data. Add a helper function
to simplify the code a bit.
Signed-hostap: Jouni Malinen <j@w1.fi>
My APs generate their configuration on their own using a different
number of (vlan-enabled) bss. Currently, all my vlan_file files consist
of a single line: the wildcard line. Configuration file generation would
be easier, if the hostapd configuration file would not depend on those
simple vlan_file files.
This patch removes the need for those one-line files by using the
<device>.<vlan> naming scheme if no vlan_file is given (or that file is
empty). This should not break any existing setup, as using dynamic_vlan
with no vlan configured does not make sense anyway.
Signed-hostap: Michael Braun <michael-dev@fami-braun.de>
When a specific out-of-band Device Password is enabled, it can be useful
to be able to advertise that in the selected registrar information.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
All P2P use cases are required to use the global operating table and
there is no need to need to try to maintain some backwards compatibility
with country code -specific values. Clean up the implementation by
removing the unnecessary country parameter.
Signed-hostap: Jouni Malinen <j@w1.fi>
Reset ft_completed if STA receives deauthentication
between FT reassoc success and the subsequent initial
mobility authentication and association.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Commit fb8984fd6f added a mechanism to
skip the Listen state when the peer is expected to be waiting for us to
initiate a new GO Negotiation. However, this flag was set when building
the GO Negotiation Response frame with status 1 regardless of whether we
managed to send that frame or peer receive it. This could result in GO
Negotiation failures in cases where the peer did not receive the
response and Listen channels of the devices were different. Fix this by
setting the flag only after TX status indicating success has been
received.
This fixes frequent failures shown for the test_grpform_pbc hwsim test
case.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
We should not call getSessionID method if it's not provided. This fixes
a regression from commit 950c563076 where
EAP methods that did not implement getSessionId resulted in NULL pointer
dereference when deriving the key.
Signed-off-by: Shijie Zhang <shijiez@qca.qualcomm.com>
When Action frame TX is postponed until a pending p2p_scan completes,
there may be additional operations that need to be continued after the
postponed Action frame TX operation completes. Fix this by starting
pending operation (if any) from TX status event for after_scan_tx
frames.
This fixes common errors seen with the test_discovery hwsim test case.
Signed-hostap: Jouni Malinen <j@w1.fi>
Add "EAPLogoff" and "EAPLogon" interface DBus commands which
parallel the "logoff" and "logon" wpa_ctrl commands which terminate
and restart EAP authentication. Slightly enhance the "logon" case
by expiring any running "startWhile" timer.
Signed-hostap: Paul Stewart <pstew@chromium.org>
In order to test clients in scenarios where APs may (randomly)
drop certain management frames, introduce some testing options
into the hostapd configuration that can make it ignore certain
frames. For now, these are probe requests, authentication and
(re)association frames.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
This option can be used only for global parameters that are not going
to be changed from settings.
Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
Signed-off-by: Iliyan Malchev <malchev@google.com>
Dmitry reported that the kernel could no longer parse the
scheduled scan attributes correctly after my patch to use
nla_nest_start/nla_nest_end. The reason is that the wrong
attribute is closed I accidentally made it close the full
scan config instead of just the SSID match set.
Reported-by: Dmitry Shmidt <dimitrysh@google.com>
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
Harmonize EAP status events over control interface to provide same
functionality as existing D-Bus callback.
Signed-hostap: Chris Hessing <chris.hessing@cloudpath.net>
A kernel commit ("mac80211: fix FT roaming") started validating that the
STA entry is marked associated when adding a key. While this is needed
to fix some FT use cases with hardware crypto, it has a side effect of
breaking TDLS key configuration. Work around this by trying to
re-configure the key for the direct link after the STA entry has been
set with all information. In addition, try to tear down the link if
anything goes wrong in key configuration (if both attempts fail) or
enabling the link in the driver.
Signed-hostap: Jouni Malinen <j@w1.fi>
"WPS_NFC_CONFIG_TOKEN <WPS/NDEF> <network id>" can now be used to build
an NFC configuration token from a locally configured network.
Signed-hostap: Jouni Malinen <j@w1.fi>
This extends the WPS ER commands that previously accepted only UUID as
an identifier for an AP to use either UUID or BSSID for this.
Signed-hostap: Jouni Malinen <j@w1.fi>
wps_build_public_key() takes the dh_ctx into use and another attempt to
use the same DH keys fails with wps->dh_ctx being set to NULL. Avoid
this by using the DH parameters only if dh_ctx is valid. This fixes
cases where a use of local pre-configured DH keys followed by an
operating using peer DH keys would faild due to unexpected attempt to
use local keys again.
Signed-hostap: Jouni Malinen <j@w1.fi>
Some extended capabilities (I'm currently interested in "Operating Mode
Notification" for VHT) are implemented by the kernel driver and exported
in nl80211. Use these in hostapd/wpa_supplicant.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
The new wps_independent=1 configuration parameter can be used to remove
interfaces from the shared hostapd process WPS control (i.e., to apply
WPS operations only to a subset of interfaces instead of all).
Signed-hostap: Jouni Malinen <j@w1.fi>
This allows WPS to update AP configuration in the case no hostapd
configuration file is used (i.e., dynamic configuration through the
control interface).
Signed-hostap: Jouni Malinen <j@w1.fi>
Instead of allocating a new message and then moving that into
the message being built, use nla_nest_start() and put the data
into the message directly.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
As per P2P specification v1.2: "The P2P Group Info attribute shall be
omitted if there are zero connected P2P Clients."
Do not add the attribute if there are not connected peers.
Signed-hostap: Chaitanya T K <chaitanya.mgit@gmail.com>
When the OS is out of random bytes in SM_STATE(WPA_PTK, AUTHENTICATION2)
in ap/wpa_auth.c, hostapd sends the sm to state DISCONNECT without
clearing ReAuthenticationRequest, resulting in an infinite loop.
Clearing sm->ReAuthenticationRequest using gdb fixes the running hostapd
instance for me. Also sm->Disconnect = TRUE should be used instead of
wpa_sta_disconnect() to make sure that the incomplete ANonce does not
get used.
Fix this issue by resetting sm->ReAuthenticationRequest even if the STA
gets disconnected and use sm->Disconnect instead of
wpa_sta_disconnect().
Signed-hostap: Michael Braun <michael-dev@fami-braun.de>
A non-HT capable AP on any channel could have triggered us to enable
protection regardless of own operating channel if the driver delivered
Beacon frames from other channels. The channel detection in ap_list is
not exactly ideal, but most cases can be handled by checking ap->channel
against the currently configured channel (or secondary channel in case
of HT40).
Signed-hostap: Jouni Malinen <j@w1.fi>
This iter_next/iter_prev pointers were not really used for anything, so
get rid of the unnecessary complexity in the AP list maintenance.
Signed-hostap: Jouni Malinen <j@w1.fi>
Commit 6b56cc2d97 added a possible call to
p2p_reset_pending_pd() prior to checking config_methods match between
our request and peer response. That reset call could clear
dev->req_config_methods and as such, result in unexpected
P2P-PROV-DISC-FAILURE report here even in cases where the peer accepts
the provision discovery. Fix this by using a local copy of the
req_config_methods variable.
Signed-hostap: Jouni Malinen <j@w1.fi>
The new -G<group> command line argument can now be used to set the group
for the control interfaces to enable cases where hostapd is used without
a configuration file and the controlling program is not running with
root user privileges.
Signed-hostap: Jouni Malinen <j@w1.fi>
Enhance TDLS Setup Request processing to support both external and
internal TDLS setup for the case where concurrent TDLS initialization
results in the TDLS Setup Request from the peer getting accepted.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
wpa_tdls_peer_free() ended up getting called after some of the
parameters from the TDLS Setup Request frame were copied into the struct
wpa_tdls_peer information. This could result in continuing with cleared
information in case the new exchange was the one that is used in
concurrent initialization case or if this is to re-negotiated an
existing TDLS link. The driver would not be provided with all the peer
capabilities correctly in such case.
Fix this by moving the existing_peer check to happen before the
information from the TDLS Setup Request frame is copied.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
If we accept the peer TPK M1 after having sent our TPK M1, we need to
reject TPK M2 from the peer to avoid going through two TDLS setup
exchanges.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
In some cases where the ack for Invitation response is lost,
the device is stuck in invited state but the peer device starts
GO. In line with the implementation of Negotiation Confirm,
assume invitation response was actually received by the peer
even though ack was not reported.
Signed-hostap: Vivek Natarajan <nataraja@qca.qualcomm.com>
Commit b52f084cfa introduced a mechanism
for adding arbitrary vendor-specific elements into the Beacon and Probe
Response frames. However, this information was not added to the separate
buffers used for specifying Beacon and Probe Response IEs for drivers
that build the frames internally. Add vendor_elements to these values,
too, to support such drivers in addition to drivers that use the full
Beacon tail/head buffers.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
When the wiphy information is split, there's no guarantee that the
channels are processed before the bitrates; in fact, with the current
kernel it happens the other way around. Therefore, the mode information
isn't set up correctly and there's no 11g mode.
Fix this by doing the 11b/11g determination as part of the
postprocessing.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
Previously, P2P_PD_DURING_FIND state was scheduled for 200 ms and the
P2P state was not change until that timeout regardless of whether the PD
Response for recieved or not. There is no need to wait for that timeout
if the response is received, so allow the next operation to be performed
immediately after the response has been processed.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This makes it easier to understand how scan operations and events occur
when multiple interfaces is being controlled by a single wpa_supplicant
process.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Add a driver capability flag for drivers which support IBSS mode and set
it for nl80211 drivers which have set the NL80211_IFTYPE_ADHOC.
Add a new option "modes" to "get_capability" which will return "AP" and
"IBSS" if the corresponding capability flags are set.
The idea is that this can be used for UIs to find out if the driver
supports IBSS mode.
Signed-hostap: Bruno Randolf <br1@einfach.org>
Clear WLAN_STA_ASSOC_REQ_OK, otherwise no Class 3 frame will be sent to
the disconnected STA in response to data frames.
Signed-hostap: Felix Fietkau <nbd@openwrt.org>
If a peer replies to persistent group invitation with status code 8
(unknown group), remove the peer from the p2p_client_list if we are the
GO or remove the persistent group if we are the P2P client since it
looks like that the peer has dropped persistent group credentials and
the provisioning step needs to be executed again.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Commit 50285f5ca8 changed number of rules
in channel selection and among other things, it broke the design where
the currently used operating channel on a virtual interface that is
shared by the same radio is preferred to avoid costs related to
multi-channel concurrency. Fix this regression by making the P2P module
aware of the shared channel and using that preference as the highest
priority when re-selecting the channel during negotiation.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Commit 50285f5ca8 ended up forcing channel
re-selection in number of cases where the peer would actually have
accepted our initial preference. Fix the parts related to best channel
information by using best_freq_overall as the highest priority and by
skipping the band changes if the peer supports the channel that we
picked since these were based on the assumption that
p2p_reselect_channel() is called only if the peer could not accept our
initial choice which is not the case anymore.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
If the previously started setup is terminated in case both peers
initiate TDLS link at more or less the same time, disable the old link
to allow the dummy station entry to be deleted from cfg80211 so that a
new entry can be added for the setup direction that will be allowed to
proceed.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Add NL80211_CMD_UPDATE_FT_IES to support update of FT IEs to the
WLAN driver. Add NL80211_CMD_FT_EVENT to send FT event from the
WLAN driver. This will carry the target AP's MAC address along
with the relevant Information Elements. This event is used to
report received FT IEs (MDIE, FTIE, RSN IE, TIE, RICIE).
