The config says that the default for ap_table_max_size is 255 and the
default for ap_table_expiration_time is 60. But the code doesn't reflect
the default values mentioned in the sample config file.
These variables completely disable the code for Overlapping Legacy BSS
Condition by default when they are not correctly initialized. WFA
certification requires this feature and therefore an AP would have
failed the certification process unless they were initialized manually
using the configuration file.
Signed-hostap: Sven Eckelmann <sven@open-mesh.com>
Signed-hostap: Simon Wunderlich <simon@open-mesh.com>
WSC IE in Beacon and Probe Response frames should behave consistently
as far as the RF Bands attribute is concerned. Use the same dualband
condition for adding this into Probe Response frames since the value
is not really needed if the AP is not a dualband AP.
Signed-hostap: Jouni Malinen <j@w1.fi>
If separate hostapd processes are used for different RF bands, the
dualband parameter for WPS was not set correctly. Allow dualband
indication (mainly, addition of RF bands attribute for PBC session
overlap detection) also based on wps_rf_bands value (if set to "ag").
Signed-hostap: Jouni Malinen <j@w1.fi>
This allows Probe Request frame processing to compare the configured
SSID to the SSID List element in addition to the SSID element.
Signed-hostap: Jouni Malinen <j@w1.fi>
Replace CONFIG_IEEE80211V with CONFIG_WNM to get more consistent build
options for WNM-Sleep Mode operations. Previously it was possible to
define CONFIG_IEEE80211V without CONFIG_WNM which would break the build.
In addition, IEEE 802.11v has been merged into IEEE Std 802.11-2012 and
WNM is a better term to use for this new functionality anyway.
Signed-hostap: Jouni Malinen <j@w1.fi>
These fields do not use AES keywrap. Instead, they are protected with
management frame protection (and not included if PMF is disabled).
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Expiry can always trigger a deauthentication, but otherwise,
deauthentication should only happen when the *current* cache entry is
removed and not being replaced. It should not happen when the current
PMK just happens to match the PMK of the entry being removed, since
multiple entries can have the same PMK when OKC is used and these
entries are often removed at different times.
This fixes an issue where eviction of the oldest inactive entry due to
adding a newer entry to a full cache caused a deauthentication when the
entry being removed had the same PMK as the current entry.
Signed-hostap: Dan Williams <dcbw@redhat.com>
pmksa_cache_free_entry() takes care of updated the list head pointer
(pmksa->pmksa), so no need to do this change in the caller.
Signed-hostap: Jouni Malinen <j@w1.fi>
Use the shared_secret pointer from RADIUS client implementation instead
of getting this from hostapd configuration data.
Signed-hostap: Jouni Malinen <j@w1.fi>
This adds support for multiple PSKs per station when using a RADIUS
authentication server to fetch the PSKs during MAC address
authentication step. This can be useful if multiple users share a
device but each user has his or her own private passphrase.
Signed-hostap: Michael Braun <michael-dev@fami-braun.de>
Add pmf=1/2 to wpa_supplicant STATUS command output to indicate that PMF
was negotiated for the connect (1 = optional in this BSS, 2 = required
in this BSS).
Signed-hostap: Jouni Malinen <j@w1.fi>
Previously, PMF (protected management frames, IEEE 802.11w) could be
enabled only with a per-network parameter (ieee80211w). The new global
parameter (pmf) can now be used to change the default behavior to be PMF
enabled (pmf=1) or required (pmf=2) for network blocks that do not
override this with the ieee80211w parameter.
Signed-hostap: Jouni Malinen <j@w1.fi>
We enable this feature for non-SME drivers as well if
they explicitly indicate need for it.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Add the configuration option vht_oper_centr_freq_seg1_idx
for the second segment of an 80+80 MHz channel and use it
when building the VHT operation IE.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
If netlink_init() fails on socket create or bind the cfg struct
provided as parameter is freed by netlink_init(). Callers of
netlink_init() also free this struct on their error paths leading
to double free.
Signed-hostap: Pontus Fuchs <pontus.fuchs@gmail.com>
This allows the AP to figure out whether a station is a HS 2.0 STA
during the association and access any information that the STA may have
included in this element.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Change the maximum retry limit from 10 to 120 to match the behavior
used with GO Negotiation Request frames when trying to start GO
Negotiation with a peer that does not acknowledge frames (e.g., due
to being in sleep or on another channel most of the time).
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The GO may be in sleep when we send a PD Request frame to indicate that
we are about to join a running group. Previously, this frame was not
retried more than normal low level retries. This can result in the GO
not getting the frame especially in cases where concurrent multi-channel
operations or aggressive sleep schedule is used since most drivers do
not yet synchronize with the GO's NoA before association.
Increase the likelihood of the GO receiving the PD Request frame by
retransmitting it similarly to the PD-for-GO-Negotiation case. Start
the actual join operation only after these retries have failed to get
an acknowledgment from the GO to give the connection attempt a chance
to succeed if the driver implements better NoA synchronization for it.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
p2p_prov_disc_req() used the join parameter to figure out whether the PD
request was a user initiated or not. This does not cover all use cases
of PD, so add a separate parameter to allow caller to indicate whether
the user requested the operation.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
CONFIG_SQLITE=y option can now be used to allow the eap_user_file text
file to be replaced with a SQLite database
(eap_user_file=sqlite:/path/to/sqlite.db). hostapd.eap_user_sqlite
shows an example of how the database tables can be created for this
purpose. This commit does not yet include full functionality of the
text file format, but at least basic EAP-TTLS/MSCHAPv2 style
authentication mechanisms with plaintext passwords can be used for
tests.
Signed-hostap: Jouni Malinen <j@w1.fi>
The NL80211_CMD_TDLS_OPER command can be used as an event based on a
recent cfg80211 commit, so add code to map that to internal
wpa_supplicant event to request TDLS link setup/teardown.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Commit 296a34f0c1 changed hostapd to
remove the internal STA entry at the beginning of TKIP countermeasures.
However, this did not take into account the case where this is triggered
by an EAPOL-Key error report from a station. In such a case, WPA
authenticator state machine may continue processing after having
processed the error report. This could result in use of freed memory.
Fix this by stopping WPA processing if the STA entry got removed.
Signed-hostap: Jouni Malinen <j@w1.fi>
Some deployed station implementations implement WPS incorrectly and
end up causing PBC session overlap issues by indicating active PBC
mode in a scan after the WPS provisioning step. Work around this by
ignoring active PBC indication in a Probe Request from a station that
completed PBC provisioning during the last five seconds.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Commits 07783eaaa0 and
3da372fae8 removed the only users of the
disassociate() driver operation, so these driver wrapper functions can
also be removed now.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Change the nl80211 driver in wpa_supplicant to correctly handle
connecting to a new AP through cfg80211 without SME capability. As
before, the driver will disconnect from the previously associated AP,
but now we attempt to immediately connect to our intended AP. This
prevents us from blacklisting the AP we were trying to connect to
because of a semantic mismatch between cfg80211 and wpa_supplicant. The
disconnect/connect patch generates a local disconnect nl80211 event
which we discard because we're already correctly tracking the pending
association request.
In detail:
cfg80211 does not support connecting to a new BSS while already
connected to another BSS, if the underlying driver doesn't support
separate authenticate and associate commands. wpa_supplicant is written
to expect that this is a supported operation, except for a little error
handling that disconnects from the current BSS when roaming fails and
relies on autoconnect logic to reconnect later. However, this failure to
connect is incorrectly attributed to the new AP we attempted to
associate with, rather than a local condition in cfg80211.
The combined effect of these two conditions is that full-mac drivers
accessible through cfg80211 but without SME capability take a long time
to roam across BSS's because wpa_supplicant will:
1) Fail to associate for local reasons
2) Disconnect and return that the association request failed
3) Blacklist the association target (incorrectly)
4) Do a scan
5) Pick a less desirable AP to associate with
Signed-hostap: Christoper Wiley <wiley@chromium.org>
Commit deca6eff74 added a redundant call
to l2_packet_get_own_addr. Use the information we already have in
atheros_init.
Signed-hostap: Baruch Siach <baruch@tkos.co.il>
If identity round limit is reached, EAP-SIM/AKA session is terminated.
This needs to free the allocated message.
Signed-hostap: Jouni Malinen <j@w1.fi>
There is no point in the hapd_iface == NULL validate after this pointer
has been dereferences, so move the code dereferencing hapd_iface after
the check.
Signed-hostap: Jouni Malinen <j@w1.fi>
The UFD (USB flash drive) configuration method was deprecated in WSC
2.0. Since this is not known to be used, remove the UFD implementation
from hostapd and wpa_supplicant to allow the WPS implementation to be
cleaned up. This removes the now unused OOB operations and ctrl_iface
commands that had already been deprecated by the new NFC operations.
Signed-hostap: Jouni Malinen <j@w1.fi>
The PSK generation done by pbkdf2_sha1() is one of the longest CPU time
users according to our profiling from boot to GO started.
So I have reduced some steps.
I could boot a GO by this command sequence.
-------------
add_net
set_network 0 ssid '"DIRECT-XX"'
set_network 0 psk
'"123456789012345678901234567890123456789012345678901234567890123"'
set_network 0 proto RSN
set_network 0 key_mgmt WPA-PSK
set_network 0 pairwise CCMP
set_network 0 auth_alg OPEN
set_network 0 mode 3
set_network 0 disabled 2
p2p_group_add persistent=0 freq=2412
-------------
By this sequence, pbkdf2_sha1() was called three times and the function
calculates the same value each time. Reduce number of calls to
pbkdf2_sha1() from 3 to 1 by caching the previous result.
Signed-hostap: Masashi Honma <masashi.honma at gmail.com>
This function is now unused after the last couple of commits that
removed the last uses, so remove this to keep code simpler since all
places that disassociate, can use deauthentication instead.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Even though the standard currently describes disassociation to be used
for RSN element mismatch between Beacon/Probe Response frames and
EAPOL-Key msg 3/4, this is unnecessary difference from other cases that
deauthenticate. In addition, there is no point in leaving the 802.11
Authentication in place in this case. To keep things simpler, use
deauthentication here to get rid of the only use of
wpa_sm_disassociate().
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
If WPS Registrar tries to provision a WPA/WPA2-Personal network without
including a valid Network Key, the network block cannot be used to
connect to the network. Reject such credential without adding the
network block. This makes wpa_supplicant send WSC_NACK as a response to
the invalid Credential and stop the provisioning process immediately
rather than only after trying unsuccessfully to connect to the network.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The new P2P_SET parameter disc_int can now be used to configure
discoverable interval for p2p_find operations. The format of the command
for setting the values is "P2P_SET disc_int <minDiscoverableInterval>
<maxDiscoverableInterval> <max TUs for discoverable interval>". The
first two parameters are given in units of 100 TUs (102.4 ms). The third
parameter can be used to further limit the interval into a specific TU
amount. If it is set to -1, no such additional limitation is enforced.
It should be noted that the P2P specification describes the random
Listen state interval to be in units of 100 TUs, so setting the max TU
value to anything else than -1 is not compliant with the specification
and should not be used in normal cases. The default parameters can be
set with "P2P_SET disc_int 1 3 -1".
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The old WPS interface for using NFC has no known deployments and even
the binary libraries referenced here are not easily available anymore.
Since the new interface for using NFC with WPS covers the same
functionality, remove the old implementation to clean up WPS
implementation.
Signed-hostap: Jouni Malinen <j@w1.fi>
When WPS is used with NFC connection handover, the AP may indicate its
operating channel within the credential information. Use this
informatiom, if present, to speed up the scan process.
Signed-hostap: Jouni Malinen <j@w1.fi>
This commit adds new wpa_supplicant ctrl_iface commands to allow
external programs to go through NFC connection handover mechanism
with wpa_supplicant taking care of the WPS processing. This version
includes only the case where wpa_supplicant is operating as a
station/Enrollee.
Signed-hostap: Jouni Malinen <j@w1.fi>
The previous eapol_sm_notify_cached() implementation forced the port
to be authorized when receiving EAPOL-Key msg 1/4 that included a
matching PMKID in cases when PMKSA caching is used. This is too early
since the port should really be authorized only after the PTK has been
configured which is the case when PMKSA caching is not used.
Fix this by using the EAPOL supplicant PAE state machine to go through
the AUTHENTICATING and AUTHENTICATED states instead of forcing a jump
to AUTHENTICATED without performing full state machine steps. This can
be achieved simply by marking eapSuccess TRUE at least with the current
version of EAP and EAPOL state machines (the earlier commits in this
function seemed to indicate that this may have not been that easy in
the older versions due to the hacks needed here).
This addresses an issue with nl80211-based driver interface when the
driver depends on the STA Authorized flag being used to prevent
unprotected frames from being accepted (both TX and RX) prior to PTK
configuration.
Signed-hostap: Jouni Malinen <j@w1.fi>
intended-for: hostap-1
If the driver indicates support for multi-channel concurrency, change
the p2p_connect behavior to not force the current operating channel, but
instead, just mark it as preferred for GO Negotiation. This change
applies only for the case when the freq parameter is not used with the
p2p_connect command.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
There was an issue with EAPOL frame exchanges in a multi-BSS
configuration when a station switches between the BSSes controlled by
the same hostapd process. When processing the EAPOL packet, the array of
virtual APs (iface->bss) is searched looking for the station that sent
the packet in order to identify which signal context should be used
during processing. The first match of the station in its list gets used
in the ieee802_1x_receive() function. However, even after a station has
disassociated, it remains in the list of stations pending an inactivity
timeout. This leads to the wrong hapd context (one where the station had
already disassociated) being used in some cases (if the current/active
bss entry appears in the list after one where the station has just
disassociated from) for EAPOL processing.
Fix this by checking the WLAN_STA_ASSOC flag before assuming the right
hapd context was found for the given station.
Signed-hostap: David Bird <dbird@powercloudsystems.com>
intended-for: hostap-1
This uses the recent cfg80211 changes to allow SAE authentication to be
implemented with the nl80211 driver interface.
Signed-hostap: Jouni Malinen <j@w1.fi>
P2P includes two use cases where one of the devices is going to start a
group and likely change channels immediately after processing a frame.
This operation may be fast enough to make the device leave the current
channel before the peer has completed layer 2 retransmission of the
frame in case the ctrl::ack frame was lost. This can result in the peer
not getting TX status success notification.
For GO Negotiation Confirm frame, p2p_go_neg_conf_cb() has a workaround
that ignores the TX status failure and will continue with the group
formation with the assumption that the peer actually received the frame
even though we did not receive ctrl::ack. For Invitation Response frame
to re-invoke a persistent group, no such workaround is used in
p2p_invitation_resp_cb(). Consequently, TX status failure due to lost
ctrl::ack frame results in one of the peers not starting the group.
Increase the likelihood of layer 2 retransmission getting acknowledged
and ctrl::ack being received by waiting a short duration after having
processed the GO Negotiation Confirm and Invitation Response frames for
the re-invocation case. For the former, use 20 ms wait since this case
has been worked around in deployed devices. For the latter, use 50 ms
wait to get even higher likelihood of getting ctrl::ack through since
deployed devices (and the current wpa_supplicant implementation) do not
have a workaround to ignore TX status failure.
20 ms is long enough to include at least couple of retries and that
should increase likelihood of getting ctrl::ack through quite a bit. The
longer 50 ms wait is likely to include full set of layer 2 retries.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Commit 458cb30191 broke LEAP since it
rejects EAP-Success packet that is used within LEAP and this frame does
not have a payload. Fix LEAP by relaxing the generic EAP packet
validation if LEAP has been negotiated.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Previously, WPS Registrar allowed multiple wildcard PINs to be
configured. This can get confusing since these PINs get assigned to any
Enrollee that does not have a specific PIN and as such, cannot really be
used with different PIN values in reasonable ways. To avoid confusion
with multiple enabled PINs, invalidate any previously configured
wildcard PIN whenever adding a new one.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
While the existing code already addresses TLS Message Length validation
for both EAP-TLS peer and server side, this adds explicit checks and
rejection of invalid messages in the functions handling reassembly. This
does not change externally observable behavior in case of EAP server.
