mirror of
https://github.com/vanhoefm/fragattacks.git
synced 2024-11-29 10:48:22 -05:00
9d7fdac5b3
It was possible for regulatory domain changes to "leak" into following test cases in number of cases where the cfg80211 BSS table remained after regulatory domain had been restored to world roaming. Try to make this less likely to occur by explicitly clearing BSS table at the end of test cases that use different regulatory domain. This makes P2P test cases that verify channel selection based on world roaming rules more robust. Signed-off-by: Jouni Malinen <j@w1.fi>
205 lines
6.9 KiB
Python
205 lines
6.9 KiB
Python
# Test cases for automatic channel selection with hostapd
|
|
# Copyright (c) 2013-2014, Jouni Malinen <j@w1.fi>
|
|
#
|
|
# This software may be distributed under the terms of the BSD license.
|
|
# See README for more details.
|
|
|
|
import logging
|
|
logger = logging.getLogger()
|
|
import subprocess
|
|
import time
|
|
|
|
import hostapd
|
|
|
|
def wait_acs(hapd):
|
|
ev = hapd.wait_event(["ACS-STARTED", "ACS-COMPLETED", "ACS-FAILED",
|
|
"AP-ENABLED", "AP-DISABLED"], timeout=5)
|
|
if not ev:
|
|
raise Exception("ACS start timed out")
|
|
if "ACS-STARTED" not in ev:
|
|
raise Exception("Unexpected ACS event: " + ev)
|
|
|
|
state = hapd.get_status_field("state")
|
|
if state != "ACS":
|
|
raise Exception("Unexpected interface state")
|
|
|
|
ev = hapd.wait_event(["ACS-COMPLETED", "ACS-FAILED", "AP-ENABLED",
|
|
"AP-DISABLED"], timeout=20)
|
|
if not ev:
|
|
raise Exception("ACS timed out")
|
|
if "ACS-COMPLETED" not in ev:
|
|
raise Exception("Unexpected ACS event: " + ev)
|
|
|
|
ev = hapd.wait_event(["AP-ENABLED", "AP-DISABLED"], timeout=5)
|
|
if not ev:
|
|
raise Exception("AP setup timed out")
|
|
if "AP-ENABLED" not in ev:
|
|
raise Exception("Unexpected ACS event: " + ev)
|
|
|
|
state = hapd.get_status_field("state")
|
|
if state != "ENABLED":
|
|
raise Exception("Unexpected interface state")
|
|
|
|
def test_ap_acs(dev, apdev):
|
|
"""Automatic channel selection"""
|
|
params = hostapd.wpa2_params(ssid="test-acs", passphrase="12345678")
|
|
params['channel'] = '0'
|
|
hapd = hostapd.add_ap(apdev[0]['ifname'], params, wait_enabled=False)
|
|
wait_acs(hapd)
|
|
|
|
freq = hapd.get_status_field("freq")
|
|
if int(freq) < 2400:
|
|
raise Exception("Unexpected frequency")
|
|
|
|
dev[0].connect("test-acs", psk="12345678", scan_freq=freq)
|
|
|
|
def test_ap_multi_bss_acs(dev, apdev):
|
|
"""hostapd start with a multi-BSS configuration file using ACS"""
|
|
ifname = apdev[0]['ifname']
|
|
|
|
# make sure the current channel is on 2.4 GHz band as a workaround for the
|
|
# limited survey functionality in mac80211_hwsim
|
|
hostapd.add_ap(ifname, { "ssid": "test" })
|
|
time.sleep(0.1)
|
|
hapd_global = hostapd.HostapdGlobal()
|
|
hapd_global.remove(ifname)
|
|
|
|
# start the actual test
|
|
hostapd.add_iface(ifname, 'multi-bss-acs.conf')
|
|
hapd = hostapd.Hostapd(ifname)
|
|
hapd.enable()
|
|
wait_acs(hapd)
|
|
|
|
freq = hapd.get_status_field("freq")
|
|
if int(freq) < 2400:
|
|
raise Exception("Unexpected frequency")
|
|
|
|
dev[0].connect("bss-1", key_mgmt="NONE", scan_freq=freq)
|
|
dev[1].connect("bss-2", psk="12345678", scan_freq=freq)
|
|
dev[2].connect("bss-3", psk="qwertyuiop", scan_freq=freq)
|
|
|
|
def test_ap_acs_40mhz(dev, apdev):
|
|
"""Automatic channel selection for 40 MHz channel"""
|
|
params = hostapd.wpa2_params(ssid="test-acs", passphrase="12345678")
|
|
params['channel'] = '0'
|
|
params['ht_capab'] = '[HT40+]'
|
|
hapd = hostapd.add_ap(apdev[0]['ifname'], params, wait_enabled=False)
|
|
wait_acs(hapd)
|
|
|
|
