Sending a wowlan configuration command can be done on any wireless
interface (not only netdev), as it is a device configuration and not
interface configuration specific. Fix the code to allow it to be
sent on any interface.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Android libnl_2 implementation added support for "nl80211" name in
commit 'libnl_2: Extend genl_ctrl_resolve() to support "nl80211" name'
in July 2012 which got included in Android 4.2. It is fine to drop this
old Android ICS workaround from wpa_supplicant now.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Change send_mlme() API to allow sending management frames on a specific
channel, overriding the internal driver decision.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
When device supports dual band operations with offloaded ACS, hw_mode
can now be set to any band (hw_mode=any) in order to allow ACS to select
the best channel from any band. After a channel is selected, the hw_mode
is updated for hostapd.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
It was possible for the WPA_ALG_PMK algorithm in set_key() to result in
trying to configure a key with cipher suite 0. While this results in a
failure from cfg80211 or driver, this is not really desirable operation,
so add a check for cipher suite conversion result before issuing the
nl80211 command.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
By analysing objdump output some read only structures were found in
.data section. To help compiler further optimize code declare these
as const.
Signed-off-by: Mikael Kanstrup <mikael.kanstrup@sonymobile.com>
Previously, only P2P and mesh use cases enforced unique MAC address for
a dynamically added virtual interface. Extend this to cover normal
station mode interfaces since those can now be added with INTERFACE_ADD.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Previous workaround for WEXT events from the Host AP driver required
wlan# and wifi# interfaces to have fixed names with the same number.
While that used to be the common case ten years ago, it is less common
nowadays. Extend this to use sysfs (if available) to figure out the
wifi# interface name if the specified interface is detected to be using
the Host AP driver.
Signed-off-by: Jouni Malinen <j@w1.fi>
This extends NL80211_CMD_ROAM event processing to allow the driver to
roam to another ESS (different SSID) when using offloaded BSS selection.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Update ACS driver offload feature for VHT configuration. In addition,
this allows the chanlist parameter to be used to specify which channels
are included as options for the offloaded ACS case.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
In wiphy_info_handler(), vendor specific commands were
interpreted as QCA specific without checking for the OUI,
which caused incorrect setting of driver flags with
commands from other vendors. As a result, that could
prevent proper operation (e.g., inability to process CSA).
This patch ensures that QCA vendor specific commands are
checked against QCA OUI before related flags are set.
Signed-off-by: Zefir Kurtisi <zefir.kurtisi@neratec.com>
Handle NL80211_ATTR_EXT_FEATURES attribute and
NL80211_EXT_FEATURE_VHT_IBSS to determine whether
the driver supports VHT with IBSS.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
ML80211_ATTR_TDLS_OPERATION can now set to NL80211_TDLS_DISCOVERY_REQ to
allow the driver to request wpa_supplicant to initiate TDLS Discovery
Request.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This extends the TDLS operation request mechanism to allow TDLS
Discovery Request to be initiated by the driver similarly to the
existing Setup and Teardown requests.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The initial IEEE 802.11 ProxyARP functionality in the kernel needed
changes in behavior and that ended up requiring an independent
configuration parameter to be used. Update hostapd to use that new
proxyarp_wifi parameter instead of the earlier proxyarp.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This converts the QCA vendor event to EVENT_DFS_* events for the case
of DFS offloaded to the driver.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This allows wpa_supplicant to recover from some of the cases where
cfg80211 is unloaded and reloaded without restarting wpa_supplicant. The
netlink socket used for nl80211 events (global->nl_event) seemed to end
up in otherwise functionality state, but with all the event memberships
lost when cfg80211 gets reloaded.
There does not seem to be any clear way of determining when this has
happened, so it looks simplest to just try to re-subscribe to all the
events whenever an interface is re-enabled or added.
Signed-off-by: Jouni Malinen <j@w1.fi>
This modifies the BSS selection routines to calculate SNR and estimated
throughput for each scan result and then use the estimated throughput as
a criteria for sorting the results. This extends the earlier design by
taking into account higher throughput rates if both the AP and local
device supports HT20, HT40, or VHT80. In addition, the maximum rate is
restricted based on SNR.