For EAP peer, this starts rejecting invalid messages instead of
addressing them by reallocating the buffer (i.e., ignoring TLS Message
Length in practice).
Signed-hostap: Jouni Malinen <j@w1.fi>
EAP-TLS/PEAP/TTLS/FAST server implementation did not validate TLS
Message Length value properly and could end up trying to store more
information into the message buffer than the allocated size if the first
fragment is longer than the indicated size. This could result in hostapd
process terminating in wpabuf length validation. Fix this by rejecting
messages that have invalid TLS Message Length value.
This would affect cases that use the internal EAP authentication server
in hostapd either directly with IEEE 802.1X or when using hostapd as a
RADIUS authentication server and when receiving an incorrectly
constructed EAP-TLS message. Cases where hostapd uses an external
authentication are not affected.
Thanks to Timo Warns for finding and reporting this issue.
Signed-hostap: Jouni Malinen <j@w1.fi>
intended-for: hostap-1
This replaces the previously used bogus test data in SAE messages with
the first real field. The actual SAE authentication mechanism is still
missing and the Scaler, Element, and Confirm fields are not included.
Signed-hostap: Jouni Malinen <j@w1.fi>
Channel frequency for 60 GHz band do not fit into 'short int', as was
used. Expand it to 'int'
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
These values are used with WAPI and CCX and reserving the definitions
here reduces the number of merge conflicts with repositories that
include these functions.
Signed-hostap: Jouni Malinen <j@w1.fi>
This introduces new AKM for SAE and FT-SAE and adds the initial parts
for going through the SAE Authentication frame exchange. The actual SAE
algorithm and new fields in Authentication frames are not yet included
in this commit and will be added separately. This version is able to
complete a dummy authentication with the correct authentication
algorithm and transaction values to allow cfg80211/mac80211 drivers to
be tested (all the missing parts can be handled with
hostapd/wpa_supplicant changes).
Signed-hostap: Jouni Malinen <j@w1.fi>
This allows hostapd_cli and wpa_cli all_sta command to be used to
display connected time (in seconds) of each station in AP mode.
Signed-hostap: Raja Mani <rmani@qca.qualcomm.com>
Commit 6b56cc2d97 added clearing of the
p2p->pending_action_state too early in this function. This should not
be done if we are going to silently ignore the frame due to dialog
token mismatch. Fix this by moving the code around to check the dialog
token first.
This issue resulted in PD Request retries getting stopped too early if
the peer is sending out an unexpected PD Response (e.g., because of it
being excessively slow with the response so that the response is
received only after the next TX attempt with a new dialog token).
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Make Invitation process for re-invoking a persistent group behave
similarly to GO Negotiation as far as channel negotiation is concerned.
The Operating Channel value (if present) is used as a starting point if
the local device does not have a forced operating channel (e.g., due to
concurrent use). Channel lists from devices are then compared to check
that the selected channel is in the intersection. If not, channel is
selected based on GO Negotiation channel rules (best channel preferences
etc.). Invitation Request is rejected if no common channel can be
selected.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
As long as WLAN_STA_ASSOC_REQ_OK is set in sta->flags, Class 3 frames do
not trigger a disassoc/deauth. If it is still set even after the assoc
response tx has already failed, it may take somewhat longer for clients
to realize that the connection wasn't fully established.
Signed-hostap: Felix Fietkau <nbd@openwrt.org>
This avoids extra latency caused by establishing an aggregation session
and makes the initial connection attempt more reliable
Signed-hostap: Felix Fietkau <nbd@openwrt.org>
This patch fixes an issue where removing a WDS VLAN interface also
removed the main AP interface from the same bridge.
Signed-hostap: Felix Fietkau <nbd@openwrt.org>
This is a generic AES CCM implementation that can be used for other
purposes than just implementing CCMP, so it fits better in a separate
file in src/crypto.
Signed-hostap: Jouni Malinen <j@w1.fi>
Now that the internal AES implementation supports 256-bit keys, enable
use of the TLS cipher suites that use AES-256 regardless of which crypto
implementation is used.
Signed-hostap: Jouni Malinen <j@w1.fi>
AES uses the same 128-bit block size with 128, 192, 256 bit keys, so use
the fixed block size definition instead of trying to dynamically set the
block size based on key length. This fixes use of 192-bit and 256-bit
AES keys with crypto_cipher_*() API when using the internal AES
implementation.
Signed-hostap: Jouni Malinen <j@w1.fi>
This is otherwise identical to aes_gcm_ae() but does not use the
plain/crypt pointers since no data is encrypted.
Signed-hostap: Jouni Malinen <j@w1.fi>
This adds 192-bit and 256-bit key support to the internal AES
implementation and extends the AES-GCM functions to accept key length to
enable longer AES key use.
Signed-hostap: Jouni Malinen <j@w1.fi>
This is a generic AES GCM and GMAC implementation that can be used for
other purposes than just implementing GCMP, so it fits better in a
separate file in src/crypto.
Signed-hostap: Jouni Malinen <j@w1.fi>
The conf doesn't contain any basic rates in some cases. Most notably,
when starting a P2P GO in 5 GHz. Use the iface rates which are
initialized in hostapd_prepare_rates() to the conf rates or set to
default values if no conf values exist. This fixes a bug introduced in
commit e5693c4775.
Signed-hostap: Arik Nemtsov <arik@wizery.com>
Commit e5693c4775 added a copy of the
determined basic rate set into struct hostapd_iface, but did not
actually copy the terminating -1 value. This could be problematic if
something were to actually try to use this list since would be no way to
know what is the last entry in the list. Fix this by copying the
terminating value.
Signed-hostap: Jouni Malinen <j@w1.fi>
This driver_op can now be used in station mode, too, to fetch
information about the connection with the AP, so allow this to be used
even if wpa_supplicant is built without AP mode support.
Signed-hostap: Jouni Malinen <j@w1.fi>
The group matching should be done by comparing the P2P Interface Address
(which the group_bssid here is) to the group's BSSID and not the group
ID (which uses P2P Device Address and would have also needed the SSID).
Though, it should be noted that this case cannot really happen since a
GO in an active group would never be invited to join another group in
its GO role (i.e., if it receives an Invitation Request, it will reply
in P2P Device role). As such, this fix does not really change any
observable behavior, but anyway, it is good to keep the implementation
here consistent with the Invitation Request case.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
When building the Invitation Request for WFD use cases, match the BSSID,
i.e., P2P Interface Address, of the group on the GO to avoid using
information from another group should the device be operating multiple
concurrent groups as GO.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Use the anonymous_identity field to store EAP-SIM/AKA pseudonym identity
so that this can be maintained between EAP sessions (e.g., after
wpa_supplicant restart) even if fast re-authentication data was cleared.
Signed-hostap: Jouni Malinen <j@w1.fi>
The EAP-SIM/AKA code is already validating the prefix and the following
lookup would not find matches if the prefix is incorrect, so there is no
need for the extra checks here.
Signed-hostap: Jouni Malinen <j@w1.fi>
If EAP-Response/Identity includes a known pseudonym or re-auth username,
skip the AKA/Identity exchange since we already know the permanent
username of the peer.
Signed-hostap: Jouni Malinen <j@w1.fi>
RFC 4186, chapter 6.3.3 mandates that EAP-Failure is used only after
Client-Error and Notification messages. Convert the direct jumps to the
FAILURE state with a notification round before sending out EAP-Failure.
Signed-hostap: Jouni Malinen <j@w1.fi>
The AT_NONCE_S value needs to be used in AT_MAC calculation for
SIM/Re-authentication response even if re-authentication is rejected
with AT_COUNTER_TOO_SMALL.
Signed-hostap: Jouni Malinen <j@w1.fi>
intended-for: hostap-1
If the peer rejects re-authentication with AT_COUNTER_TOO_SMALL, fall
back to full authentication to allow the authentication session to be
completed.
Signed-hostap: Jouni Malinen <j@w1.fi>
These fields are used only as the search key, so the value is already
known and does not need to be copied from the database.
Signed-hostap: Jouni Malinen <j@w1.fi>
Store permanent username (i.e., including prefix character) instead of
IMSI in the SQLite DB. Convert the string to a string since the EAP-AKA
prefix can start with zero. This cleans up the field names since the
value was already with the prefix included instead of just IMSI. In
addition, this explicitly removes some theoretical cases where the
different identity types could have been mixed.
Signed-hostap: Jouni Malinen <j@w1.fi>
Since the EAP-SIM/AKA identities are ASCII strings, there is no need to
use more complex way for storing and passing them. In addition, be more
strict about enforcing username (i.e., no realm part) to be used in the
EAP-SIM DB API. Similarly, require specific username type instead of any
of the types to be used as the key in the pseudonym and reauth
operations. This allows simpler lookup operations to be used.
Signed-hostap: Jouni Malinen <j@w1.fi>
Since we always request an identity in the request, the response
has to include AT_IDENTITY. This allows the AKA/Identity response
processing to be simplified a bit.
Signed-hostap: Jouni Malinen <j@w1.fi>
There is no need to use eap_sim_db_identity_known() here since a new
AKA/Identity message is built only if the identity in the previous
response was not recognized. The first round is always used to request
AT_ANY_ID_REQ to meet the RFC 4187 recommendation on EAP method specific
identity request.
Signed-hostap: Jouni Malinen <j@w1.fi>
Since we always request an identity in the request, the response
has to include AT_IDENTITY. This allows the SIM/Start response
processing to be simplified a bit.
Signed-hostap: Jouni Malinen <j@w1.fi>
There is no need to use eap_sim_db_identity_known() here since a new
SIM/Start message is built only if the identity in the previous response
was not recognized. The first round will always request AT_ANY_ID_REQ to
meet the RFC 4186 recommendation on EAP method specific identity request
being used.
Signed-hostap: Jouni Malinen <j@w1.fi>
The reauth_id prefix can be used to determine which AKA version is used,
so there is no need to store the aka_prime information in a separate
field.
Signed-hostap: Jouni Malinen <j@w1.fi>
If hostapd is built and configured to use SQLite database, store
EAP-SIM/AKA reauth data into the database to allow this to persist
over hostapd restarts.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This allows hostapd to use an SQLite database for storing EAP-SIM/AKA
pseudonyms over process restarts. CONFIG_SQLITE=y build option adds
support for this and the SQLite database file is specified in eap_sib_db
configuration parameter.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Try to share most of the cipher information like key and RSC lengths and
suite selector conversions, etc. in wpa_common.c to avoid having similar
code throughout the WPA implementation for handling cipher specific
behavior.
Signed-hostap: Jouni Malinen <j@w1.fi>
wpa_cli p2p_serv_disc_req command can now be used to request WSD
request to be sent to specified or all peers who support WSD.
format: wifi-display <list of roles> <list of subelements>
examples:
p2p_serv_disc_req 00:00:00:00:00:00 wifi-display [source] 2,3,4,5
p2p_serv_disc_req 02:01:02:03:04:05 wifi-display [pri-sink] 3
p2p_serv_disc_req 00:00:00:00:00:00 wifi-display [sec-source] 2
p2p_serv_disc_req 00:00:00:00:00:00 wifi-display [source+sink] 2,3,4,5
p2p_serv_disc_req 00:00:00:00:00:00 wifi-display [source][pri-sink] 2,3,4,5
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This commit adds control interface commands and internal storage of
Wi-Fi Display related configuration. In addition, WFD IE is now added
to various P2P frames, Probe Request/Response, and (Re)Association
Request/Response frames. WFD subelements from peers are stored in the
P2P peer table.
Following control interface commands are now available:
SET wifi_display <0/1>
GET wifi_display
WFD_SUBELEM_SET <subelem> [hexdump of length+body]
WFD_SUBELEM_GET <subelem>
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This allows both hostapd and wpa_supplicant to be used to derive and
configure keys for GCMP. This is quite similar to CCMP key
configuration, but a different cipher suite and somewhat different rules
are used in cipher selection. It should be noted that GCMP is not
included in default parameters at least for now, so explicit
pairwise/group configuration is needed to enable it. This may change in
the future to allow GCMP to be selected automatically in cases where
CCMP could have been used.
This commit does not included changes to WPS or P2P to allow GCMP to be
used.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Use the NL80211_IFACE_COMB_NUM_CHANNELS value > 1 as a trigger for
enabling support for P2P multichannel channel concurrency. This does not
handle all possible details of enforcing driver capabilities, but it is
a good first step for allowing nl80211 drivers to enable multichannel
concurrency.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The new gas_request and gas_response_get commands can be used to request
arbitary GAS queries to be performed. These can be used with ANQP or
with other (including vendor specific) advertisement protocols.
gas_request <BSSID> <AdvProtoID> [Query]
gas_response_get <addr> <dialog token> [offset,length]
For example, ANQP query for Capability list in interactive wpa_cli
session:
> gas_request 02:00:00:00:01:00 00 000102000101
<3>GAS-RESPONSE-INFO addr=02:00:00:00:01:00 dialog_token=0
status_code=0 resp_len=32
> gas_response_get 02:00:00:00:01:00 00
01011c00010102010501070108010c01dddd0c00506f9a110200020304050607
> gas_response_get 02:00:00:00:01:00 00 0,10
01011c00010102010501
> gas_response_get 02:00:00:00:01:00 00 10,10
070108010c01dddd0c00
> gas_response_get 02:00:00:00:01:00 00 20,10
506f9a11020002030405
> gas_response_get 02:00:00:00:01:00 00 30,2
0607
It should be noted that the maximum length of the response buffer is
currently 4096 bytes which allows about 2000 bytes of the response data
to be fetched with a single gas_response_get command. If the response is
longer, it can be fetched in pieces as shown in the example above.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The new vendor_elements parameter in hostapd.conf can be used to add new
vendor specific element(s) into Beacon and Probe Response frames.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Maintain state of WPS APs during iteration to find the correct AP for
WPS PIN operation when no specific BSSID is specified. This information
can be used for optimizing the order in which the APs are tried. This
commit is only adding the collection of the information and more
detailed debug information to make debug logs more helpful in figuring
out how the AP selection order could be improved.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
If 4-way handshake fails due to likely PSK failure or if EAP
authentication fails, disable the network block temporarily. Use longer
duration if multiple consecutive failures are seen.
Signed-hostap: Jouni Malinen <j@w1.fi>
Replace the Venue Name specific data structure and parser with a
generic mechanism that can be used with other fields that use the
same format.
Signed-hostap: Jouni Malinen <j@w1.fi>
The anqp_3gpp_cell_net parameter can be used to configure hostapd
to advertise 3GPP Cellular Network ANQP information.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
These function pointers are going to be the same for each interface so
there is no need to keep them in struct hostapd_iface. Moving them to
struct hapd_interfaces makes it easier to add interfaces at run time.
Signed-hostap: Jouni Malinen <j@w1.fi>
The driver_test.c data structures had been changed to use a separate
BSS structure, but the P2P commands were not using the new design.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Commit 488f4a7108 configures a timer
before p2p_send_action(). This may result in the timer getting fired
earlier to the off channel transmission of the frame and thus another PD
request being retransmitted. This shall lead to the new PD request with
an incremented dialog token being transmitted. For the cases where the
later PD request might not be transmitted as the host driver is busy
transmitting the earlier frame, the received PD response could be
dropped for the dialog token mismatch. Remove the timer configuration to
avoid this behavior.
Signed-hostap: Sunil Dutt Undekari <duttus@codeaurora.org>
intended-for: hostap-1
Previously, all station mode scan operations were either skipped or
delayed while any P2P operation was in progress. To make concurrent
operations easier to use, reduce this limitation by allowing a scan
operation to be completed in the middle of a p2p_find. In addition,
allow station mode association to be completed. When the station mode
operation is run to its completion (scan results not acted on,
connection to an AP completed, connection failed), resume the p2p_find
operation.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
A new optional delay=<search delay in milliseconds> parameter can now be
used with p2p_find command to request an extra delay between search
iterations. This can be used, e.g., to make p2p_find friendlier to
concurrent operations by avoiding it from taking 100% of the radio
resources.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This EAP type uses a vendor specific expanded EAP header to encapsulate
EAP-TLS with a configuration where the EAP server does not authenticate
the EAP peer. In other words, this method includes only server
authentication. The peer is configured with only the ca_cert parameter
(similarly to other TLS-based EAP methods). This method can be used for
cases where the network provides free access to anyone, but use of RSN
with a securely derived unique PMK for each station is desired.
