If CONFIG_WPS_TESTING=y is enabled in build configuration, the new
wps_corrupt_pkhash parameter (similar to wps_testing_dummy_cred) can be
used to request public key hash to be corrupted in all generated OOB
Device Password attributes. This can be used for testing purposes to
validate public key hash validation steps.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
"NFC_REPORT_HANDOVER {INIT,RESP} P2P <req> <sel>" can now be used to
report completed NFC negotiated connection handover in which the P2P
alternative carrier was selected.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The new Device Password ID 7 is used to indicate that NFC connection
handover is used with DH public key hash from both devices being
exchanged over the NFC connection handover messages. This allows an
abbreviated M1-M2 handshake to be used since Device Password does not
need to be used when DH is authenticated with the out-of-band
information (validation of the public key against the hash).
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Since the Enrollee can now get the public key hash from the Registrar,
there is need to validate this during the WPS protocol run.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
According to WSC specification (Ver 2.0.2, section 8.3), RF Bands
attribute should be set to the specific RF band used for the current
message. Add an option to set wanted band in wps_build_rf_bands() and
add a callback to get the current band from wpa_supplicant and hostapd.
Signed-hostap: David Spinadel <david.spinadel@intel.com>
Registrar is allowed to propose another Device Password ID in M2. Make
Enrollee validate Device Password ID in M2 to check if this happened.
This commit adds support for changing from NFC password token to default
PIN for the case where the AP is the Enrollee and has both the NFC
password token and AP PIN enabled at the same time.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The UFD (USB flash drive) configuration method was deprecated in WSC
2.0. Since this is not known to be used, remove the UFD implementation
from hostapd and wpa_supplicant to allow the WPS implementation to be
cleaned up. This removes the now unused OOB operations and ctrl_iface
commands that had already been deprecated by the new NFC operations.
Signed-hostap: Jouni Malinen <j@w1.fi>
Maintain state of WPS APs during iteration to find the correct AP for
WPS PIN operation when no specific BSSID is specified. This information
can be used for optimizing the order in which the APs are tried. This
commit is only adding the collection of the information and more
detailed debug information to make debug logs more helpful in figuring
out how the AP selection order could be improved.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The new hostapd ctrl_iface command WPS_NFC_TOKEN can now be used to
manage AP-as-Enrollee operations with NFC password token. WPS/NDEF
parameters to this command can be used to generate a new NFC password
token. enable/disable parameters can be used to enable/disable use of
NFC password token (instead of AP PIN) for external Registrars.
A preconfigured NFS password token can be used by providing its
parameters with new hostapd.conf fields wps_nfc_dev_pw_id,
wps_nfc_dh_pubkey, wps_nfc_dh_privkey, and wps_nfc_dev_pw. This use
will also depend on WPS_NFC_TOKEN enable/disable commands, i.e., the
configured NFS password token is disabled by default.
Signed-hostap: Jouni Malinen <j@w1.fi>
This adds a cleaner mechanism for handling NFC Password Tokens in the
WPS Registrar. There could be more than one active NFC Password Token in
use and as such, a list of tokens needs to be maintained. The old
WPS_OOB interface is still using the old mechanism that supports only a
single active NFC Password Token.
Signed-hostap: Jouni Malinen <j@w1.fi>
Use Device Password ID in WSC IE of Probe Request and Probe Response
frames to advertise immediate availability of WPS credentials per P2P
specification sections 3.1.2.1.1 (Listen State), 3.1.2.1.2 (Scan Phase),
and 3.1.2.1.3 (Find Phase).
For now, the Device Password ID is set only for the case where we are
active GO Negotiation with a specific peer. In practice, this means that
the Probe Response frames during pending GO Negotiation (whenever in
Listen state) indicate availability of the credential.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Some static analyzers complain about memset with '0' value. This was
used correctly here, but since use of strdup is about as good an option,
use that to silence the invalid warnings.
Signed-hostap: Jouni Malinen <j@w1.fi>
Instead of hardcoding the Config Methods attribute value in Probe
Request frames, set this based on the configured parameter
config_methods to allow correct set of methods to be advertised.
Extend the code that waits for the station to send EAPOL-Start before
initiating EAPOL authenticator operations to cover the case where the
station includes WPS IE in (Re)Association Request frame if that IE
does not include support for WPS 2.0. While this should not really
be needed, this may help with some deployed WPS 1.0 stations that do
not support EAPOL operations correctly and may get confused of the
EAP-Request/Identity packets that would show up twice if EAPOL-Start
is transmitted.
Windows 7 uses incorrect way of figuring out AP's WPS capabilities by
acting as a Registrar and using M1 from the AP. The config methods
attribute in that message is supposed to indicate only the configuration
method supported by the AP in Enrollee role, i.e., to add an external
Registrar. For that case, PBC shall not be used and as such, the
PushButton config method is removed from M1 by default. If pbc_in_m1=1
is included in the configuration file, the PushButton config method is
left in M1 (if included in config_methods parameter) to allow Windows 7
to use PBC instead of PIN (e.g., from a label in the AP).
The secondary device type list is an optional attribute in the WSC IE.
Signed-off-by: Jean-Michel Bachot <jean-michelx.bachot@linux.intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
An optional parameter, p2p_dev_addr, can now be given to WPS_PBC
command on P2P GO to indicate that only the P2P device with the
specified P2P Device Address is allowed to connect using PBC. If
any other device tries to use PBC, a session overlap is indicated
and the negotiation is rejected with M2D. The command format for
specifying the address is "WPS_PBC p2p_dev_addr=<address>", e.g.,
WPS_PBC p2p_dev_addr=02:03:04:05:06:07
In addition, show the PBC session overlap indication as a WPS failure
event on an AP/GO interface. This particular new case shows up as
"WPS-FAIL msg=4 config_error=12".
