The new max_oper_chwidth and freq2 arguments to P2P_CONNECT, P2P_INVITE,
and P2P_GROUP_ADD control interface commands can be used to request
larger VHT operating channel bandwidth to be used than the previously
used maximum 80 MHz.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This extends the previous design that covered only the VHT 80 MHz cases
for VHT channel flags. New functions are introduced to allow 160 MHz
bandwidth cases to determine the center channel and check availability
of a 160 MHz channel.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This adds definitions for the global operating classes 129 and 130 for
VHT 80+80 MHz and 160 MHz use cases.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Previously, MB IEs were parsed only from association event. Try to get
MB IEs from other management frames like Probe Response frames. The MB
IEs from the association event may not be up-to-date and in some cases
may actually be missing and updating the information based on other
frames can improve robustness of FST exchanges.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Modify the FST peer connection check so it won't skip peers without MB
IEs making it more permissive for peers that didn't provide MB IEs
during association request. This can be helpful, e.g., in cases where a
STA's interface connected before it was added to the FST group. This
allows the AP to receive FST Action frames and initiate session with a
STA via STA's interface that doesn't expose MB IEs.
The adjusted FST protocol is still safe, as it protects itself in many
other ways (checking band info and it's accordance to the interfaces,
Setup IDs, connection states of the interfaces involved, etc.)
effectively avoiding all types of invalid situations.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
There was only a single file remaining in this directory. All the other
old test functionality has been moved under the top level tests
directory. Move the remaining file to the wpa_supplicant directory to
get rid of the subdirectory.
Signed-off-by: Jouni Malinen <j@w1.fi>
The old wpa_supplicant/Makefile target test-eap_sim_common did not work
anymore and anyway, this test is better placed in the newer hwsim
framework to make sure the test case gets executed automatically.
Signed-off-by: Jouni Malinen <j@w1.fi>
These wpa_supplicant test programs have not been maintained for years
and it would take significant effort to get these into working state.
Since there does not seem to be any real need for these based on lack of
maintenance, it is easier to just drop these tools for now.
Signed-off-by: Jouni Malinen <j@w1.fi>
Number of places were calling functions that are not included in
CONFIG_NO_WPA=y build anymore. Comment out such calls. In addition, pull
in SHA1 and MD5 for config_internal.c, if needed.
Signed-off-by: Jouni Malinen <j@w1.fi>
This syncs the test cases with the implementation change in station's MB
IE creation. FST tests should expect MB IE regardless of the station
connection state and whether the current connection is FST-enabled or
not. This fixes the follow test cases that started reporting failures
with the previous commit change in src/fst/fst_group.c:
fst_disconnect_1_of_2_stas_from_non_fst_ap
fst_sta_connect_to_non_fst_ap
fst_second_sta_connect_to_non_fst_ap
fst_disconnect_2_of_2_stas_from_non_fst_ap
fst_second_sta_connect_to_fst_ap
fst_disconnect_1_of_2_stas_from_fst_ap
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
FST STA should always expose its MB IEs regardless of its connection
state and whether the connected AP is currently FST-enabled or not.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add a test to verify that a P2P GO does not start a CSA
once invitation signalling is done, and the P2P client is
about to connect.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
When an invitation to join an existing group is accepted by the
peer device, set p2p_go_wait_client to the current time so
that wpas_p2p_in_progress() would return != 0, thus preventing
P2P CSA, scanning etc., that would interfere with the peer
device connection.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
This test case was failing if a PropertiesChanged signal for P2P peer
gets delivered from a previous test case. Avoid that by waiting for the
new group to be formed before processing any PropertiesChanged signals.
This failure was triggered by the following test case sequence:
dbus_p2p_two_groups dbus_p2p_group_idle_timeout
Signed-off-by: Jouni Malinen <j@w1.fi>
When built with browser-android.c, hs20-osu-client used to always launch
the native/stock Android browser for OSU user interaction. This browser
is not present in all devices. It is better to give the option to the
user to select his/her browser.
Here the user will be shown a pop up to select the browser that he/she
wants.
Signed-off-by: Somdas Bandyopadhyay <somdas.bandyopadhyay@intel.com>
It looks like a previous P2P test case can cause the initial single
channel scan in ap_open_select_twice take more than five seconds in some
cases. While that is not really expected behavior, this test case should
not fail. Increase the timeout to avoid reporting false failures here.
This could be triggered with the following test case sequence:
p2p_msg_unexpected_go_neg_resp ap_open_select_twice
Signed-off-by: Jouni Malinen <j@w1.fi>
Some drivers do not support having two station interfaces, so the fact
that wpa_supplicant always creates a new interface in station mode, even
if it will be used as another type of interface, may prevent
wpa_supplicant from creating new interfaces. Allow setting the interface
type when a new interface is created so that interfaces of supported
types can be created.
Currently supported types are station ("sta") and AP ("ap"). If the
interface type is not specified, a station interface will be created.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
When an AP interface it created, it is also setup and subscribes
for management frames etc. However, when the interface is added by
wpa_supplicant, setting up for AP operations is redundant because
it will be done by wpa_supplicant on wpa_drv_init() when setting
the interface mode to AP.
In addition, it may cause wpa_supplicant to fail initializing the
interface as it will try to subscribe for management frames on this
interface but the interface is already registered.
Change this, so when adding an AP interface, make setting up the AP
optional, and use it only when the interface is added by hostapd but not
when it is added by wpa_supplicant.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
LibreSSL does not yet support the new API, so do not use it
when LIBRESSL_VERSION_NUMBER macro is defined.
Signed-off-by: Marek Behun <kabel@blackhole.sk>
These test cases depend on the HT40 co-ex scans not swapping PRI/SEC
channels. It was possible for a test case to fail, e.g., in the
following sequence: ap_ht40_5ghz_match ap_vht80b.
