This patch replaces the station's ht capability information with the
negotiated one in NL80211_CMD_NEW_STATION. This negotiated ht
capability will be needed for rate control initialization in the
driver.
Signed-off-by: vasanth <vasanth@atheros.com>
The EAP server state machine will need to have special code in
getDecision() to avoid starting passthrough operations before having
completed Identity round in the beginning of reauthentication. This was
broken when moving into using the full authenticator state machine from
RFC 4137 in 0.6.x.
The old behavior of generating new DH keys can be maintained for non-OOB
cases and only OOB (in this case, with UFD) will use the pre-configured
DH keys to allow the public key hash to be checked.
Not all embedded devices have USB interface and it is useful to be able
to remove unneeded functionality from the binary. In addition, the
current implementation has some UNIX specific calls in it which may make
it not compile cleanly on all target systems.
Reduce startWhen from 3 to 1 second if WPS is included in the build.
While this is done regardless of runtime WPS configuration, it is fine
to use a smaller value here in general. This cuts two seconds out from
WPS negotiation if the driver does not support addition of WPS IE into
the (Re)Association Request frame.
Need to set WLAN_STA_WPS and WLAN_STA_MAYBE_WPS flags even if WPA is not
enabled. This allows open and static WEP modes to initiate WPS
negotiation with madwifi-like drivers.
Previously, both CONFIG_IEEE80211W=y and CONFIG_IEEE80211R=y were needed
to enable SHA256-based key handshake (WPA-PSK-SHA256 and
WPA-EAP-SHA256). This can now be done with just CONFIG_IEEE80211W=y.
This uses similar, but not identical, interface to madwifi. It is easier
to keep this separate to avoid conflicts with potential changes in the
driver interfaces.
It seems that WFA WPS spec says that default key index should be 1 (not
0). I think this meas that WEP key indexes region is not from 0 to 3,
but from 1 to 4 in WPS. At least WRT610N implemented it this way.
These flags are used to mark which values (level, noise, qual) are
invalid (not available from the driver) and whether level is using dBm.
D-Bus interface will now only report the values that were available.
TX/RX bytes are now reported correctly (typo ended up leaving TX bytes
uninitialized and set RX bytes value to use correct TX bytes). TX/RX
packet counts are not yet available from kernel, so we have to clear the
values to avoid reporting bogus data.
If session resumption fails for any reason, do not try it again because
that is just likely to fail. Instead, drop back to using full
authentication which may work. This is a workaround for servers that do
not like session resumption, but do not know how to fall back to full
authentication properly.
This fixes an issue where two AKA'/Challenge messages are received when
resynchronizing SEQ#. Previously, this used to trigger an authentication
failure since the second Challenge message did not duplicate AT_KDF.
If the driver reports support for more than one SSID per scan request,
optimize scan_ssid=1 operations in ap_scan=1 mode. This speeds up
scanning whenever scan_ssid=1 is used since the broadcast SSID can be
included in every scan request and if driver supports more than two
SSIDs in the scan request, the benefits are even larger when multiple
networks have been configured with ap_scan=1.
This is also cleaning up wpa_supplicant_scan() function by moving code
around so that the SSID list is not processed unnecessarily if the
operation mode does not need this.
This does not actually send out separate scan requests for each SSID,
but the debug output can be used to test scan2() functionality with
multiple SSIDs.
This can be used to provide support for scanning multiple SSIDs at a
time to optimize scan_ssid=1 operations. In addition, Probe Request IEs
will be available to scan2() (e.g., for WPS PBC scanning).
For example, -Dnl80211,wext could be used to automatically select
between nl80211 and wext. The first driver wrapper that is able to
initialize the interface will be used.
This workaround was needed with some drivers that used WEXT, but there
is no known nl80211-enabled driver that would need this, so lets get rid
of the extra delay.
The driver wrappers can now inform wpa_supplicant how many SSIDs can
be used in a single scan request (i.e., send multiple Probe Requests
per channel). This value is not yet used, but it can eventually be used
to allow a new scan command to specify multiple SSIDs to speed up
scan_ssid=1 operations. In addition, a warning could be printed if
scan_ssid=1 is used with a driver that does not support it
(max_scan_ssids=0).