Instead of build time options (CONFIG_WPS_TESTING_EXTRA_CRED and
CONFIG_WPS_EXTENSIBILITY_TESTING), use a single build option
(CONFIG_WPS_TESTING) and runtime configuration of which testing
operations are enabled. This allows a single binary to be used
for various tests.
The runtime configuration can be done through control interface
with wpa_cli/hostapd_cli commands:
Enable extensibility tests:
set wps_version_number 0x57
Disable extensibility tests (WPS2 build):
set wps_version_number 0x20
Enable extra credential tests:
set wps_testing_dummy_cred 1
Disable extra credential tests:
set wps_testing_dummy_cred 0
The WSC 2.0 specification moved to use another design for the new
attributes to avoid backwards compatibility issues with some
deployed implementations.
If all the device information attributes use their maximum lengths,
a single WPS IE is not enough to fit in all the data and as such,
we must be able to fragment the data. In addition, the wpabuf needs
to be allocated larger to fit in maximum data.
Whenever wpa_supplication is using Request Type Enrollee, it is trying
to enroll into a network. Indicate this with the explicit inclusion of
Request to Enroll attribute with value TRUE.
Advertize list of authorized enrollee MAC addresses in Beacon and
Probe Response frames and use these when selecting the AP. In order
to provide the list, the enrollee MAC address should be specified
whenever adding a new PIN. In addition, add UUID-R into
SetSelectedRegistrar action to make it potentially easier for an AP
to figure out which ER sent the action should there be multiple ERs
using the same IP address.
This adds definitions and parsing of the new attributes that were added
in WPS 2.0. In addition, the version negotiation is updated to use the
new mechanism, i.e., accept everything received and use the new Version2
attribute in transmitted messages.
The AP configuration may change after provisioning, so it is better
not to use the current security policy to prioritize results. Instead,
use WPS Selected Registrar attribute as the main sorting key and use
signal strength next without considering security policy or rate sets.
The non-WPS provisioning case remains as-is, i.e., this change applies
only when trying to find an AP for WPS provisioning.
If the associating station indicates that it is intents to use WPS
by including WPS IE in (Re)Association Request frame, include WPS IE
in (Re)Association Response frame.
The use_psk_key parameter can now be used to force the Registrar to
use PSK format instead of ASCII passphrase when building a Credential
for the Enrollee. For now, this is not enabled, but it could be enabled
either based on external (to WPS) configuration or automatically set
based on some WPS attribute values from the Enrollee.
In addition, start ordering header file includes to be in more
consistent order: system header files, src/utils, src/*, same
directory as the *.c file.
This makes it clearer which files are including header from src/common.
Some of these cases should probably be cleaned up in the future not to
do that.
In addition, src/common/nl80211_copy.h and wireless_copy.h were moved
into src/drivers since they are only used by driver wrappers and do not
need to live in src/common.
Crypto library wrappers can now override the internal DH (group 5)
implementation. As a starting point, this is done with OpenSSL. The
new mechanism is currently available only for WPS (i.e., IKEv2 still
depends on the internal DH implementation).
Store a copy of device attributes during WPS protocol run and make it
available for external programs via the control interface STA MIB
command for associated stations. This gives access to device name and
type which can be useful when showing user information about associated
stations.
wpa_supplicant can now reconfigure the AP by acting as an External
Registrar with the wps_reg command. Previously, this was only used
to fetch the current AP settings, but now the wps_reg command has
optional arguments which can be used to provide the new AP
configuration. When the new parameters are set, the WPS protocol run
is allowed to continue through M8 to reconfigure the AP instead of
stopping at M7.
The new file wps_nfc.c and ndef.c implements NFC device independent
operation, wps_nfc_pn531.c implements NFC device dependent operation.
This patch is only for the following use case:
- Enrollee = wpa_supplicant
- Registrar = hostapd internal Registrar
Following NFC methods can be used:
- Enrollee PIN with NFC
- Registrar PIN with NFC
- unencrypted credential with NFC
Encrypted credentials are not supported.
Enrollee side operation:
Registrar side operation:
Example configuration.
CONFIG_WPS=y
CONFIG_WPS_NFC=y
CONFIG_WPS_NFC_PN531=y
I used NFC device "NXP PN531". The NFC device access method is
confidential, so I used outer library. Please download below files from
https://www.saice-wpsnfc.bz/index.php
[WPS NFC Library]
WpsNfcLibrary/WpsNfc.h
WpsNfcLibrary/WpsNfcType.h
WpsNfcLibrary/WpsNfcVersion.h
WpsNfcLibrary/linux/libnfc_mapping_pn53x.dll
WpsNfcLibrary/linux/wpsnfc.dll
[NFC Reader/Writer Kernel Driver]
NFCKernelDriver-1.0.3/linux/kobj/sonyrw.ko
<WiFi test>
The hostapd/wpa_supplicant with this patch passed below tests on
"Wi-Fi WPS Test Plan Version 1.6".
4.2.5 Add device using NFC Method with password token
(I used SONY STA instead of NXP STA.)
4.2.6 Add device using NFC Method with configuration token
5.1.9 Add to AP using NFC Method with password token
through internal registrar
(I used SONY AP instead of NXP AP.)
5.1.10 Add to AP using NFC Method with configuration token
through internal registrar
Not all embedded devices have USB interface and it is useful to be able
to remove unneeded functionality from the binary. In addition, the
current implementation has some UNIX specific calls in it which may make
it not compile cleanly on all target systems.
