This commit enhances the existing implementation of abort scan to also
abort concurrent active vendor scans. This is achieved by passing the
the scan_cookie to the driver interface with the intention to abort
the specific scan request. This scan_cookie is returned from the driver
interface when the scan request is scheduled.
This scan_cookie is 0 if the scan is triggered through the upstream
cfg80211 interface. Thus, the scan_cookie is used to determine whether
to abort the cfg80211 or vendor scan request.
Also, the previous implementation of relying on scan_work/p2p_scan_work
for the active work to trigger the abort scan is enhanced to check for
the started state of either of these work operations. This should also
help to abort the concurrent active scan/p2p-scan operations.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This commit adds IP address information into GroupStarted event on the
P2P client side like it is sent over the control interface.
Signed-off-by: Nishant Chaprana <n.chaprana@samsung.com>
When starting ASP provisioning with connection capability set to NEW,
don't create the pending P2P interface as a GO interface because
Go negotiation will determine which side will be the GO and it is
possible that eventually this interface will become the client.
In this case, when the P2P client is started it will start scanning
and do other station specific operations while the interface type
is AP.
Instead, use type WPA_IF_P2P_GROUP when creating the interface which
means the interface type will be determined later.
Signed-off-by: Avrahams Stern <avraham.stern@intel.com>
Filter out get_pref_freq_list() (i.e.,
QCA_NL80211_VENDOR_SUBCMD_GET_PREFERRED_FREQ_LIST) output in case of
channel negotiation by removing channels that do not allow P2P operation
at all. Previously, only the explicitly disallowed channels were removed
and that could have resulted in selecting an operating channel that is
not allowed for P2P and failing to complete the operation to start the
group.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
When starting a P2P GO, the struct p2p_go_neg_results may use
persistent_group == 2 to indicate use of persistent reconnect. Setting
ssid->p2p_persistent_group based on this did not take into account this
special case and that ended up in D-Bus code trying to encode 2 as a
DBUS_TYPE_BOOLEAN value which results in an assert from the library. Fix
this by setting ssid->p2p_persistent_group to 0 or 1 instead of raw
params->persistent_group value without any filtering.
This is similar to an earlier fix in commit
112fdee738 ('P2P: Fix D-Bus persistent
parameter in group started event') that addressed another code path in
sending out this D-Bus signal.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
wpas_p2p_persistent_group() returns non-zero for persistent groups. This
value happens to be 2 instead of 1 due to the
P2P_GROUP_CAPAB_PERSISTENT_GROUP value. This ended up with D-Bus code
trying to encode 2 as a DBUS_TYPE_BOOLEAN value which results in an
assert from the library. Fix this by modifying
wpas_p2p_persistent_group() to return 0 or 1 instead of 0 or an
arbitrary non-zero.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This allows P2P Listen to be offloaded to device to enhance power
saving.
To start P2P listen offload, from wpa_cli interface, issue the command:
p2p_lo_start <freq> <period> <interval> <count>
To stop P2P listen offload, issue the command:
p2p_lo_stop
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This adds an extra parameter in GroupStarted signal to indicate whether
the created group is Persistent or not. It is similar to the
[PERSISTENT] tag which comes in P2P-GROUP-STARTED over the control
interface.
Signed-off-by: Nishant Chaprana <n.chaprana@samsung.com>
This allows using P2PS config method with or without PIN for connection.
wpa_supplicant should internally handle the default PIN "12345670" and
shall also allow connection irrespective of PIN used in P2P_CONNECT.
For example,
1. P2P_CONNECT 02:2a:fb:22:22:33 p2ps
2. P2P_CONNECT 02:2a:fb:22:22:33 xxxxxxxx p2ps
Where the second one is maintained for backwards compatibility.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
wpa_supplicant was starting P2P group processing for all AP mode
interfaces in CONFIG_P2P=y builds. This is unnecessary and such
operations should be enabled only for actual GO interfaces.
