Commit Graph

5519 Commits

Author SHA1 Message Date
Jouni Malinen
27c77751f7 WNM: Fix BSS Transition Management Request processing
The WNM-Sleep Mode handler took over WNM Action frame processing without
addressing the previously implemented WNM handler. Fix this by moving
the BSs Transition Management processing into wnm_sta.c to share a
single handler function for WNM Action frames.

Signed-hostap: Jouni Malinen <j@w1.fi>
2012-12-22 12:02:15 +02:00
Jouni Malinen
a38fdf1c69 Document gas_query.c functions
Signed-hostap: Jouni Malinen <j@w1.fi>
2012-12-22 11:59:26 +02:00
Jouni Malinen
2f3101d8df Move some P2P offchannel operations to offchannel.c
There is no need for p2p_supplicant.c to access wpa_s->pending_action_tx
so move these references to offchannel.c to get a bit cleaner interface
between the components.

Signed-hostap: Jouni Malinen <j@w1.fi>
2012-12-22 11:22:12 +02:00
Jouni Malinen
b4419c62ad Document offchannel Action frame TX functions
Signed-hostap: Jouni Malinen <j@w1.fi>
2012-12-22 11:06:56 +02:00
Jouni Malinen
3ab35a6603 Extend EAPOL frames processing workaround for roaming cases
Commit 1ff733383f added a mechanism to
work around issues due to association events and EAPOL RX events being
getting reordered. However, this applied only for the case where
wpa_supplicant is not in associated state. The same issue can happen in
roaming case with drivers that perform BSS selection internally (or in
firmware). Handle that case similarly by delaying received EAPOL frame
processing if the source address of the EAPOL frame does not match the
current BSSID.

Since wired IEEE 802.1X do not have BSSID, make this additional
workaround conditional on BSSID match having been observed during the
previous association.

This fixes issues where the initial EAPOL frame after reassociation was
either dropped (e.g., due to replay counter not increasing) or replied
to with incorrect destination address (the BSSID of the old AP). This
can result in significantly more robust roaming behavior with drivers
that do not use wpa_supplicant for BSS selection.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-12-21 21:35:35 +02:00
Jouni Malinen
318e772ad1 WPS: Update configuration file after re-enabling networks
Network blocks are disabled during a WPS provisioning step and 10
seconds after this to allow the newly provisioned network to be
selected. The disabled=1 flag gets written to the configuration file
when the credential is added since it happens during this process.
Update the file again after the networks have been re-enabled to avoid
leaving the configuration file into state that is not consistent with
the running configuration.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-12-21 20:11:26 +02:00
Sunil Dutt
6fbcbc07e4 WPS: Optimize post-WPS scan even if EAP-Failure is not received
Commit 17a4734dc4 shall optimize the
post-WPS scan based on the channel used during the provisioning only
when the EAP-Failure frame is received. In cases where the EAP-Failure
frame is missed, this optimization shall not happen resulting in the
scan in all the channels thus consuming more time for the connection.
This commit enhances this by storing the requisite information after
the M8 frame is received.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-12-21 15:30:39 +02:00
Jouni Malinen
8b24861154 Add Acct-Session-Id into Access-Request messages
This optional attribute may make it easier to bind together the
Access-Request and Accounting-Request messages. The accounting session
identifier is now generated when the STA associates instead of waiting
for the actual session to start after successfull authentication.

Signed-hostap: Jouni Malinen <j@w1.fi>
2012-12-18 18:13:31 +02:00
Jouni Malinen
2ec535fd37 WNM: Add option to disable keep-alive frames for testing purposes
"wpa_cli set no_keep_alive 1/0" can now be used to disable/enable
keep alive frames to enable testing.

Signed-hostap: Jouni Malinen <j@w1.fi>
2012-12-18 16:57:52 +02:00
Jouni Malinen
41014724e2 Fix CONFIG_NO_WPA build with TLS
The SHA1 and MD5 functions need to be included in builds that use TLS
even if WPA support is removed.