Signed-off-by: Deepthi Gowri <deepthi@codeaurora.org>
It is possible for a P2P client to connect to an operating group without
exchanging any Probe Request/Response frames that would allow the GO to
discover the peer. To make sure there is a P2P peer entry at the GO, try
to add the peer information based on P2P IE in (Re)Association Request
frame.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Add support for VHT capability overrides to allow testing connections
with a subset of the VHT capabilities that are actually supported by
the device. The only thing that isn't currently supported (by mac80211
and this code) is the RX/TX highest rate field.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
This implements support for the new NL80211_ATTR_SPLIT_WIPHY_DUMP in
nl80211 to handle wiphy information that cannot fit in one message.
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-hostap: Dennis H Jensen <dennis.h.jensen@siemens.com>
The peer commit element needs to be validated to pass one of the steps
listed in IEEE 802.11, 11.3.5.4:
scalar-op(r, ELEMENT) = 1 modulo p
Similar step was present for ECC groups, but was missing for FFC groups.
This is needed to avoid dictionary attacks.
Thanks to Michael Roßberg and Sascha Grau for reporting this.
Signed-hostap: Jouni Malinen <j@w1.fi>
It is clearer to keep all the validation steps described in IEEE 802.11
11.3.5.4 in a single location instead of splitting this between the
parsing and processing functions.
Signed-hostap: Jouni Malinen <j@w1.fi>
Peer device includes its list of allowed operating channels in the
Invitation Response frame. When we are becoming the GO, use that list
from the peer to filter out acceptable channels to avoid selecting a
channel that the peer is unable to use.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
When re-invoking a persistent group in P2P client role, the new
pref=<MHz> parameter can now be used with the p2p_invite command to
indicate a preferred operating frequency. Unlike the older freq=<MHz>
parameter, this leaves GO an option to select another channel (from our
supported channels) if the GO cannot accept the channel.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
If multi channel concurrency is supported, we have to populate the
p2p_channels with list of channels that we support. Use the same design
that was previously added for GO Negotiation.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The VHT IE struct just has an opaque 8-byte array for the MCS
set, make it more expressive by explicitly naming the pieces.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
Commit fb8984fd6f cleared wps_method to
WPS_NOT_READY in p2p_stop_find_for_freq() as an attempt to clear
authorization when a group formation is cancelled. However, this code
path is hit also in cases where the user did not actually cancel
anything (e.g., from p2p_process_go_neg_req()). As such, it is not fine
to clear wps_method here even if it could be proper for some cases. For
now, revert that part to avoid regressions and consider clearing
wps_method on cancel separately.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
In case we have replied to a peer's GO Negotiation Request frame with a
GO Negotiation Response frame using status code
info-currently-unavailable (1), the peer is likely going to wait for us
to initiate GO Negotiation on its Listen channel. We were previously
using alternativing send-GO-Neg-Req and Listen phase when providing that
response after the user had authorized the connection. However, the
Listen phase here is unnecessary in this case and will make the
connection take longer time to go through. Skip the Listen phase and
make the wait-for-GO-Neg-Resp timeout random between 100 and 200 ms to
avoid getting in sync with the peer. In practice, this will make us
retry GO Negotiation Request frames more frequently and remain on the
peer's Listen channel for most of the time when initiating GO
Negotiation after status=1 response.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
There may be environments in which large number of devices are operating
on the social channels. In such cases, it is possible for the Action
frame TX operation wait for quite long time before being able to get the
frame out. To avoid triggering GO Negotiation failures, increase the
timeouts for GO Neg Req (with TX ACK) and GO Neg Resp (with or without
TX ACK as long as status=0) to 500 ms.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This flag will add ==== delimiter between to separate bss results.
Unlike the other BSS command MASK values, this delimiter is not
included by default to avoid issues with existing users of the BSS
command.
Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
It is possible for the driver to indicate multiple Probe Request frames
that would be processed in a single loop. If those frames happen to be
from a peer which with we are trying to start GO Negotiation, multiple
timeouts to start GO Negotiation (p2p_go_neg_start) could end up being
scheduled. This would result in confusing burst of multiple GO
Negotiation Request frames being sent once the RX loop finally
concludes. Avoid this by scheduling only a single eloop timeout to
trigger GO Negotiation regardless of how many Probe Request frames from
the peer is received. In addition, make sure this timeout gets canceled
in p2p_deinit().
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
If we have already sent out GO Negotiation Response and are waiting for
the peer to reply with GO Negotiation Confirm, there is no point in
re-starting GO Negotiation based on Probe Request frame from the peer.
Doing that would just result in confusing GO Negotiation exchange with
multiple sessions running at the same time.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The device that is selected as the GO shall incode P2P Group ID
attribute in GO Negotiation Response/Confirm message. Previously we did
not reject a message without that attribute since it was possible to
continue operations even without knowing the SSID. However, this can
potentially result in confusing results since missing P2P Group ID
attribute can be a sign of conflicting GO role determination (both
devices assuming the peer is the GO). To get clearer end result for the
GO Negotiation, reject this as a fatal error. In addition, stop GO
Negotiation if GO Negotiation Confirm indicates non-zero status since
that is also a fatal error.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Commit 624b4d5a64 changed GO Negotiation
to use the same Dialog Token value for all retransmissions of the GO
Negotiation Request within the same session. However, it did leave the
tie breaker bit changing for each frame. While this should not have
caused issues for most cases, it looks like there are possible sequences
where the peer may end up replying to two GO Negotiation Request frames
with different tie breaker values. If in such a case the different GO
Negotiation Response frames are used at each device, GO role
determination may result in conflicting results when same GO intent is
used.
Fix this by assigning the tie breaker value at the same time with the
dialog token (i.e., when processing the p2p_connect command instead of
for each transmitted GO Negotiation Request frame) to avoid issues with
GO selection.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The information of the peer's VHT capability is required for the
driver to establish a TDLS link in VHT mode with a compatible peer.
Pass this information to the driver when the peer station is
getting added.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
WSC specification 2.0 section 7.4 describes OOB password to be expressed
in ASCII format (upper case hexdump) instead of raw binary.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Commit 2d9ffe1e85 broke GAS server
callback for receiving Public Action frames. The incorrect context
pointer was used in the public_action_cb2 case. Fix this to use the
correct context pointer.
Signed-hostap: Jouni Malinen <j@w1.fi>
Hostapd provides QoS info of the STA (Service Period & AC mask) to the
kernel during wpa_driver_nl80211_sta_add call. Bit 5 and Bit 6 of QoS
info represents the Max SP length. Fix an issue in the code to fetch the
Max SP by shifting right the QoS info by value WMM_QOSINFO_STA_SP_SHIFT.
(operator ">" is replaced with ">>" operator).
Signed-off-by: Srinivasan <srinivasanb@posedge.com>
"WPS_NFC_TOKEN <WPS/NDEF>" used to generate a new NFC password token
regardless of whether there was a pre-configured token in the
configuration. Change this to use the pre-configured value, if
available, instead. This allows the same command to be used to write the
password token to an NFC tag more conveniently.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The contents of the peer's capability and extended capability
information is required for the driver to perform TDLS P-UAPSD and Off
Channel operations. Pass this information to the driver when the peer
station is getting added.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The information of the peer's HT capability and the QOS information is
required for the driver to perform TDLS operations. Pass this
information to the driver when the peer station is getting added.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Registrar is allowed to propose another Device Password ID in M2. Make
Enrollee validate Device Password ID in M2 to check if this happened.
This commit adds support for changing from NFC password token to default
PIN for the case where the AP is the Enrollee and has both the NFC
password token and AP PIN enabled at the same time.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Commit ffdaa05a6b added support for using
NFC password token from an AP. However, it had a bug that prevented the
wpa_supplicant wps_reg command from being used with "nfc-pw" as the PIN
value. Fix string comparison to handle this correctly.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
A TDLS Teardown frame with Reason Code 3 (Deauthenticated because
sending STA is leaving (or has left) IBSS or ESS) shall be transmitted
to all TDLS peer STAs (via the AP or via the direct path) prior to
transmitting a Disassociation frame or a Deauthentication frame to the
AP.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The driver may have cached (e.g., in cfg80211 BSS table) the scan
results for relatively long time. To avoid reporting stale information,
update P2P peers only based on results that have based on frames
received after the last p2p_find operation was started.
This helps especially in detecting when a previously operating GO stops
the group since the BSS entry for that could live for 30 seconds in the
cfg80211 cache. Running p2p_flush followed by p2p_find will now allow
wpa_supplicant to not add a P2P peer entry for that GO if the group had
been terminated just before that p2p_flush command. Previously, that GO
could have been indicated as a newly found device for up to 30 seconds
after it had stopped the group.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
For various P2P use cases, it is useful to have more accurate timestamp
for the peer information update. This commit improves scan result
handling by using a single timestamp that is taken immediately after
fetching the results from the driver and then using that value to
calculate the time when the driver last updated the BSS entry. In
addition, more debug information is added for P2P peer updates to be
able to clearly see how old information is being used here.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
If we discover a P2P peer based on a Beacon frame from the GO role, we
do not get information about the supported configuration methods. This
can result in issues if the P2P managing entity above wpa_supplicant is
not prepared to handling config_methods=0x0. To avoid this, postpone
reporting of the P2P-DEVICE-FOUND event when this happens on one of the
social channels. It would be good to be able to this on all channels,
but that could result in issues of never indicating the event for a peer
that is operating a GO on a channel that requires passive scanning.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
It could be possible for the scan results to include two entries for a
peer, one from the Listen state and the second one from the GO role. The
latter could be based on a Beason frame. If that happens and the entry
from GO is processed last, the P2P peer config_methods value could
potentially get cleared since Beacon frames do not include this
information in either WPS or P2P element. Avoid this by allowing the
config_methods value for P2P peers to be updated only if the new value
is non-zero.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Since there could be multiple carrier records, it is cleaner to build
only the WPS carrier record instead of full NFC connection handover
request within wpa_supplicant.
