hostapd_wpa_auth_conf() is called on uninitialized memory and the
conditional blocks in this function may leave some fields into
uninitialized state. This can result in unexpected behavior elsewhere
since some of the variables may be used without matching #ifdef
blocks. Fix this by zeroing the memory.
A new hostapd configuration parameter, disable_pmksa_caching=1, can now
be used to disable PMKSA caching on the Authenticator. This forces the
stations to complete EAP authentication on every association when WPA2
is being used.
This should fix EAPOL reauthentication and rekeying timeout issues
with Intel clients when using WMM (e.g., with IEEE 802.11n). These
stations do not seem to be able to handle EAPOL data frames as
non-QoS Data frames after the initial setup.
This adds STA flags to hapd_send_eapol() driver op to allow
driver_nl80211.c to mark the EAPOL frames as QoS Data frame
when injecting it through the monitor interface.
Some deployed supplicants update their SNonce for every receive
EAPOL-Key message 1/4 even when these messages happen during the
same 4-way handshake. Furthermore, some of these supplicants fail
to use the first SNonce that they sent and derive an incorrect PTK
using another SNonce that does not match with what the authenticator
is using from the first received message 2/4. This results in
failed 4-way handshake whenever the EAPOL-Key 1/4 retransmission
timeout is reached. The timeout for the first retry is fixed to
100 ms in the IEEE 802.11 standard and that seems to be short
enough to make it difficult for some stations to get the response
out before retransmission.
Work around this issue by increasing the initial EAPOL-Key 1/4
timeout by 1000 ms (i.e., total timeout of 1100 ms) if the station
acknowledges reception of the EAPOL-Key frame. If the driver does
not indicate TX status for EAPOL frames, use longer initial
timeout (1000 ms) unconditionally.
Use l2_packet with Ethernet header included so that the source
address for RRB packets can be forced to be the local BSSID. This
fixes problems where unexpected bridge interface address may end
up getting used and the recipient of the frame dropping it as
unknown R0KH/R1KH.
send_eapol, set_key, read_sta_data, sta_clear_stats,
set_radius_acl_auth, set_radius_acl_expire, and set_beacon
to use inline functions instead of extra abstraction.
Commit bf65bc638f started the path to
add this new abstraction for driver operations in AP mode to allow
wpa_supplicant to control AP mode operations. At that point, the
extra abstraction was needed, but it is not needed anymore since
hostapd and wpa_supplicant share the same struct wpa_driver_ops.
Start removing the unneeded abstraction by converting
send_mgmt_frame() to an inline function, hostapd_drv_send_mlme().
This is similar to the design that is used in wpa_supplicant and
that was used in hostapd in the past (hostapd_send_mgmt_frame()
inline function).
This makes it easier (and a bit faster) to handle multiple local
radios with FT. There is no need to depend on l2_packet in that
case since the frame can be delivered as a direct function call.
hostapd does not implement UAPSD functionality. However, if U-APSD
functionality is implemented outside hostapd, add support to advertise
the functionality in beacon.
Signed-off-by: yogeshp@marvell.com
This is needed to allow reassociation processing to skip 4-way handshake
when FT-over-DS is used with an AP that has a previous association state
with the STA.
Doxygen and some build tools may get a bit confused about same file
name being used in different directories. Clean this up a bit by
renaming some of the duplicated file names in src/ap.