freq = hapd.get_status_field("freq")
|
|
if int(freq) < 2400:
|
|
raise Exception("Unexpected frequency")
|
|
sec = hapd.get_status_field("secondary_channel")
|
|
if int(sec) == 0:
|
|
raise Exception("Secondary channel not set")
|
|
|
|
dev[0].connect("test-acs", psk="12345678", scan_freq=freq)
|
|
|
|
def test_ap_acs_5ghz(dev, apdev):
|
|
"""Automatic channel selection on 5 GHz"""
|
|
try:
|
|
hapd = None
|
|
params = hostapd.wpa2_params(ssid="test-acs", passphrase="12345678")
|
|
params['hw_mode'] = 'a'
|
|
params['channel'] = '0'
|
|
params['country_code'] = 'US'
|
|
hapd = hostapd.add_ap(apdev[0]['ifname'], params, wait_enabled=False)
|
|
# TODO: Remove exception acceptance once mac80211_hwsim supports ACS on
|
|
# 5 GHz
|
|
run = False
|
|
try:
|
|
wait_acs(hapd)
|
|
run = True
|
|
except Exception, e:
|
|
logger.info("Ignore exception due to missing hwsim support: " + str(e))
|
|
|
|
if run:
|
|
freq = hapd.get_status_field("freq")
|
|
if int(freq) < 5000:
|
|
raise Exception("Unexpected frequency")
|
|
|
|
dev[0].connect("test-acs", psk="12345678", scan_freq=freq)
|
|
|
|
finally:
|
|
dev[0].request("DISCONNECT")
|
|
if hapd:
|
|
hapd.request("DISABLE")
|
|
subprocess.call(['sudo', 'iw', 'reg', 'set', '00'])
|
|
dev[0].flush_scan_cache()
|
|
|
|
def test_ap_acs_5ghz_40mhz(dev, apdev):
|
|
"""Automatic channel selection on 5 GHz for 40 MHz channel"""
|
|
try:
|
|
hapd = None
|
|
params = hostapd.wpa2_params(ssid="test-acs", passphrase="12345678")
|
|
params['hw_mode'] = 'a'
|
|
params['channel'] = '0'
|
|
params['ht_capab'] = '[HT40+]'
|
|
params['country_code'] = 'US'
|
|
hapd = hostapd.add_ap(apdev[0]['ifname'], params, wait_enabled=False)
|
|
# TODO: Remove exception acceptance once mac80211_hwsim supports ACS on
|
|
# 5 GHz
|
|
run = False
|
|
try:
|
|
wait_acs(hapd)
|
|
run = True
|
|
except Exception, e:
|
|
logger.info("Ignore exception due to missing hwsim support: " + str(e))
|
|
|
|
if run:
|
|
freq = hapd.get_status_field("freq")
|
|
if int(freq) < 5000:
|
|
raise Exception("Unexpected frequency")
|
|
|
|
sec = hapd.get_status_field("secondary_channel")
|
|
if int(sec) == 0:
|
|
raise Exception("Secondary channel not set")
|
|
|
|
dev[0].connect("test-acs", psk="12345678", scan_freq=freq)
|
|
|
|
finally:
|
|
dev[0].request("DISCONNECT")
|
|
if hapd:
|
|
hapd.request("DISABLE")
|
|
subprocess.call(['sudo', 'iw', 'reg', 'set', '00'])
|
|
dev[0].flush_scan_cache()
|
|
|
|
def test_ap_acs_vht(dev, apdev):
|
|
"""Automatic channel selection for VHT"""
|
|
try:
|
|
hapd = None
|
|
params = hostapd.wpa2_params(ssid="test-acs", passphrase="12345678")
|
|
params['hw_mode'] = 'a'
|
|
params['channel'] = '0'
|
|
params['ht_capab'] = '[HT40+]'
|
|
params['country_code'] = 'US'
|
|
params['ieee80211ac'] = '1'
|
|
params['vht_oper_chwidth'] = '1'
|
|
hapd = hostapd.add_ap(apdev[0]['ifname'], params, wait_enabled=False)
|
|
# TODO: Remove exception acceptance once mac80211_hwsim supports ACS on
|
|
# 5 GHz
|
|
run = False
|
|
try:
|
|
wait_acs(hapd)
|
|
run = True
|
|
except Exception, e:
|
|
logger.info("Ignore exception due to missing hwsim support: " + str(e))
|
|
|
|
if run:
|
|
freq = hapd.get_status_field("freq")
|
|
if int(freq) < 5000:
|
|
raise Exception("Unexpected frequency")
|
|
|
|
sec = hapd.get_status_field("secondary_channel")
|
|
if int(sec) == 0:
|
|
raise Exception("Secondary channel not set")
|
|
|
|
dev[0].connect("test-acs", psk="12345678", scan_freq=freq)
|
|
|
|
finally:
|
|
dev[0].request("DISCONNECT")
|
|
if hapd:
|
|
hapd.request("DISABLE")
|
|
subprocess.call(['sudo', 'iw', 'reg', 'set', '00'])
|
|
dev[0].flush_scan_cache()
|