Signed-hostap: Jouni Malinen <j@w1.fi>
2012-12-18 15:16:00 +02:00
Jouni Malinen
77d7b090e0 Remove compiler warning on CONFIG_NO_WPA build
wpa_supplicant_set_rekey_offload() is used only if CONFIG_NO_WPA is not
defined.

Signed-hostap: Jouni Malinen <j@w1.fi>
2012-12-18 15:14:54 +02:00
Ben Greear
c8d22af88f wpa_supplicant: Document HT capability overrides
Signed-off-by: Ben Greear <greearb@candelatech.com>
2012-12-18 14:49:35 +02:00
Ben Greear
a90497f85f wpa_supplicant: Allow user to disable short guard interval (SGI)
Requires Linux kernel patch to make the SGI-20 properly disabled. SGI-40
will already work since Linux 3.4 or so.

Signed-hostap: Ben Greear <greearb@candelatech.com>
Signed-off-by: Ben Greear <greearb@candelatech.com>
2012-12-18 14:45:09 +02:00
Vladimir Kondratiev
7829894c21 Introduce 60 GHz band
Basic support for the 60 GHz band. Neither P2P nor WPS are yet taken
care off. Allows to start AP with very simple config:

network={
        ssid="test"
        mode=2
        frequency=60480
        key_mgmt=NONE
}

Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-12-18 11:50:35 +02:00
Jouni Malinen
058da39cc9 P2P: Add more complete description of p2p_cancel
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-12-18 11:13:51 +02:00
Jouni Malinen
50178335bf P2P: Allow p2p_cancel to be used to stop p2p_connect-join operation
p2p_cancel did not properly cancel a pending p2p_connect-join operation.
Address the different steps in that process: initial scan, Provision
Discovery exchange before connection, and WPS provisioning step
(including the scans before WPS).

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-12-18 10:39:34 +02:00
Jouni Malinen
03c961e542 Interworking: Default to EAP-MSCHAPv2 with EAP-PEAP
If the NAI Realm list indicates that EAP-PEAP is used, use EAP-MSCHAPv2
as the Phase 2 method by default if the NAI Realm list does not specify
the tunneled method.

Signed-hostap: Jouni Malinen <j@w1.fi>
2012-12-17 23:27:15 +02:00
Sven Eckelmann
f1b44874c2 Fix initialization of ap_table_{max_size,expiration_time}
The config says that the default for ap_table_max_size is 255 and the
default for ap_table_expiration_time is 60. But the code doesn't reflect
the default values mentioned in the sample config file.

These variables completely disable the code for Overlapping Legacy BSS
Condition by default when they are not correctly initialized. WFA
certification requires this feature and therefore an AP would have
failed the certification process unless they were initialized manually
using the configuration file.

Signed-hostap: Sven Eckelmann <sven@open-mesh.com>
Signed-hostap: Simon Wunderlich <simon@open-mesh.com>
2012-12-17 17:54:21 +02:00
Pontus Fuchs
5bbf590a58 hostapd: Android: Force group access to ctrl_iface directory
Same fix as d49ea68284 in
wpa_supplicant.

From original commit:

wpa_supplicant is started from /init.*.rc on Android and that seems
to be using umask 0077 which would leave the control interface
directory without group access. This breaks things since Wi-Fi
framework assumes that this directory can be accessed by other
applications in the wifi group. Fix this by adding group access even
if umask value would prevent this.

Signed-hostap: Pontus Fuchs <pontus.fuchs@gmail.com>
2012-12-17 16:30:44 +02:00
Pontus Fuchs
9cbd5845d0 hostapd: Don't chown control interface to root
If ctrl_interface_group in the config file is set hostapd tries to
chown the dir and socket to uid 0. This causes the chown to fail
if hostapd is run as non-root.

