The new default value (from 300 to 60 seconds) makes the internal P2P
peer list somewhat faster to react to peers becoming unreachable while
still maintaining entries for some time to avoid them disappearing
during user interaction (e.g., selecting a peer for a connection or
entering a PIN).
Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
A P2P Device while in the Listen state waiting to respond for the
obtained group negotiation request shall give a fair chance for other
concurrent sessions to use the shared radio by inducing an idle time
between the successive listen states. However, if there are no
concurrent operations, this idle time can be reduced.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Previously, GO Negotiation Request frame was used to update a peer entry
if only a Probe Request from that peer had been received. However, it
would be possible, even if unlikely, for a peer to be discovered based
on receiving Provision Discovery Request frame from it and no Probe
Request frame. In such a case, the Listen frequency of the peer would
not be known and group formation could not be (re-)initialized with that
peer. Fix this by allowing the GO Negotiation Request frame to update
peer entry if the current peer entry does not include Listen or
Operating frequency.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This adds one more case of active P2P peer detection so that
p2p_expire_peers() cannot hit a case where a GO Negotiation peer would
be removed.
Signed-hostap: Jithu Jance <jithu@broadcom.com>
The information of the peer's supported channel and operating class
is required for the driver to do TDLS off channel operations with a
compatible peer. Pass this information to the driver when the peer
station is getting added.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Some EAP methods can go through a step that is expected to fail and as
such, should not trigger temporary network disabling when processing
EAP-Failure or deauthentication. EAP-WSC for WPS was already handled as
a special case, but similar behavior is needed for EAP-FAST with
unauthenticated provisioning.
Signed-hostap: Jouni Malinen <j@w1.fi>
EAP-FAST requires pac_file to be configured, so make it clearer from the
debug output if missing configuration parameter was the reason for
EAP-FAST initialization failing.
Signed-hostap: Jouni Malinen <j@w1.fi>
The hash return buffer was previously left uninitialized in case
externally stored password ("password=ext:...") was used. This could
result in MSCHAPv2 failure if that uninitialized memory happened to be
something else than zero.
Signed-hostap: Jouni Malinen <j@w1.fi>
It is possible for the configuration to be temporarily invalid when
adding a new AP through SET commands followed by ENABLE. Avoid this
issue by using less strict validation on SET commands and perform full
configuration validation only on ENABLE. Use cases with configuration
file maintain their previous behavior, i.e., full validation after the
file has been read.
Signed-hostap: Jouni Malinen <j@w1.fi>
This reverts commit 792c8877c3
('P2P: Send GO Negotiation Confirm without wait').
Some drivers rely on the wait period for sending packets on the
off-channel. If the wait value is small, there's a race condition where
the driver ROC might complete before the packet was sent out. This
doesn't impede other drivers, as the wait is cancelled when a
Tx-completion arrives from the remote peer.
Signed-hostap: Arik Nemtsov <arik@wizery.com>
The missing call to scan_action_done() may keep us off-channel for 250
ms following sending GO Negotiation Response. In case the operating
channel is different from this channel and we're GO, a race could lead
to start beaconing while off-channel. This could potentially cause the
Beacon frames to go out on incorrect channel with some drivers.
Signed-hostap: Eyal Shapira <eyal@wizery.com>
The error path in bsd_init() on struct bsd_driver_data allocation was
jumping to location where drv is dereferenced. That will crash and it is
easier to just return from the function since no cleanup steps are
needed in this case.
Signed-hostap: Jouni Malinen <j@w1.fi>
Currently these three steps runs for each event.
1. get buffer size via system
2. allocate a memory for event
3. free the memory
The wpa_supplicant receives 4 events from boot to be connected.
So this patch prepare the event buffer at the init process.
I have tested wpa_supplicant on NetBSD 6.1.2.
But I could not tested hostapd because I do not have AP enabled device.
Signed-hostap: Masashi Honma <masashi.honma@gmail.com>
Replace channel_switch_supported flag of the
wpa_driver_nl80211_data by WPA_DRIVER_FLAGS_AP_CSA inside
wpa_driver_capa.flags. It makes more sense and also can
be accessed by wpa_supplicant.
Signed-hostap: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
This is just like the same command in wpa_supplicant, i.e., "hostapd_cli
status driver" can be used to fetch information about the driver status
and capabilities.
Signed-hostap: Jouni Malinen <j@w1.fi>
PEAPv2 implementation was not fully completed and there does not seem to
be any deployments of PEAPv2 nor any clear sign of such showing up in
the future either. As such, there is not much point in maintaining this
implementation in hostapd/wpa_supplicant.
Signed-hostap: Jouni Malinen <j@w1.fi>
The standard fragment_size network parameter can now be used to
configure EAP-pwd fragmentation limit instead of always using the
hardcoded value of 1020.
Signed-hostap: Jouni Malinen <j@w1.fi>
The standard fragment_size network parameter can now be used to
configure EAP-IKEv2 fragmentation limit instead of always using the
hardcoded value of 1400.
