CA country code was included mistakenly (copy-paste..) in cn_op_class_cc
while it was supposed to be included only in us_op_class_cc. In
practice, this did not result in incorrect operation due to the
us_op_class_cc list being checked first. Anyway, better fix
cn_op_class_cc to avoid confusion here.
Signed-off-by: Jouni Malinen <j@w1.fi>
Add operating class 125 (channels 149..169) to the list of P2P supported
channels. This allows the 5 GHz channels 161 and 169 to be used for P2P
GO when those channels are allowed for AP mode in the current regulatory
domain.
Signed-off-by: Amr BEN ABDESSALEM <amrx.ben.abdessalem@intel.com>
By analysing objdump output some read only structures were found in
.data section. To help compiler further optimize code declare these
as const.
Signed-off-by: Mikael Kanstrup <mikael.kanstrup@sonymobile.com>
Check the element length in the parser and remove the length field from
struct ieee802_11_elems since the element is of fixed length.
Signed-off-by: Jouni Malinen <j@w1.fi>
Check the element length in the parser and remove the length field from
struct ieee802_11_elems since the element is of fixed length.
Signed-off-by: Jouni Malinen <j@w1.fi>
Check the element length in the parser and remove the length field from
struct ieee802_11_elems since the element is of fixed length.
Signed-off-by: Jouni Malinen <j@w1.fi>
Check the element length in the parser and remove the length field from
struct ieee802_11_elems since the element is of fixed length.
Signed-off-by: Jouni Malinen <j@w1.fi>
Remove the length field from struct ieee802_11_elems since the only
allowed element length is five and that is checked by the parser.
Signed-off-by: Jouni Malinen <j@w1.fi>
Check the element length in the parser and remove the length field from
struct ieee802_11_elems since the only allowed element length is one.
Signed-off-by: Jouni Malinen <j@w1.fi>
Check the element length in the parser and remove the length field from
struct ieee802_11_elems since the only allowed element length is one.
Signed-off-by: Jouni Malinen <j@w1.fi>
All the existing users of these elements were already validating the
element length. However, it is clearer to validate this already at the
parser for extra layer of protection for any future changes.
Signed-off-by: Jouni Malinen <j@w1.fi>
The SSID element is defined to have a valid length range of 0-32. While
this length was supposed to validated by the users of the element
parser, there are not really any valid cases where the maximum length of
32 octet SSID would be exceeded and as such, the parser itself can
enforce the limit as an additional protection.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add handling logic for DFS offloaded case, and add a helper function
that takes the frequency (MHz) as a param and returns 1 if given channel
requires DFS, or 0 otherwise.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This allows vendor specific information element to be used to advertise
support for VHT on 2.4 GHz band. In practice, this is used to enable use
of 256 QAM rates (VHT-MCS 8 and 9) on 2.4 GHz band.
This functionality is disabled by default, but can be enabled with
vendor_vht=1 parameter in hostapd.conf if the driver advertises support
for VHT on either 2.4 or 5 GHz bands.
Signed-off-by: Yanbo Li <yanbol@qti.qualcomm.com>
ieee80211_chan_to_freq() is a generic function that replaces and extends
the previous P2P-specific p2p_channel_to_freq(). The new function
supports both the global operating class table as well as the additional
US, EU, JP, and CN operating class tables.
Signed-off-by: Jouni Malinen <j@w1.fi>
These information elements are not really used anywhere in hostapd or
wpa_supplicant nor is there any plan to use them. As such, there is no
need to keep the code here either, so save couple of bytes here.
Signed-hostap: Jouni Malinen <j@w1.fi>
Indicate support for QoS Mapping and configure driver to update the QoS
Map if QoS Map Set elements is received from the AP either in
(Re)Association Response or QoS Map Configure frame.
This commit adds support for receiving the frames with nl80211 drivers,
but the actual QoS Map configuration command is still missing.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
If AP mode SME/MLME within wpa_supplicant is used for processing Probe
Request frames in GO mode, drop Probe Request frames that include only
802.11b rates per P2P spec section 2.4.1.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This allows Probe Request frame processing to compare the configured
SSID to the SSID List element in addition to the SSID element.
Signed-hostap: Jouni Malinen <j@w1.fi>
This commit adds control interface commands and internal storage of
Wi-Fi Display related configuration. In addition, WFD IE is now added
to various P2P frames, Probe Request/Response, and (Re)Association
Request/Response frames. WFD subelements from peers are stored in the
P2P peer table.
Following control interface commands are now available:
SET wifi_display <0/1>
GET wifi_display
WFD_SUBELEM_SET <subelem> [hexdump of length+body]
WFD_SUBELEM_GET <subelem>
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
If WNM is enabled for the build (CONFIG_WNM=y), add BSS max idle period
information to the (Re)Association Response frame from the AP and parse
this information on the station. For SME-in-wpa_supplicant case, add a
timer to handle periodic transmission of the keep-alive frame. The
actual request for the driver to transmit a frame is not yet
implemented.
Signed-hostap: Jouni Malinen <j@w1.fi>
Some frequent debug prints are of limited use and make debug output
difficult to read. Make them use a new debug level so that -dd
provides more readable output (-ddd can now be used to enable
the excessive debug prints).
This adds first part of FT resource request as part of Reassocition
Request frame (i.e., FT Protocol, not FT Resource Request Protocol).
wpa_supplicant can generate a test resource request when driver_test.c
is used with internal MLME code and hostapd can verify the FTIE MIC
properly with the included RIC Request.
The actual RIC Request IEs are not processed yet and hostapd does not
yet reply with RIC Response (nor would wpa_supplicant be able to
validate the FTIE MIC for a frame with RIC Response).
This updates the terminogy to match with the final WMM specification. In
addition, some of the WMM TSPEC structure fields were in incorrect order
and used without byte order swapping. Those are also taken care of this
cleanup patch.
The separate Association Comeback Time IE was removed from IEEE 802.11w
and the Timeout Interval IE (from IEEE 802.11r) is used instead. The
editing on this is still somewhat incomplete in IEEE 802.11w/D7.0, but
still, the use of Timeout Interval IE is the expected mechanism.
This IE is not (at least yet) actually used for anything, but parsing it
cleans up verbose debug log a bit since thie previously unknown, but
commonly used, vendor IE was being reported as unknown.
This adds WPS support for both hostapd and wpa_supplicant. Both programs
can be configured to act as WPS Enrollee and Registrar. Both PBC and PIN
methods are supported.
Currently, hostapd has more complete configuration option for WPS
parameters and wpa_supplicant configuration style will likely change in
the future. External Registrars are not yet supported in hostapd or
wpa_supplicant. While wpa_supplicant has initial support for acting as
an Registrar to configure an AP, this is still using number of hardcoded
parameters which will need to be made configurable for proper operation.
