The new acs_chan_bias configuration parameter is a space-separated list
of <channel>:<bias> pairs. It can be used to increase (or decrease) the
likelihood of a specific channel to be selected by the ACS algorithm.
The total interference factor for each channel gets multiplied by the
specified bias value before finding the channel with the lowest value.
In other words, values between 0.0 and 1.0 can be used to make a channel
more likely to be picked while values larger than 1.0 make the specified
channel less likely to be picked. This can be used, e.g., to prefer the
commonly used 2.4 GHz band channels 1, 6, and 11 (which is the default
behavior on 2.4 GHz band if no acs_chan_bias parameter is specified).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This allows vendor specific information element to be used to advertise
support for VHT on 2.4 GHz band. In practice, this is used to enable use
of 256 QAM rates (VHT-MCS 8 and 9) on 2.4 GHz band.
This functionality is disabled by default, but can be enabled with
vendor_vht=1 parameter in hostapd.conf if the driver advertises support
for VHT on either 2.4 or 5 GHz bands.
Signed-off-by: Yanbo Li <yanbol@qti.qualcomm.com>
The new hostapd.conf radio_measurements parameter can now be used to
configure a test build to advertise support for radio measurements with
neighbor report enabled. There is no real functionality that would
actually process the request, i.e., this only for the purpose of minimal
STA side testing for now.
Signed-off-by: Jouni Malinen <j@w1.fi>
Derive rRK and rIK on EAP server if ERP is enabled and use these keys to
allow EAP re-authentication to be used and to derive rMSK.
The new hostapd configuration parameter eap_server_erp=1 can now be used
to configure the integrated EAP server to derive EMSK, rRK, and rIK at
the successful completion of an EAP authentication method. This
functionality is not included in the default build and can be enabled
with CONFIG_ERP=y.
Signed-off-by: Jouni Malinen <j@w1.fi>
hostapd can now be configured to transmit EAP-Initiate/Re-auth-Start
before EAP-Request/Identity to try to initiate ERP. This is disabled by
default and can be enabled with erp_send_reauth_start=1 and optional
erp_reauth_start_domain=<domain>.
Signed-off-by: Jouni Malinen <j@w1.fi>
hostapd was still providing couple of parameters that were used only in
the already removed driver_test.c framework.
Signed-off-by: Jouni Malinen <j@w1.fi>
This patch makes four MIB variables for plink configurable and sets the
correct default values based on IEEE Std 802.11s-2011.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
New kernels in wiphy_suspend() will call cfg80211_leave_all() that will
eventually end up in cfg80211_stop_ap() unless wowlan_triggers were set.
For now, use the parameters from the station mode as-is. It may be
desirable to extend (or constraint) this in the future for specific AP
mode needs.
Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
Proxy ARP allows the AP devices to keep track of the hardware address to
IP address mapping of the STA devices within the BSS. When a request for
such information is made (i.e., ARP request, Neighbor Solicitation), the
AP will respond on behalf of the STA device within the BSS. Such
requests could originate from a device within the BSS or also from the
bridge. In the process of the AP replying to the request (i.e., ARP
reply, Neighbor Advertisement), the AP will drop the original request
frame. The relevant STA will not even know that such information was
ever requested.
This feature is a requirement for Hotspot 2.0, and is defined in IEEE
Std 802.11-2012, 10.23.13. While the Proxy ARP support code mainly
resides in the kernel bridge code, in order to optimize the performance
and simplify kernel implementation, the DHCP snooping code was added to
the hostapd.
Signed-off-by: Kyeyoon Park <kyeyoonp@qca.qualcomm.com>
Add routines to (de)initialize mesh interface data structures and
join and leave mesh networks.
Signed-off-by: Javier Lopez <jlopex@gmail.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: Jason Mobarak <x@jason.mobarak.name>
Signed-off-by: Thomas Pedersen <thomas@noack.us>
The new "bss_load_update_period" parameter can be used to configure
hostapd to advertise its BSS Load element in Beacon and Probe Response
frames. This parameter is in the units of BUs (Beacon Units).
When enabled, the STA Count and the Channel Utilization value will be
updated periodically in the BSS Load element. The AAC is set to 0 sinze
explicit admission control is not supported. Channel Utilization is
calculated based on the channel survey information from the driver and
as such, requires a driver that supports providing that information for
the current operating channel.
Signed-off-by: Kyeyoon Park <kyeyoonp@qca.qualcomm.com>
The new openssl_cipher configuration parameter can be used to select
which TLS cipher suites are enabled when hostapd is used as an EAP
server with OpenSSL as the TLS library.
Signed-off-by: Jouni Malinen <j@w1.fi>
The current RADIUS server pointer was updated after each SET command
which broke parsing of multiple RADIUS servers over the control
interface. Fix this by doing the final RADIUS server pointer updates
only once the full configuration is available.
Signed-off-by: Jouni Malinen <j@w1.fi>
"user" MACACL "password" style lines in the eap_user file can now be
used to configured user entries for RADIUS-based MAC ACL.