Signed-hostap: Jouni Malinen <j@w1.fi>
Setting methodState = DONE for the case where GPSK-1 is found to be
invalid or incompatible allows EAP state machine to proceed to FAILURE
state instead of remaining stuck until AP times out the connection.
Signed-hostap: Jouni Malinen <j@w1.fi>
phase1 parameter 'cipher' can now be used to specify which algorithm
proposal is selected, e.g., with phase1="cipher=1" selecting AES-based
design and cipher=2 SHA256-based. This is mainly for testing purposes,
but can also be used to enforce stronger algorithms to be used.
Signed-hostap: Jouni Malinen <j@w1.fi>
One of the RFC 4137 state transitions (METHOD -> FAILURE) had been
forgotten and this could result in EAP peer method processing not
reporting failure immediately and instead, remain stuck waiting for the
connection to time out. Fix this by adding the methodState == DONE &&
decision == FAIL case to allow immediate reporting of failures.
The condition from RFC 4137 as-is would cause problems for number of the
existing EAP method implementations since they use that in places where
the final message before EAP-Failure should really be sent to the EAP
server (e.g., WSC_Done in EAP-WSC). Address this by includng eapRespData
== NULL as an additional constraint for entering FAILURE state directly
from METHOD.
Signed-hostap: Jouni Malinen <j@w1.fi>
Commit e2f5a9889a was supposed to prevent
new scan request from pushing out the old one. However, it did not
really do that since eloop_deplete_timeout() returned 0 both for the
case where the old timeout existed (and was sooner) and if the old
timeout did not exist. It returned 1 only for the case where an old
timeout did exist and was larger than the new requested value. That case
used to result in wpa_supplicant_req_scan() rescheduling the timeout,
but hew code in eloop_deplete_timeout() did the exact same thing and as
such, did not really change anything apart from the debug log message.
Extend the eloop_deplete_timeout() (and eloop_replenish_timeout() for
that matter since it is very similar) to return three different values
based on whether the timeout existed or not and if yes, whether it was
modified. This allows wpa_supplicant_req_scan() to schedule a new
timeout only in the case there was no old timeout.
Signed-hostap: Jouni Malinen <j@w1.fi>
The new control interface command RADIO_WORK can be used by external
programs to request radio allocation slots from wpa_supplicant if
exclusive radio control is needed, e.g., for offchannel operations. If
such operations are done directly to the driver, wpa_supplicant may not
have enough information to avoid conflicting operations. This new
command can be used to provide enough information and radio scheduling
to avoid issues with such cases.
Signed-hostap: Jouni Malinen <j@w1.fi>
Avoid concurrent P2P scan requests with any other exclusive use of the
radio by using the radio work queuing mechanism. This removes some of
the earlier workarounds that postponed scans depending on other
operations.
Signed-hostap: Jouni Malinen <j@w1.fi>
If the port status did not change or would not need to get an update
after portEnabled changes, there is no need to try to set the driver to
use the same value it is already using based on the previous state.
Remove such calls to reduce number of operations during reassociation.
In addition, this cleans up the debug log by removing unnecessary
duplicated entries.
Signed-hostap: Jouni Malinen <j@w1.fi>
If the BSS table within wpa_supplicant is flushed, request the driver to
flush its own scan result table during the next scan. This can avoid
unexpected old BSS entries showing up after BSS_FLUSH or FLUSH command
in cases where the driver may maintain its internal cache of scan
results (e.g., cfg80211 BSS table persists at least for 15 seconds).
In addition to doing this automatically on BSS_FLUSH/FLUSH, a new SCAN
command argument, only_new=1, can be used to request a manual scan
request to do same. Though, it should be noted that this maintains the
BSS table within wpa_supplicant. BSS_FLUSH followed by SCAN command can
be used to clear all BSS entries from both the driver and
wpa_supplicant.
Signed-hostap: Jouni Malinen <j@w1.fi>
This debugging mechanism has now been deprecated by the control
interface commands that can be used to fetch same internal information
from hostapd in a more convenient way. Leave the empty USR1 signal
handler and configuration file parameter for backwards compatibility.
They can be removed in future versions of hostapd.
Signed-hostap: Jouni Malinen <j@w1.fi>
The per-STA/Supplicant state information from the EAPOL authenticator
is now available through "STA <MAC Address> eapol" command.
Signed-hostap: Jouni Malinen <j@w1.fi>
This adds TX/RX statistics and information about association into the
per-STA data that is available through the hostapd control interface. In
addition, information about the EAP method is now included with the IEEE
802.1X data.
Signed-hostap: Jouni Malinen <j@w1.fi>
These old driver wrappers have been removed quite some time ago, but
some of the build configuration notes were still describing how they
are configured.
Signed-hostap: Jouni Malinen <j@w1.fi>
Print into the debug log the list of vendor commands and events that the
driver supports. In addition, add a generic handler for vendor events.
This can be extended for each vendor/subcmd.