Signed-hostap: Jouni Malinen <j@w1.fi>
Control interface command "NFC_GET_HANDOVER_SEL NDEF WPS-CR" can now be
used to fetch WPS carrier record from hostapd.
Signed-hostap: Jouni Malinen <j@w1.fi>
The capability itself isn't really affected by an OBSS
scan, only the HT operation must then be restricted to
20 MHz. Change this, and therefore use the secondary
channel configuration to determine the setting of the
OP_MODE_20MHZ_HT_STA_ASSOCED flag.
This shouldn't really change anything functionally,
it just makes the code a little less confusing and
is also needed to implement more dynamic bandwidth
changes if ever desired.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
This adds a new getSessionId() callback for EAP peer methods to allow
EAP Session-Id to be derived. This commits implements this for EAP-FAST,
EAP-GPSK, EAP-IKEv2, EAP-PEAP, EAP-TLS, and EAP-TTLS.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
In addition to the offload mechanism, the Android configuration and
makefiles are extended to allow this to be configured for the build by
dropping in platform specific configuration files and makefile without
having to modify any existing files.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
ANDROID_SETGROUPS_OVERRIDE macro can now be used to override setgroups()
values based on build configuration.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
When pending p2p_find fails we need to send p2p_stop_find event to
indicate the previous p2p_find command has been processed.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Commit 1a9f6509b3 added support for
fragmenting the P2P IE in Probe Response frames from a GO. However, it
did not take into account the possibility of Wi-Fi Display IE being
included in the same buffer and caused a regression for the cases where
Wi-Fi Display is enabled. Fix this by building the possibly fragmented
P2P IE first and then concatenating the separate IEs together.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
On the DMG (60 GHz) band, capability bits defined differently from
non-DMG ones. Adjust capability matching to cover both cases.
Also, for non-DMG bands, check ESS bit is set.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
When AP mode operation reject the client, nl80211 layer advertises the
connect failed event with the reason for failures (for example, max
client reached, etc.) using NL80211_CMD_CONN_FAILED.
This patch adds some debug messages whenever such an event is received
from the nl80211 layer and also the same event is posted to the upper
layer via wpa_msg().
Signed-off-by: Raja Mani <rmani@qca.qualcomm.com>
The reason code used for calculating the MIC should correspond to the
reason code with which the teardown frame is sent, as the receiver shall
use the one obtained in the frame for validating the MIC.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
If an implicit TDLS set up request is obtained on an existing link or an
to be established link, the previous link was not removed. This commit
disables the existing link on a new set up request. Also,
wpa_tdls_reneg() function was invoking wpa_tdls_start() on an already
existing peer for the case of internal setup, which is incorrect. Thus
the invocation of wpa_tdls_start() is removed in wpa_tdls_reneg() and
also this function is renamed to wps_tdls_remove() as it does not
renegotiation rather shall remove the link (if any) for the case of
external setup.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
There is no need to have this check copied to each caller since this
needs to be done for every case when a new peer is being added.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Peer entries were getting added on every discover request from the peer,
thus resulting in multiple entries with the same MAC address. Ensures
that a check is done for the presence of the peer entry and reuse the
existing entry instead of adding a new one.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
GAS server used the same public_action_cb mechanism as P2P to process
Action frames. This ended up overriding P2P processing of Action frames
while running an AP/GO interface with a build that enables Interworking
(e.g., for Hotspot 2.0) and a driver that uses hostapd for AP mode
SME/MLME. Fix this by adding a separate callback registration for the
GAS server. This should really be cleaned up by supporting arbitrary
number of callback handlers, but for now, this addresses the regression
with a minimal change.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Very basic support for OpenBSD. No support for scanning yet, so this needs
ap_scan=0 and expects that the user has configured the interface manually
using ifconfig(8).
Signed-hostap: Mark Kettenis <kettenis@openbsd.org>
Commit 6aaac006af modified the
pmksa_cache_init() prototype, but forgot to update the empty wrapper
function which is used when PMKSA caching is not included in the build.
Signed-hostap: Jouni Malinen <j@w1.fi>
When scan failed, the wpa_driver_nl80211_scan method tried
to recursively call itself, but it passed in the wrong argument
for the void*, and so then it crashed accessing bad memory.
With this fix, hostapd still will not retry the scan later, but
at least it will exit cleanly and won't polute the file system
with core files.
Signed-off-by: Ben Greear <greearb@candelatech.com>
The P2P-FIND-STOPPED event was sent only in the P2P_SEARCH state, but
this needs to be send also in the new continue-search-when-ready states
P2P_CONTINUE_SEARCH_WHEN_READY and P2P_SEARCH_WHEN_READY for consistent
behavior.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Signal the start of EAP authentication as well as when additional
credentials are required to complete.
Signed-hostap: Paul Stewart <pstew@chromium.org>
This was previously included only with NL80211_CMD_ASSOCIATE, but the
information is as useful (if not even more useful) for
NL80211_CMD_CONNECT. It should be noted that cfg80211 does not yet use
this attribute with NL80211_CMD_CONNECT, but that can be added easily.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Each GO Negotiation Request is (re)tried with an unique dialog token and
a GO Negotiation Response / Confirmation from the peer with a mismatched
dialog token is ignored which could result in a failure in this group
formation attempt. Thus, the P2P device would continue retrying the GO
Negotiation Request frames till the GO Negotiation Response frame with a
matching dialog token is received. To avoid the failures due to the
dialog token mismatch in retry cases if the peer is too slow to reply
within the timeout, the same dialog token value is used for every retry
in the same group formation handshake.
It should be noted that this can result in different contents of the GO
Negotiation Request frame being sent with the same dialog token value
since the tie breaker bit in GO Intent is still toggled for each
attempt. The specification is not very clear on what would be the
correct behavior here. Tie breaker bit is not updated on
"retransmissions", but that is more likely referring to the layer 2
retransmission and not the retry at higher layer using a new MMPDU.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This allows even more memory to be freed when the SAE instance enters
Accepted state. This leaves only the minimal needed memory allocated
during the association which is especially helpful for the AP
implementation where multiple stations may be associated concurrently.
Signed-hostap: Jouni Malinen <j@w1.fi>
Most of the variables are not needed anymore once the SAE instance
has entered Accepted state. Free these to save memory.
Signed-hostap: Jouni Malinen <j@w1.fi>
The rand/mask values and commit scalar are derived using the exact same
operations, so only use a separate function for deriving the commit
element.
Signed-hostap: Jouni Malinen <j@w1.fi>
There is no need to postpone this validation step to a separate
processing operation for the commit message, so move the minimal
validation tasks into the parsing functions.
Signed-hostap: Jouni Malinen <j@w1.fi>
Move the bignum comparison part into the bignum library to allow a
single implementation of rand generation for both ECC and FCC based
groups.
Signed-hostap: Jouni Malinen <j@w1.fi>
The groups 22, 23, and 24 are not based on a safe prime and generate a
prime order subgroup. As such, struct dh_group is also extended to
include the order for previously defined groups (q=(p-1)/2 since these
were based on a safe prime).
Signed-hostap: Jouni Malinen <j@w1.fi>
This allows FFC groups to be used with SAE. Though, these groups are not
included in the default sae_groups value based on what is available
since the FFC groups have the additional requirement of using a safe
prime with the current implementation (or specification of the group
order).
Signed-hostap: Jouni Malinen <j@w1.fi>
The optional "reason=<reason code>" parameter to the ctrl_iface
deauthenticate and disassociate commands can now be used to change the
reason code used in the disconnection frame. This can be used, e.g., by
P2P GO to disconnect a single P2P client from the group by sending it an
indication of the group getting terminated (Deauthentication frame with
reason code 3). It needs to be noted that the peer device is still in
possession on the PSK, so it can still reconnect to the group after this
if it does not follow the group termination indication.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This commit increases the maximum buffer size for P2P Client Info
advertized by the Group Owner in the Probe Response frames.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Use of two variables to track bounds checking seems to be a bit too much
for some static analyzers, so add an extra condition for buffer padding
to avoid incorrect warnings.
Signed-hostap: Jouni Malinen <j@w1.fi>
These verify that a proper pointer type is used and in addition, seems
to get rid of some false static analyzer warnings.
Signed-hostap: Jouni Malinen <j@w1.fi>
The code initializing GMK Counter uses the group pointer value as extra
entropy and to distinguish different group instances. Some static
analyzers complain about the sizeof(pointer) with memcpy, so use a more
explicit type casting to make it more obvious what the code is doing.
Signed-hostap: Jouni Malinen <j@w1.fi>
hostapd.conf sae_groups parameter can now be used to limit the set of
groups that the AP allows for SAE. Similarly, sae_groups parameter is
wpa_supplicant.conf can be used to set the preferred order of groups. By
default, all implemented groups are enabled.
Signed-hostap: Jouni Malinen <j@w1.fi>
In addition to the trivial change in adding the new group ientifier,
this required changes to KDF and random number generation to support
cases where the length of the prime in bits is not a multiple of eight.
The binary presentation of the value needs to be shifted so that the
unused most significant bits are the zero padding rather than the extra
bits in the end of the array.
Signed-hostap: Jouni Malinen <j@w1.fi>
In addition to the mandatory group 19 (256-bit random ECP group) add
support for groups 20 (384-bit), 25 (192-bit), and 26 (224-bit).
Signed-hostap: Jouni Malinen <j@w1.fi>
The counter>200 check needs to be done before the continue-on-not-found
case to be effective in stopping this loop.
Signed-hostap: Jouni Malinen <j@w1.fi>
The buffer is set based on maximum group prime length, but pwd-value
needs to be correct length for the negotiated group.
Signed-hostap: Jouni Malinen <j@w1.fi>
This makes the SAE implementation a bit simpler by not having to build
the bignum for group order during execution.
Signed-hostap: Jouni Malinen <j@w1.fi>
hostapd can now be configured to use anti-clogging mechanism based on
the new sae_anti_clogging_threshold parameter (which is
dot11RSNASAEAntiCloggingThreshold in the standard). The token is
generated using a temporary key and the peer station's MAC address.
wpa_supplicant will re-try SAE authentication with the token included if
commit message is rejected with a token request.
Signed-hostap: Jouni Malinen <j@w1.fi>
IEEE Std 802.11-2012, 11.3.8.6.1: If there is a protocol instance for
the peer and it is in Authenticated state, the new Commit Message
shall be dropped if the peer-scalar is identical to the one used in
the existing protocol instance.
Signed-hostap: Jouni Malinen <j@w1.fi>
The enum values for struct sae_data::state now match the protocol
instance states as defined in IEEE Std 802.11-2012, 11.3.8.2.2
Signed-hostap: Jouni Malinen <j@w1.fi>
Even if the PAC file does not start with the proper header line, allow
the file to be used if it is empty. [Bug 423]
Signed-hostap: Jouni Malinen <j@w1.fi>
The PMKSA cache expiration timer was not actually ever initialized since
the only place for registering the timeout was in the timeout handler.
