3GPP TS 24.232 Annex A.3 allows network operator to advertise only two
digits of MNC even if MNC has three digits. Allow such matches in
network selection. In addition, allow three digit matches of MNC even if
MNC length was assumed to be two to avoid missing networks if MNC length
cannot be determined reliably. Remove the '-' separator from simulated
SIM/USIM cases to allow the new matching rules to work.
Fix the PLMN List information element parsing loop to use the length of
the PLMN List instead of the length of the full 3GPP Cellular Info to
avoid unexpected matches should a new element ever be added by 3GPP.
Finally, add more debug prints from PLMN matching to make the logs
easier to understand.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
wpas_clear_wps() was just clearing the current wpa_s->current_ssid
pointer when removing a WPS network block which with the device was
associated. This could leave the association up even though the network
block had already been removed. Prevent this by explicitly disconnecting
from the network instead of such clearing current_ssid.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The new server_id parameter in hostapd.conf can now be used to specify
which identity is delivered to the EAP peer with EAP methods that
support authenticated server identity.
Signed-hostap: Jouni Malinen <j@w1.fi>
This allows more consistent interface to be used regardless of which
P2P driver design is used (especially for P2P management operations
over netdev vs. dedicated P2P_DEVICE).
Signed-hostap: Jouni Malinen <j@w1.fi>
Adding a new wpa_supplicant control interface for the dedicated
P2P_DEVICE would be quite confusing for programs that manage P2P
operations. Remove this control interface and require the global control
interface to be used since it will provide consistent interface for both
the new dedicated P2P_DEVICE (non-netdev) and old style P2P management
through a netdev.
Signed-hostap: Jouni Malinen <j@w1.fi>
Commit c68f6200a7 made these calls
conditional on !p2p_mgmt, but forced p2p_mgmt=1 for cases where the
driver does not use the dedicated P2P Device. Fix this by making the
!p2p_mgmt condition apply only if the driver does indicate use of a
dedicated P2P Device.
Signed-hostap: Jouni Malinen <j@w1.fi>
Check that SSL_clear_options and SSL_CTX_clear_options are defined
before using them to avoid compilation failures with older OpenSSL
versions that did not include these macros.
Signed-hostap: Jouni Malinen <j@w1.fi>
The interface name for the P2P group interface is derived from the
P2P management interface. When the P2P management interface is a
P2P Device interface, i.e., p2p-dev-wlanX, the name for the group
interface is abbreviated to p2p-X (X being group index). When the
P2P management interface starts with p2p-dev- use its postfix
instead. So P2P management interface p2p-dev-wlan3 results in group
interface name p2p-wlan3-0.
Signed-hostap: Arend van Spriel <arend@broadcom.com>
If the capability flag of the driver indicates a dedicated P2P Device is
supported, a P2P Device interface is created.
Create the P2P Device in main interface creation loop when the added
interface flags support and P2P supplicant is not yet initialized
avoiding recursion of add_interface.
Do not register l2_packet for P2P Device interface (both for EAPOL and
for TDLS).
Signed-hostap: Arend van Spriel <arend@broadcom.com>
Since the P2P_DEVICE support indication was added to kernel before
everything was working properly, there may be kernel versions in use
with the new mechanism breaking P2P functionality (especially with
mac80211_hwsim). For now, disable P2P_DEVICE support by default and
allow it to be enabled with driver_param=p2p_device=1 in the
configuration file. This default behavior may be changed in the future
once the kernel issues has been resolved in stable releases.
Signed-hostap: Jouni Malinen <j@w1.fi>
Setting p2p_no_group_iface means 'use P2P management interface as P2P
connection interface' because it attempts to change the interface type.
The P2P_DEVICE is a dedicated interface and can not be changed. As such
ignore the configuration option.
Signed-hostap: Arend van Spriel <arend@broadcom.com>
Another function that needs the wdev id when P2P management is done
using the P2P_DEVICE interface.
Signed-hostap: Arend van Spriel <arend@broadcom.com>
With P2P Device support there will be two interfaces with their
own MAC address. The P2P Interface Address must be unique so verify
it is.
Signed-hostap: Arend van Spriel <arend@broadcom.com>
The phy name was determined using /sys/class/net/<ifname> but the P2P
Device is not listed there since it does not have an associated net
device. This patch changes name determination to obtain the name from
the wiphy information provide by nl80211.
Signed-hostap: Arend van Spriel <arend@broadcom.com>
For P2P Device the netlink message should have wdev identifier
instead of the interface index. This fixes a failure which occurred
executing the P2P_GROUP_ADD command.
Signed-hostap: Arend van Spriel <arend@broadcom.com>
When using OpenSSL with TLS-based EAP methods, wpa_supplicant can now be
configured to use OCSP stapling (TLS certificate status request) with
ocsp=1 network block parameter. ocsp=2 can be used to require valid OCSP
response before connection is allowed to continue.
hostapd as EAP server can be configured to return cached OCSP response
using the new ocsp_stapling_response parameter and an external mechanism
for updating the response data (e.g., "openssl ocsp ..." command).
This allows wpa_supplicant to verify that the server certificate has not
been revoked as part of the EAP-TLS/PEAP/TTLS/FAST handshake before
actual data connection has been established (i.e., when a CRL could not
be fetched even if a distribution point were specified).
Signed-hostap: Jouni Malinen <j@w1.fi>
In wpa_supplicant_deinit(), the function wpas_p2p_deinit_global()
was called. Remove it as it will be called from wpas_deinit_iface()
upon removal of the P2P management interface.