In practice, this gives significantly higher probability of selecting
HT/VHT APs when there are multiple BSSes in the same ESS and SNR is not
low enough to prevent higher MCS use.
Signed-off-by: Jouni Malinen <j@w1.fi>
Configure the GO CTWindow on APstart if the driver supports it and this
parameter is set in wpa_supplicant configuration.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Read p2p_go_ctwindow (0-127 TUs) from the config file, and pass it to
the driver on GO start.
Use p2p_go_ctwindow=0 (no CTWindow) by default.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Add fixed_freq=<0/1> network block parameter and pass it to the driver
when starting or joining an IBSS. If this flag is set, IBSS should not
try to look for other IBSS networks to merge with on different channels.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
The '/usr/include/libnl3' header path is unsafe for cross-compilation.
Use pkg-config to find libnl-3.0 headers by default and alternatively,
allow LIBNL_INC=<path> to be used in .config to override.
Signed-off-by: Romain Naour <romain.naour@openwide.fr>
When DFS offloading capability is supported by the driver, the driver
should use these events to indicate when a radar pattern has been
detected, channel availability check (CAC) has been completed, aborted
or finished after the non-occupancy period is over on a DFS channel.
Also, add a new driver.h event to be used by NL80211 to indicate CAC
Started event on a DFS channel.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
RTM_NEWLINK event without IFF_UP were processed for all related
interfaces (including VLANs and bridge). While these events may need to
be processed for other purposes, they should not end up claiming that
the main interface has been disabled, so indicate
EVENT_INTERFACE_DISABLED only if the ifname matches the first BSS ifname
for the interface. In addition, fix some of the ifup/down checks from
if_indextoname() cases to actually use the resolved ifname (namebuf)
rather than hardcoding the first configured ifname to be used.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This is a step towards enabling hostapd to restart AP mode functionality
if the interface is disabled and re-enabled, e.g., with ifconfig down
and up. This commit takes care of beaconining only which may be
sufficient for open mode connection, but not for WPA2 cases.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This adds testing code (for CONFIG_TESTING_OPTIONS=y builds only) to
send an nl80211 vendor command and report a test vendor event in case
the driver supports this.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Commit 5a2a6de6a5 ('mesh: Make inactivity
timer configurable') has a problem on 32 bit systems. Setting
NL80211_MESHCONF_PLINK_TIMEOUT to 0xffffffff causes expiration of STA in
a minute by NL80211_CMD_DEL_STATION event. this is the kernel rule for
STA expiration:
(current jiffies) > (frame Rx jiffies + NL80211_MESHCONF_PLINK_TIMEOUT * 250)
On a 32 bit system, the right side could overflow and be unexpected
small value if NL80211_MESHCONF_PLINK_TIMEOUT is sufficiently large. STA
expiration occurs by this reason.
This patch solves the problem by disabling the STA expiration
functionality in mac80211. However, old kernel does not support
disabling it. If so, this patch sets mac80211 inactivity timer 60
seconds into future from the wpa_supplicant inactivity timer.
And I mis-understood that mesh_max_inactivity=0 disables inactivity
timer in wpa_supplicant. This commit fixes it also.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
Commit 630b3230c8 ('nl80211: Increase
netlink receive buffer size') added unconditional use of
nl_socket_set_buffer_size() which was not included in libnl 1.1. Fix use
of that old version by making this conditional on CONFIG_LIBNL20.
Signed-off-by: Jouni Malinen <j@w1.fi>
This modifies struct wpa_ptk to allow the length of KCK and KEK to be
stored. This is needed to allow longer keys to be used, e.g., with
Suite B 192-bit level.