Fix this by initializing the timer whenever a new PMKSA cache entry is
added to the beginning of the list (i.e., when it was the first entry or
expires before the entry that was previously going to expire first).
[Bug 393]
Signed-hostap: Jouni Malinen <j@w1.fi>
Commit 4378fc14eb started using QoS Data
frames for QoS STAs. It used the correct flags value for WPA/RSN
EAPOL-Key frames, but wrong flags for IEEE 802.1X EAPOL frames. The
WPA_STA_WMM value used in driver_nl80211.c happens to be identical to
WLAN_STA_ASSOC in sta->flags and this makes driver_nl80211.c try to use
QoS header for all STAs. Fix this by properly converting the flags from
WLAN_STA_* to WPA_STA_*. [Bug 426]
Signed-hostap: Jouni Malinen <j@w1.fi>
Commit 68a41bbb44 broke fallback from
reauth id to fullauth id by not allowing a second AKA/Identity round to
be used after having received unrecognized reauth_id in the first round.
Fix this by allowing fullauth id to be requested in such a case.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Commit 175171ac6c ensured that the PD
requests are retried in join-a-running group case and the Enrollee is
started on either receiving the PD response or after the retries. Each
PD request is retried with an unique dialog token and a PD response from
the GO with a mismatched dialog token is ignored. Thus, the P2P client
would continue retrying the PD requests till the response with a
matching dialog token is obtained. This would result in the GO getting
multiple PD requests and a corresponding user notification (POP UP) in
implementations where each PD request results in a POP UP, resulting in
a bad user experience. To avoid such behavior, the same dialog token
value is used for every retry in the same PD exchange.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
wpa_driver_nl80211_ap() returned error if set_freq failed, but left the
previously set nlmode to GO/AP. While this should not be issue for most
purposes, it leaves the interface in somewhat unexpected state and could
potentially affect operations prior to next connection attempt. Address
this by restoring the previous nlmode if AP mode cannot be started for
some reason.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This makes it easier to read the code for the two possible cases
(forced/preferred channel and automatic channel selection).
Signed-hostap: Jouni Malinen <j@w1.fi>
Since the operating channel is randomly set to 1/6/11 on init, which is
commonly included in the channel intersection, we were effectively
ignoring the set of P2P preferred channels when trying to improve
channel selection after having received peer information. Fix this by
trying to get the best channel we can, unless the user hard coded the
operating channel in the configuration file or p2p_connect command. Fall
back to the initial randomly selected channel if a better one cannot be
chosen.
Signed-hostap: Arik Nemtsov <arik@wizery.com>
Even if the peer does not accept the forced channel, we should not allow
the forced_freq parameter to be be overridden, i.e., such a case needs
to result in GO Negotiation failure.
Signed-hostap: Jouni Malinen <j@w1.fi>
Both p2p_connect and p2p_authorize use the same functionality to select
the channel preferences for GO Negotiation. The part of setting this
device flag was copied to each function, but it can also be handled by
the shared function after some reordering of code.
Signed-hostap: Jouni Malinen <j@w1.fi>
The exact same mechanism was used for determining the operating channel
at the device that becomes the GO regardless of whether this was
triggered by reception of GO Negotiation Request of Response frame. Use
a shared function to avoid duplicated implementation and potential
differences in the future.
Signed-hostap: Jouni Malinen <j@w1.fi>
When no other user preference is specified, opt to use an operating
channel that allows HT40 operation. This way, if driver capabilities
and regulatory constraints allow, we might enjoy increased bandwidth.
Signed-hostap: Arik Nemtsov <arik@wizery.com>
cfg80211 caches the scan results according the channel number. Due to
the 15 sec aging this might cause the user mode to see more than one
scan result with the same BSSID, e.g. - one scan result for the
P2P Device and one for the P2P GO (once it's enabled).
Fix this by updating the device entry only if the new peer entry is
newer than the one previously stored.
Signed-off-by: Yoni Divinsky <yoni.divinsky@ti.com>
Signed-off-by: Victor Goldenshtein <victorg@ti.com>
Signed-off-by: Igal Chernobelsky <igalc@ti.com>
Signed-hostap: Arik Nemtsov <arik@wizery.com>
Add some more functionality for BSS Transition Management:
- advertise support for BSS Transition Management in extended
capabilities element
- add hostapd.conf parameter bss_transition=1 for enabling support
for BSS Transition Management
- add "hostapd_cli disassoc_imminent <STA> <num TBTTs>" for sending
disassociation imminent notifications for testing purposes
- wpa_supplicant: trigger a new scan to find another BSS if the
current AP indicates disassociation imminent (TODO: the old AP needs
to be marked to use lower priority to avoid re-selecting it)
Signed-hostap: Jouni Malinen <j@w1.fi>
hostapd can run with different VIF when using nl80211. Events about MIC
failures have to be processed in context of the VIF which received it
and not in context of the primary VIF. Otherwise the station belonging
to this VIF may not be found in the primary VIF station hash and
therefore no countermeasures are started or the countermeasures are
started for the wrong VIF.
Signed-hostap: Sven Eckelmann <sven@open-mesh.com>
Signed-hostap: Simon Wunderlich <simon@open-mesh.com>
This optional attribute may make it easier to bind together the
Access-Request and Accounting-Request messages. The accounting session
identifier is now generated when the STA associates instead of waiting
for the actual session to start after successfull authentication.
Signed-hostap: Jouni Malinen <j@w1.fi>
Basic support for the 60 GHz band. Neither P2P nor WPS are yet taken
care off. Allows to start AP with very simple config:
network={
ssid="test"
mode=2
frequency=60480
key_mgmt=NONE
}
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The config says that the default for ap_table_max_size is 255 and the
default for ap_table_expiration_time is 60. But the code doesn't reflect
the default values mentioned in the sample config file.
These variables completely disable the code for Overlapping Legacy BSS
Condition by default when they are not correctly initialized. WFA
certification requires this feature and therefore an AP would have
failed the certification process unless they were initialized manually
using the configuration file.
Signed-hostap: Sven Eckelmann <sven@open-mesh.com>
Signed-hostap: Simon Wunderlich <simon@open-mesh.com>
WSC IE in Beacon and Probe Response frames should behave consistently
as far as the RF Bands attribute is concerned. Use the same dualband
condition for adding this into Probe Response frames since the value
is not really needed if the AP is not a dualband AP.
Signed-hostap: Jouni Malinen <j@w1.fi>
If separate hostapd processes are used for different RF bands, the
dualband parameter for WPS was not set correctly. Allow dualband
indication (mainly, addition of RF bands attribute for PBC session
overlap detection) also based on wps_rf_bands value (if set to "ag").
Signed-hostap: Jouni Malinen <j@w1.fi>
This allows Probe Request frame processing to compare the configured
SSID to the SSID List element in addition to the SSID element.
Signed-hostap: Jouni Malinen <j@w1.fi>
Replace CONFIG_IEEE80211V with CONFIG_WNM to get more consistent build
options for WNM-Sleep Mode operations. Previously it was possible to
define CONFIG_IEEE80211V without CONFIG_WNM which would break the build.
In addition, IEEE 802.11v has been merged into IEEE Std 802.11-2012 and
WNM is a better term to use for this new functionality anyway.
Signed-hostap: Jouni Malinen <j@w1.fi>
These fields do not use AES keywrap. Instead, they are protected with
management frame protection (and not included if PMF is disabled).
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Expiry can always trigger a deauthentication, but otherwise,
deauthentication should only happen when the *current* cache entry is
removed and not being replaced. It should not happen when the current
PMK just happens to match the PMK of the entry being removed, since
multiple entries can have the same PMK when OKC is used and these
entries are often removed at different times.
This fixes an issue where eviction of the oldest inactive entry due to
adding a newer entry to a full cache caused a deauthentication when the
entry being removed had the same PMK as the current entry.
Signed-hostap: Dan Williams <dcbw@redhat.com>
pmksa_cache_free_entry() takes care of updated the list head pointer
(pmksa->pmksa), so no need to do this change in the caller.
Signed-hostap: Jouni Malinen <j@w1.fi>
Use the shared_secret pointer from RADIUS client implementation instead
of getting this from hostapd configuration data.
Signed-hostap: Jouni Malinen <j@w1.fi>
This adds support for multiple PSKs per station when using a RADIUS
authentication server to fetch the PSKs during MAC address
authentication step. This can be useful if multiple users share a
device but each user has his or her own private passphrase.
Signed-hostap: Michael Braun <michael-dev@fami-braun.de>
Add pmf=1/2 to wpa_supplicant STATUS command output to indicate that PMF
was negotiated for the connect (1 = optional in this BSS, 2 = required
in this BSS).
Signed-hostap: Jouni Malinen <j@w1.fi>
Previously, PMF (protected management frames, IEEE 802.11w) could be
enabled only with a per-network parameter (ieee80211w). The new global
parameter (pmf) can now be used to change the default behavior to be PMF
enabled (pmf=1) or required (pmf=2) for network blocks that do not
override this with the ieee80211w parameter.
Signed-hostap: Jouni Malinen <j@w1.fi>
We enable this feature for non-SME drivers as well if
they explicitly indicate need for it.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Add the configuration option vht_oper_centr_freq_seg1_idx
for the second segment of an 80+80 MHz channel and use it
when building the VHT operation IE.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
If netlink_init() fails on socket create or bind the cfg struct
provided as parameter is freed by netlink_init(). Callers of
netlink_init() also free this struct on their error paths leading
to double free.
Signed-hostap: Pontus Fuchs <pontus.fuchs@gmail.com>
This allows the AP to figure out whether a station is a HS 2.0 STA
during the association and access any information that the STA may have
included in this element.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Change the maximum retry limit from 10 to 120 to match the behavior
used with GO Negotiation Request frames when trying to start GO
Negotiation with a peer that does not acknowledge frames (e.g., due
to being in sleep or on another channel most of the time).
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The GO may be in sleep when we send a PD Request frame to indicate that
we are about to join a running group. Previously, this frame was not
retried more than normal low level retries. This can result in the GO
not getting the frame especially in cases where concurrent multi-channel
operations or aggressive sleep schedule is used since most drivers do
not yet synchronize with the GO's NoA before association.
Increase the likelihood of the GO receiving the PD Request frame by
retransmitting it similarly to the PD-for-GO-Negotiation case. Start
the actual join operation only after these retries have failed to get
an acknowledgment from the GO to give the connection attempt a chance
to succeed if the driver implements better NoA synchronization for it.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
p2p_prov_disc_req() used the join parameter to figure out whether the PD
request was a user initiated or not. This does not cover all use cases
of PD, so add a separate parameter to allow caller to indicate whether
the user requested the operation.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
CONFIG_SQLITE=y option can now be used to allow the eap_user_file text
file to be replaced with a SQLite database
(eap_user_file=sqlite:/path/to/sqlite.db). hostapd.eap_user_sqlite
shows an example of how the database tables can be created for this
purpose. This commit does not yet include full functionality of the
text file format, but at least basic EAP-TTLS/MSCHAPv2 style
authentication mechanisms with plaintext passwords can be used for
tests.