Signed-hostap: Jouni Malinen <j@w1.fi>
The P2P_PRESENCE_REQ command did not give any easily available
indication of the response received from the GO. Make this more useful
by providing such response (if received) as a ctrl_iface monitor event
(P2P-PRESENCE-RESPONSE).
Signed-hostap: Jouni Malinen <j@w1.fi>
intval is marked le16 and should be used through proper byte order
conversion functions even if it ended up getting set correctly due to
the two operations cancelling each other.
Signed-hostap: Jouni Malinen <j@w1.fi>
These were somewhat more hidden to avoid direct use, but there are now
numerous places where these are needed and more justification to make
the extern int declarations available from wpa_debug.h. In addition,
this avoids some warnings from sparse.
Signed-hostap: Jouni Malinen <j@w1.fi>
use_monitor=1 and force_connect_cmd=1 driver parameters can now be used
to force older monitor interface design and the connect API (SME in
driver) to increase hwsim testing coverage.
Signed-hostap: Jouni Malinen <j@w1.fi>
If Action frame registration in nl80211_mgmt_subscribe_non_ap() failed
for any frame type, the previous implementation skipped
nl80211_mgmt_handle_register_eloop() call. This is not desirable since
none of the Action frame types could be received and even worse, the
following nl80211_destroy_eloop_handle() call for nl_mgmt would likely
result in crashing the process due to the ELOOP_SOCKET_INVALID XOR
operation. This could be triggered at least in a P2P group interface
startup failure case.
Signed-hostap: Jouni Malinen <j@w1.fi>
Previously, it was possible for bss_info_handler() to end up dropping a
newer scan result entry if there were two entries with the same BSSID
and SSID (i.e., only frequency was different) and we were not associated
with either. This could happen, e.g., in some P2P use cases where device
discovery may happen on different channels. Fix this by checking the age
of the scan entries as well to prefer the most recent response.
Signed-hostap: Jouni Malinen <j@w1.fi>
Most of the attributes to these commands are identical and there is no
need to maintain two copies of the same functionality.
Signed-hostap: Jouni Malinen <j@w1.fi>
WPA_CIPHER_* and CIPHER_* are used for the exact same set of cipher
suites with the main difference being that the WPA_CIPHER_* version is
suitable to be used as a bitfield. Similarly, WPA_KEY_MGMT_* and
KEY_MGMT_* have similar design for AKMs. There is no need to maintain
two separate copies of the definitions since the bitfield compatible
version can be used for both needs. Get rid of the CIPHER_* and
KEY_MGMT_* versions to clean up the implementation by getting rid of
unnecessary mapping functions.
Signed-hostap: Jouni Malinen <j@w1.fi>
NL80211_ATTR_CONTROL_PORT was previously set only for
NL80211_CMD_ASSOCIATE, but it should also be set when using
NL80211_CMD_COMMAND (driver-based SME) even though none of the current
non-mac80211 drivers use this.
Signed-hostap: Jouni Malinen <j@w1.fi>
The option of handling upper layer P2P management operations within the
driver/firmware was originally planned to be used with wpa_supplicant,
but this has not really happened and there is no clear sign of this
being needed in the near term either. This functionality has not been
completed and it is certainly not being kept up-to-date or tested. As
such, it is best to remove it for now and if this or something similar
is needed in the future, it can be brought back once a clear need for it
has been demonstrated first.
Signed-hostap: Jouni Malinen <j@w1.fi>
prime_len was added to the start pointer twice and because of this, the
actual y coordinate was not verified to be valid. This could also result
in reading beyond the buffer in some cases.
Signed-hostap: Jouni Malinen <j@w1.fi>
phase1 parameters dhgroup, encr, prf, and mac can now be used to specify
which algorithm proposal is selected, e.g., with phase1="dhgroup=3
encr=1 prf=1 mac=1" selecting the mandatory-to-implement case. This is
mainly for testing purposes, but can also be used to enforce stronger
algorithms to be used.
Signed-hostap: Jouni Malinen <j@w1.fi>
These information elements are not really used anywhere in hostapd or
wpa_supplicant nor is there any plan to use them. As such, there is no
need to keep the code here either, so save couple of bytes here.
Signed-hostap: Jouni Malinen <j@w1.fi>
This driver event was used separately for some Action frames, but all
the driver wrappers converted to this from information that would have
been enough to indicate an EVENT_RX_MGMT event. In addition, the
received event was then converted back to a full IEEE 802.11 management
frame for processing in most cases. This is unnecessary complexity, so
get rid of the extra path and use EVENT_RX_MGMT for Action frames as
well as other management frame subtypes.
Signed-hostap: Jouni Malinen <j@w1.fi>
This can be used to silence compiler warnings in cases where #ifdef
blocks can leave some variables or functions unused and there is no
cleaner way of avoiding the warnings.
Signed-hostap: Jouni Malinen <j@w1.fi>
Commit 88b32a99d3 added support for using
some Action frame processing in hostapd for drivers that handle most of
SME/MLME internally (it added FT, this has since be extended for SA
Query and WNM). However, this was added in a way that ended up getting
both the hostapd_rx_action() and hostapd_action_rx() called for Action
frames. This could result in an attempt to process FT, SA Query, and WNM
Action frames twice.
