This used to result in a segmentation fault due to use of freed memory
(mismatch in pointer lifetime between hostapd.c and driver_nl80211.c).
Signed-off-by: Jouni Malinen <j@w1.fi>
This is a regression test for an issue where scanning sequence could be
terminated if interworking_find_network_match() finds a matching
network, but wpa_s->auto_select is not set. This could stop connection
attempts when auto_interworking=1 is used and the scan results have a
partially matching network and no cred match.
Signed-off-by: Jouni Malinen <j@w1.fi>
radius_{auth,acct}_unreachable tested some parts of RADIUS client code
error handling. However, they did not test everything since the send()
calls for unreachable port on localhost did not return an error (that
error was reported on receive side). Extend this with similar test cases
using unreachable IP address to get send() error returns covered as
well.
Signed-off-by: Jouni Malinen <j@w1.fi>
ap_cipher_tkip_countermeasures_{ap,sta} printed out the MAC addresses in
stdout which resulted in the debug log not starting the PASS/FAIL
information at the beginning of the line. Hide these unnecessary prints
to avoid that.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The example IMV and IMC used for TNC testing has references to
wpa_printf and other functions from hostapd/wpa_supplicant. Link the
binaries in a way that allows these symbols to be resolved while loading
the libraries at run time.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Incorrect password was already tested with TTLS/MSCHAPv2, but the other
non-EAP inner methods in TTLS use their own implementation of password
validation, so check each and also verify the case of no matching EAP
user entry for the specific method.
Signed-off-by: Jouni Malinen <j@w1.fi>
This documents some more steps needed during initial test setup
configuration to make it easier to get this running even without
thorough knowledge of the network setup used by the operating system.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Scan explicitly for the specific AP to work around issues where under
heavy CPU load, the single active scan round may miss the delayed Probe
Response from the AP. In addition, verify that ANQP_GET commands succeed
to make error cases clearer in the log.
Signed-off-by: Jouni Malinen <j@w1.fi>
This verifies that the wait for peer to be ready for GO Negotiation is
timed out properly at no less than 120 seconds. Since this is a long
test case, it is disabled by default without the --long option.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Allow three P2P_FIND attempts for discovering the GO on a non-social
channels since the single Probe Response frame can be missed easily
under heavy CPU load.
Signed-off-by: Jouni Malinen <j@w1.fi>
Scan explicitly for the AP that may be started during the test case
execution. This is needed to work around issues where under heavy CPU
load, the single active scan round may miss the delayed Probe Response
from the second AP.
Signed-off-by: Jouni Malinen <j@w1.fi>
Instead of checking for multiple EAP starts (which can occur if
EAPOL-Start from supplicant goes out quickly enough, e.g., due to CPU
load), look for the explicit message indicating that TTLS method
initialization failed.
Signed-off-by: Jouni Malinen <j@w1.fi>
Scan explicitly for the AP that may be started during the test case
execution. This is needed to work around issues where under heavy CPU
load, the single active scan round may miss the delayed Probe Response
from the second AP. In addition, check for ROAM/FT_DS failures to be
able to report errors more clearly.
Signed-off-by: Jouni Malinen <j@w1.fi>
Scan explicitly for the AP that may be started during the test case
execution. This is needed to work around issues where under heavy CPU
load, the single active scan round may miss the delayed Probe Response
from the second AP.
Signed-off-by: Jouni Malinen <j@w1.fi>
These can fail during heavy CPU load due to active scan dwell time not
being long enough to catch the delayed Probe Response frame from the AP.
Work around this by allowing multiple scan attempts to see the response.
Signed-off-by: Jouni Malinen <j@w1.fi>
There was a bug in this code path that resulted in the
skip-scan-to-start-GO case to not actually skip the scan. It looks like
this could be hit at least when autoscan was enabled, but it is possible
that some other sequences could hit this as well.
Signed-off-by: Jouni Malinen <j@w1.fi>
Since P2P Client scan case is now optimzied to use a specific SSID, the
WPS AP will not reply to that and the scan after GO Negotiation can
quite likely miss the AP due to dwell time being short enoguh to miss
the Beaco frame. This has made the test case somewhat pointless, but
keep it here for now with an additional scan to confirm that PBC
detection works if there is a BSS entry for a overlapping AP.
Signed-off-by: Jouni Malinen <j@w1.fi>
The single channel scan while associated to another AP and immediately
after starting the second AP can miss the Probe Response frame
especially under heavy CPU load. Avoid false error reports by allowing
multiple scan rounds to be performed. wpas_ctrl_bssid_filter is also
modified to take into account different get_bss() behavior.
Signed-off-by: Jouni Malinen <j@w1.fi>