Signed-hostap: Jouni Malinen <j@w1.fi>
The NL80211_CMD_TDLS_OPER command can be used as an event based on a
recent cfg80211 commit, so add code to map that to internal
wpa_supplicant event to request TDLS link setup/teardown.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Commit 296a34f0c1 changed hostapd to
remove the internal STA entry at the beginning of TKIP countermeasures.
However, this did not take into account the case where this is triggered
by an EAPOL-Key error report from a station. In such a case, WPA
authenticator state machine may continue processing after having
processed the error report. This could result in use of freed memory.
Fix this by stopping WPA processing if the STA entry got removed.
Signed-hostap: Jouni Malinen <j@w1.fi>
Some deployed station implementations implement WPS incorrectly and
end up causing PBC session overlap issues by indicating active PBC
mode in a scan after the WPS provisioning step. Work around this by
ignoring active PBC indication in a Probe Request from a station that
completed PBC provisioning during the last five seconds.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Commits 07783eaaa0 and
3da372fae8 removed the only users of the
disassociate() driver operation, so these driver wrapper functions can
also be removed now.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Change the nl80211 driver in wpa_supplicant to correctly handle
connecting to a new AP through cfg80211 without SME capability. As
before, the driver will disconnect from the previously associated AP,
but now we attempt to immediately connect to our intended AP. This
prevents us from blacklisting the AP we were trying to connect to
because of a semantic mismatch between cfg80211 and wpa_supplicant. The
disconnect/connect patch generates a local disconnect nl80211 event
which we discard because we're already correctly tracking the pending
association request.
In detail:
cfg80211 does not support connecting to a new BSS while already
connected to another BSS, if the underlying driver doesn't support
separate authenticate and associate commands. wpa_supplicant is written
to expect that this is a supported operation, except for a little error
handling that disconnects from the current BSS when roaming fails and
relies on autoconnect logic to reconnect later. However, this failure to
connect is incorrectly attributed to the new AP we attempted to
associate with, rather than a local condition in cfg80211.
The combined effect of these two conditions is that full-mac drivers
accessible through cfg80211 but without SME capability take a long time
to roam across BSS's because wpa_supplicant will:
1) Fail to associate for local reasons
2) Disconnect and return that the association request failed
3) Blacklist the association target (incorrectly)
4) Do a scan
5) Pick a less desirable AP to associate with
Signed-hostap: Christoper Wiley <wiley@chromium.org>
Commit deca6eff74 added a redundant call
to l2_packet_get_own_addr. Use the information we already have in
atheros_init.
Signed-hostap: Baruch Siach <baruch@tkos.co.il>
If identity round limit is reached, EAP-SIM/AKA session is terminated.
This needs to free the allocated message.
Signed-hostap: Jouni Malinen <j@w1.fi>
There is no point in the hapd_iface == NULL validate after this pointer
has been dereferences, so move the code dereferencing hapd_iface after
the check.
Signed-hostap: Jouni Malinen <j@w1.fi>
The UFD (USB flash drive) configuration method was deprecated in WSC
2.0. Since this is not known to be used, remove the UFD implementation
from hostapd and wpa_supplicant to allow the WPS implementation to be
cleaned up. This removes the now unused OOB operations and ctrl_iface
commands that had already been deprecated by the new NFC operations.
Signed-hostap: Jouni Malinen <j@w1.fi>
The PSK generation done by pbkdf2_sha1() is one of the longest CPU time
users according to our profiling from boot to GO started.
So I have reduced some steps.
I could boot a GO by this command sequence.
-------------
add_net
set_network 0 ssid '"DIRECT-XX"'
set_network 0 psk
'"123456789012345678901234567890123456789012345678901234567890123"'
set_network 0 proto RSN
set_network 0 key_mgmt WPA-PSK
set_network 0 pairwise CCMP
set_network 0 auth_alg OPEN
set_network 0 mode 3
set_network 0 disabled 2
p2p_group_add persistent=0 freq=2412
-------------
By this sequence, pbkdf2_sha1() was called three times and the function
calculates the same value each time. Reduce number of calls to
pbkdf2_sha1() from 3 to 1 by caching the previous result.
Signed-hostap: Masashi Honma <masashi.honma at gmail.com>
This function is now unused after the last couple of commits that
removed the last uses, so remove this to keep code simpler since all
places that disassociate, can use deauthentication instead.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Even though the standard currently describes disassociation to be used
for RSN element mismatch between Beacon/Probe Response frames and
EAPOL-Key msg 3/4, this is unnecessary difference from other cases that
deauthenticate. In addition, there is no point in leaving the 802.11
Authentication in place in this case. To keep things simpler, use
deauthentication here to get rid of the only use of
wpa_sm_disassociate().
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
If WPS Registrar tries to provision a WPA/WPA2-Personal network without
including a valid Network Key, the network block cannot be used to
connect to the network. Reject such credential without adding the
network block. This makes wpa_supplicant send WSC_NACK as a response to
the invalid Credential and stop the provisioning process immediately
rather than only after trying unsuccessfully to connect to the network.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The new P2P_SET parameter disc_int can now be used to configure
discoverable interval for p2p_find operations. The format of the command
for setting the values is "P2P_SET disc_int <minDiscoverableInterval>
<maxDiscoverableInterval> <max TUs for discoverable interval>". The
first two parameters are given in units of 100 TUs (102.4 ms). The third
parameter can be used to further limit the interval into a specific TU
amount. If it is set to -1, no such additional limitation is enforced.
It should be noted that the P2P specification describes the random
Listen state interval to be in units of 100 TUs, so setting the max TU
value to anything else than -1 is not compliant with the specification
and should not be used in normal cases. The default parameters can be
set with "P2P_SET disc_int 1 3 -1".
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The old WPS interface for using NFC has no known deployments and even
the binary libraries referenced here are not easily available anymore.
Since the new interface for using NFC with WPS covers the same
functionality, remove the old implementation to clean up WPS
implementation.
Signed-hostap: Jouni Malinen <j@w1.fi>
When WPS is used with NFC connection handover, the AP may indicate its
operating channel within the credential information. Use this
informatiom, if present, to speed up the scan process.
Signed-hostap: Jouni Malinen <j@w1.fi>
This commit adds new wpa_supplicant ctrl_iface commands to allow
external programs to go through NFC connection handover mechanism
with wpa_supplicant taking care of the WPS processing. This version
includes only the case where wpa_supplicant is operating as a
station/Enrollee.
Signed-hostap: Jouni Malinen <j@w1.fi>
The previous eapol_sm_notify_cached() implementation forced the port
to be authorized when receiving EAPOL-Key msg 1/4 that included a
matching PMKID in cases when PMKSA caching is used. This is too early
since the port should really be authorized only after the PTK has been
configured which is the case when PMKSA caching is not used.
Fix this by using the EAPOL supplicant PAE state machine to go through
the AUTHENTICATING and AUTHENTICATED states instead of forcing a jump
to AUTHENTICATED without performing full state machine steps. This can
be achieved simply by marking eapSuccess TRUE at least with the current
version of EAP and EAPOL state machines (the earlier commits in this
function seemed to indicate that this may have not been that easy in
the older versions due to the hacks needed here).
This addresses an issue with nl80211-based driver interface when the
driver depends on the STA Authorized flag being used to prevent
unprotected frames from being accepted (both TX and RX) prior to PTK
configuration.
Signed-hostap: Jouni Malinen <j@w1.fi>
intended-for: hostap-1
If the driver indicates support for multi-channel concurrency, change
the p2p_connect behavior to not force the current operating channel, but
instead, just mark it as preferred for GO Negotiation. This change
applies only for the case when the freq parameter is not used with the
p2p_connect command.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
There was an issue with EAPOL frame exchanges in a multi-BSS
configuration when a station switches between the BSSes controlled by
the same hostapd process. When processing the EAPOL packet, the array of
virtual APs (iface->bss) is searched looking for the station that sent
the packet in order to identify which signal context should be used
during processing. The first match of the station in its list gets used
in the ieee802_1x_receive() function. However, even after a station has
disassociated, it remains in the list of stations pending an inactivity
timeout. This leads to the wrong hapd context (one where the station had
already disassociated) being used in some cases (if the current/active
bss entry appears in the list after one where the station has just
disassociated from) for EAPOL processing.
Fix this by checking the WLAN_STA_ASSOC flag before assuming the right
hapd context was found for the given station.
Signed-hostap: David Bird <dbird@powercloudsystems.com>
intended-for: hostap-1
This uses the recent cfg80211 changes to allow SAE authentication to be
implemented with the nl80211 driver interface.
Signed-hostap: Jouni Malinen <j@w1.fi>
P2P includes two use cases where one of the devices is going to start a
group and likely change channels immediately after processing a frame.
This operation may be fast enough to make the device leave the current
channel before the peer has completed layer 2 retransmission of the
frame in case the ctrl::ack frame was lost. This can result in the peer
not getting TX status success notification.
For GO Negotiation Confirm frame, p2p_go_neg_conf_cb() has a workaround
that ignores the TX status failure and will continue with the group
formation with the assumption that the peer actually received the frame
even though we did not receive ctrl::ack. For Invitation Response frame
to re-invoke a persistent group, no such workaround is used in
p2p_invitation_resp_cb(). Consequently, TX status failure due to lost
ctrl::ack frame results in one of the peers not starting the group.
Increase the likelihood of layer 2 retransmission getting acknowledged
and ctrl::ack being received by waiting a short duration after having
processed the GO Negotiation Confirm and Invitation Response frames for
the re-invocation case. For the former, use 20 ms wait since this case
has been worked around in deployed devices. For the latter, use 50 ms
wait to get even higher likelihood of getting ctrl::ack through since
deployed devices (and the current wpa_supplicant implementation) do not
have a workaround to ignore TX status failure.
20 ms is long enough to include at least couple of retries and that
should increase likelihood of getting ctrl::ack through quite a bit. The
longer 50 ms wait is likely to include full set of layer 2 retries.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Commit 458cb30191 broke LEAP since it
rejects EAP-Success packet that is used within LEAP and this frame does
not have a payload. Fix LEAP by relaxing the generic EAP packet
validation if LEAP has been negotiated.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Previously, WPS Registrar allowed multiple wildcard PINs to be
configured. This can get confusing since these PINs get assigned to any
Enrollee that does not have a specific PIN and as such, cannot really be
used with different PIN values in reasonable ways. To avoid confusion
with multiple enabled PINs, invalidate any previously configured
wildcard PIN whenever adding a new one.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
While the existing code already addresses TLS Message Length validation
for both EAP-TLS peer and server side, this adds explicit checks and
rejection of invalid messages in the functions handling reassembly. This
does not change externally observable behavior in case of EAP server.