There is need for more significant cleanup in Action frame processing in
hostapd depending on the driver type, but as a simple step to avoid
issues, skip the hostapd_action_rx() call if hostapd_rx_action()
processed the frame.
Signed-hostap: Jouni Malinen <j@w1.fi>
Even though this is a short timeout, it is at least theoretically
possible for the interface to be removed while waiting for
reconfiguration to start. Avoid issues with this by cancelling the
timeout on any WPS interface deinit. In theory, this should be postponed
until interface removal, but that does not fit very nicely to the
current wps_hostapd.c style.
Signed-hostap: Jouni Malinen <j@w1.fi>
Previously, wps_version_number was used only to test extensibility to
newer version numbers, but it can also be used to enable testing of
older versions (1.0), e.g., to avoid hitting some 2.0 specific
validation steps.
Signed-hostap: Jouni Malinen <j@w1.fi>
It is fine to try to cancel a registration that does not exist, so there
is no need to have the duplicated checks for eloop timeout and socket
registration.
Signed-hostap: Jouni Malinen <j@w1.fi>
It was already possible to configure hostapd and wpa_supplicant to use
FT-SAE for the key management, but number of places were missing proper
AKM checks to allow FT to be used with the new AKM.
Signed-hostap: Jouni Malinen <j@w1.fi>
Action frame RX report through EVENT_RX_ACTION did not indicate whether
the frame was protected or not even though that information is available
in mlme_event_mgmt(). hostapd_rx_action() has a workaround for setting
the protected flag for SA Query frames, but that did not apply for other
frames, like FT Action. This broke FT-over-DS when PMF is enabled with
newer kernel versions (i.e., the ones that do not use monitor interface
for receiving management frames).
Signed-hostap: Jouni Malinen <j@w1.fi>
The earlier changes to buffer EAPOL frames when not associated to avoid
race conditions (especially commit
3ab35a6603 but maybe something even before
that) broke PeerKey 4-way handshake. Fix this by using a separate check
before the race condition workaround to process PeerKey 4-way handshake
EAPOL-Key messages differently.
Signed-hostap: Jouni Malinen <j@w1.fi>
PeerKey entries need to be removed on disassociation and this needs to
be done in a way that cancels the possibly pending eloop timeout.
Signed-hostap: Jouni Malinen <j@w1.fi>
This is not really needed for anything and the standard does not require
such validation step to be made for Authentication frame transmission.
Signed-hostap: Jouni Malinen <j@w1.fi>
This can be useful for displaying the current STA state and also for
determining whether some operations are likely to fail or need
additional delay.
Signed-hostap: Jouni Malinen <j@w1.fi>
hostapd_drv_wnm_oper() needs to indicate an error if the driver callback
function is not implemented. Without this, the buf_len argument could
have been left uninitialized which could result in crashing the process.
Signed-hostap: Jouni Malinen <j@w1.fi>
This makes it easier to trigger the ESS Disassociation Imminent
operation from different sources.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This adds first steps at processing a BSS Transition Management Query on
the AP side. Mainly, the message is parsed and printed out in the debug
log and a minimal BSS Transition Management Request frame is sent as a
response. BSS Transition Management Response frame is also parsed and
details printed out in the debug log.
Signed-hostap: Jouni Malinen <j@w1.fi>
The previous version could end up calling WPA authenticator routines
even though the authenticator had not been initialized and this could
result in NULL pointer dereference.
Signed-hostap: Jouni Malinen <j@w1.fi>
This prepares wpa_supplicant for accepting cases where the AP does not
use group addressed frames.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
If the extended key usage of the AAA server certificate indicates
that the certificate is for client use, reject the TLS handshake.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
OCSP response may not include all the needed CA certificates, so use the
ones received during TLS handshake.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The five second timeout to call wps_er_deinit_finish() could potentially
be left behind when removing the ER data based on some other event. This
could result in double-freeing of wps_er context killing the process,
e.g., if the WPS ER functionality is stopped while in the process of
unsubscribing from an AP and then restarted.
In addition, AP entries could still be present in the
er->ap_unsubscribing list when the deinit timeout hits. These entries
would still maintain HTTP context pointing to the ER which would be
freed here and as such, the following HTTP client callback could refer
to freed memory and kill the process. Fix this by freeing AP entries
from ap_unsubscribing list when ER is deinitialized from timeout even if
such AP entries have not completed unsubscription from UPnP events.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Reduce race condition of the station trying to reconnect immediately
after AP reconfiguration through WPS by rescheduling the reload
timeout to happen after EAP completion rather than the originally
scheduled 100 ms after new configuration became known.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This enables more convenient protocol testing of station side
functionality in various error cases and unexpected sequences without
having to implement each test scenario within hostapd.
ext_mgmt_frame_handle parameter can be set to 1 to move all management
frame processing into an external program through control interface
events (MGMT-RX and MGMT-TX-STATUS) and command (MGMT_TX).