The expanded EAP header uses the hostapd/wpa_supplicant vendor
code 39068 and vendor type 1 to identify the UNAUTH-TLS method.
Signed-hostap: Jouni Malinen <j@w1.fi>
The previous implementation was able to re-open the connection to an
external program (e.g., hlr_auc_gw) when needed, but required the
connection to be available during startup. Extend this to allow the
initial failure, so that hlr_auc_gw can be started after hostapd.
Signed-hostap: Jouni Malinen <j@w1.fi>
Explicitly validate seed_len to skip memset call with zero length of
copied data at the end of the buffer. This is not really needed, but it
makes the code a bit easier for static analyzers. This is identical to
the commit a9ea17491a but for the OpenSSL
version of the function.
Signed-hostap: Jouni Malinen <j@w1.fi>
Commit bfc62fe133 moved the code that
using crypto/random.h, but forgot to remove the inclusion of that header
file.
Signed-hostap: Jouni Malinen <j@w1.fi>
All the TNC base64 operations are within tncs.c, so there is no point in
including base64.h into eap_server_tnc.c.
Signed-hostap: Jouni Malinen <j@w1.fi>
All the other places processing EVENT_RX_MGMT events assume that the
event data is included, so not much point in verifying that here.
Signed-hostap: Jouni Malinen <j@w1.fi>
Use an explicit pointer to the beginning of the buffer and a flag
to indicate whether that is to external data or not. This avoids
a branch whenever accessing the buffer and helps some static
analyzers to understand the wpabuf memory uses better.
Signed-hostap: Jouni Malinen <j@w1.fi>
If the os_malloc() call for the User-Name value fails in EAP-TTLS
server, the inner MSCHAPv2 processing could have tried to dereference a
NULL pointer. Avoid this by handling this cleanly as an internal error
and reject the authentication attempt.
Signed-hostap: Jouni Malinen <j@w1.fi>
intended-for: hostap-1
Commit c9e08af24f removed the only user of
the special case MD5 use that would be allowed in FIPS mode in
tls_prf_sha1_md5(). Commit 271dbf1594
removed the file from the build, but left the implementation into the
repository. To clean things up even further, remove this functionality
completely since it is not expected to be needed for FIPS mode anymore.
Signed-hostap: Jouni Malinen <j@w1.fi>
This allows User-Name and Chargeable-User-Identity attributes to be
passed from Access-Accept into Accounting messages even when IEEE 802.1X
is not used.
Signed-hostap: Michael Braun <michael-dev@fami-braun.de>
The mechanism to figure out key block size based on ssl->read_hash
does not seem to work with OpenSSL 1.0.1, so add an alternative
mechanism to figure out the NAC key size that seems to work at
least with the current OpenSSL 1.0.1 releases.
Signed-hostap: Jouni Malinen <j@w1.fi>
intended-for: hostap-1
Some deployed authentication servers seem to be unable to handle the TLS
Session Ticket extension (they are supposed to ignore unrecognized TLS
extensions, but end up rejecting the ClientHello instead). As a
workaround, disable use of TLS Sesson Ticket extension for EAP-TLS,
EAP-PEAP, and EAP-TTLS (EAP-FAST uses session ticket, so any server that
supports EAP-FAST does not need this workaround).
Signed-hostap: Jouni Malinen <j@w1.fi>
tls_disable_session_ticket=1 in phase1/phase2 can now be used to disable
use of TLS Session Ticket extension (which is enabled by default in
recent OpenSSL versions). This can be used to work around issues with
broken authentication servers that do not ignore unrecognized TLS
extensions properly.
Signed-hostap: Jouni Malinen <j@w1.fi>
This can be used to implement workaround for authentication servers that
do not handle TLS extensions in ClientHello properly.
Signed-hostap: Jouni Malinen <j@w1.fi>
The PKCS5_PBKDF2_HMAC_SHA1() function in OpenSSL 0.9.7 did not mark
the salt parameter const even though it was not modified. Hide the
compiler warning with a type cast when an old OpenSSL version is
used.
Signed-hostap: Jouni Malinen <j@w1.fi>
When CONFIG_FIPS=y is used, do not include MD5 in the build and disable
EAPOL-Key frames that use MD5 (WPA/TKIP and dynamic WEP with IEEE
802.1X).
Signed-hostap: Jouni Malinen <j@w1.fi>
Only allow the TLS library keying material exporter functionality to be
used for MSK derivation with TLS-based EAP methods to avoid exporting
internal TLS keys from the library.
Signed-hostap: Jouni Malinen <j@w1.fi>
Use SSL_export_keying_material() if possible, i.e., if OpenSSL is
version 1.0.1 or newer and if client random value is used first. This
allows MSK derivation with TLS-based EAP methods (apart from EAP-FAST)
without exporting the master key from OpenSSL.
Signed-hostap: Jouni Malinen <j@w1.fi>
Previously, CONFIG_EAP_MSCHAPV2=y was assumed to be set for
CONFIG_EAP_TTLS=y. Avoid this dependency by making including the
MSCHAPv2 parts in EAP-TTLS conditionally.
Signed-hostap: Jouni Malinen <j@w1.fi>
In theory, the SHA1 operation may fail (e.g., if SHA1 becomes disallowed
in some security policies), so better check the return code from
challenge_hash().
Signed-hostap: Jouni Malinen <j@w1.fi>
Do not leave the tls_global context allocated if the global OpenSSL
initialization fails. This was possible in case of FIPS builds if
the FIPS mode cannot be initialized.
Signed-hostap: Jouni Malinen <j@w1.fi>
Increase GO config timeout if HT40 is used since it takes some time
to scan channels for coex purposes before the BSS can be started.
Signed-hostap: Jouni Malinen <j@w1.fi>
Add optional "ht40" argument for p2p_group_add command to enable 40 MHz
in 5GHz band. This configures the secondary channel, when HT support is
enabled and if the HW supports 40 MHz channel width.
Signed-hostap: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
This function can be used as a wrapper for os_realloc(ptr, nmemb * size)
when a reallocation is used for an array. The main benefit over
os_realloc() is in having an extra check to catch integer overflows in
multiplication. This is similar to the os_zalloc() to os_calloc() move.
Signed-hostap: Jouni Malinen <j@w1.fi>
This function can be used as a wrapper for os_zalloc(nmemb * size) when
an allocation is used for an array. The main benefit over os_zalloc() is
in having an extra check to catch integer overflows in multiplication.
Signed-hostap: Jouni Malinen <j@w1.fi>
Multiple memcmps of nonces were actually comparing only the first byte
instead of all 16 bytes. [Bug 462]
Signed-hostap: Eyal Shapira <eyal@wizery.com>
intended-for: hostap-1
There is no need to mandate admission control (ACM=1) by default, so
clear that flag in the case the configuration file does not specify
wmm_ac_{vo,vi}_acm value. This gets closer to the values mentioned
in the sample hostapd.conf file and reduces the need to specify WMM
parameters in the configuration file for most common use cases.
Signed-hostap: Jouni Malinen <j@w1.fi>
p2p_set_timeout() calls in GO Neg Req/Resp TX callbacks used timeout of
100 ms which is the value given in the P2P specification for GO
Negotiation, but this was actually shorter than the
wait-for-offchannel-TX value (200 ms) used for the driver call. In
addition, it looks like some devices (e.g., Galaxy Nexus with JB image)
can take longer time to reply to GO Negotiation Response (somewhere
between 200 and 250 ms has been observed).
Increase the wait-for-GO-Neg-Resp timeout from 100 ms to 200 ms if GO
Negotiation Request frame was acknowledged (this matches with the
offchannel wait timeout that used previously). The no-ack case is left
at 100 ms since we use GO Negotiation Request frame also to discover
whether the peer is on its Listen channel.
Increase the wait-for-GO-Neg-Conf timeout from 100 ms to 250 ms (and
increase the offchannel wait timeout to matching 250 ms) as a workaround
for devices that take over 200 ms to reply to GO Negotiation Response.
Signed-hostap: Jouni Malinen <j@w1.fi>
The commit b5fd8b1833
"VHT: Do not allow use of TKIP with VHT" introduced
an off-by-one regression: a WPA/RSN 11n AP would no
longer accept stations to connect, instead it would
produce a bogus error message:
... Station tried to use TKIP with HT association.
Signed-hostapd: Christian Lamparter <chunkeey@googlemail.com>
cur_pmksa was left to NULL during the initial association. This can
result in unexpected behavior, e.g., in expiring PMKSA cache entries
since the current entry is not locked in that case. Fix this by updated
cur_pmksa when adding the initial PMKSA entry during msg 1/4 processing.
Signed-hostap: Jouni Malinen <j@w1.fi>
intended-for: hostap-1
If the PMKSA cache is full (i.e., 32 candidates have been seen in scan
results and have not yet expired) then any additional entries can
potentially evict the current/active entry (if it is the oldest entry),
which triggers a pointless local deauthentication. The supplicant
shouldn't replace the current/active entry if it is still valid, but
instead the oldest entry that is *not* the current/active one.
Signed-hostap: Dan Williams <dcbw@redhat.com>
intended-for: hostap-1
When using multiple VLANs, GKeyDoneStations counter is not updated
properly since wpa_auth_for_each_sta() call in wpa_group_setkeys() ends
up iterating through all STAs and not just the STAs of a specific
wpa_group (VLAN). Consequently, GTK rekeying gets initialized multiple
times if more than a single group state machine exists. Fix this by
iterating only through the STAs in the specific wpa_group.
Signed-hostap: Michael Braun <michael-dev@fami-braun.de>
intended-for: hostap-1
CONFIG_VLAN_NETLINK=y build option can now be used to replace the
ioctl()-based interface for creating and removing VLAN interfaces
with netlink-based interface.
Signed-hostap: M. Braun <michael-dev@fami-braun.de>
Commit a11241fa11 removed the 802.11b rate
enabling/disabling code from wpa_driver_nl80211_set_mode() and while
doing that, removed the only place where drv->disabled_11b_rates was
set. Fix this by updating the flag in nl80211_disable_11b_rates(). In
addition, re-enable the 802.11b rates when changing to non-P2P mode.
Signed-hostap: Jouni Malinen <j@w1.fi>
Right now 11b rates are masked out while creating a P2P interface,
but this is always failing as the interface is down. Most drivers
allow to configure rates only when the interface is UP and running.
So let us disable 11b rates when interface type is changed into a
P2P type and it is UP and running.
Signed-hostap: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
These validation steps are already done in the EAP parsing code and in
the EAP methods, but the additional check is defensive programming and
can make the validation of received EAP messages more easier to
understand.
Signed-hostap: Jouni Malinen <j@w1.fi>
These checks would not really be needed since eapol_sm_rx_eapol()
validates the length fields. Anyway, these makes it more obvious to
anyone reviewing the code that there are no integer underflow issues in
processKey().
Signed-hostap: Jouni Malinen <j@w1.fi>
These checks would not really be needed since radius_msg_parse()
validates the attribute header fields. Anyway, these makes it more
obvious to anyone reviewing the code that there are no integer underflow
issues in the functions processing RADIUS attributes.
Signed-hostap: Jouni Malinen <j@w1.fi>
This simplifies the implementation by using the buffer type to which the
returned data will be converted anyway. This avoids one memory
allocation for each processed RADIUS message.
Signed-hostap: Jouni Malinen <j@w1.fi>
Couple of functions did not verify that nla_put_nested() succeeded. Fix
these by checking the return value and handling error cases cleanly.
Signed-hostap: Jouni Malinen <j@w1.fi>
The new ssid2 parameter can be used as an alternative mechanism for
configuring SSID for hostapd. It uses the same formats that
wpa_supplicant uses in the configuration file for strings.
Signed-hostap: Jouni Malinen <j@w1.fi>
Instead of masking out non-ASCII characters with underscores, espace the
SSID data using rules compatible with printf.
Signed-hostap: Jouni Malinen <j@w1.fi>
This can be used to build ASCII strings from binary data that is
more likely to use ASCII (i.e., text format is more natural
option than hexdump, but there is possibility of some non-ASCII
characters).
Signed-hostap: Jouni Malinen <j@w1.fi>
When CONFIG_CTRL_IFACE=udp-remote is used, print user frendly PS in
wpa_cli. E.g.,
localhost/wlan0>
192.168.1.1/p2p-wlan-0-0>
Signed-hostap: Janusz Dziedzic <janusz.dziedzic@tieto.com>
wpa_cli can be used now as a client for remote access to ctrl_interface
of wpa_supplicant when UDP and remote options are used.
You can simply run:
wpa_cli -i <hostname>:[port]
wpa_cli -i <IP>:[port]
Signed-hostap: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Add new option for ctrl iface: CONFIG_CTRL_IFACE=udp-remote. This
enables remote access to control interface via UDP port(s). This should
be used for testing purpose only since there is no authentication or
access control on the commands.
Signed-hostap: Janusz Dziedzic <janusz.dziedzic@tieto.com>
This bit is set in the code path that handles keys and certs from places
other than OpenSSL authentication engines. Setting this bit causes
authentication to fail when the server provides certificates that don't
match the client certificate authority.
Commit 05ab9712b9 added support for
fetching WPA PSK from an external RADIUS server and changed
hostapd_wpa_auth_get_psk() to always return the RADIUS supplied PSK (if
set) and ignore the prev_psk parameter for iteration. Fix this by
appending the RADIUS supplied PSK to the list iterated by
hostapd_get_psk and thus returning NULL when prev_psk == sta->psk
(RADIUS).
Signed-hostap: M. Braun <michael-dev@fami-braun.de>
This allows the password parameter for EAP methods to be fetched
from an external storage.
Following example can be used for developer testing:
ext_password_backend=test:pw1=password|pw2=testing
network={
key_mgmt=WPA-EAP
eap=TTLS
identity="user"
password=ext:pw1
ca_cert="ca.pem"
phase2="auth=PAP"
}
Signed-hostap: Jouni Malinen <j@w1.fi>
This new mechanism can be used to make wpa_supplicant using external
storage (e.g., key store in the operating system) for passwords,
passphrases, and PSKs. This commit is only adding the framework part
needed to support this, i.e., no actual configuration parameter can
yet use this new mechanism. In addition, only a simple test backend
is added to allow developer testing of the functionality.
Signed-hostap: Jouni Malinen <j@w1.fi>
This allows the SA Query mechanism in hostapd to be used with drivers
that implement authentication and association MLME/SME.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
disable_dgaf=1 in hostapd.conf can now be used to disable downstream
group-addressed forwarding (DGAF). In this configuration, a unique
GTK (and IGTK) is provided to each STA in the BSS to make sure the
keys do not match and no STA can forge group-addressed frames.
An additional mechanism in the AP needs to be provided to handle some
group-addressed frames, e.g., by converting DHCP packets to unicast
IEEE 802.11 frames regardless of their destination IP address and by
providing Proxy ARP functionality.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Allow the user to configure an RSSI threshold in dBm below which the
nl80211 driver won't report scan results. Currently only supported
during scheduled (PNO) scans.
Signed-off-by: Thomas Pedersen <c_tpeder@qca.qualcomm.com>
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Commit 6b56cc2d97 added retries of
provision discovery request frames in IDLE state. However, it did not
make the p2p_find case behave consistently with the new limitied retry
behavior. This can result in way too many and frequent PD retries. Fix
this by extending the previous commit to address PD retries and maximum
retry limit consistently regardless of whether p2p_find is running.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
intended-for: hostap-1
Commit 1b487b8b1e added CH_SWITCH
event for nl80211, but ended up using hostapd_hw_get_channel()
regardless of build configuration for driver interfaces. This
function is not always available, so make its use conditional
on NEED_AP_MLME.