For EAP peer, this starts rejecting invalid messages instead of
addressing them by reallocating the buffer (i.e., ignoring TLS Message
Length in practice).
Signed-hostap: Jouni Malinen <j@w1.fi>
EAP-TLS/PEAP/TTLS/FAST server implementation did not validate TLS
Message Length value properly and could end up trying to store more
information into the message buffer than the allocated size if the first
fragment is longer than the indicated size. This could result in hostapd
process terminating in wpabuf length validation. Fix this by rejecting
messages that have invalid TLS Message Length value.
This would affect cases that use the internal EAP authentication server
in hostapd either directly with IEEE 802.1X or when using hostapd as a
RADIUS authentication server and when receiving an incorrectly
constructed EAP-TLS message. Cases where hostapd uses an external
authentication are not affected.
Thanks to Timo Warns for finding and reporting this issue.
Signed-hostap: Jouni Malinen <j@w1.fi>
intended-for: hostap-1
This replaces the previously used bogus test data in SAE messages with
the first real field. The actual SAE authentication mechanism is still
missing and the Scaler, Element, and Confirm fields are not included.
Signed-hostap: Jouni Malinen <j@w1.fi>
Channel frequency for 60 GHz band do not fit into 'short int', as was
used. Expand it to 'int'
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
These values are used with WAPI and CCX and reserving the definitions
here reduces the number of merge conflicts with repositories that
include these functions.
Signed-hostap: Jouni Malinen <j@w1.fi>
This introduces new AKM for SAE and FT-SAE and adds the initial parts
for going through the SAE Authentication frame exchange. The actual SAE
algorithm and new fields in Authentication frames are not yet included
in this commit and will be added separately. This version is able to
complete a dummy authentication with the correct authentication
algorithm and transaction values to allow cfg80211/mac80211 drivers to
be tested (all the missing parts can be handled with
hostapd/wpa_supplicant changes).
Signed-hostap: Jouni Malinen <j@w1.fi>
This allows hostapd_cli and wpa_cli all_sta command to be used to
display connected time (in seconds) of each station in AP mode.
Signed-hostap: Raja Mani <rmani@qca.qualcomm.com>
Commit 6b56cc2d97 added clearing of the
p2p->pending_action_state too early in this function. This should not
be done if we are going to silently ignore the frame due to dialog
token mismatch. Fix this by moving the code around to check the dialog
token first.
This issue resulted in PD Request retries getting stopped too early if
the peer is sending out an unexpected PD Response (e.g., because of it
being excessively slow with the response so that the response is
received only after the next TX attempt with a new dialog token).
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Make Invitation process for re-invoking a persistent group behave
similarly to GO Negotiation as far as channel negotiation is concerned.
The Operating Channel value (if present) is used as a starting point if
the local device does not have a forced operating channel (e.g., due to
concurrent use). Channel lists from devices are then compared to check
that the selected channel is in the intersection. If not, channel is
selected based on GO Negotiation channel rules (best channel preferences
etc.). Invitation Request is rejected if no common channel can be
selected.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
As long as WLAN_STA_ASSOC_REQ_OK is set in sta->flags, Class 3 frames do
not trigger a disassoc/deauth. If it is still set even after the assoc
response tx has already failed, it may take somewhat longer for clients
to realize that the connection wasn't fully established.
Signed-hostap: Felix Fietkau <nbd@openwrt.org>
This avoids extra latency caused by establishing an aggregation session
and makes the initial connection attempt more reliable
Signed-hostap: Felix Fietkau <nbd@openwrt.org>
This patch fixes an issue where removing a WDS VLAN interface also
removed the main AP interface from the same bridge.
Signed-hostap: Felix Fietkau <nbd@openwrt.org>
This is a generic AES CCM implementation that can be used for other
purposes than just implementing CCMP, so it fits better in a separate
file in src/crypto.
Signed-hostap: Jouni Malinen <j@w1.fi>
Now that the internal AES implementation supports 256-bit keys, enable
use of the TLS cipher suites that use AES-256 regardless of which crypto
implementation is used.
Signed-hostap: Jouni Malinen <j@w1.fi>
AES uses the same 128-bit block size with 128, 192, 256 bit keys, so use
the fixed block size definition instead of trying to dynamically set the
block size based on key length. This fixes use of 192-bit and 256-bit
AES keys with crypto_cipher_*() API when using the internal AES
implementation.
Signed-hostap: Jouni Malinen <j@w1.fi>
This is otherwise identical to aes_gcm_ae() but does not use the
plain/crypt pointers since no data is encrypted.
Signed-hostap: Jouni Malinen <j@w1.fi>
This adds 192-bit and 256-bit key support to the internal AES
implementation and extends the AES-GCM functions to accept key length to
enable longer AES key use.
Signed-hostap: Jouni Malinen <j@w1.fi>
This is a generic AES GCM and GMAC implementation that can be used for
other purposes than just implementing GCMP, so it fits better in a
separate file in src/crypto.
Signed-hostap: Jouni Malinen <j@w1.fi>
The conf doesn't contain any basic rates in some cases. Most notably,
when starting a P2P GO in 5 GHz. Use the iface rates which are
initialized in hostapd_prepare_rates() to the conf rates or set to
default values if no conf values exist. This fixes a bug introduced in
commit e5693c4775.
Signed-hostap: Arik Nemtsov <arik@wizery.com>
Commit e5693c4775 added a copy of the
determined basic rate set into struct hostapd_iface, but did not
actually copy the terminating -1 value. This could be problematic if
something were to actually try to use this list since would be no way to
know what is the last entry in the list. Fix this by copying the
terminating value.
Signed-hostap: Jouni Malinen <j@w1.fi>
This driver_op can now be used in station mode, too, to fetch
information about the connection with the AP, so allow this to be used
even if wpa_supplicant is built without AP mode support.
Signed-hostap: Jouni Malinen <j@w1.fi>
The group matching should be done by comparing the P2P Interface Address
(which the group_bssid here is) to the group's BSSID and not the group
ID (which uses P2P Device Address and would have also needed the SSID).
Though, it should be noted that this case cannot really happen since a
GO in an active group would never be invited to join another group in
its GO role (i.e., if it receives an Invitation Request, it will reply
in P2P Device role). As such, this fix does not really change any
observable behavior, but anyway, it is good to keep the implementation
here consistent with the Invitation Request case.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
When building the Invitation Request for WFD use cases, match the BSSID,
i.e., P2P Interface Address, of the group on the GO to avoid using
information from another group should the device be operating multiple
concurrent groups as GO.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Use the anonymous_identity field to store EAP-SIM/AKA pseudonym identity
so that this can be maintained between EAP sessions (e.g., after
wpa_supplicant restart) even if fast re-authentication data was cleared.
Signed-hostap: Jouni Malinen <j@w1.fi>
The EAP-SIM/AKA code is already validating the prefix and the following
lookup would not find matches if the prefix is incorrect, so there is no
need for the extra checks here.
Signed-hostap: Jouni Malinen <j@w1.fi>
If EAP-Response/Identity includes a known pseudonym or re-auth username,
skip the AKA/Identity exchange since we already know the permanent
username of the peer.
Signed-hostap: Jouni Malinen <j@w1.fi>
RFC 4186, chapter 6.3.3 mandates that EAP-Failure is used only after
Client-Error and Notification messages. Convert the direct jumps to the
FAILURE state with a notification round before sending out EAP-Failure.
Signed-hostap: Jouni Malinen <j@w1.fi>
The AT_NONCE_S value needs to be used in AT_MAC calculation for
SIM/Re-authentication response even if re-authentication is rejected
with AT_COUNTER_TOO_SMALL.
Signed-hostap: Jouni Malinen <j@w1.fi>
intended-for: hostap-1
If the peer rejects re-authentication with AT_COUNTER_TOO_SMALL, fall
back to full authentication to allow the authentication session to be
completed.
Signed-hostap: Jouni Malinen <j@w1.fi>
These fields are used only as the search key, so the value is already
known and does not need to be copied from the database.
Signed-hostap: Jouni Malinen <j@w1.fi>
Store permanent username (i.e., including prefix character) instead of
IMSI in the SQLite DB. Convert the string to a string since the EAP-AKA
prefix can start with zero. This cleans up the field names since the
value was already with the prefix included instead of just IMSI. In
addition, this explicitly removes some theoretical cases where the
different identity types could have been mixed.
Signed-hostap: Jouni Malinen <j@w1.fi>
Since the EAP-SIM/AKA identities are ASCII strings, there is no need to
use more complex way for storing and passing them. In addition, be more
strict about enforcing username (i.e., no realm part) to be used in the
EAP-SIM DB API. Similarly, require specific username type instead of any
of the types to be used as the key in the pseudonym and reauth
operations. This allows simpler lookup operations to be used.
Signed-hostap: Jouni Malinen <j@w1.fi>
Since we always request an identity in the request, the response
has to include AT_IDENTITY. This allows the AKA/Identity response
processing to be simplified a bit.
Signed-hostap: Jouni Malinen <j@w1.fi>
There is no need to use eap_sim_db_identity_known() here since a new
AKA/Identity message is built only if the identity in the previous
response was not recognized. The first round is always used to request
AT_ANY_ID_REQ to meet the RFC 4187 recommendation on EAP method specific
identity request.
Signed-hostap: Jouni Malinen <j@w1.fi>
Since we always request an identity in the request, the response
has to include AT_IDENTITY. This allows the SIM/Start response
processing to be simplified a bit.
Signed-hostap: Jouni Malinen <j@w1.fi>
There is no need to use eap_sim_db_identity_known() here since a new
SIM/Start message is built only if the identity in the previous response
was not recognized. The first round will always request AT_ANY_ID_REQ to
meet the RFC 4186 recommendation on EAP method specific identity request
being used.
Signed-hostap: Jouni Malinen <j@w1.fi>
The reauth_id prefix can be used to determine which AKA version is used,
so there is no need to store the aka_prime information in a separate
field.
Signed-hostap: Jouni Malinen <j@w1.fi>
If hostapd is built and configured to use SQLite database, store
EAP-SIM/AKA reauth data into the database to allow this to persist
over hostapd restarts.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This allows hostapd to use an SQLite database for storing EAP-SIM/AKA
pseudonyms over process restarts. CONFIG_SQLITE=y build option adds
support for this and the SQLite database file is specified in eap_sib_db
configuration parameter.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Try to share most of the cipher information like key and RSC lengths and
suite selector conversions, etc. in wpa_common.c to avoid having similar
code throughout the WPA implementation for handling cipher specific
behavior.
