mirror of
https://github.com/vanhoefm/fragattacks.git
synced 2024-11-25 08:48:31 -05:00
6c2f70cc6a
These parameter use hexdump values over the control interface, so mention them in the DPP example documentation. Signed-off-by: Jouni Malinen <j@w1.fi>
196 lines
5.4 KiB
Plaintext
196 lines
5.4 KiB
Plaintext
Device Provisioning Protocol (DPP)
|
|
==================================
|
|
|
|
This document describes how the Device Provisioning Protocol (DPP)
|
|
implementation in wpa_supplicant and hostapd can be configured and how
|
|
the STA device and AP can be configured to connect each other using DPP
|
|
Connector mechanism.
|
|
|
|
Introduction to DPP
|
|
-------------------
|
|
|
|
Device provisioning Protocol allows enrolling of interface-less devices
|
|
in a secure Wi-Fi network using many methods like QR code based
|
|
authentication( detailed below ), PKEX based authentication etc. In DPP
|
|
a Configurator is used to provide network credentials to the devices.
|
|
The three phases of DPP connection are authentication, configuration and
|
|
network introduction.
|
|
|
|
Build config setup
|
|
------------------
|
|
|
|
The following changes must go in the config file used to compile hostapd
|
|
and wpa_supplicant.
|
|
|
|
wpa_supplicant build config
|
|
---------------------------
|
|
|
|
Enable DPP and protected management frame in wpa_supplicant build config
|
|
file
|
|
|
|
CONFIG_DPP=y
|
|
|
|
hostapd build config
|
|
--------------------
|
|
|
|
Enable DPP and protected management frame in hostapd build config file
|
|
|
|
CONFIG_DPP=y
|
|
|
|
Configurator build config
|
|
-------------------------
|
|
|
|
Any STA or AP device can act as a Configurator. Enable DPP and protected
|
|
managment frames in build config. For an AP to act as Configurator,
|
|
Interworking needs to be enabled. For wpa_supplicant it is not required.
|
|
|
|
CONFIG_INTERWORKING=y
|
|
|
|
|
|
Sample supplicant config file before provisioning
|
|
-------------------------------------------------
|
|
|
|
ctrl_interface=DIR=/var/run/wpa_supplicant
|
|
ctrl_interface_group=0
|
|
update_config=1
|
|
pmf=2
|
|
dpp_config_processing=2
|
|
|
|
Sample hostapd config file before provisioning
|
|
----------------------------------------------
|
|
|
|
interface=wlan0
|
|
driver=nl80211
|
|
ctrl_interface=/var/run/hostapd
|
|
ssid=test
|
|
channel=1
|
|
wpa=2
|
|
wpa_key_mgmt=DPP
|
|
ieee80211w=1
|
|
wpa_pairwise=CCMP
|
|
rsn_pairwise=CCMP
|
|
|
|
|
|
Pre-requisites
|
|
--------------
|
|
|
|
It is assumed that an AP and client station are up by running hostapd
|
|
and wpa_supplicant using respective config files.
|
|
|
|
|
|
Creating Configurator
|
|
---------------------
|
|
|
|
Add a Configurator over the control interface (wpa_cli/hostapd_cli)
|
|
|
|
> dpp_configurator_add
|
|
(returns id)
|
|
|
|
To get key of Configurator
|
|
> dpp_configurator_get_key <id>
|
|
|
|
|
|
How to configure an enrollee using Configurator
|
|
-----------------------------------------------
|
|
|
|
On enrollee side:
|
|
|
|
Generate QR code for the device. Store the qr code id returned by the
|
|
command.
|
|
|
|
> dpp_bootstrap_gen type=qrcode mac=<mac-address-of-device> chan=<operating-class/operating-channel> key=<key of the device>
|
|
(returns bootstrapping info id)
|
|
|
|
Get QR Code of device using the bootstrap info id.
|
|
> dpp_bootstrap_get_uri <bootstrap-id>
|
|
|
|
Make device listen to DPP request (The central frequency of channel 1 is
|
|
2412) in case if enrollee is a client device.
|
|
|
|
> dpp_listen <frequency>
|
|
|
|
On Configurator side:
|
|
|
|
Enter the QR Code in the Configurator.
|
|
> dpp_qr_code "<QR-Code-read-from-enrollee>"
|
|
|
|
On successfully adding QR Code, a bootstrapping info id is returned.
|
|
|
|
Send provisioning request to enrollee. (conf is ap-dpp if enrollee is an
|
|
AP. conf is sta-dpp if enrollee is a client)
|
|
> dpp_auth_init peer=<qr-code-id> conf=<ap-dpp|sta-dpp> ssid=<SSID hexdump> configurator=<configurator-id>
|
|
or for legacy (PSK/SAE) provisioning for a station Enrollee:
|
|
> dpp_auth_init peer=<qr-code-id> conf=sta-psk ssid=<SSID hexdump> pass=<passphrase hexdump>
|
|
|
|
The DPP values will be printed in the console. Save this values into the
|
|
config file. If the enrollee is an AP, we need to manually write these
|
|
values to the hostapd config file. If the enrollee is a client device,
|
|
these details can be automatically saved to config file using the
|
|
following command.
|
|
|
|
> save_config
|
|
|
|
To set values in runtime for AP enrollees
|
|
|
|
> set dpp_connector <Connector-value-printed-on-console>
|
|
> set dpp_csign <csign-value-on-console>
|
|
> set dpp_netaccesskey <netaccess-value-on-console>
|
|
|
|
To set values in runtime for client enrollees, set dpp_config_processing
|
|
to 2 in wpa_supplicant conf file.
|
|
|
|
Once the values are set in run-time (if not set in run-time, but saved
|
|
in config files, they are taken up in next restart), the client device
|
|
will automatically connect to the already provisioned AP and connection
|
|
will be established.
|
|
|
|
|
|
Self-configuring a device
|
|
-------------------------
|
|
|
|
It is possible for a device to configure itself if it is the
|
|
Configurator for the network.
|
|
|
|
Create a Configurator in the device and use the dpp_configurator_sign
|
|
command to get DPP credentials.
|
|
|
|
> dpp_configurator_add
|
|
(returns configurator id)
|
|
> dpp_configurator_sign conf=<ap-dpp|sta-dpp> configurator=<configurator-id>
|
|
|
|
|
|
Sample AP configuration files after provisioning
|
|
------------------------------------------------
|
|
|
|
interface=wlan0
|
|
driver=nl80211
|
|
ctrl_interface=/var/run/hostapd
|
|
ssid=test
|
|
channel=1
|
|
wpa=2
|
|
wpa_key_mgmt=DPP
|
|
ieee80211w=1
|
|
wpa_pairwise=CCMP
|
|
rsn_pairwise=CCMP
|
|
dpp_connector=<Connector value provided by Configurator>
|
|
dpp_csign=<C-Sign-Key value provided by Configurator>
|
|
dpp_netaccesskey=<Net access key provided by Configurator>
|
|
|
|
|
|
Sample station configuration file after provisioning
|
|
----------------------------------------------------
|
|
|
|
ctrl_interface=DIR=/var/run/wpa_supplicant
|
|
ctrl_interface_group=0
|
|
update_config=1
|
|
pmf=2
|
|
dpp_config_processing=2
|
|
network={
|
|
ssid="test"
|
|
key_mgmt=DPP
|
|
ieee80211w=2
|
|
dpp_connector="<Connector value provided by Configurator>"
|
|
dpp_netaccesskey=<Net access key provided by Configurator>
|
|
dpp_csign=<C-sign-key value provided by Configurator>
|
|
}
|