Signed-off-by: Jouni Malinen <j@w1.fi>
When the P2P Device interface is used and an existing interface is used
for P2P GO/Client, the P2P Device configuration was not cloned to the
configuration of the existing interface. Thus, configuration parameters
such as idle_group_time, etc., were not propagated to the P2P GO/Client
interface.
Handle this by copying all configuration parameters of the P2P device
interface to the reused interface, with the following exceptions:
1. Copy the NFC key data only if it was not set in the configuration
file.
2. The WPS string fields are set only if they were not previously set
in the configuration of the destination interface (based on the
assumption that these fields should be identical among all
interfaces).
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Use the p2pdev pointer instead of the parent pointer to comply with the
flows when a dedicated P2P Device interface is used and
p2p_no_group_iface == 1 (in which case the parent of the reused
interface isn't necessary the same as p2pdev).
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Trigger an event when wpa_supplicant accepts an invitation to re-invoke
a persistent group. Previously wpa_supplicant entered group formation
without triggering any specific events and it could confuse clients,
especially when operating with a driver that does not support
concurrency between P2P and infrastructure connection.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Fix two problems with storage of 60 GHz P2P persistent groups:
1. pbss flag was not stored in the network block.
2. When recreating the persistent group from storage,
in addition to the missing pbss flag, the pairwise_cipher and
group_cipher were initialized to CCMP which does not work
in 60 GHz since the default in 60 GHz should be GCMP.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
This group capability bit was previously added unconditionally which
could result in the P2P Client assuming the functionality is available
even though the GO would always reject the request (not reply to it with
an assigned IP address) during the 4-way handshake.
Fix this by advertising the capability only if the GO configuration
allow IP address assignment to be completed.
Signed-off-by: Jouni Malinen <j@w1.fi>
Make sure wpas_p2p_init_go_params() respects the p2p_ignore_shared_freq
configuration option. Choose currently used frequencies only if this
option is not set, or if there are no unused channels left.
Signed-off-by: Eliad Peller <eliad@wizery.com>
When p2p_find is stopped, send request to the driver
in order to cancel an ongoing scan if there is one.
Signed-off-by: Ben Rosenfeld <ben.rosenfeld@intel.com>
When building P2P IE for Probe Request frames in P2P scan, add the
device information attribute if the 60 GHz band is included in the scan,
since this is required by the P2P specification.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
When setting up parameters for P2P scan, calculate the frequencies
for the scan before calculating the scan IE. This is because
the scan IE calculation may need information about the scan
frequencies in use.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Add support for drivers with dedicated P2P_DEVICE interface, but without
group interface concurrency (only a single netdev is used). With such
devices, wpa_supplicant tried to use the p2p_dev interface instead of
the group interface and most P2P operations failed. Extend
wpa_supplicant to use the primary interface instead of a separate group
interface in such cases.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
In many places in the code there was a reference to wpa_s->parent to get
from group interface to p2p_dev interface. These places can break if
P2P_DEVICE interface would need to be used with the primary interface as
the group interface, since the parent of the primary interface points to
itself and not the p2p_dev interface.
Fix this by adding a separate "p2pdev" pointer to wpa_supplicant,
it will be the same as parent pointer in most cases but whenever
the primary interface is used as a group interface, change it to
point to the correct p2p_dev interface.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Add definitions for global operating classes. These definitions will be
used to construct supported operating classes information element.
The operating classes definitions used locally for P2P module will be
removed and included in the general operating classes definitions.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Remove the fallback dependency on os_random() when generating a WPS pin.
This is exceptionally unlikely to ever be called as the call to
os_get_random() is unlikely to fail. The intention is to facilitate
future removal of os_random() as it uses a low quality PRNG.
Signed-off-by: Nick Lowe <nick.lowe@lugatech.com>
PBSS (Personal Basic Service Set) is a new BSS type for DMG
networks. It is similar to infrastructure BSS, having an AP-like
entity called PCP (PBSS Control Point), but it has few differences.
PBSS support is mandatory for IEEE 802.11ad devices.