Signed-hostap: Jouni Malinen <j@w1.fi>
Commit d9cc4646eb added
crypto_hash_{init,update,finish}() wrappers for OpenSSL, but it
assumed the current HMAC API in OpenSSL. This was changed in 0.9.9
to return error codes from the functions while older versions used
void functions. Add support for the older versions, too.
Signed-hostap: Jouni Malinen <j@w1.fi>
This patch adds a check of the return value of wpabuf_dup() in a large
Service Discovery Response.
Signed-hostap: Masashi Honma <masashi.honma@gmail.com>
This updates the license notification to use only the BSD license. The
changes were acknowledged by email (Gunter Burchardt, tmisu@gmx.de,
Mon, 02 Jul 2012 17:54:28 +0200).
Signed-hostap: Jouni Malinen <j@w1.fi>
This updates the license notification to use only the BSD license. The
changes were acknowledged by email (Jouke Witteveen
<j.witteveen@gmail.com>, Mon, 2 Jul 2012 11:38:34 +0200).
Signed-hostap: Jouni Malinen <j@w1.fi>
This functionality could be shared for other commands, too, so move
it to a common function. In addition, implement the validation in a
bit more strict way to avoid accepting values like '-123' as a valid
PIN.
Signed-hostap: Jouni Malinen <j@w1.fi>
There are separate states for these, so we can't really get into this
situation unless somebody tries to do multiple things at the same
time. p2p_connect stops find and CONNECT state is used to probe the peer
on its Listen channel with GO Negotiation Request frames. Similarly,
p2p_invite() stops find and INVITE state is used to probe the peer on
its Listen channel with Invitation Request frames. The older mechanism
of using Search state functionality to find the peer can be removed.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This updates these files to use the license notification that uses only
the BSD license. The changes were acknowledged by email (Sam Leffler
<sam@errno.com>, Sat, 30 Jun 2012 07:57:53 -0700).
Signed-hostap: Jouni Malinen <j@w1.fi>
At least some error paths (e.g., hitting the limit on hunt-and-peck
iterations) could have resulted in double-freeing of some memory
allocations. Avoid this by setting the pointers to NULL after they have
been freed instead of trying to free the data structure in a location
where some external references cannot be cleared. [Bug 453]
Signed-hostap: Jouni Malinen <j@w1.fi>
The previously used limit (10) is too small for practical purposes since
it can result in about 1 out of 1000 authentication attempts failing.
Increase the limit to 30 to avoid such issues. [Bug 453]
Signed-hostap: Jouni Malinen <j@w1.fi>
intended-for: hostap-1
os_random() may not be seeded properly, so use stronger mechanism for
generating the password id for NFC password tokens.
Signed-hostap: Jouni Malinen <j@w1.fi>
The new hostapd ctrl_iface command WPS_NFC_TOKEN can now be used to
manage AP-as-Enrollee operations with NFC password token. WPS/NDEF
parameters to this command can be used to generate a new NFC password
token. enable/disable parameters can be used to enable/disable use of
NFC password token (instead of AP PIN) for external Registrars.
A preconfigured NFS password token can be used by providing its
parameters with new hostapd.conf fields wps_nfc_dev_pw_id,
wps_nfc_dh_pubkey, wps_nfc_dh_privkey, and wps_nfc_dev_pw. This use
will also depend on WPS_NFC_TOKEN enable/disable commands, i.e., the
configured NFS password token is disabled by default.
Signed-hostap: Jouni Malinen <j@w1.fi>
The AP PIN on wps_reg command can now be replaced with special value
"nfc-pw" to use device password from a NFC password token from the AP.
Signed-hostap: Jouni Malinen <j@w1.fi>
WPS_ER_NFC_CONFIG_TOKEN command can now be used to build a NFC
configuration token based on AP Settings learnt with WPS_ER_LEARN
or set with WPS_ER_CONFIG.
Signed-hostap: Jouni Malinen <j@w1.fi>
The new wpa_supplicant ctrl_iface command WPS_NFC_TAG_READ can now be
used to process NFC tags read by external programs to initiate
wpa_supplicant to use NFC Configuration Token to create a new network.
Signed-hostap: Jouni Malinen <j@w1.fi>
The new hostapd ctrl_iface command WPS_NFC_CONFIG_TOKEN can now be used
to fetch payload for an NFC configuration token so that an external
program can be used to write this on an NFC tag.
Signed-hostap: Jouni Malinen <j@w1.fi>
This adds a cleaner mechanism for handling NFC Password Tokens in the
WPS Registrar. There could be more than one active NFC Password Token in
use and as such, a list of tokens needs to be maintained. The old
WPS_OOB interface is still using the old mechanism that supports only a
single active NFC Password Token.
Signed-hostap: Jouni Malinen <j@w1.fi>
hostapd ctrl_iface can now be used to deliver payload from read
operation of an NFC tag. This allows operations without having to have
low-level NFC code within hostapd. For now, the new wps_nfc_tag_read
command can be used with NFC password tokens for the case where the AP
has an NFC device that is used to read an NFC tag from the station
Enrollee.
Signed-hostap: Jouni Malinen <j@w1.fi>
Instead of requiring low-level access to an NFC device and synchronous
operations, the new WPS_NFC_TOKEN and WPS_NFC ctrl_iface commands can be
used to build a NFC password token and initiate WPS protocol run using
that token (or pre-configured values) as separate commands. The
WPS_NFC_TOKEN output can be written to a NFC tag using an external
program, i.e., wpa_supplicant does not need to have low-level code for
NFC operations for this.
Signed-hostap: Jouni Malinen <j@w1.fi>
The OOB Device Password is passed in as a hexdump of the real Device
Password (16..32 octets of arbitrary binary data). The hexdump needs to
be converted to binary form before passing it for WPS processing.
Signed-hostap: Jouni Malinen <j@w1.fi>
Previously, only the maximum length 32 octets for OOB device password
was accepted. Since the specification allows a shorter password to be
used with limited OOB mechanism (e.g., small NFC tag), we should accept
lengths 16..32.
Signed-hostap: Jouni Malinen <j@w1.fi>
The earlier WPS 2.0 changes did not increase the wpabuf size when
adding a new attribute to the NFC password token. This could result
in aborting the application on wpabuf overflow if NFC out-of-band
mechanism is used with WPS 2.0 enabled.
Signed-hostap: Jouni Malinen <j@w1.fi>
intended-for: hostap-1
Some drivers may independently decide to switch channels. Handle this by
updating the hostapd and wpa_supplicant AP and GO configuration.
Signed-hostap: Thomas Pedersen <c_tpeder@qca.qualcomm.com>
Previously, the STA entry was removed only from the driver and the STA
entry within hostapd was just marked disassociated. However, this left
the WPA authenticator state machine with an entry and the session was
not terminated properly. In addition, the STA entry could have remaining
indefinitely if the STA did not reconnect after TKIP countermeasures.
Fix this by removing the STA entry from hostapd instead of just leaving
it disassociated.
Signed-hostap: Jouni Malinen <j@w1.fi>
In AP which supports WPSv2 with only virtual push button, when PBC is
called, the WSC IE should include Selected Registrar Configuration
Methods attribute with the bit of the physical push button not set.
Signed-hostap: Yoni Divinsky <yoni.divinsky@ti.com>
Without this, we can get into a tight loop because the
code in general doesn't add eloop exception handlers,
so socket reporting the POLLERR would never be read.
With this change, any socket with POLLERR or POLLHUP
asserted will be handled by the read logic.
Signed-hostap: Ben Greear <greearb@candelatech.com>
The control message received from the kernel needs some space, but
there's no need for the strange typing that breaks clang compilation.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
Maintain a copy of Chargeable-User-Identity in the PMKSA cache to allow
it to be included in accounting messages even if full authentication was
not completed.
Signed-hostap: Jouni Malinen <j@w1.fi>
Calling-Station-Id, Acct-Session-Id, and User-Name attributes in a
Disconnect-Request message can now be used to indicate which station is
to be disconnected.
Signed-hostap: Jouni Malinen <j@w1.fi>
DAS will now validate Event-Timestamp value to be within an acceptable
time window (300 seconds by default; can be set using
radius_das_time_window parameter). In addition, Event-Timestamp can be
required in Disconnect-Request and CoA-Request messages with
radius_das_require_event_timestamp=1.
Signed-hostap: Jouni Malinen <j@w1.fi>
Currently, FullMAC Persistent GO can't use p2p_client_list because its
own hapd->p2p_group is NULL at ap_sta_set_authorized(). This patch
changes the processing to use sta->p2p_ie instead of
p2p_group_get_dev_addr() on FullMAC GO.
Signed-hostap: Masashi Honma <masashi.honma@gmail.com>
The P2P Client Discoverability bit is reserved in most frames and its
value in the local P2P peer table should only be updated based on P2P
Group Info attribute from a GO. Fix this by avoiding changes to this
dev_capab bit based on other P2P frames. It would be more correct to
track this separately for each group in which the peer is a member, but
since we do not do that for the other group specific information either,
this can do for now.
It should be noted that prior to commit
18485b5469 wpa_supplicant set this bit in
all P2P frames. However, that commit changed this to match the
specification, i.e., the bit is not set in frames which are received
from P2P Device role. As such, this fix is needed to be able to figure
out that a peer supports client discoverability capability after that
commit.
Signed-hostap: Jouni Malinen <j@w1.fi>
intended-for: hostap-1
In the P2P specification v1.1, the P2P Client Discoverability bit is
described in Table 12 "Device Capability Bitmap definition". The table
says "Within a P2P Group Info attribute and a (Re)association request
frame the P2P Client Discoverability field shall be set to 1 when the
P2P Device supports P2P Client Discoverability, and is set to 0
otherwise. This field shall be reserved and set to 0 in all other frames
or uses.". To match with this, filter out P2P Client Discoverability bit
from frames where its use is reserved.
Signed-hostap: Masashi Honma <masashi.honma@gmail.com>
If the peer uses an unknown reauth id, it would still be possible to use
pseudonym instead of permanent id. Allow this by changing the
AT_PERMANENT_ID_REQ to AT_FULLAUTH_ID_REQ in case unknown reauth id is
used in EAP-Response/Identity.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
There is a race condition in GO Negotiation Request frame sending and
processing that may end up with both devices sending GO Negotiation
Response. This response frame was previously accepted even if a response
had already been sent. This could result in two GO Negotiation Confirm
frames being exchanged and consequently, with two separate GO
Negotiations completing concurrently. These negotiations could result in
getting mismatching parameters (e.g., both device could believe it was
the GO).
Fix this by ignoring GO Negotiation Response from the peer if twe have
already sent a GO Negotiation Response frame and we have the higher P2P
Device Address. This is similar to the rule used to determine whether to
reply to GO Negotiation Request frame when Request was already sent,
i.e., the same direction of GO Negotiation is maintained here to enforce
that only the negotiation initiated by the device with smaller P2P
Device Address is completed.
Signed-hostap: Jouni Malinen <j@w1.fi>
intended-for: hostap-1
If both peers initiate GO Negotiation at about the same time, it is
possible for the GO Negotiation Request frame from the peer to be
received between the local attempt to send the GO Negotiation Request
and TX status event for that. This could result in both devices sending
GO Negotiation Response frames even though one of them should have
skipped this based which device uses a higher MAC address.
Resolve this race by incrementing go_neg_req_sent when p2p_send_action()
returns success instead of doing this from the TX status callback. If
the frame is not acknowledged, go_neg_req_sent is cleared in TX status
handler.
Signed-off-by: Neeraj Garg <neerajkg@broadcom.com>
Stop the connection attempt if GO Negotiation Confirm is not received
within 100 ms of the GO Negotiation Response getting acknowledged.
Previously, we would have continued trying to connect to the peer even
in this case which could result in confusing second GO Negotiation
Request frame and unnecessarily long wait before indicating failure.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The GO Negotiation Confirm frame doesn't need to be sent with a wait
since we don't expect a response to it.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
Concurrent Operation bit was not set for GO even if the device
supports concurrent operations. Make sure the Device Capability
value is consistent with other P2P use cases by using the value
determined in p2p_init().
Signed-hostap: Masashi Honma <masashi.honma@gmail.com>
Send an "EAP" signal via the new DBus interface under various
conditions during EAP authentication:
- During method selection (ACK and NAK)
- During certificate verification
- While sending and receiving TLS alert messages
- EAP success and failure messages
This provides DBus callers a number of new tools:
- The ability to probe an AP for available EAP methods
(given an identity).
- The ability to identify why the remote certificate was
not verified.
- The ability to identify why the remote peer refused
a TLS connection.
Signed-hostap: Paul Stewart <pstew@chromium.org>
In certain cases like PBC session overlap it appears to be possible that
an interface is removed due to an event handled on it, this leads to
list corruption. Use safe iteration to prevent this issue.
Reported-by: Nirav Shah <nirav.j2.shah@intel.com>
Reported-by: Neeraj Kumar Garg <neerajkg@broadcom.com>
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
intended-for: hostap-1
When hostapd (or wpa_supplicant AP mode) limits the maximum number
of STA entries with a driver that implements SME, the driver needs
to be notified of the failed STA addition. Disassociate the STA if
the driver notifies of an association that would go beyond the
maximum number of STAs.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
If WNM is enabled for the build (CONFIG_WNM=y), add BSS max idle period
information to the (Re)Association Response frame from the AP and parse
this information on the station. For SME-in-wpa_supplicant case, add a
timer to handle periodic transmission of the keep-alive frame. The
actual request for the driver to transmit a frame is not yet
implemented.
Signed-hostap: Jouni Malinen <j@w1.fi>
When sending an offchannel frame (mainly, P2P Invitation Request), the
wait_time parameter was hardcoded to 0 for drivers that implement AP
mode SME. This is not correct and can cause problems for drivers that
support offloading of off-channel operations with driver/firmware based
AP SME.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This is a workaround for interoperability issues with some deployed P2P
implementations that require a Provision Discovery exchange to be used
before GO Negotiation. The new provdisc parameter for the p2p_connect
command can be used to request this behavior without having to run a
separate p2p_prov_disc command.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The nl80211 driver interface does not allow 128-bit WEP to be used
without a vendor specific cipher suite and no such suite is defined for
this purpose. Do not accept WEP key length 16 for nl80211 driver
interface forn ow. wext-interface can still try to use these for
backwards compatibility.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
If the AP indicates support for Hotspot 2.0, show this in the
ctrl_iface commands for BSS table and status.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
If PD Request includes P2P Group ID, verify that the specified
group matches with a group we are currently operating. If no match
is found, reject the PD Request for join-a-group case.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This can be used with P2P management operations that need to verify
whether the local device is operating a specific group based on
P2P Group ID attribute from a peer.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Commit 349b213cc8 added a separate
callback prov_disc_fail() for indicating PD failures, but it left the
Provision Discovery Response handler to call both callbacks in case the
peer rejected the PD. Commit f65a239ba4
added ctrl_iface event for PD failures. This combination can result in
two ctrl_iface events in the peer rejecting a PD case. Clean this up by
only indicating the failure event.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Some drivers may accept the remain-on-channel command, but instead of
indicating start event for remain-on-channel, just indicate that the
operation has been canceled immediately. This could result in continuous
loop of search/listen states with very limited time to do anything else
in wpa_supplicant if the scan command is also completed quickly (e.g.,
if the driver is unable to scan other channels than the current
operating channel).
As a workaround, do not start the next step (search) in P2P device
discovery if this type of rejection of listen operation is detected.
This gives some more time for wpa_supplicant to handle whatever else
may be needed at to be done at the same time and reduces the amount
of CPU used in a loop that does not really work correctly from the
view point of being discoverable.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
intended-for: hostap-1
This adds the basic DAS mechanism to enable hostapd to be configured
to request dynamic authorization requests (Disconnect-Request and
CoA-Request). This commit does not add actual processing of the
requests, i.e., this will only receive and authenticate the requests
and NAK them regardless of what operation is requested.
Signed-hostap: Jouni Malinen <j@w1.fi>
New configuration parameters radius_auth_req_attr and
radius_acct_req_attr can now be used to add (or override) RADIUS
attributes in Access-Request and Accounting-Request packets.
