mac80211 authentication or association operation may get stuck for some
reasons, so wpa_supplicant better use an internal timer to recover from
this.
Signed-off-by: Ben Greear <greearb@candelatech.com>
When FT protocol run is completed with FT-EAP, the EAPOL state machine
needs to be notified of the completed authentication to make sure it
does not try to start new authentication.
This converts number of debugging messages to use wpa_msg() in order
to allow the interface name to be shown with the messages.
A new function, wpa_dbg(), is introduced to allow
CONFIG_NO_STDOUT_DEBUG=y builds to remove the debug strings. This is
otherwise identical with wpa_msg(), but it gets compiled out if stdout
debugging is disabled.
This is needed to allows WPS PBC session overlap detection to work
with drivers that process Probe Request frames internally. This
code is is run in hostapd, but the wpa_supplicant AP mode did not
have call to the hostapd_probe_req_rx() function even though it
registered handlers for hostapd Probe Request RX callbacks.
This was previously done for WPA/WPA2-Personal as part of association
processing when the driver is implementing 4-way handshake. The
portValid needs to be done for WPA/WPA2-Enterprise to get the proper
EAPOL authentication completed callback to configure PMK to the driver.
The driver may get confused if we set the initial TX GTK before having
fully configured and connected to an IBSS, so better delay this
operation until the connection (join/start IBSS) has been completed.
The proto configuration may be left to non-zero when moving from one
configuration to another. To avoid misidentifying a network
configuration as enabling WPA, check key_mgmt field, too.
This adds partial callbacks and events to allow P2P management to be
implemented in a driver/firmware. This is not yet complete and is
very much subject to change in the future.
The nl80211 driver can report low ACK condition (in fact it reports
complete loss right now only). Use that, along with a config option, to
disconnect stations when the data connection is not working properly,
e.g., due to the STA having went outside the range of the AP. This is
disabled by default and can be enabled with disassoc_low_ack=1 in
hostapd or wpa_supplicant configuration file.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The WPS mode was already verified when the AP was configured for
WPA/WPA2, but this was not done with AP that was in open mode.
Fix this by allowing wpa_supplicant_ssid_bss_match() to be called
in non-WPA configuration, too. With this change, wps_pbc BSSID
command will wait until the specified target AP is in active PBC
mode before trying to connect to it.
If a station received unprotected Deauthentication or Disassociation
frame with reason code 6 or 7 from the current AP, there may be a
mismatch in association state between the AP and STA. Verify whether
this is the case by using SA Query procedure. If not response is
received from the AP, deauthenticate.
This implementation is only for user space SME with
driver_nl80211.c.
Some new code I'm working on will need the scan_res_handler assigned all
the time in certain circumstances, so the easiest way is to reset it
within the handler. This is currently prevented by the way the code in
the event handler works -- change that to permit such usage.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When controlling multiple virtual interfaces on the same physical
radio, share the scan results events with sibling interfaces. This
decreases the time it takes to connect many virtual interfaces.
This is currently only supported on Linux with cfg80211-based
drivers when using nl80211 or wext driver interface.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Move the previously SME specific optimization code into generic
function that can be used from non-SME code, too, and use it to
handle disconnection events. In other words, allow disconnection
event to trigger similar optimized scanning case to handle a
common load balancing mechanism. If there is another BSS in the
same ESS when we receive a disconnection event, scan only the
known frequencies of such other BSSes on the next attempt to
speed up recovery.
The special case of requiring blacklisting count to be 2 or higher
is only needed when more than a single network is currently enabled.
As such, we should not do that when only a single network is enabled.
This make the station more likely to follow network side load
balancing attempts where the current AP may disassociate us with
an assumption that we would move to another AP.
assoc_freq needs to be cleared when an interface gets disconnected.
This fixes an issue where P2P Action frame transmission may fail
because of missing remain-on-channel operation when using the same
interface for group operations (or non-P2P connections) and P2P
management operations.
The wpa_supplicant_event() EVENT_TX_STATUS ack field needs to be
converted to use wpas_send_action_tx_status()
enum p2p_send_action_result in this case, too, to avoid getting
incorrect TX status for P2P processing.
By default, make hostapd and wpa_supplicant maintain an internal
entropy pool that is fed with following information:
hostapd:
- Probe Request frames (timing, RSSI)
- Association events (timing)
- SNonce from Supplicants
wpa_supplicant:
- Scan results (timing, signal/noise)
- Association events (timing)
The internal pool is used to augment the random numbers generated
with the OS mechanism (os_get_random()). While the internal
implementation is not expected to be very strong due to limited
amount of generic (non-platform specific) information to feed the
pool, this may strengthen key derivation on some devices that are
not configured to provide strong random numbers through
os_get_random() (e.g., /dev/urandom on Linux/BSD).
