The Beacon frame must include UUID-E and RF Bands attributes when
in active PBC mode to allow stations to figure out that two BSSes in
PBC mode is not a PBC session overlap.
A new ctrl_interface command, WPS_CANCEL, can now be used to cancel
a pending or ongoing WPS operation. For now, this is only available
with wpa_supplicant (either in station or AP mode). Similar
functionality should be added for hostapd, too.
The WSC 2.0 specification moved to use another design for the new
attributes to avoid backwards compatibility issues with some
deployed implementations.
If CONFIG_WPS_STRICT is set, validate WPS IE(s) in management frames and
reject the frames if any of the mandatory attributes is missing or if an
included attribute uses an invalid value. In addition, verify that all
mandatory attributes are included and have valid values in the WSC
messages.
If all the device information attributes use their maximum lengths,
a single WPS IE is not enough to fit in all the data and as such,
we must be able to fragment the data. In addition, the wpabuf needs
to be allocated larger to fit in maximum data.
Advertize list of authorized enrollee MAC addresses in Beacon and
Probe Response frames and use these when selecting the AP. In order
to provide the list, the enrollee MAC address should be specified
whenever adding a new PIN. In addition, add UUID-R into
SetSelectedRegistrar action to make it potentially easier for an AP
to figure out which ER sent the action should there be multiple ERs
using the same IP address.
This adds definitions and parsing of the new attributes that were added
in WPS 2.0. In addition, the version negotiation is updated to use the
new mechanism, i.e., accept everything received and use the new Version2
attribute in transmitted messages.
It looks like 10.6.3 and 10.6.4 do not like to receive Network Key
with WPA passphrase while PSK format still works. Use peer information
from M1 to figure out whether the Enrollee is likely to be OS X and
if so, force PSK format to be used for Network Key.
If the associating station indicates that it is intents to use WPS
by including WPS IE in (Re)Association Request frame, include WPS IE
in (Re)Association Response frame.
This attribute is supposed to indicate which methods the AP supports as
an Enrollee for adding external Registrars. It was left to 0 when the
AP code did not yet support external Registrars and was forgotten when
the ER support was added.
WPS IE parsing for PBC mode did not check whether the UUID-E attribute
was included before dereferencing the pointer. This could result in the
AP crashing when processing and invalid Probe Request frame.
Skip WPS IE building for Beacon and Probe Response frames is set_ie_cb()
is not set. This fixes a memory leak and optimizes operations by not
allocating memory and building the WPS IEs unnecessarily.
set_ap_wps_ie() is not used to set WPS IE for both Beacon and Probe
Response frames with a single call. In addition, struct wpabuf is used
instead of separate u8* and length fields. This avoids duplicated
allocation of the IEs and simplifies code in general.
Since an Enrollee that does not advertise display as one of the
Config Methods is unlikely to be able to show the ASCII passphrase
to the user, prefer PSK format with such an Enrollee to reduce key
derivation time. This can help with some low-powered devices that
would take long time to derive the PSK from the passphrase.
The use_psk_key parameter can now be used to force the Registrar to
use PSK format instead of ASCII passphrase when building a Credential
for the Enrollee. For now, this is not enabled, but it could be enabled
either based on external (to WPS) configuration or automatically set
based on some WPS attribute values from the Enrollee.
Instead of using the latest selected registrar change, collect selected
registrar information separately from all registrars and use the union
of this information when building the WPS IE for Beacon and Probe
Response frames.
Note: SetSelectedRegistrar UPnP action does not include a unique
identifier, so the ER matching routine is based only on the IP address
of the ER. In theory, there could be multiple ERs using the same IP
address (but different port or URL), so there may be some corner cases
that would not always match the correct ER entry at the AP. Anyway, this
is not really expected to occur in normal use cases and even if it did
happen, the selected registrar information is not any worse than it was
before when only the last change from any registrar for being
advertized.
In addition, start ordering header file includes to be in more
consistent order: system header files, src/utils, src/*, same
directory as the *.c file.
This makes it clearer which files are including header from src/common.
Some of these cases should probably be cleaned up in the future not to
do that.
In addition, src/common/nl80211_copy.h and wireless_copy.h were moved
into src/drivers since they are only used by driver wrappers and do not
need to live in src/common.
Use shared functions for converting Primary Device Type between binary
and string formats. In addition, use array of eight octets instead of a
specific structure with multiple fields to reduce code complexity.
Mainly, this is including header files to get definitions for functions
which is good to verify that the parameters match. None of these are
issues that would have shown as incorrect behavior of the program.
The WPS 1.0h specification is quite unclear on what exactly should be
used as the MAC Address value in the Credential and AP Settings. It
looks like this should after all be the MAC Address of the Enrollee,
so change Registrar implementation to use that address instead of the
AP BSSID.
In addition, add validation code to the Enrollee implementation to
check the MAC Address value inside Credential (and also inside AP Settings)
to make sure it matches with the Enrollee's own address. However, since
there are deployed implementations that do not follow this interpretation
of the spec, only show the mismatch in debug information to avoid breaking
interoperability with existing devices.
Previously, WSC_MSG was hardcoded for every message from ER, but
this needs to be changed based on message type to send a valid
message to the Enrollee via EAP transport.
New PINs can now be added to WPS ER. This results in the ER code
using SetSelectedRegistrar to modify AP state so that Enrollees
will be able to notice the actice registrar more easily.
Though we have such a timeout when handling SetSelectedRegistrar UPnP
message from an external registrar, it looks like we don't have one when
the internal registrar is activated for PIN connection. Thus we set the
SelectedRegistrar flag when AP is activated for PIN connection but we
never reset it - not by some timeout, nor when registration succeeds.
This lead to situations where AP everlastingly declare that it is
activated for WPS PIN connection when in reality it is not.
Use the same timeout (and also success with PIN) to clear the selected
registrar flag when using internal registrar, too.
If PBC session overlap is detected during an ongoing PBC protocol run,
reject the run (if M8, i.e., credentials, have not yet been sent). This
provides a bit longer monitoring time at the Registrar for PBC mode to
catch some cases where two Enrollees in PBC mode try to enroll
credentials at about the same time.
This provides information about PBC mode result from the WPS Registrar
module. This could be used, e.g., to provide a user notification on the
AP UI on PBC failures.
If PBC session overlap is detected between button press on the registrar
and M1 is reception, report session overlap with the Config Error
attribute in M2D to the Enrollee.
Store a copy of device attributes during WPS protocol run and make it
available for external programs via the control interface STA MIB
command for associated stations. This gives access to device name and
type which can be useful when showing user information about associated
stations.
wpa_supplicant can now reconfigure the AP by acting as an External
Registrar with the wps_reg command. Previously, this was only used
to fetch the current AP settings, but now the wps_reg command has
optional arguments which can be used to provide the new AP
configuration. When the new parameters are set, the WPS protocol run
is allowed to continue through M8 to reconfigure the AP instead of
stopping at M7.
Since we do not currently support changing the AP settings received
from M7, there is no point in actually sending out the M8 that would
likely trigger the AP to reconfigure itself and potentially reboot.
For now, we just receive the AP settings in M7 and add a local network
configuration block based on those, but NACK the message. This makes
wps_reg work like wps_pin, but by using the AP PIN instead of a client
PIN.
