Now that there is a kernel patch for IPv6 ProxyARP that is capable of
using the non-AP STAs MAC address as the link layer source address in
NA, validate that behavior rather than the temporary check for BSSID.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
It looked like cfg80211 BSS entry for the zero-length SSID could remain
after this test case. Stop the AP and scan twice with flush-cache option
to make this less likely to occur and cause issues to following test
cases.
Signed-off-by: Jouni Malinen <j@w1.fi>
Fix the destination address that is sent in the WNM-Notification to be
the BSS address opposed to the P2P address.
Signed-off-by: Matti Gottlieb <matti.gottlieb@intel.com>
Use another AP instance as a separate bridge port in the proxyarp_open
test cases to increase testing coverage for kernel proxyarp
functionality.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This test case uses get_bss() with a BSSID to find a BSS entry. That can
result in failures if there are multiple BSS entries in wpa_supplicant
BSS table for the same BSSID, e.g., due to an earlier hidden SSID test
case. Explicitly clear the cfg80211 and wpa_supplicant scan caches at
the beginning of this test case to make it less likely for earlier test
cases to trigger a failure here.
Signed-off-by: Jouni Malinen <j@w1.fi>
This step requires kernel changes that are not yet in upstream Linux
tree, so mark this as skip rather than failure for now.
Signed-off-by: Jouni Malinen <j@w1.fi>
This makes it easier to figure out what happened if the test case fails
due to not finding all the needed OSU-PROVIDER information.
Signed-off-by: Jouni Malinen <j@w1.fi>
This is a regression test case to detect a failure that resulted in an
up to five second busy loop through wpa_supplicant_fast_associate() when
interworking_find_network_match() and wpa_supplicant_select_bss() get
different matching results.
Signed-off-by: Jouni Malinen <j@w1.fi>
With GnuTLS, domain_suffix_match is currently requiring full match, so
split the test cases in a way that can be reported more cleanly as PASS
or SKIP based on TLS library behavior.
Signed-off-by: Jouni Malinen <j@w1.fi>
Proper configuration should be used here to get server validation
enabled, so update the test cases to provide the ca_cert parameter. This
was included in number of existing test cases, but not all.
Signed-off-by: Jouni Malinen <j@w1.fi>
Check wpa_supplicant EAP capability and skip EAP-pwd and EAP-FAST test
cases if the build did not include support for these. This is cleaner
than reporting failures for such test cases when the selected TLS
library does not support the EAP method.
Signed-off-by: Jouni Malinen <j@w1.fi>
Instead of returning "skip" from the test function, raise the new
HwsimSkip exception to indicate a test case was skipped.
Signed-off-by: Jouni Malinen <j@w1.fi>
There were couple of typos in the IP addresses and there was no coverage
for the normal unicast ARP response from the bridge (since non-wireless
device does not get proxied by the AP). In addition, it is better to
change the IP address used here to be unique to make the sniffer logs
easier to interpret.
Signed-off-by: Jouni Malinen <j@w1.fi>
This adds transmission of number of NS/NA frames to test ProxyARP
behavior. The actual validation of the AP behavior is still manual,
i.e., a separate inspectation of the capture files is needed.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This avoids one more cleanup step between most test cases by clearing
the default PMF behavior change only in case it was actually modified
during a test.
Signed-off-by: Jouni Malinen <j@w1.fi>
This verifies processing of various ARP messages at an AP that enables
ProxyARP. All the validation steps have not yet been scripted, i.e., the
sniffer traces need manual analysis for full coverage.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This increases wpa_supplicant_ie_txt(), print_bss_info(), and
wpa_supplicant_ctrl_iface_scan_result() testing coverage to include the
previously missing key management options.
Signed-off-by: Jouni Malinen <j@w1.fi>
This makes it more convenient and consistent to clear the cached scan
results from cfg80211 and wpa_supplicant.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This is more robust and extensible than configuring IPv6 addresses on
the interfaces and trying to use ping6 or some other external tools to
generate suitable IPv6 frames.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Use scan_for_bss() instead of scan() to avoid errors if the active scan
fails, e.g., due to heavy load under parallel-vm.sh test run.
Signed-off-by: Jouni Malinen <j@w1.fi>
It looks like mac80211 scan-while-associated can now take over 10
seconds with the current wireless-regdb rules for world roaming due to
number of additional DFS channel having been enabled for passive
scanning. This resulted in ap_hs20_session_info failing due to the wait
for the scan result event timing out. That is not really a real failure,
so increase the timeout to avoid reporting this incorrectly.
Signed-off-by: Jouni Malinen <j@w1.fi>
If the previuous test case used a non-RSN AP and that was left in
cfg80211 scan results, it was possible for ap_hs20_random_mac_addr to
pick that old AP from the previous test and reject to connect through
Hotspot 2.0 mechanisms. Work around this test issue by requesting new
set of scan result at the beginning of the test.
Signed-off-by: Jouni Malinen <j@w1.fi>
Some of the test cases where using INTERWORKING_SELECT internally
without using scan_for_bss like the helper functions did. Add explicit
scan_for_bss calls to make the test cases less likely to fail due to
missing BSSes in scan results. This could cause false failure reports
when runnign under heavy load with parallel-vm.sh.
Signed-off-by: Jouni Malinen <j@w1.fi>