Signed-hostap: Jouni Malinen <j@w1.fi>
These files have been distributed only under the BSD license option
since February 2012. Clarify the license statements in the files to
match that to avoid confusion.
Signed-hostap: Jouni Malinen <j@w1.fi>
If configuration of the group key to the driver fails, move the WPA
group into failed state and indication group setup error to avoid cases
where AP could look like it is working even through the keys are not set
correctly.
Signed-hostap: Jouni Malinen <j@w1.fi>
This adds initial parts for supporting the new GCMP-256, CCMP-256,
BIP-GMAC-128, BIP-GMAC-256, and BIP-CMAC-256 cipher suites.
Signed-hostap: Jouni Malinen <j@w1.fi>
If secondary channel is provided for CSA, advertise it in the Secondary
Channel Offset element in Beacon and Probe Response frames.
Signed-hostap: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
When CSA flow starts, store the entire struct hostapd_freq_params and
not only CS frequency as it was before. The additional freq_params are
required to advertise CS supplementary IEs such as secondary channel,
wide bandwidth CS, etc.
Signed-hostap: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
This allows use of structs (and not only pointers) defined in drivers.h.
Remove also some not needed forward declarations and redundant includes.
Signed-hostap: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
The event debouncing isn't very accurate (since it doesn't
take sub-second resolution into account), but it should use
monotonic time anyway since it doesn't care about the wall
clock.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
The PBC ignore-start workaround just needs to check whether
the time is within 5 seconds, so should use monotonic time.
While at it, add a few more ifdefs to clearly separate the
code and variables needed.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
PBC sessions are just time-stamped when activated, and
eventually time out, so should use monotonic time.
While at it, make the code use os_reltime_expired().
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
The eloop already tracks the expiration/lifetime, and the expiration
isn't really used, so remove it. It should otherwise have used monotonic
time, but since it's not actually used, we can remove it instead.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
The RADIUS server needs to calculate uptime, which is relative
and thus should use monotonic time.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
Since the RADIUS client cares about relative time (retry timeout)
only, it should use monotonic time.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
The BSS table, scan timeout, and related functionality should use
monotonic time since they care about relative values (age) only.
Unfortunately, these are all connected, so the patch can't be split
further. Another problem with this is that it changes the driver wrapper
API. Though, it seems only the test driver is using this.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
This should probably have used monotonic time for entry timestamps, but
as those aren't used at all right now, so just remove them entirely.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The request retry loop only retries for 5 seconds, so any time
jumps would probably not affect it much, but it should be using
monotonic time nonetheless since it only cares about duration.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
Wall time jumps shouldn't affect MMIC failure/TKIP countermeasures,
so use monotonic time. Change the michael_mic_failure variable to
struct os_reltime for type-safety.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
Since the PMKSA cache only uses relative time, use the monotonic time
functions instead of wall time to be correct when the clock jumps.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
For type-safety, make sta->acct_session_start a struct os_reltime
and then use monotonic time for accounting. For RADIUS reporting,
continue to use wall clock time as specified by RFC 2869, but for
the session time use monotonic time.
Interestingly, RFC 2869 doesn't specify a timezone, so the value
is somewhat arbitrary.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
Do not assume the driver supports QoS Mapping, but instead, advertise
support for this only if CONFIG_INTERWORKING is defined and driver
indicates support for configuring QoS Map.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The driver_nl80211.c changes are needed to avoid compiler warnings
with two frequency attributes pointing to the same value.
Signed-hostap: Jouni Malinen <j@w1.fi>
If more BSSes are added in config file than are supported by the driver,
segmentation fault can appear. For this case, the interface_added flag
needs to be cleared if adding a new BSS fails.
Signed-hostap: Marek Kwaczynski <marek.kwaczynski@tieto.com>
Until now DFS was simply restarting the AP when radar was detected. Now
CSA is used to perform smooth switch to the new channel. Stations not
supporting CSA will behave as before.
Signed-hostap: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-hostap: Michal Kazior <michal.kazior@tieto.com>
This is needed for AP CSA. Since CSA must happen immediately after radar
is detected there's no time to perform CAC. Thus, radar channels must be
disabled when looking for a new channel to escape to after a radar is
detected.
Signed-hostap: Michal Kazior <michal.kazior@tieto.com>
Adds support for VHT by parsing bandwidth and center_freq{1,2}.
Signed-hostap: Michal Kazior <michal.kazior@tieto.com>
Signed-hostap: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Just the usual, with a new function os_reltime_initialized()
thrown in that checks whether time has ever been retrieved
(time can't be completely zero).
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
This helper functions checks whether a given entry has expired,
given the last active timestamp, the current time, and a timeout.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Based on priority, remove the connection with least priority whenever
a frequency conflict is detected.
Signed-hostap: Jithu Jance <jithu@broadcom.com>
Allow another EAP method to be tried if one of the enabled methods
fails. If all the remaining methods fail, reject connection by adding a
new METHOD_REQUEST -> FAILURE transition. Previously, this case resulted
in the state machine trying to send a message when none was available
and then waiting for a following event until timeout.