Signed-hostap: Jouni Malinen <j@w1.fi>
wpa_cli p2p_serv_disc_req command can now be used to request WSD
request to be sent to specified or all peers who support WSD.
format: wifi-display <list of roles> <list of subelements>
examples:
p2p_serv_disc_req 00:00:00:00:00:00 wifi-display [source] 2,3,4,5
p2p_serv_disc_req 02:01:02:03:04:05 wifi-display [pri-sink] 3
p2p_serv_disc_req 00:00:00:00:00:00 wifi-display [sec-source] 2
p2p_serv_disc_req 00:00:00:00:00:00 wifi-display [source+sink] 2,3,4,5
p2p_serv_disc_req 00:00:00:00:00:00 wifi-display [source][pri-sink] 2,3,4,5
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This commit adds control interface commands and internal storage of
Wi-Fi Display related configuration. In addition, WFD IE is now added
to various P2P frames, Probe Request/Response, and (Re)Association
Request/Response frames. WFD subelements from peers are stored in the
P2P peer table.
Following control interface commands are now available:
SET wifi_display <0/1>
GET wifi_display
WFD_SUBELEM_SET <subelem> [hexdump of length+body]
WFD_SUBELEM_GET <subelem>
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This allows both hostapd and wpa_supplicant to be used to derive and
configure keys for GCMP. This is quite similar to CCMP key
configuration, but a different cipher suite and somewhat different rules
are used in cipher selection. It should be noted that GCMP is not
included in default parameters at least for now, so explicit
pairwise/group configuration is needed to enable it. This may change in
the future to allow GCMP to be selected automatically in cases where
CCMP could have been used.
This commit does not included changes to WPS or P2P to allow GCMP to be
used.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Use the NL80211_IFACE_COMB_NUM_CHANNELS value > 1 as a trigger for
enabling support for P2P multichannel channel concurrency. This does not
handle all possible details of enforcing driver capabilities, but it is
a good first step for allowing nl80211 drivers to enable multichannel
concurrency.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The new gas_request and gas_response_get commands can be used to request
arbitary GAS queries to be performed. These can be used with ANQP or
with other (including vendor specific) advertisement protocols.
gas_request <BSSID> <AdvProtoID> [Query]
gas_response_get <addr> <dialog token> [offset,length]
For example, ANQP query for Capability list in interactive wpa_cli
session:
> gas_request 02:00:00:00:01:00 00 000102000101
<3>GAS-RESPONSE-INFO addr=02:00:00:00:01:00 dialog_token=0
status_code=0 resp_len=32
> gas_response_get 02:00:00:00:01:00 00
01011c00010102010501070108010c01dddd0c00506f9a110200020304050607
> gas_response_get 02:00:00:00:01:00 00 0,10
01011c00010102010501
> gas_response_get 02:00:00:00:01:00 00 10,10
070108010c01dddd0c00
> gas_response_get 02:00:00:00:01:00 00 20,10
506f9a11020002030405
> gas_response_get 02:00:00:00:01:00 00 30,2
0607
It should be noted that the maximum length of the response buffer is
currently 4096 bytes which allows about 2000 bytes of the response data
to be fetched with a single gas_response_get command. If the response is
longer, it can be fetched in pieces as shown in the example above.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The new vendor_elements parameter in hostapd.conf can be used to add new
vendor specific element(s) into Beacon and Probe Response frames.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Maintain state of WPS APs during iteration to find the correct AP for
WPS PIN operation when no specific BSSID is specified. This information
can be used for optimizing the order in which the APs are tried. This
commit is only adding the collection of the information and more
detailed debug information to make debug logs more helpful in figuring
out how the AP selection order could be improved.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
If 4-way handshake fails due to likely PSK failure or if EAP
authentication fails, disable the network block temporarily. Use longer
duration if multiple consecutive failures are seen.
Signed-hostap: Jouni Malinen <j@w1.fi>
Replace the Venue Name specific data structure and parser with a
generic mechanism that can be used with other fields that use the
same format.
Signed-hostap: Jouni Malinen <j@w1.fi>
The anqp_3gpp_cell_net parameter can be used to configure hostapd
to advertise 3GPP Cellular Network ANQP information.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
These function pointers are going to be the same for each interface so
there is no need to keep them in struct hostapd_iface. Moving them to
struct hapd_interfaces makes it easier to add interfaces at run time.
Signed-hostap: Jouni Malinen <j@w1.fi>
The driver_test.c data structures had been changed to use a separate
BSS structure, but the P2P commands were not using the new design.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Commit 488f4a7108 configures a timer
before p2p_send_action(). This may result in the timer getting fired
earlier to the off channel transmission of the frame and thus another PD
request being retransmitted. This shall lead to the new PD request with
an incremented dialog token being transmitted. For the cases where the
later PD request might not be transmitted as the host driver is busy
transmitting the earlier frame, the received PD response could be
dropped for the dialog token mismatch. Remove the timer configuration to
avoid this behavior.
Signed-hostap: Sunil Dutt Undekari <duttus@codeaurora.org>
intended-for: hostap-1
Previously, all station mode scan operations were either skipped or
delayed while any P2P operation was in progress. To make concurrent
operations easier to use, reduce this limitation by allowing a scan
operation to be completed in the middle of a p2p_find. In addition,
allow station mode association to be completed. When the station mode
operation is run to its completion (scan results not acted on,
connection to an AP completed, connection failed), resume the p2p_find
operation.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
A new optional delay=<search delay in milliseconds> parameter can now be
used with p2p_find command to request an extra delay between search
iterations. This can be used, e.g., to make p2p_find friendlier to
concurrent operations by avoiding it from taking 100% of the radio
resources.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This EAP type uses a vendor specific expanded EAP header to encapsulate
EAP-TLS with a configuration where the EAP server does not authenticate
the EAP peer. In other words, this method includes only server
authentication. The peer is configured with only the ca_cert parameter
(similarly to other TLS-based EAP methods). This method can be used for
cases where the network provides free access to anyone, but use of RSN
with a securely derived unique PMK for each station is desired.
The expanded EAP header uses the hostapd/wpa_supplicant vendor
code 39068 and vendor type 1 to identify the UNAUTH-TLS method.
Signed-hostap: Jouni Malinen <j@w1.fi>
The previous implementation was able to re-open the connection to an
external program (e.g., hlr_auc_gw) when needed, but required the
connection to be available during startup. Extend this to allow the
initial failure, so that hlr_auc_gw can be started after hostapd.
Signed-hostap: Jouni Malinen <j@w1.fi>
Explicitly validate seed_len to skip memset call with zero length of
copied data at the end of the buffer. This is not really needed, but it
makes the code a bit easier for static analyzers. This is identical to
the commit a9ea17491a but for the OpenSSL
version of the function.
Signed-hostap: Jouni Malinen <j@w1.fi>
Commit bfc62fe133 moved the code that
using crypto/random.h, but forgot to remove the inclusion of that header
file.
Signed-hostap: Jouni Malinen <j@w1.fi>
All the TNC base64 operations are within tncs.c, so there is no point in
including base64.h into eap_server_tnc.c.
Signed-hostap: Jouni Malinen <j@w1.fi>
All the other places processing EVENT_RX_MGMT events assume that the
event data is included, so not much point in verifying that here.
Signed-hostap: Jouni Malinen <j@w1.fi>
Use an explicit pointer to the beginning of the buffer and a flag
to indicate whether that is to external data or not. This avoids
a branch whenever accessing the buffer and helps some static
analyzers to understand the wpabuf memory uses better.
Signed-hostap: Jouni Malinen <j@w1.fi>
If the os_malloc() call for the User-Name value fails in EAP-TTLS
server, the inner MSCHAPv2 processing could have tried to dereference a
NULL pointer. Avoid this by handling this cleanly as an internal error
and reject the authentication attempt.
Signed-hostap: Jouni Malinen <j@w1.fi>
intended-for: hostap-1
Commit c9e08af24f removed the only user of
the special case MD5 use that would be allowed in FIPS mode in
tls_prf_sha1_md5(). Commit 271dbf1594
removed the file from the build, but left the implementation into the
repository. To clean things up even further, remove this functionality
completely since it is not expected to be needed for FIPS mode anymore.
Signed-hostap: Jouni Malinen <j@w1.fi>
This allows User-Name and Chargeable-User-Identity attributes to be
passed from Access-Accept into Accounting messages even when IEEE 802.1X
is not used.
Signed-hostap: Michael Braun <michael-dev@fami-braun.de>
The mechanism to figure out key block size based on ssl->read_hash
does not seem to work with OpenSSL 1.0.1, so add an alternative
mechanism to figure out the NAC key size that seems to work at
least with the current OpenSSL 1.0.1 releases.
Signed-hostap: Jouni Malinen <j@w1.fi>
intended-for: hostap-1
Some deployed authentication servers seem to be unable to handle the TLS
Session Ticket extension (they are supposed to ignore unrecognized TLS
extensions, but end up rejecting the ClientHello instead). As a
workaround, disable use of TLS Sesson Ticket extension for EAP-TLS,
EAP-PEAP, and EAP-TTLS (EAP-FAST uses session ticket, so any server that
supports EAP-FAST does not need this workaround).
Signed-hostap: Jouni Malinen <j@w1.fi>
tls_disable_session_ticket=1 in phase1/phase2 can now be used to disable
use of TLS Session Ticket extension (which is enabled by default in
recent OpenSSL versions). This can be used to work around issues with
broken authentication servers that do not ignore unrecognized TLS
extensions properly.
Signed-hostap: Jouni Malinen <j@w1.fi>
This can be used to implement workaround for authentication servers that
do not handle TLS extensions in ClientHello properly.
Signed-hostap: Jouni Malinen <j@w1.fi>
The PKCS5_PBKDF2_HMAC_SHA1() function in OpenSSL 0.9.7 did not mark
the salt parameter const even though it was not modified. Hide the
compiler warning with a type cast when an old OpenSSL version is
used.
Signed-hostap: Jouni Malinen <j@w1.fi>
When CONFIG_FIPS=y is used, do not include MD5 in the build and disable
EAPOL-Key frames that use MD5 (WPA/TKIP and dynamic WEP with IEEE
802.1X).
Signed-hostap: Jouni Malinen <j@w1.fi>
Only allow the TLS library keying material exporter functionality to be
used for MSK derivation with TLS-based EAP methods to avoid exporting
internal TLS keys from the library.
Signed-hostap: Jouni Malinen <j@w1.fi>
Use SSL_export_keying_material() if possible, i.e., if OpenSSL is
version 1.0.1 or newer and if client random value is used first. This
allows MSK derivation with TLS-based EAP methods (apart from EAP-FAST)
without exporting the master key from OpenSSL.
Signed-hostap: Jouni Malinen <j@w1.fi>
Previously, CONFIG_EAP_MSCHAPV2=y was assumed to be set for
CONFIG_EAP_TTLS=y. Avoid this dependency by making including the
MSCHAPv2 parts in EAP-TTLS conditionally.