Signed-hostap: Arend van Spriel <arend@broadcom.com>
When P2P Device is used as P2P management interface the creation of the
P2P group interface fails because MAC address retrieval fails for the
P2P Device interface.
Signed-hostap: Arend van Spriel <arend@broadcom.com>
For P2P an interface may be created for the P2P client/group. The
create request is done on the P2P management interface, which may
be a P2P Device interface. In that case it needs to use the wdev_id.
Signed-hostap: Arend van Spriel <arend@broadcom.com>
In order to get a P2P-DEVICE-FOUND event the supplicant needs to
see a peer device during SEARCH and LISTEN phase. The SEARCH
phase does a scan so obtaining the scan results for the P2P Device
interface needs to be supported, i.e., use the wdev_id.
Signed-hostap: Arend van Spriel <arend@broadcom.com>
For P2P Device the MAC address is determined upon .init2(). The
wpa_s for this interface retrieves this address in
wpa_supplicant_update_mac_addr() using the .get_mac_addr() callback.
Signed-hostap: Arend van Spriel <arend@broadcom.com>
The function setting the interface mode also handles management
frame subscription. Rework it so subscription is done for the
P2P Device interface.
Signed-hostap: Arend van Spriel <arend@broadcom.com>
The driver uses linux_set_iface_flags() in several places. Introduce and
use i802_set_iface_flags() which also works for P2P Device interface.
Signed-hostap: Arend van Spriel <arend@broadcom.com>
The .deinit() closes netlink for P2P Device. Before doing that remove
the P2P Device interface that was created by wpa_supplicant.
Signed-hostap: Arend van Spriel <arend@broadcom.com>
Add specific handler for creating the P2P Device to store the wdev_id as
this type of interface does not have an interface index.
Signed-hostap: Arend van Spriel <arend@broadcom.com>
To support Android the kernel may have a "p2p0" netdev for a P2P Device
even though this isn't very useful, but Android requires a netdev. To
support this in the supplicant, if the interface mode is P2P_DEVICE,
re-set it to the same instead of STATION mode.
Note that this is only possible with a kernel that creates a
netdev for the P2P Device wdev.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
Add an option to pass a handler to nl80211_create_iface() and
nl80211_create_interface_once() that will be called after receiving the
message from the kernel. This handler will add the option to process the
message in different ways for different interfaces.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Add wdev_id to i802_bss. wdev_id_set indicates whether this id is
available. Use wdev_id if assigned, instead of ifindex. Use wdev_id for
events that come from the kernel to identify the relevant interface.
This commit does not assign wdev_id value for the BSS yet, i.e., this is
only preparation for the value to be used in a future commit.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Check the supported interfaces attribute to identify support for
a dedicated P2P Device interface type. If set, update the driver
capabilities flag to notify the supplicant.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Rename is_p2p_interface() to is_p2p_net_interface() since it used to
identify network P2P interfaces to disable 802.11b rates on them.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Sometimes an interface name that cannot be resolved is given to the
set_key function, so print the ifname in addition to the ifidx.
Signed-hostap: Michael Braun <michael-dev@fami-braun.de>
Currently, hostapd_get_vlan_id_ifname() is used to determine if a given
vlan is valid *and* to actually determine the interface. This leads to
wpa_set_keys() sometimes setting the key on the wildcard interface name,
which does not make sense.
This patch therefore adds hostapd_vlan_id_valid() and makes
hostapd_get_vlan_id_ifname() not return a wildcard interface.
Signed-hostap: Michael Braun <michael-dev@fami-braun.de>
Currently, struct hostapd_vlan is a per-BSS data structure which
also contains informations about whether to remove the bridge
or clear wlan / tagged-vlan interface from the bridge.
In a multi-interface multi-BSS setup, this can lead to the following
race condition:
1. wlan0 creates VLAN A, sets DVLAN_CLEAN_BR and DVLAN_CLEAN_VLAN_PORT
2. wlan1 creates VLAN A, does not set DVLAN_CLEAN_BR and
DVLAN_CLEAN_VLAN_PORT as already there
3. wlan0 removes VLAN A, removes tagged-interface from the bridge
but not the bridge.
Now wlan1 VLAN A is unusable due to the missing uplink.
4. wlan1 removes VLAN A, does not cleanup
Solution:
This requires an inter-BSS inter-interface data structure to track the
bridge / bridge port usage within hostapd. This data structure could
also be used to track any other device-has-been-created-by-hostapd
information or when regarding interface freeing.
Signed-hostap: Michael Braun <michael-dev@fami-braun.de>
Currently by default, all BSS share the bridge brvlan%d.
While this is sane when no tagged-interface is given, this
is insane when different tagged interfaces are given, as
it would result in bridging those tagged interfaces.
This patch therefore uses br%s%d with %s=tagged_interface
and %d=VLAN ID as bridge name when a tagged-interface is given.
Signed-hostap: Michael Braun <michael-dev@fami-braun.de>
Currently, when different BSS using different tagged vlan
interfaces, they are forced to share the bridge brvlan#,
which is not desirable.
This patch fixes this by making the bridge name configurable.
Signed-hostap: Michael Braun <michael-dev@fami-braun.de>
When writing pcap-ng files, always include a radiotap
header even if there wasn't one in the input. For now
just drop prism headers, I don't have any to test.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
Add "StaAuthorized" and "StaDeauthorized" D-Bus interface in AP mode.
After enabling the AP mode of wpa_supplicant, the other process need to
get the MAC address and authorization status of every station, so
wpa_supplicant emits signal when the station is authorized or
deauthorized.
Signed-hostap: Chengyi Zhao <chengyix.zhao@gmail.com>