Signed-hostap: Jouni Malinen <j@w1.fi>
It is possible for the authentication server to be configured with a
PKCS #12 file that includes a private key, a server certificate, and a
CA certificate. This combination could result in server_cert and ca_cert
parameters not being present and that should still result in TLS context
getting initialized.
Signed-hostap: Jouni Malinen <j@w1.fi>
It was possible to configure hostapd in a way that could try to
initialize a TLS-based EAP method even when TLS library context was not
initialized (e.g., due to not configuring server or CA certificate).
Such a case could potentially result in NULL pointer dereference in the
TLS library, so check for this condition and reject EAP method
initialization.
Signed-hostap: Jouni Malinen <j@w1.fi>
Commit 390e489c0d extended hostapd BSS
interface removal capabilities. However, it ended up causing a
regression in wpa_supplicant P2P group interface handling. That P2P
group interface is removed through another driver_nl80211.c BSS context
and as such, the bss->added_if is not set. Fix this by verifying whether
the request is for another ifindex and if so, removing the interface
even if added_if is not marked.
Signed-hostap: Jouni Malinen <j@w1.fi>
Some non-mac80211 drivers, such as ath6kl, support STA inactivity timer
in firmware and may not provide connected stations' idle time to the
userspace. If the driver indicates support for offloaded operation, do
not start the inactivity timer in the hostapd.
Signed-hostap: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
struct beacon_data contains a lot of pointers. Make sure it gets cleared
to zero if hostapd_build_beacon_data() gets called from a path that does
not clear the structure first.
Signed-hostap: Janusz Dziedzic <janusz.dziedzic@tieto.com>
This is a mechanism used in Android to extend driver interface in vendor
specific ways. This is included only for the purpose of Android
compatibility. Proper interface commands should be used for any new
functionality.
Signed-hostap: Jouni Malinen <j@w1.fi>
Android uses a vendor specific library for implementing couple of driver
interface functions. Add the wrapper code to allow that mechanism to be
used.
Signed-hostap: Jouni Malinen <j@w1.fi>
Despite interface (and group) related sockets are not used
for control, they are created and may be left.
Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
Check if the BSS interface has started before setting beacon.
Lack of this condition can cause segmantation fault.
Signed-hostap: Marek Kwaczynski <marek.kwaczynski@tieto.com>
A reenable of the TDLS link while the host driver is already processing
the same (due to the retransmitted M2/M3 frames) might result in a
failed TDLS setup handshake due to some host driver's implementation.
Thus, issue enable link only when the peer's TDLS status signifies no
prior link (tpk_success=0).
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Commit de3cdf354a adding copying of the
STA's VHT capabilities into the STA entry on the AP. This was done in
allocated memory, but that new memory allocation was not freed anywhere.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Relative time shouldn't be calculated based on gettimeofday
because that clock can jump (e.g., when the time is adjusted
by the system administrator.)
On systems where that is available, use CLOCK_BOOTTIME (on
fairly recent Linux systems, this clock takes into account
the time spend suspended) or CLOCK_MONOTONIC (on Linux and
some POSIX systems, this clock is just freely running with
no adjustments.)
Reported-by: Holger Schurig <holgerschurig@gmail.com>
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
The 'started' state was tracked incorrectly. It also broke DFS
as it was using hostapd_enable/disable_iface() functions.
Signed-hostap: Michal Kazior <michal.kazior@tieto.com>
Some devices disable use of U-NII-1 (channels 36-48) for P2P due to it
being indoor use only in number of locations. If U-NII-3 (channels
149-161) is available, try to pick a channel from that range first
during random channel selection to reduce likelihood of interoperability
issues.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
If there are no other preferences from local configuration or driver,
prefer a random VHT channel instead of falling back to the fixed
pre-configured channel or 5 GHz/HT40 channel preference.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
If there are no other preferences from local configuration or driver,
prefer a random HT40 channel instead of falling back to the fixed
pre-configured channel or 5 GHz channel preference.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
If there are no other preferences from local configuration or driver,
prefer a random 5 GHz channel instead of falling back to the fixed
pre-configured channel (which is selected by default to be 1, 6, or 11).
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Use the new p2p_channel_select() function to select a VHT channel
at random when no other preferences are in effect.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Use the new p2p_channel_select() function to select an HT40 channel
at random when no other preferences are in effect.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The new p2p_channel_select() function can be re-used to implement
random channel selection from a set of operating classes in all
places that need such functonality.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This allows wlantest debug log output to be directed to a file so that
RELOG command can be used to rotate files more easily than stdout.
Signed-hostap: Jouni Malinen <j@w1.fi>
Add chan_switch to the control interface of wpa_supplicant and hostapd,
and also to wpa_cli and hostapd_cli.
Signed-hostap: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Build CSA settings and call the driver to perform the switch. Construct
Beacon, Probe Response, and (Re)Association Response frames both for CSA
period and for the new channel. These frames are built based on the
current configuration. Add CSA IE in Beacon and Probe Response frames.