Signed-off-by: Jouni Malinen <j@w1.fi>
The correct nl80211 flag for group key management cipher was set only
for BIP (AES-CMAC-128). The same flag needs to be used with the newer
ciphers BIP-CMAC-256, BIP-GMAC-128, and BIP-GMAC-256.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
libnl uses a pretty small buffer (32 kB that gets converted to 64 kB) by
default. It is possible to hit that limit in some cases where operations
are blocked, e.g., with a burst of Deauthentication frames to hostapd
and STA entry deletion. Try to increase the buffer to make this less
likely to occur.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
We were copying the NL80211_ATTR_EXT_CAPA attribute into the
extended_capa_mask element, which is incorrect. Use
NL80211_ATTR_EXT_CAPA_MASK instead.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Current mesh code uses ap_max_inactivity as inactivity timer. This patch
makes it configurable.
There is another mesh inactivity timer in mac80211. The timer works even
if user_mpm=1. So this patch sets the max value to the timer for
workaround.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
If the inactivity check returns that there is no entry remaining for the
STA in the kernel, drop the STA in hostapd as well.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
If a second scan trigger attempt fails in STA mode, the error path was
supposed to restore the old mode that was in use before changing to STA
mode. However, wpa_driver_nl80211_set_mode() changes drv->nlmode on
success, so the recovery path needs to use the saved old_mode value
instead.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add WPA_DRIVER_FLAGS_HT_IBSS driver feature flag. Some drivers could not
set this feature and next could fail when we will enable HT support for
IBSS with error message: nl80211: Join IBSS failed: ret=-22 (Invalid
argument).
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
On FreeBSD and DragonFly BSD, we additionally need to skip the
isr_meshid_len bytes of the MESH ID, to get the correct address for
copying the IE data.
The isr_meshid_len field was added in the FreeBSD svn revision r195618
in 2009, so I don't think we need to check the FreeBSD version here.
Signed-off-by: Imre Vadász <imre@vdsz.com>
Unfortunately, libnl 3.0 has changed the API in a way that is not
backwards compatible by renaming nlmsg_len() to nlmsg_datalen() without
leaving the older nlmsg_len() defined. As such, there does not seem to
be any clean way of using this function without breaking the build with
some libnl versions. For now, replace this call with direct calculation
of the data length since it can be done with a simple one-liner that
compiles with all libnl versions.
Signed-off-by: Jouni Malinen <j@w1.fi>
These are practically unreachable code since cfg80211 fills in the
required attributes or does not send the event. Keep the checks in
place, but minimize the extra code in wpa_supplicant/hostapd.
Signed-off-by: Jouni Malinen <j@w1.fi>
cfg80211 dropped support for tracking BSS authentication state and
setting NL80211_BSS_STATUS_AUTHENTICATED in 'cfg80211: stop tracking
authenticated state' three years ago (starting in Linux 3.4). As such,
this workaround code in wpa_supplicant cannot be reached anymore. There
is no real need for maintaining it for older kernels either, since there
are other ways of detecting and working around state mismatches with the
actual authentication operations failing.
Signed-off-by: Jouni Malinen <j@w1.fi>
While there is no explicit driver capability advertisement for this in
nl80211, the EOPNOTSUPP response can be interpreted as a clear
indication of NL80211_CMD_SET_REKEY_OFFLOAD not being supported. Check
for that and don't try to offload keys again if the driver has not use
for them.
Signed-off-by: Jouni Malinen <j@w1.fi>
1. Add parameters to the scan command to allow MAC address
randomization during scan and scheduled scan.
2. Add capability bits to publish MAC address randomization support
in scan and scheduled scan.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
The kernel-driver/firmware are responsible for performing periodic
switches to the target channel with the given peer. Propagate all TDLS
channel switching related information to kernel.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
The supplicant code does not try to control the actual channel of the
radio at any point. It simply passes the target peer and channel
parameters to the driver. It's the driver's responsibility to
periodically initiate TDLS channel-switch operations when TDLS
channel-switching is enabled.
Allow enable/disable operations to be invoked via the control interface.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
If registering WMM-AC ADDTS response action frame or WMM-AC DELTS
action frame fails, the management frame handler is not being
registered. This results with a segmentation fault when trying to
unsubscribe the handler when the interface is removed.
Fix it by always registering the handler and just returning a negative
value to note that the action frame could not be registered.