Signed-hostap: Jouni Malinen <j@w1.fi>
radius_request_cui=1 configuration parameter can now be used to
configure hostapd to request CUI from the RADIUS server by including
Chargeable-User-Identity attribute into Access-Request packets.
Signed-hostap: Jouni Malinen <j@w1.fi>
If Access-Accept packet includes the Chargeable-User-Identity attribute,
copy this attribute as-is into accounting messages.
Signed-hostap: Jouni Malinen <j@w1.fi>
There was a technical change between the last IETF draft version
(draft-arkko-eap-aka-kdf-10) and RFC 5448 in the leading characters
used in the username (i.e., use unique characters for EAP-AKA' instead
of reusing the EAP-AKA ones). This commit updates EAP-AKA' server and
peer implementations to use the leading characters based on the final
RFC.
Note: This will make EAP-AKA' not interoperate between the earlier
draft version and the new version.
Signed-hostap: Jouni Malinen <j@w1.fi>
intended-for: hostap-1
Incorrect identity string could end up being used with EAP-AKA' when
the EAP client is using pseudonym. This code was supposed to use
sm->identity just like the EAP-AKA case.
Signed-hostap: Jouni Malinen <j@w1.fi>
intended-for: hostap-1
The misplaced parenthesis caused Device ID matching to check only the
first octet of the P2P Device Address, i.e., we could have replied to
Probe Request frames that was searching for another device if any of
the last five octets of the address were different.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
intended-for: hostap-1
An existing persistent group information can now be used to force GO
Negotiation to use the previously used SSID/passphrase from a persistent
group if we become a GO. This can be used as an alternative to inviting
a new P2P peer to join the group (i.e., use GO Negotiation with GO
intent 15 instead of starting an autonomous GO and using invitation),
e.g., in case a GO Negotiation Request is received from a peer while we
are not running as a GO. The persistent group to use for parameters is
indicated with persistent=<network id> parameter to p2p_connect.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Commits 17bef1e97a and
ffe98dfb88 started using p2p_add_device()
with other frames than just Probe Response frames from scan results.
However, these changes did not take into account that the PD Request
and Invitation Request frames are normally received on the our own
Listen channel, not on the Listen channel of the peer. As such, these
frames must not be used to update Listen channel information for the
peer.
Fix this by letting p2p_add_device() know whether the results are from
scan results and if not, skip the peer table updates that are specific
to Probe Response frames.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
intended-for: hostap-1
Add provisional discovery failure ctrl_iface event
(P2P-PROV-DISC-FAILURE) to indicate to the application layer in case of
PD failure.
Signed-off-by: Deepthi Gowri <deepthi@codeaurora.org>
Commit d9bdba9f86 was supposed to allow
p2p_listen to schedule new after scan operation only if a p2p_connect
operation was not pending. However, it used incorrect P2P_AFTER_SCAN_
value for this and did not actually prevent overriding of p2p_connect
and could have caused some p2p_listen operations to be skipped
unnecessarily.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
intended-for: hostap-1
Unlike the unicast SD queries, the queries directed to all peers depend
on P2P_DEV_SD_INFO flag being cleared to allow the query to be sent to
a peer that has previously replied to any SD query.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Previously, the timeout scheduled during the previous association was
used after reassociation if the STA entry had not yet been removed. The
next timeout does not need to happen that quickly, so reschedule it
during reassociation.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This makes it easier to figure out what exactly was done with the
ap_handle_timer registration/cancellation based on a debug log.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The next ap_handle_timer action was already cleared when association
is handled with user space -based SME. However, this step was missing
from the driver callback for indicating new association. This could
result in the first ap_handle_timer timeout on the new association
removing the station unexpectedly. Fix this by resetting the timeout_next
in hostapd_notif_assoc().
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
intended-for: hostap-1
A station may move from EAP/WPS key_mgmt to PSK using re-association. In
practice, this can happen most likely with WPS when the station runs
through the provisioning step (EAP/WPS) followed by PSK authentication.
If a deauthentication event is missed from the station for whatever
reason, the EAPOL authenticator state machine could have been left
running.
This can result in various issues, including unexpected disconnection of
the station while both the 4-way handshake and EAPOL authenticator state
machines (EAP) are running at the same time when the supplicant is
trying to use PSK. Fix this by explicitly clearing EAPOL authenticator
state machine on (re)association if the new association does not use it.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
intended-for: hostap-1
When starting an AP with HT40 on 2.4 GHz, limit the set of channels
to scan for based on the affected frequency range to speed up the
AP setup.
Signed-hostap: Jouni Malinen <j@w1.fi>
Mark the debug print excessive and print it only in case the entropy
collection is used since this function can get called pretty frequently.
Signed-hostap: Jouni Malinen <j@w1.fi>
OpenSSL wrapper was using the same certificate store for both Phase 1
and Phase 2 TLS exchange in case of EAP-PEAP/TLS, EAP-TTLS/TLS, and
EAP-FAST/TLS. This would be fine if the same CA certificates were used
in both phases, but does not work properly if different CA certificates
are used. Enforce full separation of TLS state between the phases by
using a separate TLS library context in EAP peer implementation.
Signed-hostap: Jouni Malinen <j@w1.fi>
This was never really completed and is of not much use at this point,
so clean up the repository by removing the Symbian-specific changes.
Signed-hostap: Jouni Malinen <j@w1.fi>
This optional parameter to the BSS command can be used to select which
fields are included in the output to avoid having to parse through
unneeded information and to reduce the buffer size.
Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
There is no need to subscribe to event messages during deinit process,
so skip this to avoid unnecessary operations and to keep the debug logs
a bit cleaner.
Signed-hostap: Jouni Malinen <j@w1.fi>
This should keep us from getting into a state where we bounce large
numbers of stations all at once. Spreading out the bounce should cause
less stress on the network as the idle stations won't all be trying to
reconnect at once.
Signed-hostap: Ben Greear <greearb@candelatech.com>
wps_vendor_ext_m1 configuration parameter can now be used to add a
vendor specific attribute into the WPS M1 message, e.g., for
Windows Vertical Pairing.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This was previously indicated as disassociation, but the P2P group
session ending case expect a deauthentication notification. Since the
cfg80211 disconnection event does not really indicate which frame was
used, the easiest approach for now seems to be to just indicate these
as deauthentication events.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Use reason code 3 (Deauthenticated because sending STA is leaving)
instead of reason code 2 (Previous authentication ot valid) in the
Deauthentication frame sent at the time a BSS is terminated. This is
more accurate reason for the message and allows the stations to get
better understand on why they were disconnected. This can be useful
especially for P2P clients that can use this as a signal that the
P2P group session was ended per P2P specification section 3.2.9.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
On P2P group removal, the GO is deinitialized correctly (and the vif
mode is set back to sta in case of nl80211), but the P2P client mode
wasn't deinitialized, and the nl80211 vif stays in P2P client mode.
Add a new deinit_p2p_cli op (similar to deinit_ap), which currently only
sets the interface back to station mode.
Signed-hostap: Eliad Peller <eliad@wizery.com>
intended-for: hostap-1
Some applications require knowing about probe requests to identify
devices. This can be the case in AP mode to see the devices before they
connect, or even in P2P mode when operating as a P2P device to identify
non-P2P peers (P2P peers are identified via PeerFound signals).
As there are typically a lot of probe requests, require that an
interested application subscribes to this signal so the bus isn't always
flooded with these notifications. The notifications in DBus are then
unicast only to that application.
A small test script is also included.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
The signal strength is currently never used as the only driver reporting
it is nl80211 which uses IEEE80211_RADIOTAP_DB_ANTSIGNAL which is never
populated by the kernel. The kernel will (soon) populate
IEEE80211_RADIOTAP_DBM_ANTSIGNAL instead though, so use that.
Also, since it was never really populated, we can redefine the signal
field to be in dBm units only.
My next patch will also require knowing the signal strength of probe
requests throughout the code (where available), so add it to the
necessary APIs.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
When hostapd is about to start an AP using HT40, it starts a scan to
check whether it is allowed or not. If OLBC is detected before the
scan has completed, it sets the beacons prematurely.
To fix this, instead of setting all beacons when OLBC is detected,
only update the ones that have already been started.
Signed-off-by: Luciano Coelho <coelho@ti.com>
ieee802_1x_encapsulate_radius() frees the RADIUS message if
radius_client_send() returns error. This could have resulted in use of
freed memory and double freeing of the RADIUS message if send() fails
since the message is also left in the retransmit list. Avoid this by not
returning error to the caller in such a case.
Signed-off-by: Alexander Couzens <lynxis@c-base.org>
Add the option (-T) to wpa_supplicant to log all debug messages into the
kernel tracing, allowing to aggregate kernel debugging with
wpa_supplicant debugging and recording all with trace-cmd.
Since tracing has relatively low overhead and can be filtered
afterwards, record all messages regardless of log level. However, it
will honor the -K option and not record key material by default.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
The "BSS p2p_dev_addr=address" command uses p2p_parse_dev_addr() to
figure out the P2P Device Address of the GO from scan results. This used
to work only if the P2P IE was received from Probe Response frames since
only those include the P2P Device Info attribute. Make this work with
Beacon frames, too, by using P2P Device ID attribute if the P2P Device
Info attribute is not present.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
A network block specific background scan period can now be configured
for drivers that implement internal background scan mechanism for
roaming and BSS selection.
Signed-hostap: Bala Shanmugam <bkamatch@qca.qualcomm.com>
Implement wps_cancel for hostapd similarly to how it was already
supported in wpa_supplicant AP mode.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
p2p_pref_chan configuration parameter can now be used to set the
list of preferred channel for P2P GO Negotiation. This will be used
in the priority order if the peer does not support the channel we
are trying to use as the GO (configured operating channel or the
best 2.4 GHz/5 GHz channel) for the case where a forced channel is
not used.
p2p_pref_chan=<op class:channel>,...
For example:
p2p_pref_chan=81:1,81:2,81:3,81:4,81:5,81:6
This would configure 2.4 GHz channels 1-6 as the preferred ones with
channel 1 the most preferred option.
These configuration parameters can be set in wpa_supplicant.conf and
dynamically updated with "wpa_cli set <param> <value>".
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
When drivers advertise their capability to free up inactive
stations based on ap_max_inactivity, send the inactivity period
timeout to driver in NL80211_ATTR_INACTIVITY_TIMEOUT. This
introduces a WPA_DRIVER_FLAGS (WPA_DRIVER_FLAGS_INACTIVITY_TIMER)
so that the inactivity period will be sent only when this capability
bit is set.
Signed-hostap: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
When the driver (or firmware) implements AP mode SME, the use of raw
management frame TX functions is not working properly at the moment. As
an initial step, convert these AP mode operations to use
NL80211_CMD_DEL_STATION and do not claim that driver provides TX status
for deauth/disassoc frames. While this does not address all use cases
(e.g., reason code is not specified in the command), this fixes number
of issues where the station does not get disconnected properly.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Commit 30680e9332 changed the length
of the implicit challenge result to match with the exact length used
in TTLS. However, it failed to update the peer_challenge generation
to use a separate random value. Previously, this was generated as
part of the implicit challenge, but more correct way would have been
to generate a random value for it separately. Do this now to fix the
read after the allocated buffer (16 bytes after the implicit
challenge).
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
intended-for: hostap-1
This DO has a maximum length of 127 bytes (TS 102 221), so better use
large enough buffer when reading the record.
Signed-hostap: Jouni Malinen <j@w1.fi>
Previously, this provisioning info was cleared using the P2P Interface
Address of the GO as the key. That did not always work in the case the
where we joined an already running group. This could result in the next
connection to that same GO skipping provision discovery. Fix this by
finding the peer entry based on its P2P Device Address instead of the
P2P Interface Address which may not always be set.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
intended-for: hostap-1
If a wildcard PIN is used on any of the radios that hostapd is
controlling, invalidate the matching PIN on all the other radios
to avoid multiple uses of the same PIN.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Use Device Password ID in WSC IE of Probe Request and Probe Response
frames to advertise immediate availability of WPS credentials per P2P
specification sections 3.1.2.1.1 (Listen State), 3.1.2.1.2 (Scan Phase),
and 3.1.2.1.3 (Find Phase).
For now, the Device Password ID is set only for the case where we are
active GO Negotiation with a specific peer. In practice, this means that
the Probe Response frames during pending GO Negotiation (whenever in
Listen state) indicate availability of the credential.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
p2p_flush did not explicit stop all P2P operations, i.e., the exact
behavior depended on the P2P module state at the time the p2p_flush
command was issued. Make this more consistent by explicitly calling
p2p_stop_find() from p2p_flush().
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
If Listen state was in progress on another channel when a request to
send an Action frame (e.g., Provision Discovery Request or Invitation
Request to a peer on the peer's Listen channel that is different from
our Listenc hannel) is issued, wpa_supplicant tried to use concurrent
remain-on-channel operations. While some drivers can handle this
cleanly, there are drivers that don't and wpa_supplicant is not expected
to request concurrent remain-on-channel operations.
Fix this by cancelling the ongoing remain-on-channel with stop_listen
prior to sending the Action frame on another channel. If a P2P search
was in progress, it will be continued after the timeout on the new
operation.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The new venue_name configuration parameter can now be used to configure
the ANQP Venue Name values that stations can request through GAS.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This adds GAS/ANQP implementation into hostapd. This commit brings in
the basic GAS/ANQP functionality, but only the ANQP Capability List
element is supported.
For testing purposes, hostapd control interface SET command can be used
to set the gas_frag_limit parameter dynamically.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
New global configuration parameters pcsc_reader and pcsc_pin can now be
used to initialize PC/SC reader context at start of wpa_supplicant.
Signed-hostap: Jouni Malinen <j@w1.fi>
Definition of ANonce selection in IEEE Std 802.11i-2004 is somewhat
ambiguous. The Authenticator state machine uses a counter that is
incremented by one for each 4-way handshake. However, the security
analysis of 4-way handshake points out that unpredictable nonces help in
preventing precomputation attacks. Instead of the state machine
definition, use an unpredictable nonce value here to provide stronger
protection against potential precomputation attacks.
Signed-hostap: Jouni Malinen <j@w1.fi>
Move disassociate and deauthenticate commands to ctrl_iface_ap.c, so
that they ares accessible for wpa_supplicant AP mode and wpa_cli (with
CONFIG_AP option enabled).
Signed-hostap: Jithu Jance <jithu@broadcom.com>
Remove unnecessary second copy of the URL and too long memory
allocation. In addition, avoid use of strcpy() to keep static analyzers
happier.
Signed-hostap: Jouni Malinen <j@w1.fi>
It looks like a RTM_NEWLINK event claiming the interface to be UP is
delivered just before removing an interface after having first indicated
that the interface was going down/removed. Ignore this event if the
interface is not present anymore at the moment the event is processed.
This fixes issues where an interface that was re-added after being
removed did not get reconfigured properly.
Signed-hostap: Jouni Malinen <j@w1.fi>
intended-for: hostap-1
It looks like a RTM_NEWLINK event claiming the interface to be UP is
delivered just before removing an interface after having first indicated
that the interface was going down/removed. Ignore this event if the
interface is not present anymore at the moment the event is processed.
This fixes issues where an interface that was re-added after being
removed did not get reconfigured properly.
Signed-hostap: Jouni Malinen <j@w1.fi>
intended-for: hostap-1
AT_NEXT_PSEUDONYM is supposed to be included only in the Challenge
messages, not in the Re-authentication messages. This attribute was
incorrectly included in the Re-authentication messages and could have
been used to update the pseudonym state on the server without the peer
updating its state.
Signed-hostap: Jouni Malinen <j@w1.fi>
intended-for: hostap-1
Add support to send Action frames to the driver.
Add support for TSPEC req and adding STA node to the driver.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
"wpa_cli set radio_disabled 1/0" can be used to disable/enable
radio to simulate out-of-radio-range condition in a testbed
device.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Commit d9a38716cc did this for
hostapd_eapol_tx_status() but missed the older hostapd_tx_status()
path. Address that case, too.