Add a new "pbss" argument to network block. The argument is used
in the following scenarios:
1. When network has mode=2 (AP), when pbss flag is set will start
as a PCP instead of an AP.
2. When network has mode=0 (station), when pbss flag is set will
connect to PCP instead of AP.
The function wpa_scan_res_match() was modified to match BSS according to
the pbss flag in the network block (wpa_ssid structure). When pbss flag
is set it will match only PCPs, and when it is clear it will match only
APs.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Previously it was possible for the pending Action frame TX to be
cleared, but the offchannel TX operation being left in wait state in the
kernel. This would delay start of the next operation (e.g., that listen
operation requested by P2P_LISTEN) until the wait time for the
previously pending Action frame had expired.
Optimize this by explicitly stopping any pending offchannel Action frame
TX when clearing the internal offchannel TX state in
wpas_p2p_clear_pending_action_tx().
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
At least one of the wpas_p2p_connect() callers (NFC join case) already
had access to the Group SSID. Pass that information through
wpas_p2p_connect() to wpas_p2p_join() so that the join operation can
filter out incorrect groups more easily.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Accept only a BSS entry matching the SSID when trying to find the
operating channel of a GO during join operation for which the SSID was
already specified. Previously, it could have been possible to pick an
incorrect BSS entry if the new GO was not found in the latest scan and
there was an older cached scan entry for the same BSSID.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
It was already possible to limit join operation to accept only a
specific SSID. However, this constraint was not used when starting a P2P
Client interface as a WPS Enrollee without going through a Provision
Discovery exchange.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Use wpa_bss_get() with the specific Group SSID instead of
wpa_bss_get_bssid_latest() if the SSID is already known. This makes the
P2P join operations more robust in case the frequency of the group was
not yet known and the same P2P Interface Address may have been used in
multiple group instances with an older group entry still present in the
cached scan results.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This allows the cases where a specific group SSID is known to filter out
groups on the P2P Client even if the specific BSS entry for the target
group is not yet available.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The new optional group_ssid=<hexdump> argument in the P2PS-PROV-DONE
event can be used to help in identifying the exact group if there have
been multiple groups with the same P2P Interface Address in short period
of time.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Commit f8a80e39b3 ('P2PS: Change
connection capability handling') added the identical P2PS_SETUP_CLIENT
check into two places within p2ps_group_capability(). However, only the
first one of these can be reached. In the second case, role can only
have values 0 or P2PS_SETUP_NEW and as such, the P2PS_SETUP_CLIENT case
is not possible. It looks like the first part of the commit is
sufficient, so remove the dead code added by the second part.
Signed-off-by: Jouni Malinen <j@w1.fi>
Fix wpas_p2p_invite() to call p2p_set_own_pref_freq_list() after the
NULL check, to avoid NULL pointer dereference if P2P initialization were
to have failed or P2P module getting deinitialized.
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
This was already working for the case where a separate group interface
is used due to the recent commit
328f49acfe ('P2P: Complete group formation
on client data connection'). However, the case of no separate group
interface was used did not clear the interface state properly on data
connection. Fix this by setting the group formation information in
wpas_start_p2p_client().
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Commit f05cee9714 ('P2P: Clear
p2p_in_invitation on cancel') added a wpas_p2p_cancel() case to call
wpas_p2p_group_formation_failed() if wpa_s->p2p_in_invitation is set.
This is done in a loop going through wpa_s->next pointers. However, the
call here can result in removing the interface and freeing wpa_s. The
following attempt to read wpa_s->next is from freed memory and that can
result in process termination when using a separate P2P group interface
and issuing P2P_CANCEL on a group that was started through re-invocation
of a persistent group.
The recent commit 328f49acfe ('P2P:
Complete group formation on client data connection') "fixed" this by
accident since wpa_s->p2p_in_invitation gets cleared in the sequence
that could hit this issue and this results in P2P_CANCEL getting
rejected. However, the real bug here is in the loop that continues after
possible wpa_s instance deletion. Fix that by breaking out of the loop.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This was already the case in the GO role where the first client
connection is waited before marking
wpa_s->p2p_go_group_formation_completed = 1 and clearing
wpa_s->global->p2p_group_formation. However, in the P2P Client role,
that was done already at the completion of the WPS exchange. This can be
problematic since group formation timeout may still try to clear the
group and with wpa_s->global->p2p_group_formation == NULL, the correct
group interface may not be found.