This fixes an issue introduced in the commit
dfa8787833 ('nl80211: Implement
add_ts/del_ts ops').
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
This reduces the time possible keys could remain in heap memory. Couple
of the nl80211 messages include keys (TK for normal ciphers and
KCK/KEK/PMK for various offloading cases).
Signed-off-by: Jouni Malinen <j@w1.fi>
There was one final remaining linux_set_iface_flags() call that did not
check the result. This specific one does not really matter much, but
anyway, be more consistent by checking the result and log any error in
debug log. (CID 74146)
Signed-off-by: Jouni Malinen <j@w1.fi>
This converts most of the remaining perror() and printf() calls from
hostapd and wpa_supplicant to use wpa_printf().
Signed-off-by: Jouni Malinen <j@w1.fi>
struct wpa_driver_associate_params moved to using struct
hostapd_freq_params instead of just frequency. Need to update wpa_priv
to do same.
Signed-off-by: Jouni Malinen <j@w1.fi>
It would be at least theoretically possible for the bridge netdev to
have disappeared at the time hostapd processes the RTM newlink/dellink
message. As such, it is better to verify that if_indextoname() actually
returned success before printing the bridge ifname in debug. In
addition, there is not much point trying to add the bridge ifindex into
the list of own ifindexes in case the interface has already been
removed, so skip that part as well.
Signed-off-by: Jouni Malinen <j@w1.fi>
This was used in the past, but all the event processing is now either
through process_global_event() or process_bss_event().
Signed-off-by: Jouni Malinen <j@w1.fi>
Maximum number of peer links is maximum number of connecting mesh peers
at the same time. This value is 0..255 based on the
dot11MeshNumberOfPeerings range.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
The local ifindex list needs to be updated only if the current bridge
interface is the correct one. If hostapd is going to move the interface
to another bridge, the old bridge ifindex must not be added. In
addition, when removing the bridge interface on deinit, it may need to
be set down to allow bridge removal.
Signed-off-by: Jouni Malinen <j@w1.fi>
The interface was incorrectly changed to station mode between the two
IBSS join requests and that made the second attempt fail. Remove that
undesired mode clearing from this special case of IBSS leave sequence.
Signed-off-by: Jouni Malinen <j@w1.fi>
Commit 9f12614b8c ('nl80211: Do not
encrypt IEEE 802.1X WEP EAPOL') tried to use
NL80211_ATTR_CONTROL_PORT_NO_ENCRYPT to disable encryption of EAPOL
frames for WEP IEEE 802.1X. However, it used incorrect key management
suite (IEEE 802.1X with WPA/WPA2 while the non-WPA version is needed
here). Consequently, the no-encrypt flag was never set to the driver
(WPA/WPA2 cases do not meet the WEP as pairwise criteria).
Signed-off-by: Jouni Malinen <j@w1.fi>
The mesh gate is used to bridge (or route) between mesh network and
another network. For example, mesh gate acts as router between mesh
network and IEEE 802.11 BSS network.
This command makes a virtual mesh interface to be used for mesh gate.
This command expects to be used like this.
wpa_cli -i wlan0 MESH_INTERFACE_ADD ifname=mesh0
wpa_cli -i mesh0 add_network
wpa_cli -i mesh0 set_network 0 ssid '"commell_2X_mmm"'
wpa_cli -i mesh0 set_network 0 mode 5
wpa_cli -i mesh0 set_network 0 frequency 2412
wpa_cli -i mesh0 set_network 0 key_mgmt SAE
wpa_cli -i mesh0 set_network 0 psk '"01234567"'
wpa_cli -i mesh0 mesh_group_add 0
wpa_cli -i wlan0 mesh_group_remove mesh0
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
Building wpa_supplicant with the musl C library fails since musl does
not define type names such as '__uint32_t'. To support building
wpa_supplicant with the musl C library use the integer types declared in
the ISO C standard header file <stdint.h>.
