Advertize list of authorized enrollee MAC addresses in Beacon and
Probe Response frames and use these when selecting the AP. In order
to provide the list, the enrollee MAC address should be specified
whenever adding a new PIN. In addition, add UUID-R into
SetSelectedRegistrar action to make it potentially easier for an AP
to figure out which ER sent the action should there be multiple ERs
using the same IP address.
This works around issues with EAP-Failure getting lost for some reason.
Instead of waiting up to 60 seconds on a timeout, 30 second timeout is
now used and whenever the provisioning step has been completed (either
successfully or unsuccessfully), this timeout is reduced to 2 seconds.
wpa_supplicant can now reconfigure the AP by acting as an External
Registrar with the wps_reg command. Previously, this was only used
to fetch the current AP settings, but now the wps_reg command has
optional arguments which can be used to provide the new AP
configuration. When the new parameters are set, the WPS protocol run
is allowed to continue through M8 to reconfigure the AP instead of
stopping at M7.
hostapd_cli wps_pin command can now have an optional timeout
parameter that sets the PIN lifetime in seconds. This can be used
to reduce the likelihood of someone else using the PIN should an
active PIN be left in the Registrar.
This adds mostly feature complete external Registrar support with the
main missing part being proper support for multiple external Registrars
working at the same time and processing of concurrent registrations when
using an external Registrar.
This code is based on Sony/Saice implementation
(https://www.saice-wpsnfc.bz/) and the changes made by Ted Merrill
(Atheros) to make it more suitable for hostapd design and embedded
systems. Some of the UPnP code is based on Intel's libupnp. Copyrights
and licensing are explained in src/wps/wps_upnp.c in more detail.
We need to be a bit more careful when removing the WPS configuration
block since wpa_s->current_ssid may still be pointing at it. In
addition, registrar pointer in wps_context will need to be cleared
since the context data is now maintained over multiple EAP-WSC runs.
Without this, certain WPS operations could have used freed memory.
The wps_context data is now managed at wpa_supplicant, not EAP-WSC. This
makes wpa_supplicant design for WPS match with hostapd one and also
makes it easier configure whatever parameters and callbacks are needed
for WPS.
Previously, wpa_supplicant as Enrollee case was handled using a
different callback function pointer. However, now that the wps_context
structure is allocated for all cases, the same variable can be used in
all cases.
Previously, hardcoded values were used in wps_enrollee.c. These are now
moved into shared data in struct wps_context. In case of
AP/Authenticator, these are initialized in wps_hostapd.c. In case of
client/supplicant, these are now initialized in EAP-WSC peer method,
but will probably end up being moved into higher layer for better
configuration.
EAP-WSC peer method for
The old (i.e., currently used) AP Settings are processed. For now, they
are copied as-is into M8 as new AP Settings to avoid changing
configuration. This should be changed to allow external programs (e.g.,
GUI) to fetch the old AP settings over ctrl_iface and then allow
settings to be changed before sending M8 with the new settings.
This adds WPS support for both hostapd and wpa_supplicant. Both programs
can be configured to act as WPS Enrollee and Registrar. Both PBC and PIN
methods are supported.
Currently, hostapd has more complete configuration option for WPS
parameters and wpa_supplicant configuration style will likely change in
the future. External Registrars are not yet supported in hostapd or
wpa_supplicant. While wpa_supplicant has initial support for acting as
an Registrar to configure an AP, this is still using number of hardcoded
parameters which will need to be made configurable for proper operation.