The TX status event may be received after a station has been
disassociated in cases where the disassociation is following a
transmission of a Data frame. Ignore such events if the STA is not
associated at the moment the event is being processed. This avoids
confusing debug entries and rescheduling of the EAPOL TX timeouts for
STAs that are still in the STA table, but are not really in active EAPOL
session.
Signed-hostap: Jouni Malinen <j@w1.fi>
intended-for: hostap-1
The SetSelectedRegistrar timeout was registered for each registrar
instance, but the only context pointer (struct subscription *) was
shared with each registrar which resulted in the timeout getting
cancelled for some of the registrar instances before the selected
registrar (ER) information was cleared.
In addition, when an ER unsubscribed from receiving events, the
selected registrar information got cleared only from a single
registrar.
Fix these issues by registering a pointer to the registrar
instance in the timeout and by iterating over all UPnP interfaces
when removing a subscription.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
eloop_sock_table_add_sock() needs to fail if pollfd array allocation
fails instead of returning success and leaving behind no buffer.
Signed-hostap: Jouni Malinen <j@w1.fi>
In IBSS RSN cfg80211/mac80211 now waits for userspace to authorize new
stations. This patch makes wpa_supplicant notify the driver when a
station can be considered authorized.
Signed-hostap: Antonio Quartulli <ordex@autistici.org>
When using more than around 200 virtual stations, we start hitting the
max number of file descriptors supported by select(). This patch adds
support for poll(), which has no hard upper limit.
Signed-hostap: Ben Greear <greearb@candelatech.com>
Remove the GPL notification text from files that were initially
contributed by Atheros Communications or Qualcomm Atheros.
Signed-hostap: Jouni Malinen <j@w1.fi>
Remove the GPL notification text from EAP-pwd implementation per
approval from Dan Harkins who contributed these files.
(email from Dan Harkins <dharkins@lounge.org> dated
Wed, 4 Jan 2012 16:25:48 -0800)
Signed-hostap: Jouni Malinen <j@w1.fi>
In case of !defined(IEEE8021X_EAPOL) the definition of the stub
pmksa_cache_get() in rsn_supp/pmksa_cache.h is not correct. This patch
adds the missing argument to the function definition to fix a
regression from commit 96efeeb66b.
Signed-hostap: Antonio Quartulli <ordex@autistici.org>
Search (p2p_scan) could already have been started at the point
remain-on-channel end event is being processed, e.g., if an Action frame
TX is reported immediately aftet the end of an earlier remain-on-channel
operation and the response frame is sent using an offchannel operation
while p2p_find is still in progress. Avoid trying to re-run p2p_scan
while the previous one is still running.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Commit 39185dfa54 changed the p2p_scan()
callback to return 1 in some cases, but forgot to change this p2p_scan()
call to handle that properly. Fix this by processing any non-zero value
as an error. This regression could leave the P2P module in state where
it believed a P2P scan was still running and refused to start some
operations until that scan gets completed (which would never happen
since it was not really started).
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Previously, PINs that are added with a wildcard UUID were allowed to
be used only by a single Enrollee. However, there may be more than one
Enrollee trying to connect when an AP indicates that active Registrar
is present. As a minimal workaround, allow two Enrollees to try to use
the wildcard PIN. More complete extension could use timeout and allow
larger set of Enrollees to try to connect (while still keeping in mind
PIN disabling requirement after 10 failed attempts).
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
"BSS p2p_dev_addr=<P2P Device Address>" can now be used to fetch a
specific BSS entry based on the P2P Device Address of the GO to avoid
having to iterate through the full BSS table when an external program
needs to figure out whether a specific peer is currently operating as
a GO.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
When the GO negotiation peer is assigned, the state also cannot be IDLE,
SEARCH, or LISTEN_ONLY.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When looking for PMKSA cache entries to use with a new association, only
accept entries created with the same network block that was used to
create the cache entry.
Signed-hostap: Jouni Malinen <j@w1.fi>
This fixes a corner case where a STA that has PMKSA cache entry (or
valid FT keys) could try to use full EAPOL/EAP authentication and fail.
If the STA will then try to use the still valid PMKSA cache entry (or
FT) before the STA entry has been cleared, authFail could have been left
to TRUE. That will make EAPOL authenticator PAE state machine enter HELD
state even though authSuccess was already forced to TRUE. This results
in the STA getting disconnected even though it should be allowed to
continue with 4-way handshake. While this is unlikely to happen in
practice, it is better to get this fixed by clearing authFail when
setting authSuccess.
Signed-hostap: Jouni Malinen <j@w1.fi>
intended-for: hostap-1
The TX status event may be received after a stations has been
disassociated in cases where the disassociation is following a
transmission of a Data frame. Ignore such events if the STA is not
associated at the moment the event is being processed. This avoids
confusing debug entries and rescheduling of the EAPOL TX timeouts for
STAs that are still in the STA table, but are not really in active EAPOL
session.
Signed-hostap: Jouni Malinen <j@w1.fi>
intended-for: hostap-1
While the exponential increase in the lockout period provides an
efficient mitigation mechanism against brute force attacks, this
additional trigger to enter indefinite lockout period (cleared by
restarting hostapd) will limit attacks even further by giving maximum of
10 attempts (without authorized user action) even in a very long term
attack.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This allows HT capabilities overrides on kernels that
support these features.
MCS Rates can be disabled to force to slower speeds when using HT.
Rates cannot be forced higher.
HT can be disabled, forcing an 802.11a/b/g/n station to act like
an 802.11a/b/g station.
HT40 can be disabled.
MAX A-MSDU can be disabled.
A-MPDU Factor and A-MPDU Density can be modified.
Please note that these are suggestions to the kernel. Only mac80211
drivers will work at all. The A-MPDU Factor can only be decreased and
the A-MPDU Density can only be increased currently.
Signed-hostap: Ben Greear <greearb@candelatech.com>
When there is not enough entropy and there are two station associating
at the same time, one of the stations will be rejected, but during
that rejection, the "reject_4way_hs_for_entropy" flag gets cleared. This
may allow the second station to avoid rejection and complete a 4-Way
Handshake with a GTK that will be cleared as soon as more entropy is
available and another station connects.
This reworks the logic to ban all 4-way handshakes until enough entropy
is available.
Signed-hostap: Nicolas Cavallari <cavallar@lri.fr>
In multiple BSSes scenario for the drivers that do not use
monitor interface and do not implement AP SME, RX MGMT
frame subscription happens only for the default bss (first_bss).
Subscribe for RX MGMT frames for such BSSes.
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Commit e4fb216769 moved frequency
storage from driver struct to bss struct and is assigned in
wpa_driver_nl80211_set_freq. As this wpa_driver_nl80211_set_freq is
triggered only on the first_bss, bss->freq for other BSSes is never
being set to the correct value. This sends MLME frames on frequency zero
(initialized value of freq) for BSSes other than the first.
To fix this derive frequency value from first_bss.
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
This patch allows to log hexdumps into syslog.
This is useful when testing, as syslog's network logging
helps to collect debug outputs from several machines.
Signed-hostapd: Nicolas Cavallari <cavallar@lri.fr>
The pseudonym identity should use a realm in environments where a realm is
used. Thus, the realm of the permanent identity is added to the pseudonym
username sent by the server.
Signed-hostap: Simon Baatz <gmbnomis@gmail.com>
The pseudonym identity should use a realm in environments where a realm is
used. Thus, the realm of the permanent identity is added to the pseudonym
username sent by the server.
Signed-hostap: Simon Baatz <gmbnomis@gmail.com>
When the "bssid=" option is set for an IBSS network and ap_scan = 2,
ask the driver to fix this BSSID, if possible.
Previously, any "bssid=" option were ignored in IBSS mode when ap_scan=2.
Signed-hostap: Nicolas Cavallari <cavallar@lri.fr>
It looks like Windows 7 WPS implementation does not like multiple
Authentication/Encryption Type bits to be set in M7 AP Settings
attributes, i.e., it refused to add a network profile if the AP
was configured for WPA/WPA2 mixed mode and AP PIN was used to
enroll the network.
Leave only a single bit set in the Authentication/Encryption Type
attributes in M7 when the AP is acting as an Enrollee to avoid this
issue.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
A P2P Action frame may need to be sent on another channel than the GO's
operating channel. This information was lost in
wpa_driver_nl80211_send_action() in the case the interface was in AP
mode. Pass the frequence and related parameters to send_mlme mechanism
to allow the correct frequence to be used with the send frame command in
AP (P2P GO) mode.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Number of places in hostapd use ap_sta_disconnect() instead of
ap_sta_disassociate() or ap_sta_deauthenticate(). There are some
differences between these functions, e.g., in the area how quickly
the EAPOL state machines get deinitialized. This can result in
somewhat unexpected events since the EAPOL/WPA authenticator
state machines could remain running after deauthentication.
Address this by forcing EAPOL/WPA authenticator state machines
to disabled state whenever ap_sta_disconnect() is called instead
of waiting for the deauthentication callback or other timeout
to clear the STA.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Even though we may not update P2P peer entry while connected to the
peer as a P2P client, we should not be expiring a P2P peer entry while
that peer is the GO in a group where we are connected as a P2P client.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Even though we may not receive a Probe Response from the peer during
the connection, we should not be expiring a P2P peer entry while that
peer is connected to a group where we are the GO.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The cookie value needs to be fetched in GO mode, too, to be able to
indicate TX status callbacks with drivers that handle AP mode SME
functionality internally. This fixes issues with client discoverability
where TX status callback for GO Discoverability Request is needed to
trigger the GO to send Device Discoverability Response.
Some SIM cards do not include MNC length with in EF_AD. Try to figure
out the MNC length based on the MCC/MNC values in the beginning of the
IMSI. This covers a prepaid Elisa/Kolumbus card that would have ended
up using incorrect MNC length based on the 3-digit default.
Signed-hostap: Jouni Malinen <j@w1.fi>
The temporary IMSI buffer can be used for this without needing the
extra memory allocation. In addition, the implementation is easier
to understand when the extra identity prefix value for EAP-SIM/AKA
is not included while fetching MCC/MNC from the IMSI.
Signed-hostap: Jouni Malinen <j@w1.fi>
The EF-AD (administrative data) file may contain information about the
length of the MNC (2 or 3 digits) in the IMSI. This can be used to
construct the realm according to 3GPP TS 23.003 during EAP-SIM or
EAP-AKA authentication.
Signed-hostap: Simon Baatz <gmbnomis@gmail.com>
This patch notifies the upper framework that an on-going discovery has
been stopped. This is useful in cases where a p2p_find with a timeout
value initiated by the upper framework has been finished or when the
framework initiated "p2p_find" is stopped by a "p2p_connect".
Signed-hostap: Jithu Jance <jithu@broadcom.com>
Some deployed station implementations seem to send msg 4/4 with
incorrect type value in WPA2 mode. Add a workaround to ignore that issue
so that such stations can interoperate with hostapd authenticator. The
validation checks were added in commit
f8e96eb6fd.
Signed-hostap: Jouni Malinen <j@w1.fi>
The Device ID attribute was already used in Listen state, but it was
ignored in GO role. Verify that there is a match with Device ID in
GO rule, too, before replying to the Probe Request frame.
Signed-hostap: Jouni Malinen <j@w1.fi>
dev_id=<P2P Device Addr> can now be specified as an argument to
p2p_find to request P2P find for a specific P2P device.
Signed-hostap: Jouni Malinen <j@w1.fi>
Some supplicant implementations (e.g., Windows XP WZC) update SNonce for
each EAPOL-Key 2/4. This breaks the workaround on accepting any of the
pending requests, so allow the SNonce to be updated even if we have
already sent out EAPOL-Key 3/4.
While the issue was made less likely to occur when the retransmit
timeout for the initial EAPOL-Key msg 1/4 was increased to 1000 ms,
this fixes the problem even if that timeout is not long enough.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Now that we can use driver_nl80211.c with non-mac80211 drivers that
implement SME/MLME internally, we may not get inactivity time from the
driver. If that is the case, we need to skip disconnection based on
maximum inactivity timeout. This fixes some unexpected disconnection
cases with ath6kl in AP mode.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The deauthentication and disassociation events from nl80211 were being
processed identically regardless of whether the frame was generated by
the local STA or the AP. This resulted in fast reconnection mechanism
getting triggered even in the case where the disconnection was detected
locally (e.g., due to beacon loss) while this was supposed to happen
only in the case where the AP is sending an explicit Deauthentication
or Disassociation frame with a specific reason code.
Fix this by adding a new deauth/disassoc event variable to indicate
whether the event was generated locally.
Signed-hostap: Jouni Malinen <j@w1.fi>
IEEE Std 802.1X-2004 does not clear authWhile and heldWhile in this
case, but doing so allows the timer tick to be stopped more quickly when
the port is not enabled. Since these variables are used only within HELD
and RECEIVE states, clearing them on initialization does not change
actual state machine behavior. This reduces some unnecessary operations
in port disabled state and cleans up the wpa_supplicant debug log after
disconnection.
Signed-hostap: Jouni Malinen <j@w1.fi>
Since wps_registrar_pbc_timeout is called to stop PBC, previously
registered wps_registrar_pbc_timeout must be canceled when canceling
the WPS operation.
Signed-off-by: Spencer Chang <jungwalk@gmail.com>
The offchanok parameter is hardcoded to one in number of paths and that
added NL80211_ATTR_OFFCHANNEL_TX_OK attribute to NL80211_CMD_FRAME
unconditional. cfg80211 rejects this with EINVAL if the driver does not
indicate support for offchannel TX. Fix this by not requesting
offchannel TX depending on driver capabilities. Remain-on-channel
operation was used for those cases anyway, so the additional attribute
was not really needed for these in the first place.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
When nl80211_setup_ap() has enabled Probe Request reporting, this must
not be disabled when P2P Listen state is stopped to avoid breaking AP
mode operations. This could happen, e.g., if a Probe Request frame was
received from a P2P device that the we are trying to invite to our group
(i.e., when operating in GO role). p2p_probe_req_rx() calls
p2p_invite_start() in this case and that ends up calling
p2p->cfg->stop_listen() which calls probe_req_report() driver op.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
hostapd uses the poll method to check if the station is alive
after the station has been inactive for ap_max_inactivity seconds.
Make the poll mechanism configurable so that user can choose to
disconnect idle clients.
This can be especially useful when some devices/firmwares have
restrictions on the number of clients that can connect to the AP
and that limit is smaller than the total number of stations trying
to use the AP.
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
The 100 ms timeout on retransmitting group key message can be too short
for stations that are in power save mode or if there is a large number
of association stations. While the retransmission of the EAPOL-Key frame
should allow this to be recovered from, it is useful to avoid
unnecessary frames to save soem CPU and power.
Signed-hostap: Jouni Malinen <j@w1.fi>
Drivers that use device SME in AP mode may still need to be
subscribed for Action frame RX when monitor interface is not used.
This fixes number of P2P GO operations with ath6kl.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Poll command may be enough for mac80211 to figure out whether monitor
interface is to be used, but this change did not take into account
non-mac80211 drivers that support AP mode without monitor interface.
For example, ath6kl needs to get use_monitor disabled.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Add a new persistent group network block field, p2p_client_list, to
maintain a list of P2P Clients that have connected to a persistent
group. This allows GO of a persistent group to figure out more easily
whether re-invocation of a persistent group can be used with a specific
peer device.
Signed-hostap: Jouni Malinen <j@w1.fi>
The P2P module provides access to public peer data in struct
p2p_peer_info. Use this to build the P2P_PEER information in
ctrl_iface.c instead of providing such text format data from the P2P
module.
The internal data that was previously built in p2p_get_peer_info() as
part of the text format peer data is now available through a separate
p2p_get_peer_info_txt() function. This is still included in P2P_PEER
output to maintain backwards compatibility with external programs that
could have started to use this. However, it should be noted that this
data is not really supposed to be used for anything else apart from
debugging purposes and its format is subject to change.
Signed-hostap: Jouni Malinen <j@w1.fi>
p2p_get_peer_info() was used in multiple places just to check whether a
specific peer is known. This was not the designed use for the function,
so introduce a simpler function for that purpose to make it obvious that
the p2p_get_peer_info() function is actually used only in ctrl_iface.c.