Fix this by postponing clearing of wpa_s->global->p2p_group_formation on
the P2P Client side until the data connection has been completed and
group is declared started.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
A hwsim test sequence was able to hit a SIGSEGV in
p2p_go_save_group_common_freqs() called by p2p_go_configured() callback
in a case where a non-P2P AP mode operation is started in wpa_supplicant
(wpas_ap_wep test case). This callback should not have happened for
non-P2P case and the debug logs did not make it clear how this could
happen. In addition, it is unclear how this could be reproduced.
To avoid this type of issues, clear the wpa_s->ap_configured_cb pointer
as soon as the first call to the function happens. In addition, verify
that wpa_s->go_params is available before processing the GO configured
callback.
Signed-off-by: Jouni Malinen <j@w1.fi>
The new max_oper_chwidth and freq2 arguments to P2P_CONNECT, P2P_INVITE,
and P2P_GROUP_ADD control interface commands can be used to request
larger VHT operating channel bandwidth to be used than the previously
used maximum 80 MHz.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This extends the previous design that covered only the VHT 80 MHz cases
for VHT channel flags. New functions are introduced to allow 160 MHz
bandwidth cases to determine the center channel and check availability
of a 160 MHz channel.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This adds definitions for the global operating classes 129 and 130 for
VHT 80+80 MHz and 160 MHz use cases.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
When an invitation to join an existing group is accepted by the
peer device, set p2p_go_wait_client to the current time so
that wpas_p2p_in_progress() would return != 0, thus preventing
P2P CSA, scanning etc., that would interfere with the peer
device connection.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
When clearing pending TX action to start a new P2P operation like
P2P_FIND or P2P_LISTEN, wpas_p2p_action_tx_clear() was used to clear
the send action work. However, in cases where the action work has wait
time, it is not cleared immediately but only after the wait time ends.
This may cause delay in starting the P2P operation.
Fix that by always clearing the send action work immediately on these
P2P commands that result in immediate P2P state change and practically
stopping a previous operation, if one was pending.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
This makes it easier to analyze debug logs for issues related to
multiple pending Action TX frames.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
When one peer doesn't include a persistent group info in PD Request
the other peer shouldn't report a persistent group usage with this
peer even if such a persistent group exists locally. This condition
could be violated in the previous implementation.
In case a local persistent group exists and the
wpas_p2ps_prov_complete() function is called with persist_ssid parameter
set to NULL, wpa_supplicant reported P2PS-PROV-DONE with persist=<idx>
instead of conncap=<role> parameter.
This happened because the wpas_p2p_get_persistent() function was called
without verification whether the persist_ssid was set to NULL. In this
case the wpas_p2p_get_persistent() returns the first existing persistent
group matching the P2P Device Address without verifying the group's
SSID. After that the group ID is used as persist=<idx> parameter of
P2PS-PROV-DONE event.
Fix the issue by adding persist_ssid and persist_ssid_size verification
as a condition for the wpas_p2p_get_persistent() call.
Signed-off-by: Max Stepanov <Max.Stepanov@intel.com>
On successful P2P PD, report the chosen frequency in case the local
device is going to be the P2P GO, so in can later be used to instantiate
the new P2P GO, etc.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Add operating channel selection and channel list processing similar to
that done when building GO Negotiation Request, i.e., consider the
currently used channels, configured channels, etc.
P2PS introduces a flow where a responder needs to provide channel data
without being previously aware of the current constraints, i.e., the
channels currently in use by other interfaces. To handle this, extend
the get_group_capability() callback to also handle channel selection
aspects of group capabilities.
In case there is an active P2P GO that is going to be used for the P2PS
PD, force its current operating frequency in the PD attributes.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