Signed-off-by: Jörg Krause <jkrause@posteo.de>
drv->ctx always points to the first BSS and we should report event using
BSS related to the interface we got NL80211_CMD_NEW_STATION from.
This fixes STA association for drivers using NL80211_CMD_NEW_STATION and
multiple virtual interfaces.
Before:
nl80211: Drv Event 19 (NL80211_CMD_NEW_STATION) received for wlan0-1 (ifindex:7)
nl80211: New station 02:00:00:00:01:00
wlan0: STA 02:00:00:00:01:00 IEEE 802.11: associated
After:
nl80211: Drv Event 19 (NL80211_CMD_NEW_STATION) received for wlan0-1 (ifindex:7)
nl80211: New station 02:00:00:00:01:00
wlan0-1: STA 02:00:00:00:01:00 IEEE 802.11: associated
This is not applicable to the cases where authentication (AP SME & MLME)
is in hostapd and hostapd_assoc_cb() instead of hostapd_notif_assoc()
handles BSS selection.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
The send_eapol() callback was used by driver_test.c, but with that
removed, there is no remaining users of the alternative EAPOL frame
transmitting mechanism in wpa_supplicant, i.e., all remaining driver
interfaces use l2_packet instead. Remove the send_eapol() to get rid of
unused code.
Signed-off-by: Jouni Malinen <j@w1.fi>
This commit introduces a QCA vendor command that allows interrogation of
the vendor-specific features supported by the device/driver. Currently
the only defined feature is the ability to offload key management.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
It is possible for unmasking of 11b rates to fail if a P2P group is
terminated while the netdev is down (e.g., due to rfkill block). This
could result in the 11b TX rates being left masked for non-P2P
operations. This would be particularly unfortunate for channel 14 use
since OFDM rates are not allowed on channel 14 and only OFDM rates were
configured P2P. This issue showed up, e.g., when running hwsim test case
rfkill_autogo followed by ap_wps_conf_chan14.
It may be possible to allow the failed operation in cfg80211/mac80211,
but it looks better to work around this on wpa_supplicant side as well.
Try to unmask the 11b rates again on the next connection request if the
rate unmasking operation had failed.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This makes it easier to debug issues related to TX rate masking for P2P
use cases (and unmasking for non-P2P).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This converts os_snprintf() result validation cases to use
os_snprintf_error() in cases where success condition was used to execute
a step. These changes were done automatically with spatch using the
following semantic patch:
@@
expression E1,E2,E3;
statement S1;
@@
E1 = os_snprintf(E2, E3, ...);
- if (\( E1 >= 0 \| E1 > 0 \) && \( (size_t) E1 < E3 \| E1 < (int) E3 \| E1 < E3 \))
+ if (!os_snprintf_error(E3, E1))
S1
Signed-off-by: Jouni Malinen <j@w1.fi>
This adds verification of os_snprintf() result against the maximum
buffer length. These changes were done automatically with spatch
using the following semantic patch:
@@
expression E1,E2,E3;
statement S1;
@@
E1 = os_snprintf(E2, E3, ...);
- if (\( E1 < 0 \| E1 <= 0 \))
+ if (os_snprintf_error(E3, E1))
(
S1
|
{ ... }
)
Signed-off-by: Jouni Malinen <j@w1.fi>
This reduced number of unnecessarily duplicated driver interface
callback functions for sending Action frames by using the more generic
send_action() instead of FT specific send_ft_action().
Signed-off-by: Jouni Malinen <j@w1.fi>
This helper function had not used the nl80211_set_iface_id() helper, but
there is no reason why it couldn't re-use the same helper as other
places using nl80211_cmd_msg().
Signed-off-by: Jouni Malinen <j@w1.fi>
Use the helper function to replace places that use nlmsg_alloc(),
nl80211_cmd(), and either bss->ifindex or if_nametoindex(bss->ifname).
Signed-off-by: Jouni Malinen <j@w1.fi>
bss->wdev_id_set is set for the non-detdev P2P Device, so
nl80211_cmd_msg() can be used as-is for these cases as well.
Signed-off-by: Jouni Malinen <j@w1.fi>