Signed-hostap: Jouni Malinen <j@w1.fi>
If p2p_listen is issued during a p2p_scan, a pending after-scan operation
is scheduled. However, since there is support for only a single pending
operation, this was able to override a previously scheduled pending
connect command. This can break some command sequences, so give higher
priority to pending connect operation.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Android ICS system/core/libnl_2 has very limited genl_ctrl_resolve()
implementation that cannot handle names other than nlctrl. Work
around that by implementing more complete genl_ctrl_resolve()
functionality within driver_nl80211.c for Android builds.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This event can be very frequent in AP mode when Beacon frames from
neighboring BSSes are delivered to user space. Drop the debug
message priority from DEBUG to EXCESSIVE for Beacon frames.
Signed-hostap: Jouni Malinen <j@w1.fi>
I needed this patch to compile against the latest
libnl code. I added this to my config file:
CONFIG_LIBNL32=y
Signed-hostap: Ben Greear <greearb@candelatech.com>
When waiting for go_neg frame from the peer in WAIT_PEER_CONNECT state,
I have observed that sometimes it takes 20 to 30 secs for successful GO
negotiation. I also found out that it is because of 1 second idle time,
in WAIT_PEER_CONNECT state. While it is good to have 1 second idle time
[for doing power-save or doing some other legacy STA Scan or some other
useful stuff], this makes GO Negotiation process slow.
We wait for 1 second idle and then listen for a random time between
100(min)-300(max) ms. Assume P1 is in WAIT_PEER_CONNECT state and P2 is
the one which is now to send go_neg frame. If P2 sends GO Negotiation
frame just at the boundary of 300 ms of P1 and assume that P2 takes
close to 600-800 ms for one iteration of sending go_neg request (one
iteration is GO Negotiation Request frame time + dwell time +
listen_time), P2 needs to transmit at least 16-18 Action frames for
hitting the listen time of P1.
Following patch reduces the idle time to 500 ms. Alternatively we can
increase the listen time interval to 500 ms just for WAIT_PEER_CONNECT
state.
Provision discovery from a known peer should actually check for
dev->flags & P2P_DEV_PROBE_REQ_ONLY. This is creating an issue of
updating the listen frequency of peer with the PD request frame
frequency. PD request frame will be sent by the peer on our local listen
frequency. This patch fixes that error. Suggested check has already been
implemented in the invitation req receive path.
The Provision Discovery Request needs to be sent on the operating
channel of the GO and as such, the frequency from the BSS table
(scan results) need to override the frequency in the P2P peer
table that could be based on the Listen channel of the GO.
Signed-hostap: Jouni Malinen <j@w1.fi>
The GO negotiation response is very cryptic at the moment. For a success
message we only know on which interface the negotiation succeeded, not
which peer. For a failure we know the interface also and a status code
(number).
It will be very useful for clients to know upon receipt of such a message
which peer the negotiation occurred with.
Now that the peer information is available and the API is changed
already, the function composing the D-Bus message might as well include
all GO negotiation information. This is done with a dict to make things
easier on clients if this result information changes down the line.
Signed-hostap: Reinette Chatre <reinette.chatre@intel.com>
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
When the station is connected to P2P GO after calling p2p_find command
the device sees itself. It is related to lack of filtering itself from
clients connected to P2P GO.
Step by step:
1. dev1: p2p_group_add
2. dev2: p2p_connect <MAC1> pbc join
3. dev1: wps_pbc
4. dev2: p2p_find
Skip P2P client information for our own device from a GO with which
we are connected.
It looks like some USIM cards respond with 0x67 (Wrong length) instead
of 0x6c to 00 b2 01 04 ff. This was getting rejected in
scard_get_record_len(). ETSI TS 102 221 is not very clear on this
detail, but it looks fine to accept the 0x67 error value, too, to learn
the record length.
Signed-hostap: Jouni Malinen <j@w1.fi>
Return 1/0 instead 0/-1 to indicate valid/invalid element so that
the if statement makes more sense with !wmm_valid().
Signed-hostap: Jouni Malinen <j@w1.fi>
This updates a previous patch did more or less the same thing by
providing the qosinfo as a single variable to the driver wrappers.
Signed-hostap: Jason Young <jason.young@dspg.com>
Add uapsd_queues and max_sp fields to sta_info struct,
and pass them to the sta_add callback.
These values are determined by the WMM IE in the (Re)Association Request.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Check whether the driver advertises support for U-APSD
in AP mode, and evaluate wmm_uapsd only in this case.
Signed-off-by: Eliad Peller <eliad@wizery.com>
The wpa_hexdump_ascii() call did not get converted properly and this
was missed becaused of it getting defined out from the build. Anyway,
this better use the correct variable names should that debug print
ever be enabled for Android.
Signed-hostap: Jouni Malinen <j@w1.fi>
A Pending Provision Discovery Request was sent in SEARCH phase after a
previous provision discovery timeout. Fix this by resetting the config
method of P2P device in the pending PD reset function. This avoids the
sending of a pending Provision Discovery Request during the next P2P
search.
Signed-off-by: Jean-Michel.Bachot <jean-michelx.bachot@intel.com>
Some debug messages used incorrect name for Provision Discovery.
Replace "Provisioning Discovery" with "Provision Discovery".
Signed-hostap: Jouni Malinen <j@w1.fi>
It is safer to assume that the driver could be using NoA and reject
any Presence Request unless we are sure that noa NoA is in use.
Signed-hostap: Jouni Malinen <j@w1.fi>
This allows per-device PSK to be configured for WPA-Personal using a
RADIUS authentication server. This uses RADIUS-based MAC address ACL
(macaddr_acl=2), i.e., Access-Request uses the MAC address of the
station as the User-Name and User-Password. The WPA passphrase is
returned in Tunnel-Password attribute in Access-Accept. This
functionality can be enabled with the new hostapd.conf parameter,
wpa_psk_radius.
Signed-hostap: Michael Braun <michael-dev@fami-braun.de>
WPS overlap detection can detect false overlap if a P2P peer
changes UUID while authentication is ongoing. Changing UUID
is of course wrong but this is what some popular devices do
so we need to work around it in order to keep compatibility
with these devices. There already is a mechanism in WPS
registrar to skip overlap detection if P2P addresses of two
sessions match but it wasn't really triggered because the
address wasn't filled in in the caller function.
Let's fill in this address and also clean up WPS PBC sessions
on WSC process completion if UUID was changed.
Signed-hostap: Vitaly Wool<vitalywool@gmail.com>
Pass the raw Probe Response template to kernel via netlink using the
set_ap() driver callback. The data is sent as one of the Beacon
attributes.
Signed-hostap: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Configure a Probe Response template for drivers that support it. The
template is updated when the Beacon template is updated.
The Probe Response template is propagated to the driver via the set_ap()
callback.
Signed-hostap: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
This is needed for Probe Response template, so move the code into a
separate function that can be shared.
Signed-hostap: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Translate nl80211 flags to wpa_supplicant flags for Probe Response
offload support. The existence of the nl80211 PROBE_RESP_OFFLOAD_SUPPORT
attribute means Probe Response offload is supported. The value of the
attribute is a bitmap of supported protocols.
Signed-hostap: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
This previously helped when debugging some auth issues when hitting the
AP with 128 association attempts all at once.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Append "p2p_dev_addr" parameter to AP-STA-DISCONNECTED event for P2P
connections. In addition, for AP-STA-CONNECTED event during P2P
connection, the "dev_addr=" print is replaced with "p2p_dev_addr=" to
be more consistent with other events.
Signed-hostap: Jithu Jance <jithu@broadcom.com>
Storing the address in the BSS instead of the DRV struct makes it usable
for hostapd and thus gets rid of the linux_get_ifhwaddr() call when
receiving a spurious frame.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
Testing code can now be enabled in the hostapd RADIUS server to dump
each derived MSK into a text file (e.g., to be used as an input to
wlantest). This functionality is not included in the default build
and can be enabled by adding the following line to hostapd/.config:
CFLAGS += -DCONFIG_RADIUS_TEST
The MSK dump file is specified with dump_msk_file parameter in
hostapd.conf (path to the dump file). If this variable is not set,
MSK dump mechanism is not enabled at run time.
Signed-hostap: Jouni Malinen <j@w1.fi>
If Provision Discovery Request is sent for GO role (i.e., P2P Group ID
attribute is included), add the group interface name to the control
interface event on the GO. This makes it easier to figure out which
ctrl_iface needs to be used for wps_pbc/wps_pin command to authorize
the joining P2P client.
Signed-hostap: Jouni Malinen <j@w1.fi>
If p2p_prov_disc join command is used prior to p2p_connect join,
skip the duplicated provision discovery exchange.
Signed-hostap: Jithu Jance <jithu@broadcom.com>
This can be used to request Provision Discovery Request to be sent
for the purpose of joining a running group, e.g., to request the GO
to display a PIN that we can then use with p2p_connect join command.
Signed-hostap: Jithu Jance <jithu@broadcom.com>
Since the nl_cache is not used anymore, there is no need for maintaining
the struct nl80211_handles wrapper for struct nl_handle. Clean this up
by using nl_handle directly.
Signed-hostap: Jouni Malinen <j@w1.fi>
This is a rewrite of Ben Greear's patch, making the
nl80211 code use just a single multicast event socket.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
When running AP mode, we need to receive beacons over overlapping BSSes
to handle protection. Use the new nl80211 command for this. As the
command works per wiphy (and we don't want to receive the Beacon frames
multiple times) add an abstraction that keeps track of per-wiphy data.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
These events are necessary to send deauth frames to
stations sending spurious data frames. Subscribe to
them on the per-BSS event socket.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
To achieve this, multiple things are needed:
1) since hostapd needs to handle *all* action frames,
make the normal registration only when in a non-AP
mode, to be able to do this use the new socket
2) store the frequency in each BSS to be able to give
the right frequency to nl80211's mgmt-tx operation
3) make TX status processing reject non-matched cookie
only in non-AP mode
The whole thing depends on having station-poll support
in the kernel. That's currently a good indicator since
the kernel patches are added together.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
Fix start of reauthentication after failed authentication with
passthrough (external AAA server) to use internal EAP Identity method.
Signed-hostap: Jouni Malinen <j@w1.fi>
This reverts commit 204dd3f420.
start_reauth was not supposed to be used in this way and setting it
to TRUE in INITIALIZE breaks internal EAP server.
Signed-hostap: Jouni Malinen <j@w1.fi>
When using authentication retry within driver_nl80211.c, a failure on the
second attempt has to be indicated with a driver event since the return
code from wpa_driver_nl80211_authenticate() is not actually delivered to
the core code in that case.
Signed-hostap: Jouni Malinen <j@w1.fi>
cfg80211 rejects NL80211_CMD_AUTHENTICATE with ENOENT if the BSS entry
for the target BSS is not available. This can happen if the cfg80211
entry has expired before wpa_supplicant entry (e.g., during a suspend).
To recover from this quickly, run a single channel scan to get the
cfg80211 entry back and then retry authentication command again. This
is handled within driver_nl80211.c to keep the core wpa_supplicant
implementation cleaner.
Signed-hostap: Jouni Malinen <j@w1.fi>
The pseudonym is a temporary identity, but is no one-time identifier (like
the fast re-authentication identity). Thus, do not forget it if the server
does not include it in every challenge. There are servers that include the
pseudonym identity only at full-auth. [Bug 424]
Make sure sign extension does not end up getting used here by
explicitly type casting the variables to correct size.
Signed-hostap: Jouni Malinen <j@w1.fi>
Commit 34445d12ee forgot to convert
the hostapd_prepare_rates() inline wrapper for builds that do not
define NEED_AP_MLME.
Signed-hostap: Jouni Malinen <j@w1.fi>
P2P invitation responses are transmitted with the BSSID set to the peer
address. Pass these action frames up to allow the GO to receive the
Invitation Response (and avoid sending the Invitation Request multiple
times).
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Set the NL80211_ATTR_CONTROL_PORT_NO_ENCRYPT flag for nl80211 to tell
drivers (mac80211) to not encrypt the EAPOL frames for WEP IEEE 802.1X.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
In preparation for things that receive on a BSS-specific handle,
allocate a CB for it and hook it up to receive functions.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
The next patch will add process_bss_event, rename process_event to
process_drv_event to differentiate between them.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
By passing the nl_cb as the context to the eloop function we can
(in the next patch) use the same eloop function for BSS events.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
Storing the frequency in the bss struct allows using it for frame
commands in AP mode and not relying on the driver struct as much, which
is good for hostapd mode.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
This will allow getting TX status for EAPOL frames
sent as data frames if the driver supports it.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
Previously, sm->start_reauth was set to TRUE in SUCCESS2 state to force
reauthentication to start with EAP identity request. This works fine for
the case of EAP success through the AAA passthrough authentication, but
is not enough to handle passthrough authentication failure. sm->identity
is set in that case and getDecision would return PASSTHROUGH instead of
CONTINUE (to Identity method).
Signed-hostap: Jouni Malinen <j@w1.fi>
The RTM_NEWLINK even can have IFF_UP flag even if the interface is
down. Do not generate EVENT_INTERFACE_ENABLED event based on such a
message.
Signed-hostap: Jouni Malinen <j@w1.fi>
A new hostapd.conf parameter, wps_rf_bands, can now be used to fix the
RF Bands value in cases where hw_mode is not set or when operating a
dual band dual concurrent AP.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
When hostapd controls multiple radios, WPS operations are started on
all interfaces. However, when the provisioning run had been completed
successfully, actiove WPS mode was stopped only a single interface. Fix
this to iterate through all interfaces so that this is handled
consistently with the starting of WPS operation.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Commit 628d54639a introduced number
of new WPS related ctrl_iface messages to hostapd. Some of these
were for ER events which do not make any sense to hostapd that
cannot operate as an ER. The WPS_EV_ER_SET_SELECTED_REGISTRAR one
from wps_registrar_sel_registrar_changed_event() was especially
problematic since it can cause wpa_supplicant ER code segfault due
to missing event data.
Revert all the ER specific changes from commit
628d54639a to get rid of the segfault
and undesired extra code in hostapd.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This is based on the Android driver_cmd changes that are converted to
use the sched_scan/stop_sched_scan driver_ops for the case where the
driver does not support the new nl80211 commands.
Change-Id: Iaedc340f84650af422bd2ea57d2a8b0a9d4a5330
Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
(jm: This is based on the Android change that used driver_cmd. The same
implementation is used for the actual driver interface, but the commands
are now accessed through sched_scan/stop_sched_scan driver_ops instead
of driver_cmd)
While the copy is not used as a null terminated string, this can prevent
some static analyzers from complaining about non-issue.
Signed-hostap: Jouni Malinen <j@w1.fi>
Add support for generating and verifying RFC 3447 RSASSA-PKCS1-v1_5
style DigestInfo for TLS v1.2 CertificateVerify. For now, this is
hardcoded to only support SHA256-based digest.
Signed-hostap: Jouni Malinen <j@w1.fi>
This allows the internal TLS implementation to be built for TLS v1.2
support. In addition to the build option, this changes the TLS PRF
based on the negotiated version number. Though, this commit does not
yet complete support for TLS v1.2.
Signed-hostap: Jouni Malinen <j@w1.fi>
Prepare for multiple TLS PRF functions by renaming the SHA1+MD5 based
TLS PRF function to more specific name and add tls_prf() within the
internal TLS implementation as a wrapper for this for now.
Signed-hostap: Jouni Malinen <j@w1.fi>
IW_ENCODE_ALG_PMK and IW_ENC_CAPA_4WAY_HANDSHAKE are not defined in the
Android tree, so add compatibility defines for these.
Signed-hostap: Jouni Malinen <j@w1.fi>
Send the connection events from P2P group to both the group interface
and parent interface ctrl_ifaces to make it easier for external monitor
programs to see these events without having to listen to all group
interfaces when virtual group interfaces are used.
Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
cfg80211 will reject the NL80211_CMD_START_SCHED_SCAN if too many
match sets are requested. To avoid being completely unable to start
any scheduled scans, skip setting these filters if the driver did
not advertise support for large enough number of match sets.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This adds initial implementation of set_p2p_powersave to allow legacy PS
mode to be configured. P2P PS parameters are not yet supported.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This cleans up the source code and makes it less likely that new AKM
addition misses some needed changes in the future.
Signed-hostap: Jouni Malinen <j@w1.fi>
If the station is indicating use of WPS, WSC IE should be added into the
(Re)Association Response frame. This is clear for the case when WSC IE
was included in the (Re)Association Request frame. However, even the
WLAN_STA_MAYBE_WPS case may actually indicate use of WPS. Assume that to
be the case when WPA/WPA2 is enabled (i.e., when the STA does not
include WPA/RSN/WSC IE while AP has WPA/RSN enabled).
Signed-hostap: Jouni Malinen <j@w1.fi>
This makes it clearer that the PMKSA caching entry gets removed from
the driver regardless of how the internal entry from wpa_supplicant
gets cleared. In practice, this call was skipped only for the case
when the entry for the current AP was being updated, so the previous
version was likely to work with all drivers. Anyway, it is cleaner
to explicitly remove the old entry even in that case before the new
entry gets added.
Signed-hostap: Jouni Malinen <j@w1.fi>
Commit 940a0ce970 moved the STA associated
check from driver_*.c into ieee802_1x_receive(), but failed to take into
account that wired networks and driver_wired.c do not mark the STA entry
associated. Fix this by skipping the check if the driver wrapper is
using a wired network.
Signed-hostap: Jouni Malinen <j@w1.fi>
It's not really valid to send off-channel in all cases,
so pass whether it should be allowed or not and don't
set it in the AP case.
Also, to get the right ifindex for hostapd, pass a bss
pointer instead of the drv pointer.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
Some client implementations only wait a few ms after sending a probe
request while scanning. Since probe responses are always sent at a low
rate this can eat quite some airtime and it might be impossible to get
the frame out before the client leaves the channel again. If the client
leaves before all probe reponses where acked this can cause the probe
reponse to be retried quite often consuming even more airtime.
Hence, add a new noack flag to the driver's send_mlme callback that
allows hostapd to request whether the driver should expect an ACK for
this frame or not.
Use the new noack-policy only for broadcast probe requests that contain
a wildcard SSID.
Signed-hostap: Helmut Schaa <helmut.schaa@googlemail.com>
In some situations it might be benefical to send a unicast frame without
the need for getting it ACKed (probe responses for example). In order to
achieve this add a new noack parameter to the drivers send_mlme callback
that can be used to advise the driver to not wait for an ACK for this
frame.
Signed-hostap: Helmut Schaa <helmut.schaa@googlemail.com>
This structure was not really used for anything apart from figuring out
length of the EAP-pwd header (and even that in a way that would not work
with fragmentation). Since the bitfields in the structure could have
been problematic depending on target endianness, remove this unnecessary
structure.
Signed-hostap: Jouni Malinen <j@w1.fi>
Another niceness of OpenSSL is that if the high-order bit of a 521-bit
big num is not set then BN_bn2bin() will just return 65 bytes instead of
66 bytes with the 1st (big endian, after all) being all zero. When this
happens the wrong number of octets are mixed into function H(). So
there's a whole bunch of "offset" computations and BN_bn2bin() dumps the
big number into a buffer + offset. That should be obvious in the patch
too.
The previous EAP-pwd KDF implemented has an issue with group 21, that is
an elliptic curve group based on a 521 bit prime. 521 is not an even
multiple of 8, and therein lies the problem.
OpenSSL's BN library interprets a string of bits as in big-endian format
so all the calls of BN_bin2bn() will take the binary blob of bits and
turn it into a big number in big-endian format. In the EAP-pwd KDF, I am
stretching the key to "primebitlen". When that is not an even multiple
of 8 I have to mask off the excess. But I was masking off the excess
bits in the 1st octet (big endian after all) but that isn't right. The
KDF produces a string of endian-less bits. The 521st bit is the first
bit in the last octet, not the 7th bit in the first octet. So that has
been fixed and you can see in the attached diff what I'm doing.
If the kernel supports this, don't use manual null
data frame transmissions. This is one thing to get
rid of cooked monitor interfaces.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
The non-monitor TX currently uses a normal L2 abstraction
socket, but that will also receive frames we don't want,
so use a plain socket that isn't bound for RX. This might
be possible using the L2 abstraction, but we need a plain
socket later for getting TX status events here.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
This changes the auto-detection of whether or not the device contains
the AP SME away from monitor interface addition failing to the explicit
attribute in nl80211. Keep the old auto-detection for a little while so
that ath6kl isn't broken right away.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
The new event can be used when EAPOL TX status can't be reported as a
complete 802.11 frame but is instead reported as just the EAPOL data as
originally passed to hapd_send_eapol().
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
Currently OpenSSL implementation of TLS in hostapd loads only top
certificate in server certificate file. Change this to try to the
whole chain first and only if that fails, revert to old behavior.
Signed-off-by: Maciej Szmigiero <mhej@o2.pl>
This patch implements shared_freq handler for driver_nl80211.c. If a
"p2p_group_add" happens after legacy STA association, then this patch
will help to start the GO on the same frequency. This is useful when
supplicant is started on multiple interface running over a singly "PHY"
and the station interface is not used for the P2P device operations.
For example, wpa_supplicant -iwlan0 .. -N -iwlan1 ... and wlan0 is used
for station connection and wlan1 as the P2P device interface.
Signed-hostap: Jithu Jance <jithu@broadcom.com>
Without this, it is impossible to tell exactly which
MLME code returned the error.
Also, convert to wpa_dbg so that we get device names
in the messages.
Signed-hostap: Ben Greear <greearb@candelatech.com>
When GO negotation fails the WPS method is currently not cleared, which
can result in GO negotiation being resumed when a GO negotiation request
frame is received from the peer. That is unexpected as locally we
already gave up.
This manifests itself in getting
1319574733.955685: wlan0: P2P-GO-NEG-FAILURE status=-1
1319574733.955723: P2P: Removing pending group interface p2p-wlan0-0
...
1319574736.648378: wlan0: P2P: Starting GO Negotiation with previously
authorized peer
...
1319574736.650115: wlan0: P2P: Sending GO Negotiation Response
...
1319574736.988038: wlan0: P2P-GO-NEG-SUCCESS
1319574736.988233: P2P: No pending group interface
1319574736.988268: P2P: Create a new interface p2p-wlan0-1 for the group
Clear the WPS method to avoid this situation. I wasn't
able to test this though, but given the log I can only
assume this is how the situation happened.
Reported-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
If P2P device expires while a GO Negotiation is in progress, currently
p2p->go_neg_peer is cleared without indicating GO Nego failure. This
will result in pending group interfaces to be left over. This patch will
indicate GO Negotiation failure and will remove any pending group
interfaces.
This patch addresses a corner case in GO-Negotiation case. Consider the
scenario where two devices A and B are in discovery stage and Device B
vanishes [moves out of range] when a connect is issued on the Device A.
Then Device A keeps on retrying the GO Negotiation Request till the
retry limit is reached. On reaching retry limit, the pending group
interface is removed. But suppose if the peer entry in the device list
expires before the retry limit is reached, then pending group interface
was not removed.
Signed-off-by: Jithu Jance <jithu@broadcom.com>
Invalid use of memcpy instead of memcmp in comparison resulted in the
GO interface address getting set incorrectly if the GO did not show up
in scan results anymore.
Signed-hostap: Jouni Malinen <j@w1.fi>
trace.h may end up including system header files that define offsetof,
so include the compatibility definition from list.h only after this.
Signed-hostap: Jouni Malinen <j@w1.fi>
HT_INFO_OPERATION_MODE_OP_MODE_MASK is used with variables in host
byte order, so it should not be claimed as le16.
Signed-hostap: Jouni Malinen <j@w1.fi>
This is a workaround for Windows 7 supplicant rejecting WPA msg 3/4
in case it used Secure=1 in msg 2/4. This can happen, e.g., when
rekeying PTK after EAPOL-Key Error Request (Michael MIC failure)
from the supplicant.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This cleans up the code a bit by not having to deal with theoretical
possibility of maximum number of EAP methods to be different between
various components in hostapd.
Signed-hostap: Jouni Malinen <j@w1.fi>
Some static analyzers complain about memset with '0' value. This was
used correctly here, but since use of strdup is about as good an option,
use that to silence the invalid warnings.
Signed-hostap: Jouni Malinen <j@w1.fi>
This avoid incorrect errors from some static analyzers that do not like
memmove with pointers just after the end of a buffer even if the number
of bytes to move is zero.
Signed-hostap: Jouni Malinen <j@w1.fi>
All we really need is the family ID, and we can
get that with genl_ctrl_resolve() and then don't
need to worry about family/cache objects.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
If a P2P client associates with the group while it is
already associated, two member entries may be added to
the group which also confuses num_members counting.
Deal with this by removing the existing entry first
before adding a new one.
I think the way Reinette ran into this was due to our
tx_sync implementation in iwlagn, mac80211 might have
queued two association frames thinking the first one
just failed, but both only went out after the sync was
really successful (which tx_sync doesn't wait for).
Reported-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
The P2P_FIND command was failing if it was issued at the moment when
a scan operation was in progress. Avoid returning failure in this
case by scheduling the P2P find to start once the ongoing scan is
completed.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
WEXT is not really changing anymore and more or less all Linux
distros come with linux/wireless.h that is recent enough to
allow the driver wrappers to be build.
Signed-hostap: Jouni Malinen <j@w1.fi>
Commit c2ff13c533 broke this with a
copy-paste typo that ended up adding the Probe Request P2P IE into the
Beacon frame (i.e., Beacon frame had two P2P IEs while Probe Response
had none).
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Avoid zero-length memset at the end of the buffer. This is not really
needed, but it makes the code a bit easier for static analyzers.
Signed-hostap: Jouni Malinen <j@w1.fi>
Avoid zero-length memset at the end of the buffer. This is not really
needed, but it makes the code a bit easier for static analyzers.
Signed-hostap: Jouni Malinen <j@w1.fi>
Explicitly validate data_len so that static analyzers do not get
confused about the padlen validation. This is not really needed, but it
makes the code a bit easier for static analyzers.
Signed-hostap: Jouni Malinen <j@w1.fi>
Explicitly validate seed_len to skip memset call with zero length
of copied data at the end of the buffer. This is not really needed,
but it makes the code a bit easier for static analyzers.
Signed-hostap: Jouni Malinen <j@w1.fi>
data->phase2_method cannot really be NULL if
eap_fast_init_phase2_method() returns success, but this construction
seems to be too difficult for some static analyzers. While this change
is not really needed in practice, it makes it easier to go through
warnings from such analyzers.
Signed-hostap: Jouni Malinen <j@w1.fi>
hapd->time_adv cannot really be NULL if hostapd_update_time_adv()
returns success, but this construction seems to be too difficult
for some static analyzers. While this change is not really needed
in practice, it makes it easier to go through warnings from such
analyzers.
Signed-hostap: Jouni Malinen <j@w1.fi>
md->curlen cannot indicate full buffer size here since the buffered
data is processed whenever the full block size of data is available.
Avoid invalid warnings from static analyzers on memcpy() outside the
buffer length by verifying that curlen is smaller than block size.
Signed-hostap: Jouni Malinen <j@w1.fi>
This function can fail in theory since the SHA-1 functions are
allowed to return an error. While this does not really happen in
practice (we would not get this far if SHA-1 does not work), it is
cleaner to include the error handling here to keep static analyzers
happier. [Bug 421]
Signed-hostap: Jouni Malinen <j@w1.fi>
This has been obsoleted by the more generic Linux WEXT (driver_wext.c)
support. The hostap and madwifi driver wrappers can now be used only
with hostapd. The old station interface remains available in releases up
to 1.x.
Signed-hostap: Jouni Malinen <j@w1.fi>
The driver wrappers broadcom, iphone, osx, and ralink have not been
maintained for a while and it does not look like they will be in the
future either. As such, remove them from the development branch. The
previous versions will be included in older releases up to 1.x.
Signed-hostap: Jouni Malinen <j@w1.fi>
Reassemble partial TLS records to make the internal TLS client
implementation more convenient for stream sockets.
Signed-hostap: Jouni Malinen <j@w1.fi>
The padding validation was done on the last padding-length octets in the
buffer which misses the first padding octet (the last octet is the
padding length). Fix the starting offset for the comparison loop to get
the first octet verified. [Bug 420]
Signed-hostap: Jouni Malinen <j@w1.fi>
Return number of user input bytes from tlsv1_record_receive() to
move this detail into the proper record layer processing. In addition,
ignore unknown content types at record layer and allow processing to
continue after warning level TLS alerts to provide minimal workaround
for closure alerts.
Signed-hostap: Jouni Malinen <j@w1.fi>
Instead of trying to remember to add wpa_msg() calls for every possible
path where a STA becomes authorized or unauthorized, use
ap_sta_set_authorized() to send these events more consistently.
Signed-hostap: Jouni Malinen <j@w1.fi>
wpa_msg() has to use hapd->msg_ctx instead of hapd as the context
pointer to work properly in wpa_supplicant AP mode.
Signed-hostap: Jouni Malinen <j@w1.fi>
Currently, there is no events over the control interface
when a AP disconnects a station due to inactivity. With
this patch, an "AP-STA-DISCONNECTED" event will be sent.
Signed-hostap: Nicolas Cavallari <nicolas.cavallari@lri.fr>
Use a driver_ndis.c specific initialization function to fill in the
wpa_driver_ops information to make it easier to modify struct
wpa_driver_ops in the future. Being able to build driver_ndis.c
with MSVC was the only reason for having to maintain the same order
of function pointers in struct wpa_driver_ops and for having to
update driver_ndis.c for all changes in that structure.
Signed-hostap: Jouni Malinen <j@w1.fi>
The GTK is renewed in the hostapd after a MIC attack dissassociation
without informing the driver, causing decryption failures. This patch
sends the new GTK/IGTK to the driver after it is updated by the hostapd.
Signed-off-by: Yoni Divinsky <yoni.divinsky@ti.com>
When the supplicant acts as a registrar to learn the access point
parameters send the credentials to the wpa_cli interface after
receiving the 7th message. This is needed for proper behavior with
wps_cred_processing set to 1 or 2.
Without this patch, after the 7th message you got the WPS-CRED-RECEIVED
notification without the credentials. This was because the cred_attr and
cred_attr_len were not filled in in the wps structure.
Signed-off-by: Olivier Sobrie <olivier@sobrie.be>
In scan.c, merge a channel's noise value into the scan results. When
comparing scan results, compute the signal-to-noise ratio and use it
when available. Prefer a 5 GHz network if its SNR is really big (> 30)
or if its SNR is relatively close to the other network's.
Some stations have been reported to send EAPOL-Key Error Reports
indicating Michael MIC failures even when the cipher is not TKIP
(e.g., when the network is using only CCMP). Ignore such reports
to avoid starting TKIP countermeasures unnecessarily. This can
prevent certaint types of denial of service attacks by insiders,
but mostly this is to work around invalid station implementations.
Signed-hostap: Jouni Malinen <j@w1.fi>
The eloop timeout to stop TKIP countermeasures has to be canceled
on deinit path to avoid leaving bogus timeouts behind.
Signed-hostap: Jouni Malinen <j@w1.fi>
Converts from a string to a control request enum when input
from a control interface is received. Will be used by a
subsequent patch.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Control requests will be extended for non-EAP uses later, so it makes
sense to have them be generic. Furthermore, having them defined as an
enum is easier for processing internally, and more generic for control
interfaces that may not use field names. The public ctrl_req_type /
field_name conversion function will be used later by the D-Bus control
interface too.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Special processing is needed to handle EAP user request for
identity or password at the beginning of Phase 2 when the implicit
identity request is used. data->pending_phase2_req needs to be set
to an empty buffer in that case to avoid re-processing the previous
part of TLS negotiation when the user enters the needed information.
Signed-hostap: Jouni Malinen <j@w1.fi>