Signed-off-by: Jouni Malinen <j@w1.fi>
When clearing pending TX action to start a new P2P operation like
P2P_FIND or P2P_LISTEN, wpas_p2p_action_tx_clear() was used to clear
the send action work. However, in cases where the action work has wait
time, it is not cleared immediately but only after the wait time ends.
This may cause delay in starting the P2P operation.
Fix that by always clearing the send action work immediately on these
P2P commands that result in immediate P2P state change and practically
stopping a previous operation, if one was pending.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
When an AP is started on the 5.2 GHz band with 40 MHz bandwidth, a
scan is issued in order to handle 20/40 MHz coexistence. However,
the scan is issued even if iface->conf->no_pri_sec_switch is set,
which is redundant.
Fix this by checking iface->conf->no_pri_sec_switch before starting
the scan.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
The de-authentication flow in wpa_driver_nl80211_deauthenticate() can
result in a locally generated de-authentication event. To avoid getting
this extra event ignore_next_local_deauth flag is set, and should be
cleared when the next local deauth event is received. However, it is not
cleared when the event shows up after the wpa_supplicant has started a
connection with a new AP, and as a result it might ignore future
deauth event from the driver.
Fix this by clearing the flag if the event is locally generated.
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
The authentication flow in wpa_driver_nl80211_authenticate() can
result in a locally generated de-authentication, in which both
next_local_deauth and ignore_next_local_deauth are set.
However, in mlme_event_deauth_disassoc(), when ignore_deauth_event is
set, the flag is cleared, but the flow immediately returns leaving
ignore_next_local_deauth set, which can result in ignoring future deauth
event from the driver, leaving the wpa_supplicant in an inconsistent
state.
Fix this by clearing both flags in case that next_local_deauth is set.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
This allows offloaded roaming to inform user space of the change in IP
subnet post roaming. The device may have roamed to a network which is in
a different subnet which will result in IP connectivity loss. Indicating
the change in subnet enables the user space to refresh the IP address or
to perform IP subnet validation if unknown status is indicated.
The driver indication is reported with a new event from wpa_supplicant
in the following format:
CTRL-EVENT-SUBNET-STATUS-UPDATE status=<0/1/2>
where
0 = unknown
1 = IP subnet unchanged (can continue to use the old IP address)
2 = IP subnet changed (need to get a new IP address)
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This verifies that the second SELECT_NETWORK for the same network starts
a new scan immediately if the previous connection attempt is waiting for
the next scan iteration to start.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Commit 2a6f78fbbe ('Do not re-associate on
SELECT_NETWORK to current network') started skipping all SELECT_NETWORK
connection steps if the selected network had already been selected
previously. This happened regardless of whether the connection was
already established. This is not necessarily desirable for all cases
where there is no immediate action to even try to connect (e.g., long
wait for the next scan).
Speed this up by allowing the SELECT_NETWORK operation to get started if
there is no connection or ongoing connection attempt with the selected
network.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The EAP peer state machine moved from IDLE to FAILURE state when the
EAPOL Authenticator triggered reauthentication with an
EAP-Request/Identity in a case where the associated started with FT
protocol or offloaded PMKSA cache use (4-way handshake using a
previously acquired PMK). This happened due to the altSuccess=TRUE
setting being left behind and not cleared when processing the restart of
authentication. Fix this by clearing altAccept and eapSuccess when going
through SUPP_PAE RESTART state.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The EAPOL AUTH_PAE state machine was left in incomplete state at the
completion of FT protocol. Set portValid = TRUE to allow the state
machine to proceed from AUTHENTICATING to AUTHENTICATED state, so that a
new EAPOL reauthentication can be triggered.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This avoids issues with following test cases failing due to unexpected
starting state. This issue showed up with the following hwsim test case
sequence:
fst_setup_mbie_diff fst_dynamic_iface_attach
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Mesh Points themselves have capability to support VHT as long as
hardware supports it. However, supporting VHT in mesh mode was disabled
because no one had clearly tested and confirmed its functionality. Since
VHT80 has now been verified to work with ath10k QCA988X driver and
mac80211_hwsim, enable VHT support in mesh mode.
Signed-off-by: Peter Oh <poh@qca.qualcomm.com>
Set WLAN_STA_WMM flag to Mesh STA by default since Mesh STAs are QoS
STAs. Mesh STA's HT capabilities won't be parsed properly without the
flag.
Signed-off-by: Peter Oh <poh@qca.qualcomm.com>
It was possible for the WPS PBC state to get cached through to the
following test cases and that would trigger false failures. Fix this by
explicitly clearing the scan cache at the end of ap_wps_per_station_psk.
This issue was triggered with the following test case sequence:
ap_wps_per_station_psk autogo_pbc
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
If a memory allocation fails while parsing driver capabilities, drop all
mode/channel/rate information instead of returning possibly partial
information.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This is needed since the forced OOM may have forced the cached
information to be invalid or dropped. This issue was hit with the
following hwsim test case sequence:
ap_interworking_scan_filtering fst_sta_config_llt_large dbus_connect_oom
wpas_ctrl_enable_disable_network
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
If "STA_AUTOCONNECT 0" has been used to disable automatic connection on
disconnection event and the driver indicates a failure for the data
connection after successful WPS handshake, it is possible to hit a case
where wpa_s->disconnected is set to 1 and further attempts to connect
shall stop.
While "STA_AUTOCONNECT 0" is used to disable automatic reconnection
attempts in general, this specific WPS case can benefit from trying
again even with that configuration for a short period of time. Extend
the wpa_supplicant re-enable-networks-after-WPS 10 second timeout to
apply for ignoring disabled STA_AUTOCONNECT immediately after a WPS
provisioning step.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