This new mechanism is not supposed to replace proper OS provided
random number generation mechanism. The OS mechanism needs to be
initialized properly (e.g., hw random number generator,
maintaining entropy pool over reboots, etc.) for any of the
security assumptions to hold.
If the os_get_random() is known to provide strong ramdom data (e.g., on
Linux/BSD, the board in question is known to have reliable source of
random data from /dev/urandom), the internal hostapd random pool can be
disabled. This will save some in binary size and CPU use. However, this
should only be considered for builds that are known to be used on
devices that meet the requirements described above. The internal pool
is disabled by adding CONFIG_NO_RANDOM_POOL=y to the .config file.
The driver wrapper may now indicate the preferred channel (e.g., based
on scan results) on both 2.4 GHz and 5 GHz bands (and an overall best
frequency). When setting up a GO, this preference information is used
to select the operating channel if configuration does not include
hardcoded channel. Similarly, this information can be used during
GO Negotiation to indicate preference for a specific channel based
on current channel conditions.
p2p_group_add command can now use special values (freq=2 and freq=5)
to indicate that the GO is to be started on the specified band.
Commit d8d940b746 introduced a regression
that prevented TSN APs from being used with WEP since the AP was
rejected if it advertised WPA or RSN IE when we were configured to use
WEP. Resolve this by checking whether the AP is advertising a TSN, i.e.,
whether the AP allows WEP to be used as a group cipher. If so, allow
the AP to be selected if we are configured to use static WEP or
IEEE 802.1X (non-WPA).
It should be noted that this is still somewhat more restricted in AP
selection than earlier wpa_supplicant branches (0.7.x or older) that
ignore the WPA/RSN IE completely when configured for non-WPA.
Add a new driver event, EVENT_INTERFACE_UNAVAILABLE, for indicating
that the driver is not able to continue operating the virtual
interface in its current mode anymore, e.g., due to operating
channel for GO interface forced to a DFS channel by another virtual
interface.
When this happens for a P2P group interface, the P2P group will
be terminated and P2P-GROUP-REMOVED event shows the reason for
this as follows:
P2P-GROUP-REMOVED wlan0 GO reason=UNAVAILABLE
The driver wrapper may indicate EVENT_CHANNEL_LIST_CHANGED before
completing init(). This would likely result in segfault when driver
channel list is being read as part of processing this event when
P2P is enabled.
The workaround to ignore no ctrl::ack received for GO Negotiation
Confirmation frame was only supposed to be used when the frame was
actually transmitted and just the ack was not received. However, due
to the way the driver failure on transmitting the frame were reported,
this ended up getting applied for all failures in sending the GO
Negotiation Confirmation frame.
Improve this by providing a mechanism to indicate whether send_action
operations fail locally before the frame was actually transmitted or
because of not receiving ack frame after having transmitted the frame.
Previously, wpa_supplicant remaining in scanning state without
trying to connect, but there is no particular need to do that.
Instead, cancel WPS operation completely whenever PBC session
overlap is detected.
Disconnection event may be received while in associating state.
Previously, wpa_supplicant could get stuck not trying to reconnect
in that case at least with nl80211. Allow scan request in this
state to avoid the issue. This helps especially with APs that do
load balancing by sending Deauthentication frame as a response to
Reassociation Request frame after successful Authentication frame
exchange.
ctrl_interface STA_AUTOCONNECT command can now be used to disable
automatic reconnection on receiving disconnection event. The default
behavior is for wpa_supplicant to try to reconnect automatically, i.e.,
to maintain previous behavior.
The overlap condition cannot disappear before group formation timeout
hits, so there is no point in continuing in this case and failure can
be indicated immediately.
If CONFIG_WPS_STRICT is set, validate WPS IE(s) in management frames and
reject the frames if any of the mandatory attributes is missing or if an
included attribute uses an invalid value. In addition, verify that all
mandatory attributes are included and have valid values in the WSC
messages.
Verify that the driver wrapper is using a valid deauth/disassoc
event before dereferencing the addr pointer. The address is required
to be set in AP mode, but it is safer to verify this here than to
trust on all driver wrappers doing the correct thing.
Commit d8d940b746 broke the logic on
iterating through all configured network blocks. This was supposed
to continue the loop on mismatch to allow other than the first
configured network to be found.
This removes quite a bit of duplicated code and allows network block
priority configuration to be used to prefer unprotected networks and
also allows use on open network with good signal strength even if
scan results show a protected network with marginal signal strength
that does not allow it to be used.