Signed-hostap: Jouni Malinen <j@w1.fi>
In theory, the SHA1 operation may fail (e.g., if SHA1 becomes disallowed
in some security policies), so better check the return code from
challenge_hash().
Signed-hostap: Jouni Malinen <j@w1.fi>
Do not leave the tls_global context allocated if the global OpenSSL
initialization fails. This was possible in case of FIPS builds if
the FIPS mode cannot be initialized.
Signed-hostap: Jouni Malinen <j@w1.fi>
Increase GO config timeout if HT40 is used since it takes some time
to scan channels for coex purposes before the BSS can be started.
Signed-hostap: Jouni Malinen <j@w1.fi>
Add optional "ht40" argument for p2p_group_add command to enable 40 MHz
in 5GHz band. This configures the secondary channel, when HT support is
enabled and if the HW supports 40 MHz channel width.
Signed-hostap: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
This function can be used as a wrapper for os_realloc(ptr, nmemb * size)
when a reallocation is used for an array. The main benefit over
os_realloc() is in having an extra check to catch integer overflows in
multiplication. This is similar to the os_zalloc() to os_calloc() move.
Signed-hostap: Jouni Malinen <j@w1.fi>
This function can be used as a wrapper for os_zalloc(nmemb * size) when
an allocation is used for an array. The main benefit over os_zalloc() is
in having an extra check to catch integer overflows in multiplication.
Signed-hostap: Jouni Malinen <j@w1.fi>
Multiple memcmps of nonces were actually comparing only the first byte
instead of all 16 bytes. [Bug 462]
Signed-hostap: Eyal Shapira <eyal@wizery.com>
intended-for: hostap-1
There is no need to mandate admission control (ACM=1) by default, so
clear that flag in the case the configuration file does not specify
wmm_ac_{vo,vi}_acm value. This gets closer to the values mentioned
in the sample hostapd.conf file and reduces the need to specify WMM
parameters in the configuration file for most common use cases.
Signed-hostap: Jouni Malinen <j@w1.fi>
p2p_set_timeout() calls in GO Neg Req/Resp TX callbacks used timeout of
100 ms which is the value given in the P2P specification for GO
Negotiation, but this was actually shorter than the
wait-for-offchannel-TX value (200 ms) used for the driver call. In
addition, it looks like some devices (e.g., Galaxy Nexus with JB image)
can take longer time to reply to GO Negotiation Response (somewhere
between 200 and 250 ms has been observed).
Increase the wait-for-GO-Neg-Resp timeout from 100 ms to 200 ms if GO
Negotiation Request frame was acknowledged (this matches with the
offchannel wait timeout that used previously). The no-ack case is left
at 100 ms since we use GO Negotiation Request frame also to discover
whether the peer is on its Listen channel.
Increase the wait-for-GO-Neg-Conf timeout from 100 ms to 250 ms (and
increase the offchannel wait timeout to matching 250 ms) as a workaround
for devices that take over 200 ms to reply to GO Negotiation Response.
Signed-hostap: Jouni Malinen <j@w1.fi>
The commit b5fd8b1833
"VHT: Do not allow use of TKIP with VHT" introduced
an off-by-one regression: a WPA/RSN 11n AP would no
longer accept stations to connect, instead it would
produce a bogus error message:
... Station tried to use TKIP with HT association.
Signed-hostapd: Christian Lamparter <chunkeey@googlemail.com>
cur_pmksa was left to NULL during the initial association. This can
result in unexpected behavior, e.g., in expiring PMKSA cache entries
since the current entry is not locked in that case. Fix this by updated
cur_pmksa when adding the initial PMKSA entry during msg 1/4 processing.
Signed-hostap: Jouni Malinen <j@w1.fi>
intended-for: hostap-1
If the PMKSA cache is full (i.e., 32 candidates have been seen in scan
results and have not yet expired) then any additional entries can
potentially evict the current/active entry (if it is the oldest entry),
which triggers a pointless local deauthentication. The supplicant
shouldn't replace the current/active entry if it is still valid, but
instead the oldest entry that is *not* the current/active one.
Signed-hostap: Dan Williams <dcbw@redhat.com>
intended-for: hostap-1
When using multiple VLANs, GKeyDoneStations counter is not updated
properly since wpa_auth_for_each_sta() call in wpa_group_setkeys() ends
up iterating through all STAs and not just the STAs of a specific
wpa_group (VLAN). Consequently, GTK rekeying gets initialized multiple
times if more than a single group state machine exists. Fix this by
iterating only through the STAs in the specific wpa_group.
Signed-hostap: Michael Braun <michael-dev@fami-braun.de>
intended-for: hostap-1
CONFIG_VLAN_NETLINK=y build option can now be used to replace the
ioctl()-based interface for creating and removing VLAN interfaces
with netlink-based interface.
Signed-hostap: M. Braun <michael-dev@fami-braun.de>
Commit a11241fa11 removed the 802.11b rate
enabling/disabling code from wpa_driver_nl80211_set_mode() and while
doing that, removed the only place where drv->disabled_11b_rates was
set. Fix this by updating the flag in nl80211_disable_11b_rates(). In
addition, re-enable the 802.11b rates when changing to non-P2P mode.
Signed-hostap: Jouni Malinen <j@w1.fi>
Right now 11b rates are masked out while creating a P2P interface,
but this is always failing as the interface is down. Most drivers
allow to configure rates only when the interface is UP and running.
So let us disable 11b rates when interface type is changed into a
P2P type and it is UP and running.
Signed-hostap: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
These validation steps are already done in the EAP parsing code and in
the EAP methods, but the additional check is defensive programming and
can make the validation of received EAP messages more easier to
understand.
Signed-hostap: Jouni Malinen <j@w1.fi>
These checks would not really be needed since eapol_sm_rx_eapol()
validates the length fields. Anyway, these makes it more obvious to
anyone reviewing the code that there are no integer underflow issues in
processKey().
Signed-hostap: Jouni Malinen <j@w1.fi>
These checks would not really be needed since radius_msg_parse()
validates the attribute header fields. Anyway, these makes it more
obvious to anyone reviewing the code that there are no integer underflow
issues in the functions processing RADIUS attributes.
Signed-hostap: Jouni Malinen <j@w1.fi>
This simplifies the implementation by using the buffer type to which the
returned data will be converted anyway. This avoids one memory
allocation for each processed RADIUS message.
Signed-hostap: Jouni Malinen <j@w1.fi>
Couple of functions did not verify that nla_put_nested() succeeded. Fix
these by checking the return value and handling error cases cleanly.
Signed-hostap: Jouni Malinen <j@w1.fi>
The new ssid2 parameter can be used as an alternative mechanism for
configuring SSID for hostapd. It uses the same formats that
wpa_supplicant uses in the configuration file for strings.
Signed-hostap: Jouni Malinen <j@w1.fi>
Instead of masking out non-ASCII characters with underscores, espace the
SSID data using rules compatible with printf.
Signed-hostap: Jouni Malinen <j@w1.fi>
This can be used to build ASCII strings from binary data that is
more likely to use ASCII (i.e., text format is more natural
option than hexdump, but there is possibility of some non-ASCII
characters).
Signed-hostap: Jouni Malinen <j@w1.fi>
When CONFIG_CTRL_IFACE=udp-remote is used, print user frendly PS in
wpa_cli. E.g.,
localhost/wlan0>
192.168.1.1/p2p-wlan-0-0>
Signed-hostap: Janusz Dziedzic <janusz.dziedzic@tieto.com>
wpa_cli can be used now as a client for remote access to ctrl_interface
of wpa_supplicant when UDP and remote options are used.
You can simply run:
wpa_cli -i <hostname>:[port]
wpa_cli -i <IP>:[port]
Signed-hostap: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Add new option for ctrl iface: CONFIG_CTRL_IFACE=udp-remote. This
enables remote access to control interface via UDP port(s). This should
be used for testing purpose only since there is no authentication or
access control on the commands.
Signed-hostap: Janusz Dziedzic <janusz.dziedzic@tieto.com>
This bit is set in the code path that handles keys and certs from places
other than OpenSSL authentication engines. Setting this bit causes
authentication to fail when the server provides certificates that don't
match the client certificate authority.
Commit 05ab9712b9 added support for
fetching WPA PSK from an external RADIUS server and changed
hostapd_wpa_auth_get_psk() to always return the RADIUS supplied PSK (if
set) and ignore the prev_psk parameter for iteration. Fix this by
appending the RADIUS supplied PSK to the list iterated by
hostapd_get_psk and thus returning NULL when prev_psk == sta->psk
(RADIUS).
Signed-hostap: M. Braun <michael-dev@fami-braun.de>
This allows the password parameter for EAP methods to be fetched
from an external storage.
Following example can be used for developer testing:
ext_password_backend=test:pw1=password|pw2=testing
network={
key_mgmt=WPA-EAP
eap=TTLS
identity="user"
password=ext:pw1
ca_cert="ca.pem"
phase2="auth=PAP"
}
Signed-hostap: Jouni Malinen <j@w1.fi>
This new mechanism can be used to make wpa_supplicant using external
storage (e.g., key store in the operating system) for passwords,
passphrases, and PSKs. This commit is only adding the framework part
needed to support this, i.e., no actual configuration parameter can
yet use this new mechanism. In addition, only a simple test backend
is added to allow developer testing of the functionality.
Signed-hostap: Jouni Malinen <j@w1.fi>
This allows the SA Query mechanism in hostapd to be used with drivers
that implement authentication and association MLME/SME.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
disable_dgaf=1 in hostapd.conf can now be used to disable downstream
group-addressed forwarding (DGAF). In this configuration, a unique
GTK (and IGTK) is provided to each STA in the BSS to make sure the
keys do not match and no STA can forge group-addressed frames.
An additional mechanism in the AP needs to be provided to handle some
group-addressed frames, e.g., by converting DHCP packets to unicast
IEEE 802.11 frames regardless of their destination IP address and by
providing Proxy ARP functionality.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Allow the user to configure an RSSI threshold in dBm below which the
nl80211 driver won't report scan results. Currently only supported
during scheduled (PNO) scans.
Signed-off-by: Thomas Pedersen <c_tpeder@qca.qualcomm.com>
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Commit 6b56cc2d97 added retries of
provision discovery request frames in IDLE state. However, it did not
make the p2p_find case behave consistently with the new limitied retry
behavior. This can result in way too many and frequent PD retries. Fix
this by extending the previous commit to address PD retries and maximum
retry limit consistently regardless of whether p2p_find is running.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
intended-for: hostap-1
Commit 1b487b8b1e added CH_SWITCH
event for nl80211, but ended up using hostapd_hw_get_channel()
regardless of build configuration for driver interfaces. This
function is not always available, so make its use conditional
on NEED_AP_MLME.
Signed-hostap: Jouni Malinen <j@w1.fi>
