Previously, eight character random passphrase was generated
automatically for P2P GO. The new p2p_passphrase_len parameter can be
used to increase this length to generate a stronger passphrase for cases
where practicality of manual configuration of legacy devices is not a
concern.
Signed-off-by: Jouni Malinen <j@w1.fi>
Performing a P2P Device flow such as p2p_listen or
p2p_find, can degrade the performance of an active interface
connection, if the listen frequency is different than the
frequency used by that interface.
To reduce the effect of P2P Device flows on other interfaces,
try changing the listen channel of the P2P Device to match the
operating channel of one of the other active interfaces. This change
will be possible only in case that the listen channel is not forced
externally, and will be delayed to a point where the P2P Device
state machine is idle.
The optimization can be configured in the configuration file and
is disabled by default.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
This makes the p2p_find default delay value configurable as
p2p_search_delay parameter through the configuration file (and through
control interface "SET p2p_search_delay <value>" on the P2P management
interface.
This parameter controls the number milliseconds of extra delay that is
added between search iterations when there is a concurrent operation in
progress. This can be used, e.g., p2p_search_delay=100 to make p2p_find
friendlier to concurrent operations by avoiding it from taking 100% of
the radio resources. The default value is the previous default, i.e.,
500 ms. Smaller values can be used to find peers more quickly at the
cost of larger effect to concurrent operations while a larger value
leaves more time for the concurrent operations at the cost of making
device discovery take longer time.
The optional p2p_find delay argument can still be used to override the
search delay for each search operation.
Since the P2P_CONCURRENT_SEARCH_DELAY macro is not used anymore, the
driver specific build parameter for bcmdhd from Android.mk is also
removed. Similar configuration can now be achieved with
p2p_search_delay=0 in the p2p0 interface configuration file.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add a new wowlan_triggers option to wpa_supplicant.conf. The triggers in
this key will be used to configure the kernel wowlan configuration.
For now, support only simple flags. More complex triggers can be added
later on.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
This allows the specific SIM to be identified for authentication
purposes in multi-SIM devices. This SIM number represents the index of
the SIM slot. This SIM number shall be used for the authentication using
the respective SIM for the Wi-Fi connection to the corresponding
network.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
"GET_CRED <id> <field>" can now be used to fetch credential parameters
over the control interface. This does not allow passwords etc. private
material to be retrieved ("*" is returned for those if the value is set
regardless of the value). FAIL is returned if the requested parameter
has not been set. For cred parameters that can have multiple values,
newline separated list of values is returned.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This new parameter can be used to configure credentials to mandate use
of OCSP stapling for AAA server authentication.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This new priority parameter can be used to specify priorities between
credentials provisioned by the same SP. cred->priority is checked first
and if it is same and the provisioning_sp parameter matches, the new
sp_priority is used to order the credentials. It should be noted that
the order of priorities is different (higher 'priority' value indicates
higher priority of the credential, while higher 'sp_priority' indicates
lower priority of the credential).
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The new credential parameter req_conn_capab can be used to specify
restrictions on roaming networks providing connectivity for a set of
protocols/ports.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The new credential parameter max_bss_load can be used to specify
restrictions on BSS Load in the home network.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The new credential parameters min_{dl,ul}_bandwidth_{home,roaming} can
be used to specify restrictions on available backhaul bandwidth.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The new provisioning_sp cred field can now be used to track which SP
provisioned the credential. This makes it easier to find the matching
PPS MO from the management tree (./Wi-Fi/<provisioning_sp>).
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The new wpa_cli fetch_osu command can be used to fetch information about
all OSU providers and write that to a text file with the icons in
separate files. cancel_osu_fetch command can be used to stop ongoing OSU
provider list fetch.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The HS 2.0 Indication element from wpa_supplicant now includes the
release number field and wpa_supplicant shows the release number of the
AP in STATUS command (hs20=1 replaced with hs20=<release>).
The new update_identifier field in the cred block can now be used to
configure the PPS MO ID so that wpa_supplicant adds it to the Indication
element in Association Request frames.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The new roaming_partner parameter within a cred block can be used to
configure priorities for roaming partners.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
1. In wpa_config_process_bgscan() fix memory leak after
calling wpa_config_parse_string()
2. In hostapd_config_defaults(), on failure to allocate bss->radius,
conf->bss was not freed.
3. In p2p_deauth_nofif(), memory allocated in p2p_parse_ies() was not
freed in case of NULL minor_reason_code.
4. In p2p_disassoc_nofif(), memory allocated in p2p_parse_ies() was
not freed in case of NULL minor_reason_code.
