This new mechanism allows P2P Client to request an IPv4 address from the
GO as part of the 4-way handshake to avoid use of DHCP exchange after
4-way handshake. If the new mechanism is used, the assigned IP address
is shown in the P2P-GROUP-STARTED event on the client side with
following new parameters: ip_addr, ip_mask, go_ip_addr. The assigned IP
address is included in the AP-STA-CONNECTED event on the GO side as a
new ip_addr parameter. The IP address is valid for the duration of the
association.
The IP address pool for this new mechanism is configured as global
wpa_supplicant configuration file parameters ip_addr_go, ip_addr_mask,
ip_addr_star, ip_addr_end. For example:
ip_addr_go=192.168.42.1
ip_addr_mask=255.255.255.0
ip_addr_start=192.168.42.2
ip_addr_end=192.168.42.100
DHCP mechanism is expected to be enabled at the same time to support P2P
Devices that do not use the new mechanism. The easiest way of managing
the IP addresses is by splitting the IP address range into two parts and
assign a separate range for wpa_supplicant and DHCP server.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This introduces new AKM for SAE and FT-SAE and adds the initial parts
for going through the SAE Authentication frame exchange. The actual SAE
algorithm and new fields in Authentication frames are not yet included
in this commit and will be added separately. This version is able to
complete a dummy authentication with the correct authentication
algorithm and transaction values to allow cfg80211/mac80211 drivers to
be tested (all the missing parts can be handled with
hostapd/wpa_supplicant changes).
Signed-hostap: Jouni Malinen <j@w1.fi>
Try to share most of the cipher information like key and RSC lengths and
suite selector conversions, etc. in wpa_common.c to avoid having similar
code throughout the WPA implementation for handling cipher specific
behavior.
Signed-hostap: Jouni Malinen <j@w1.fi>
This allows both hostapd and wpa_supplicant to be used to derive and
configure keys for GCMP. This is quite similar to CCMP key
configuration, but a different cipher suite and somewhat different rules
are used in cipher selection. It should be noted that GCMP is not
included in default parameters at least for now, so explicit
pairwise/group configuration is needed to enable it. This may change in
the future to allow GCMP to be selected automatically in cases where
CCMP could have been used.
This commit does not included changes to WPS or P2P to allow GCMP to be
used.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This cleans up the source code and makes it less likely that new AKM
addition misses some needed changes in the future.
Signed-hostap: Jouni Malinen <j@w1.fi>
CFLAGS += -DCONFIG_RSN_TESTING in .config and rsn_testing=1 in
hostapd.conf can now be used to enable a testing mode that adds
extensions to RSN element. This can be used to check whether
station implementations are incompatible with future extensions
to the RSN element.
There is no point in maintaining two almost identical versions
of this parser. Move WPA IE parser into wpa_common.c similarly
to what was already the case with RSN IE parse.
The three existing enums were already depending on using the same
values in couple of places and it is just simpler to standardize on
one of these to avoid need for mapping between different enums for
the exact same thing.
Doxygen and some build tools may get a bit confused about same file
name being used in different directories. Clean this up a bit by
renaming some of the duplicated file names in src/ap.
This code can be shared by both hostapd and wpa_supplicant and this
is an initial step in getting the generic code moved to be under the
src directories. Couple of generic files still remain under the
hostapd directory due to direct dependencies to files there. Once the
dependencies have been removed, they will also be moved to the src/ap
directory to allow wpa_supplicant to be built without requiring anything
from the hostapd directory.
