rsn_ie_proto_eap_sta followed by eap_ttls_mschapv2_session_resumption
showed a failure case where the special RSNE from rsn_ie_proto_eap_sta
ended up remaining in a wpa_supplicant BSS entry and the SELECT_NETWORK
command used the previous scan results without checking for changed AP
configuration. This resulted in test failure due to RSN IE being claimed
to be different in EAPOL-Key msg 3/4. This is not really a real world
issue, but try to avoid false failure reports by explicitly clearing the
BSS table at the end of rsn_ie_proto_eap_sta.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The previously used 10 second timeout allowed only two scan attempts
(five seconds between scans) and it was possible to hit a failure every
now and then when running under heavy load and the Probe Response frame
got delayed by 40 ms or so twice in a row. Add more time for one more
scan attempt to reduce the likelihood of this happening.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This is needed for number of EAP test cases at least when using the
internal TLS server implementation.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This adds some more test coverage for phase1 parameters that had not
previously been included in any of the test cases.
Signed-off-by: Jouni Malinen <j@w1.fi>
The decrypted copy of a GTK from EAPOL-Key is cleared from memory only
after having sent out CTRL-EVENT-CONNECTED. As such, there was a race
condition on the test case reading the wpa_supplicant process memory
after the connection. This was unlikely to occur due to the one second
sleep, but even with that, it would be at least theorically possible to
hit this race under heavy load (e.g., when using large number of VMs to
run parallel testing). Avoid this by running a PING command to make sure
wpa_supplicant has returned to eloop before reading the process memory.
This should make it less likely to report false positives on GTK being
found in memory.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
It looks like it is possible for the GTK to be found from memory every
now and then. This makes these test cases fail. Write the memory
addresses in which the GTK was found to the log to make it somewhat
easier to try to figure out where the key can be left in memory.
Signed-off-by: Jouni Malinen <j@w1.fi>
This verifies client private key use in encrypted PKCS #8 format with
PKCS #5 v1.5 format using pbeWithMD5AndDES-CBC and PKCS #5 v2.0 format
using PBES2 with des-ede3-cbc.
Signed-off-by: Jouni Malinen <j@w1.fi>
The internal TLS implementation in wpa_supplicant supports TLS v1.2, so
verify that this version can be disabled.
Signed-off-by: Jouni Malinen <j@w1.fi>
Since the internal TLS client implementation in wpa_supplicant now has
sufficient support for this functionality, allow the test case to be
executed.
Signed-off-by: Jouni Malinen <j@w1.fi>
Verify OCSP stapling response that is signed by the CA rather than a
separate OCSP responder. In addition, verify that invalid signer
certificate (missing OCSP delegation) gets rejected.
Signed-off-by: Jouni Malinen <j@w1.fi>
These test cases left at least one of the attached monitor sockets
blocking for excessive time: ap_wpa2_eap_aka_ext,
ap_hs20_req_conn_capab_and_roaming_partner_preference,
ap_hs20_min_bandwidth_and_roaming_partner_preference, ap_wpa_ie_parsing.
Signed-off-by: Jouni Malinen <j@w1.fi>
Number of test cases did not read all control interface socket events
from the dynamically added wlan5 interface. This could result in hitting
maximum socket TX queue length and failures in the following test cases.
Signed-off-by: Jouni Malinen <j@w1.fi>
This verifies that ENABLE_NETWORK does not trigger reconnection if
already connected. The previous commit fixed a case where it was
possible for that to happen.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
It looks like NID_X9_62_prime192v1 is not available, so allow that group
to fail without failing the full ap_wpa2_eap_pwd_groups test case.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
omac1_aes_128() implementation within crypto_openssl.c is used in this
case and that cannot fail the memory allocation similarly to the
non-FIPS case and aes-omac1.c.
Signed-off-by: Jouni Malinen <j@w1.fi>
OpenSSL rejects the cipher string 'EXPORT' in FIPS mode in a way that
results in the locally generated error showing up before the EAP method
has been accepted.
Signed-off-by: Jouni Malinen <j@w1.fi>