Signed-hostap: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Add csa_settings struct which holds parameters for CSA. Change driver
interface for switch_channel(), so that it will receive this struct and
not only the new frequency as it was before. This allows wpa_supplicant
to provide all the required parameters (beacons, proberesp, assocresp,
CSA IE) which are required by cfg80211 implementation.
Signed-hostap: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
This was supposed to be a minimal sample of eloop wrapper, but it is
unclear whether this is of that much use and the file has not been kept
up-to-date. Remove this file to reduce maintenance effort. The other
eloop*.c files can be used as a starting point if something new is
needed.
Signed-hostap: Jouni Malinen <j@w1.fi>
Commit eb32460029 left an unneeded
sim_type argument to scard_init(). Remove that unnecessary argument to
clean up the implementation.
Signed-hostap: Masashi Honma <masashi.honma@gmail.com>
Add DBus methods for TDLS operations similar to those available
for the control interface. This includes Discover, Setup, and
Teardown commands. While here, add a method to query the TDLS
link status and add a DBus method for it.
Tested with CONFIG_TDLS enabled, on a TDLS-enabled host and
peer capable of TDLS:
dbus-send --system --dest=fi.w1.wpa_supplicant1 --print-reply \
/fi/w1/wpa_supplicant1/Interfaces/0 \
fi.w1.wpa_supplicant1.Interface.TDLSStatus string:<peer-mac-address>
yields: string "peer does not exist"
dbus-send --system --dest=fi.w1.wpa_supplicant1 --print-reply \
/fi/w1/wpa_supplicant1/Interfaces/0 \
fi.w1.wpa_supplicant1.Interface.TDLSDiscover string:<peer-mac-address>
yields no error
dbus-send --system --dest=fi.w1.wpa_supplicant1 --print-reply \
/fi/w1/wpa_supplicant1/Interfaces/0 \
fi.w1.wpa_supplicant1.Interface.TDLSSetup string:<peer-mac-address>
yields no error
dbus-send --system --dest=fi.w1.wpa_supplicant1 --print-reply \
/fi/w1/wpa_supplicant1/Interfaces/0 \
fi.w1.wpa_supplicant1.Interface.TDLSStatus string:<peer-mac-address>
yields: string "connected" after TDLS completes
dbus-send --system --dest=fi.w1.wpa_supplicant1 --print-reply \
/fi/w1/wpa_supplicant1/Interfaces/0 \
fi.w1.wpa_supplicant1.Interface.TDLSTeardown string:<peer-mac-address>
yields no error
dbus-send --system --dest=fi.w1.wpa_supplicant1 --print-reply \
/fi/w1/wpa_supplicant1/Interfaces/0 \
fi.w1.wpa_supplicant1.Interface.TDLSStatus string:<peer-mac-address>
yields: string "peer not connected"
Signed-hostap: Paul Stewart <pstew@chromium.org>
During persistent group re-invocation, GO may end up using a different
channel as the operation channel compared to what was indicated in the
invitation frames. This may break the connection if the peer device ends
up scanning the GO only on the channel from the invitation frame. Fix
this by using the negotiated channel (if available) on the GO as the
operating channel instead of the channel that was provided in the
p2p_invite command to start negotiation.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
We were not filtering the EVENT_CHANNEL_LIST_CHANGED events based on the
regulatory hint initiator. So wait for EVENT_CHANNEL_LIST_CHANGED event
after our own change was triggered even when regulatory hint initiator
was the driver. This could result in the wait for the channel list to be
updated to be terminated before the real change has occurred and as
such, old channel list remaining in use when configuring
hostapd/wpa_supplicant country parameter. Fix this by filtering the
hints according to the initiator and only regulatory hints initiated by
user will be used to stop the wait.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
If hostapd was started with the interface already in AP mode, leave the
interface in AP mode on deinit instead of unconditionally forcing it to
station mode.
Signed-hostap: Jouni Malinen <j@w1.fi>
It is common to build wpa_supplicant with AP mode support and it is
justifiable to clean up driver_nl80211.c by removing the conditional
build blocks based on hostapd vs. wpa_supplicant builds.
Signed-hostap: Jouni Malinen <j@w1.fi>
This gets rid of some ifdef HOSTAPD constructs and shares more
of the initialization code between hostapd and wpa_supplicant.
Signed-hostap: Jouni Malinen <j@w1.fi>
These variables were originally used in hostapd to clear HT channel
information when exiting. However, that functionality was lost with
commit f019981aee when moving to a common
code for setting the channel. Taken into account that no one seems to
have missed this functionality over the last four years, it seems safe
to drop this rather than try to fix the old hostapd behavior.
Signed-hostap: Jouni Malinen <j@w1.fi>
It's not possible to get a raw private key from keystore anymore, so
this would fail every time anyway. Remove it so it doesn't confuse
anyone that looks at this code.
Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
The new keystore ENGINE is usable to perform private key operations when
we can't get the actual private key data. This is the case when hardware
crypto is enabled: the private key never leaves the hardware.