Signed-off-by: Jouni Malinen <j@w1.fi>
This allows hostapd to set a different management group cipher than the
previously hardcoded default BIP (AES-128-CMAC). The new configuration
file parameter group_mgmt_cipher can be set to BIP-GMAC-128,
BIP-GMAC-256, or BIP-CMAC-256 to select one of the ciphers defined in
IEEE Std 802.11ac-2013.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Different channels allow different transmission power, at least in ETSI
countries. Also, ETSI requires a "channel plan" for DFS operation, and
channels should be randomly choosen from these channels.
Add a channel list configuration option for users to add channels
hostapd may pick from.
Signed-hostap: Simon Wunderlich <sw@simonwunderlich.de>
This extends the design already available for Access-Request packets to
the RADIUS server and Access-Accept messages. Each user entry can be
configured to add arbitrary RADIUS attributes.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The new hostapd.conf parameter subscr_remediation_url can be used to
define the URL of the Subscription Remediation Server that will be added
in a WFA VSA to Access-Accept message if the SQLite user database
indicates that the user need subscription remediation.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
hostapd can now be configured to advertise OSU Providers with the
new osu_* confgiuration parameters.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
hostapd can now be configured to provide access for icon files
(hs20_icon config file parameter) for OSU. The hs20_icon data contains
additional meta data about the icon that is not yet used, but it will be
needed for the OSU Providers list ANQP element.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
If the RADIUS server includes deauthentication request in Access-Accept,
send a WNM-Notification frame to the station after 4-way handshake and
disconnect the station after configurable timeout.
A new control interface command, WNM_DEAUTH_REQ, is added for testing
purposes to allow the notification frame to sent based on local request.
This case does not disconnect the station automatically, i.e., a
separate control interface command would be needed for that.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The HS 2.0 Indication element from hostapd now includes the release
number field and the new ANQP Domain ID field. This ID can be configured
with anqp_domain_id parameter in hostapd.conf.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Add configuration of Spectrum Management subfield in the Capability
Information of Beacon, Probe Response, and Association Response frames.
Spectrum Management bit is set when directly requested by new
configuration option spectrum_mgmt_required=1 or when AP is running on
DFS channels. In the future, also TPC shall require this bit to be set.
Signed-hostap: Srinivasan <srinivasanb@posedge.com>
Signed-hostap: Chaitanya T K <chaitanyatk@posedge.com>
Signed-hostap: Marek Puzyniak <marek.puzyniak@tieto.com>
Add Power Constraint information element to Beacon and Probe Response
frames when hostapd is configured on 5 GHz band and Country information
element is also added. According to IEEE Std 802.11-2012 a STA shall
determine a local maximum transmit power for the current channel based
on information derived from Country and Power Constraint elements.
In order to add Power Constraint element ieee80211d option need to be
enabled and new local_pwr_constraint config option need to be set to
unsigned value in units of decibels. For now this value is statically
configured but the future goal is to implement dynamic TPC algorithm
to control local power constraint.
Signed-hostap: Srinivasan <srinivasanb@posedge.com>
Signed-hostap: Chaitanya T K <chaitanyatk@posedge.com>
Signed-hostap: Marek Puzyniak <marek.puzyniak@tieto.com>
This new mechanism allows P2P Client to request an IPv4 address from the
GO as part of the 4-way handshake to avoid use of DHCP exchange after
4-way handshake. If the new mechanism is used, the assigned IP address
is shown in the P2P-GROUP-STARTED event on the client side with
following new parameters: ip_addr, ip_mask, go_ip_addr. The assigned IP
address is included in the AP-STA-CONNECTED event on the GO side as a
new ip_addr parameter. The IP address is valid for the duration of the
association.
The IP address pool for this new mechanism is configured as global
wpa_supplicant configuration file parameters ip_addr_go, ip_addr_mask,
ip_addr_star, ip_addr_end. For example:
ip_addr_go=192.168.42.1
ip_addr_mask=255.255.255.0
ip_addr_start=192.168.42.2
ip_addr_end=192.168.42.100
DHCP mechanism is expected to be enabled at the same time to support P2P
Devices that do not use the new mechanism. The easiest way of managing
the IP addresses is by splitting the IP address range into two parts and
assign a separate range for wpa_supplicant and DHCP server.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
It is possible for the configuration to be temporarily invalid when
adding a new AP through SET commands followed by ENABLE. Avoid this
issue by using less strict validation on SET commands and perform full
configuration validation only on ENABLE. Use cases with configuration
file maintain their previous behavior, i.e., full validation after the
file has been read.
Signed-hostap: Jouni Malinen <j@w1.fi>
This debugging mechanism has now been deprecated by the control
interface commands that can be used to fetch same internal information
from hostapd in a more convenient way. Leave the empty USR1 signal
handler and configuration file parameter for backwards compatibility.
They can be removed in future versions of hostapd.