Signed-hostap: Pontus Fuchs <pontus.fuchs@gmail.com>
2012-12-17 16:27:04 +02:00
Jouni Malinen
9904ff876a WPS: Add RF bands attribute conditionally to Probe Response frame
WSC IE in Beacon and Probe Response frames should behave consistently
as far as the RF Bands attribute is concerned. Use the same dualband
condition for adding this into Probe Response frames since the value
is not really needed if the AP is not a dualband AP.

Signed-hostap: Jouni Malinen <j@w1.fi>
2012-12-17 16:08:23 +02:00
Jouni Malinen
cd6be5c246 WPS: Use wps_rf_bands parameter to determine dualband functionality
If separate hostapd processes are used for different RF bands, the
dualband parameter for WPS was not set correctly. Allow dualband
indication (mainly, addition of RF bands attribute for PBC session
overlap detection) also based on wps_rf_bands value (if set to "ag").

Signed-hostap: Jouni Malinen <j@w1.fi>
2012-12-17 16:06:10 +02:00
Jouni Malinen
953d25ca5f HS 2.0: Fix sp_type check in ctrl_iface status command
Commit e99b4f3a14 added functionality to
check whether the current association is with the home SP. This commit
did not take into account that the domain name ANQP information could be
NULL and that could result to a NULL pointer dereference. Fix that by
validation that domain_names != NULL before calling
domain_name_list_contains().

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-12-17 12:12:13 +02:00
Jouni Malinen
0a66ce3c49 WNM: Add support for SSID List element matching
This allows Probe Request frame processing to compare the configured
SSID to the SSID List element in addition to the SSID element.

Signed-hostap: Jouni Malinen <j@w1.fi>
2012-12-16 21:22:24 +02:00
Jouni Malinen
b93c8509cc Add support for advertising UTF-8 SSID extended capability
This field can be used to indicate that UTF-8 encoding is used in the
SSID field.

Signed-hostap: Jouni Malinen <j@w1.fi>
2012-12-16 20:46:51 +02:00
Jouni Malinen
a8e93a1a01 WNM: Skip os_memcpy in wnmtfs_ie is NULL
It is cleaner to skip the memcpy call instead of trusting on the
length parameter being 0 in this case.

Signed-hostap: Jouni Malinen <j@w1.fi>
2012-12-16 19:48:39 +02:00
Jouni Malinen
835822d404 WNM: Fix GTK/IGTK encoding in WNM-Sleep Mode Exit frame
These subelements do not use AES key wrap (MFP is used instead).

Signed-hostap: Jouni Malinen <j@w1.fi>
2012-12-16 19:46:10 +02:00
Jouni Malinen
5d247692f6 Fix wpa_supplicant CONFIG_AP=y build with WNM enabled
Signed-hostap: Jouni Malinen <j@w1.fi>
2012-12-16 19:31:36 +02:00
Jouni Malinen
14df897c7a WNM: Fix memory leak on error path
Signed-hostap: Jouni Malinen <j@w1.fi>
2012-12-16 19:31:25 +02:00
Jouni Malinen
4da10640a7 WNM: Fix AP logic on when to include GTK/IGTK in WNM-Sleep Mode exit
Signed-hostap: Jouni Malinen <j@w1.fi>
2012-12-16 19:27:09 +02:00
Jouni Malinen
615a5d559d WNM: Use defined macros for WNM-Sleep Mode Action Type values (AP)
Signed-hostap: Jouni Malinen <j@w1.fi>
2012-12-16 19:24:06 +02:00
Jouni Malinen
c79938a584 WNM: Enable WNM-Sleep Mode configuration with hostapd SME/MLME
This allows hostapd to process WNM-Sleep Mode Request when using the
internal SME/MLME.