5. In p2p_process_go_neg_conf(), memory allocated was not freed in
case that the P2P Device interface was not waiting for a
GO Negotiation Confirm.
6. In wpa_set_pkcs11_engine_and_module_path(), the wrong pointer was
checked.
Signed-hostap: Eytan Lifshitz <eytan.lifshitz@intel.com>
This new mechanism allows P2P Client to request an IPv4 address from the
GO as part of the 4-way handshake to avoid use of DHCP exchange after
4-way handshake. If the new mechanism is used, the assigned IP address
is shown in the P2P-GROUP-STARTED event on the client side with
following new parameters: ip_addr, ip_mask, go_ip_addr. The assigned IP
address is included in the AP-STA-CONNECTED event on the GO side as a
new ip_addr parameter. The IP address is valid for the duration of the
association.
The IP address pool for this new mechanism is configured as global
wpa_supplicant configuration file parameters ip_addr_go, ip_addr_mask,
ip_addr_star, ip_addr_end. For example:
ip_addr_go=192.168.42.1
ip_addr_mask=255.255.255.0
ip_addr_start=192.168.42.2
ip_addr_end=192.168.42.100
DHCP mechanism is expected to be enabled at the same time to support P2P
Devices that do not use the new mechanism. The easiest way of managing
the IP addresses is by splitting the IP address range into two parts and
assign a separate range for wpa_supplicant and DHCP server.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
All te network blocks and credentials were already cleared, but
configurations blobs should also be cleared here, e.g., to get
more consistent behavior test cases using EAP-FAST PACs.
Signed-hostap: Jouni Malinen <j@w1.fi>
The new cred block parameter 'temporary' can be used to indicate that a
cred block is not to be saved to wpa_supplicant configuration file
(e.g., "SET_CRED 0 temporary 1"). This is similar to the concept of
temporary network blocks and allows cred blocks to be managed outside
the wpa_supplicant config file when other parameters are still saved to
the file written by wpa_supplicant.
Signed-hostap: Jouni Malinen <j@w1.fi>
There are use cases requesting the host driver to initiate the TDLS
setup with the peer only when configured by the external applications.
Thus, enable this control by tdls_external_control=1 and pass the
requisite information for the specific TDLS operation to the driver
on the request from such use cases.
This operation mode expects the driver to initiate TDLS link
automatically based on signal strength and traffic to a peer and tear
down links whenever they are not used or suitable due to signal strength
etc. The list of peers with which such operations are to be performed
are provided with the TDLS driver operations.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This is a better way of matching P2P groups based on the unique P2P
Device Address (e.g., from P2P Group ID) and SSID pair instead of using
the not necessarily unique P2P Interface Address.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This option can be used to globally configure bgscan parameters
for all the network blocks.
Note that this configuration will not override a network block
specific bgscan settings, but will only be used in case that
the network block does not have a valid bgscan configuration.
Signed-hostap: Haim Dreyfuss <haim.dreyfuss@intel.com>
Add the option to ask for VHT operation similarly to the way ht40 is
configured - either by adding 'vht' param to the relevant p2p_*
commands or by configuring p2p_go_vht=1 in the configuration file.
This patch only adds the configuration option (e.g., via control
interface). The actual handling of the VHT parameter (asking the driver
to use VHT, etc.) will be done by the following patch.
Signed-hostap: Eliad Peller <eliadx.peller@intel.com>
The new p2p_add_cli_chan=1 configuration parameter can be used to
request passive-scan channels to be included in P2P channel lists for
cases where the local end may become the P2P client in a group. This
allows more options for the peer to use channels, e.g., if the local
device is not aware of its current location and has marked most channels
to require passive scanning.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The new p2p_no_go_freq frequency range list (comma-separated list of
min-max frequency ranges in MHz) can now be used to configure channels
on which the local device is not allowed to operate as a GO, but on
which that device can be a P2P Client. These channels are left in the
P2P Channel List in GO Negotiation to allow the peer device to select
one of the channels for the cases where the peer becomes the GO. The
local end will remove these channels from consideration if it becomes
the GO.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The new configuration parameter external_sim=<0/1> can now be used to
configure wpa_supplicant to use external SIM/USIM processing (e.g., GSM
authentication for EAP-SIM or UMTS authentication for EAP-AKA). The
requests and responses for such operations are sent over the ctrl_iface
CTRL-REQ-SIM and CTRL-RSP-SIM commands similarly to the existing
password query mechanism.
Changes to the EAP methods to use this new mechanism will be added in
separate commits.