Signed-hostap: Jouni Malinen <j@w1.fi>
Add a parameter to send the overlapping BSS scan parameter
information element. This will require clients to perform
background scans to check for neigbors overlapping this
HT40 BSS. Since the implementation is incomplete it should
only be used for testing.
Signed-hostap: Paul Stewart <pstew@chromium.org>
The global control interface command "REMOVE <ifname>" can now be used
to remove a single virtual interface (BSS) without affecting other
virtual interfaces on the same radio.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This allows the configuration validation routines to be called from
src/ap/*.c for runtime updates of configuration without reprocessing the
full configuration file.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This makes it more convenient to move BSS configuration entries between
struct hostapd_config instances to clean up per-BSS configuration file
design.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This may be needed if the wpa_psk information for previously derived
from passphrase and either the SSID or the passphrase has changed.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The new bss_load_test parameter can be used to configure hostapd to
advertise a fixed BSS Load element in Beacon and Probe Response frames
for testing purposes. This functionality is disabled in the build by
default and can be enabled with CONFIG_TESTING_OPTIONS=y.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This allows QoS Map Set element to be added to (Re)Association Response
frames and in QoS Map Configure frame. The QoS Mapping parameters are
also made available for the driver interface.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
When using per-device PSKs, select the PSK based on the P2P Device
Address of the connecting client if that client is a P2P Device. This
allows the P2P Interface Address to be changed between P2P group
connections which may happen especially when using persistent groups.
Signed-hostap: Jouni Malinen <j@w1.fi>
This makes the P2P Device Address of the Enrollee available with the PSK
records to allow P2P Device Address instead of P2P Interface Address to
be used for finding the correct PSK.
Signed-hostap: Jouni Malinen <j@w1.fi>
"wpa_cli p2p_set per_sta_psk <0/1>" can now be used to disable/enable
use of per-device PSKs in P2P groups. This is disabled by default.
When enabled, a default passphrase is still generated by the GO for
legacy stations, but all P2P and non-P2P devices using WPS will get
a unique PSK.
This gives more protection for the P2P group by preventing clients from
being able to derive the unicast keys used by other clients. This is
also a step towards allowing specific clients to be removed from a group
reliably without having to tear down the full group to do so.
Signed-hostap: Jouni Malinen <j@w1.fi>
This adds ACS support to hostapd. Currently only survey-based
algorithm is available.
To use ACS you need to enable CONFIG_ACS=y in .config and use
channel=0 (or channel=acs_survey) in hostapd.conf.
For more details see wiki page [1] or comments in src/ap/acs.c.
[1]: http://wireless.kernel.org/en/users/Documentation/acs
Signed-hostap: Michal Kazior <michal.kazior@tieto.com>
In a AP/STA concurrent setup, if the STA interface is continually
scanning, trying to connect to a network, the AP interface
is basically broken since beaconing would be erratic.
This option can be used in a WDS setup where one AP acts as a
Client/AP-Repeater. The Repeater AP interface has to start beaconing
only after the Client interface has established a WDS link with the
"Root AP".
Signed-hostap: Sujith Manoharan <c_manoha@qca.qualcomm.com>
The new server_id parameter in hostapd.conf can now be used to specify
which identity is delivered to the EAP peer with EAP methods that
support authenticated server identity.
Signed-hostap: Jouni Malinen <j@w1.fi>
When using OpenSSL with TLS-based EAP methods, wpa_supplicant can now be
configured to use OCSP stapling (TLS certificate status request) with
ocsp=1 network block parameter. ocsp=2 can be used to require valid OCSP
response before connection is allowed to continue.
hostapd as EAP server can be configured to return cached OCSP response
using the new ocsp_stapling_response parameter and an external mechanism
for updating the response data (e.g., "openssl ocsp ..." command).
This allows wpa_supplicant to verify that the server certificate has not
been revoked as part of the EAP-TLS/PEAP/TTLS/FAST handshake before
actual data connection has been established (i.e., when a CRL could not
be fetched even if a distribution point were specified).
Signed-hostap: Jouni Malinen <j@w1.fi>
Currently, hostapd_get_vlan_id_ifname() is used to determine if a given
vlan is valid *and* to actually determine the interface. This leads to
wpa_set_keys() sometimes setting the key on the wildcard interface name,
which does not make sense.
This patch therefore adds hostapd_vlan_id_valid() and makes
hostapd_get_vlan_id_ifname() not return a wildcard interface.
Signed-hostap: Michael Braun <michael-dev@fami-braun.de>
Currently, when different BSS using different tagged vlan
interfaces, they are forced to share the bridge brvlan#,
which is not desirable.
This patch fixes this by making the bridge name configurable.
Signed-hostap: Michael Braun <michael-dev@fami-braun.de>
This patch is based on the original work by Boris Presman and
Victor Goldenshtein. Channel Switch Announcement support has been
removed and event handling as well as channel set handling was
changed, among various other changes.
Cc: Boris Presman <boris.presman@ti.com>
Cc: Victor Goldenshtein <victorg@ti.com>
Signed-hostap: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