Signed-hostap: Jouni Malinen <j@w1.fi>
2012-12-16 19:16:17 +02:00
Jouni Malinen
ad3872a372 WNM: Use CONFIG_WNM more consistently
Replace CONFIG_IEEE80211V with CONFIG_WNM to get more consistent build
options for WNM-Sleep Mode operations. Previously it was possible to
define CONFIG_IEEE80211V without CONFIG_WNM which would break the build.
In addition, IEEE 802.11v has been merged into IEEE Std 802.11-2012 and
WNM is a better term to use for this new functionality anyway.

Signed-hostap: Jouni Malinen <j@w1.fi>
2012-12-16 18:22:54 +02:00
Jouni Malinen
74b4a3606d WNM: Split WNM-Sleep Mode Response processing into separate functions
Signed-hostap: Jouni Malinen <j@w1.fi>
2012-12-16 13:05:19 +02:00
Jouni Malinen
df80a0ccff WNM: Use defined macros for WNM-Sleep Mode Action Type values
Signed-hostap: Jouni Malinen <j@w1.fi>
2012-12-16 12:57:38 +02:00
Jouni Malinen
0a47a6a747 WNM: Remove unnecessary extra indentation level
Signed-hostap: Jouni Malinen <j@w1.fi>
2012-12-16 12:51:02 +02:00
Jouni Malinen
68db9ab047 WNM: Fix GTK/IGTK parsing for WNM-Sleep Mode Response frame
These fields do not use AES keywrap. Instead, they are protected with
management frame protection (and not included if PMF is disabled).

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-12-16 12:48:34 +02:00
Jouni Malinen
e6955ba9f9 WNM: Add WNM-Sleep Mode into Extended Capabilities element
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-12-16 12:45:59 +02:00
Jouni Malinen
bd896433af nl80211: Register to process WNM-Sleep Mode Response frames
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-12-16 12:42:26 +02:00
Jouni Malinen
44f6d554ee wlantest: Process TX status frames as RX frames too
This is needed to allow capture files from the mac80211 cooked monitor
mode interface to be processed properly. Without this, the locally
generated frames may not get processed.

Signed-hostap: Jouni Malinen <j@w1.fi>
2012-12-16 12:35:07 +02:00
Jouni Malinen
62f6fbb480 WNM: Accept GTK update version of WNM-Sleep Response status
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-12-16 12:33:55 +02:00
Jouni Malinen
e0c54a159b WNM: Use Dialog Token value 1 in WNM-Sleep Mode Request
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-12-16 12:32:53 +02:00
Jouni Malinen
cd0ef65784 WNM: Add option for passing TFS request from external programs
The optional tfs_req=<hex dump> parameter can be added for the wnm_sleep
command to specify the TFS request element to use in the WNM-Sleep Mode
Request frame.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-12-16 12:31:16 +02:00
Jouni Malinen
61c54976f5 WNM: Remove unnecessary path component from includes
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-12-16 12:29:44 +02:00
Jouni Malinen
e9199e3149 WNM: Add ctrl_iface command for sending WNM-Sleep Mode Request
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-12-16 12:29:10 +02:00
Jouni Malinen
2dfb9a447c WNM: Fix CONFIG_WNM use in Makefile
This code was within ifdef CONFIG_AP and did not get included unless
AP mode support was also enabled.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-12-16 12:28:19 +02:00
Jouni Malinen
9af431035f WNM: Remove unused variable
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-12-16 12:27:38 +02:00
Jouni Malinen
dbea8ac7ab Interworking: Allow SSID-based network exclusion for credentials
The new excluded_ssid parameter within a cred block can be used to
excluded networks from matching with credentials.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-12-16 12:01:50 +02:00
Jouni Malinen
9aae09f196 Interworking: Fix cred saving
Number of cred block fields were not saved when wpa_supplicant is
writing the configuration file.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-12-16 12:00:52 +02:00
Jouni Malinen
2047e596ec Interworking: Default to TTLS/MSCHAPv2 for NAI Realm list matching
If the AP does not advertize EAP parameters, default to TTLS/MSCHAPv2
when using username/password credentials.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-12-16 12:00:06 +02:00