Signed-hostap: Jouni Malinen <j@w1.fi>
This allows credentials to be limited from being used to connect to a
network unless the AP advertises a matching roaming consortium OI.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This allow domain_suffix_match to be specified for a cred block and then
get this copied for the network blocks generated from this credential as
part of Interworking network selection.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Credentials can now be configured with more than one FQDN ('domain'
field in the cred block) to perform Domain Name List matching against
multiple home domains.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The new domain_suffix_match (and domain_suffix_match2 for Phase 2
EAP-TLS) can now be used to specify an additional constraint for the
server certificate domain name. If set, one of the dNSName values (or if
no dNSName is present, one of the commonName values) in the certificate
must have a suffix match with the specified value. Suffix match is done
based on full domain name labels, i.e., "example.com" matches
"test.example.com" but not "test-example.com".
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
wpa_config_write_key_mgmt has a buffer size of 50. This is not enough
to fit the longest case. I used a network with "WPA-PSK WPA-EAP
WPA-NONE" and CONFIG_IEEE80211R=y + CONFIG_IEEE80211W=y to produce
a string longer than 50 chars. Increase the buffer size to 100 to
prevent truncated output.
Truncated output is not the only problem. If the buffer end is
reached when adding certain key mgmt types the function does not
return immediately. This leaves pos > end. When a second os_sprintf
is called the calculation of end - pos yields a large positive
number for buffer size. End result is a write beyond the buffer end.
Fix this by bailing out if buffer end is reached.
Signed-hostap: Pontus Fuchs <pontus.fuchs@gmail.com>
no_ctrl_interface parsing was declared within ifdef CONFIG_CTRL_IFACE
block, so the parser function needs to be marked similarly.
Signed-hostap: Jouni Malinen <j@w1.fi>
This can be used to override previously set ctrl_interface value in a
way that clears the variable to NULL instead of empty string. The only
real use case for this is to disable per-interface ctrl_interface from
the additional control file (-I<file>) in case ctrl_interface was set in
the main configuration file. It should be noted that zero-length
ctrl_interface parameter can be used to initiate some control interface
backends, so simpler designs were not available for this.
The format of the new parameter is not exactly cleanest due to
configuration file parsing assumptions. For example:
ctrl_interface=....
no_ctrl_interface=
would end up with ctrl_interface=NULL.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
There was already a CFG_CHANGED_P2P_OPER_CHANNEL handler function, but
this flag was not set when the p2p_oper_reg_class or p2p_oper_channel
parameters were changed.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Record all generated per-client PSKs in the persistent group network
block and configure these for the GO Authenticator whenever re-starting
the persistent group. This completes per-client PSK support for
persistent groups.
Signed-hostap: Jouni Malinen <j@w1.fi>
When using OpenSSL with TLS-based EAP methods, wpa_supplicant can now be
configured to use OCSP stapling (TLS certificate status request) with
ocsp=1 network block parameter. ocsp=2 can be used to require valid OCSP
response before connection is allowed to continue.
hostapd as EAP server can be configured to return cached OCSP response
using the new ocsp_stapling_response parameter and an external mechanism
for updating the response data (e.g., "openssl ocsp ..." command).
This allows wpa_supplicant to verify that the server certificate has not
been revoked as part of the EAP-TLS/PEAP/TTLS/FAST handshake before
actual data connection has been established (i.e., when a CRL could not
be fetched even if a distribution point were specified).
Signed-hostap: Jouni Malinen <j@w1.fi>
If a VIF is already associated, then only scan on the associated
frequency if user requests such. This is a big help when using
lots of virtual stations.
Signed-hostap: Ben Greear <greearb@candelatech.com>
Signed-off-by: Ben Greear <greearb@candelatech.com>
The new sched_scan_interval parameter can be used to set the default
sched_scan interval, e.g., for power saving purposes.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This allows one to limit the channels that wpa_supplicant will
scan. This is a useful addition to the freq_list configurable
in the network {} section.
Signed-hostap: Ben Greear <greearb@candelatech.com>
There are quite a few places in the current implementation where a nul
terminated string is generated from binary data. Add a helper function
to simplify the code a bit.
Signed-hostap: Jouni Malinen <j@w1.fi>
This can be used to configure wpa_supplicant to ignore old scan results
from the driver cache in cases where such results were not updated after
the scan trigger from wpa_supplicant. This can be useful in some cases
where the driver may cache information for a significant time and the AP
configuration is changing. Many such cases are for testing scripts, but
this could potentially be useful for some WPS use cases, too.
Signed-hostap: Jouni Malinen <j@w1.fi>
This new parameter allows wpa_supplicant AP mode operations to use
similar design to the vendor_elements parameter in hostapd to add
vendor_elements into Beacon/Probe Response IE parameters.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