Subsequently, we need to be able to talk to OpenSSL ENGINEs that aren't
PKCS#11 or OpenSC. This just changes a few #define variables to allow us
to talk to our keystore engine without having one of those enabled and
without using a PIN.
Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
If remaining AP session timeout is less than 5 seconds
for an existing station, replenish the timeout to 5 seconds.
This allows stations to be able to recycle a dialog token
value beyond 5 seconds for GAS exchange.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
eloop_replenish_timeout() finds a registered matching
<handler,eloop_data,user_data> timeout. If found, replenishes
the timeout if remaining time is less than the requested time.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
system/core/libnl_2 does not include nl_socket_set_nonblocking(), so
need to implement that to fix the build.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Add a parameter to send the overlapping BSS scan parameter
information element. This will require clients to perform
background scans to check for neigbors overlapping this
HT40 BSS. Since the implementation is incomplete it should
only be used for testing.
Signed-hostap: Paul Stewart <pstew@chromium.org>
If we are already connected to the selected AP with a network block
that was created based on the selected credential, do not force a
reconnection or network block update.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
It is possible for additional BSSs to be added while the primary
interface is still in the process of determining channel parameters (HT
co-ex scan, ACS, DFS). Do not enable secondary interfaces in such state
immediately, but instead, wait for the pending operation on the primary
interface to complete. Once that's done, the added extra BSSs will also
be enabled in hostapd_setup_interface_complete().
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Reject multiple calls to hostapd_setup_bss() for any specific interface.
hostapd_cleanup() must have been called first before trying to restart a
BSS.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
hostapd_bss_deinit() takes care of freeing the associated stations and
calling hostapd_cleanup() to deinit per-BSS services.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This reverts parts of commit 390e489c0d
that tried to enable removal of the first BSS. Since that operation is
now forced to remove all BSSs, these changes are not needed. The
hostapd_if_remove() operation in hostapd_free_hapd_data() is problematic
for the first BSS since it ends up freeing driver wrapper information
that is needed later when deinitializing the driver wrapper.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Since the control interface is now initialized as part of
hostapd_setup_interface(), it needs to be deinitialized on the error
path.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
If a secondary BSS is removed while it is waiting for the primary BSS to
complete channel setup (e.g., due to HT co-ex scan, ACS, or DFS), the
hostapd_data instance has not yet been initialized. Fix the BSS removal
code to take this special case into account and not try to deinitialize
the hostapd_data instance that has not yet been started.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The changes in commit 5592065850 to allow
any BSS to be removed were a bit too early since there are still number
of areas that use the first BSS as a special case. Especially the
driver_ops API is going to require quite a bit of cleanup before removal
of the first BSS without the other BSSes of the same radio can be done
safely.
For now, force all BSSs to be removed in case the first one is removed.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This call requires a struct hostapd_data pointer and that is not really
something that the driver wrappers should be using.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
It looks like abs() result is signed and gcc warns about this when
running a build with -O0 but not with -O2.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Limit the calls to eloop_terminate() to happen only for the
initialization failure from the interfaces that we specified on the
command line. This allows hostapd process to continue operating even if
a dynamically added interface fails to start up. This allows the upper
layer software to fix a configuration error and retry.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
When WFD Subelements are set, the IE in the Beacon frames of already
existing groups are not updated. This patch fixes this issue by setting
beacon_update to be 1 on WFD IE update.
Signed-hostap: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
The allocation was not verified to complete successfully and the
allocated memory was not freed on error paths.
Signed-hostap: Adriana Reus <adriana.reus@intel.com>
hostapd_set_freq_param() rejected the 20 MHz channel case with
vht_enabled due to the existing validation step including only 5 GHz (to
be more exact, only >= 5000 MHz). While the behavior may not be fully
defined for 2.4 GHz, we can enable this based on driver capability
advertisement to fix automatic VHT selection for P2P use cases.
mac80211_hwsim advertises VHT for 2.4 GHz band and that resulted in
failures when trying to start GO on that band with vht=1 parameter.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
NL80211_ATTR_CENTER_FREQ1 is defined to be used for anything but 20 MHz
bandwidth, so it could be unset for 20 MHz channels. Do not use it to
override center frequency from NL80211_ATTR_WIPHY_FREQ (if available)
for 20 MHz channels to avoid clearing frequency.
Signed-hostap: Jouni Malinen <j@w1.fi>
Better share the same function for initializing control interface from
the two possible paths that can add a new interface to hostapd.
Signed-hostap: Jouni Malinen <j@w1.fi>
This is a per-BSS configuration parameter and as such, needs to be
configured to the driver from hostapd_setup_bss() instead of
hostapd_driver_init().
Signed-hostap: Jouni Malinen <j@w1.fi>
DFS operations are specific to the interface (radio/wiphy), not BSS
(netdev/vif), so hostapd_iface is the appropriate element to use in
them.
Signed-hostap: Jouni Malinen <j@w1.fi>
If per-BSS configuration enabling did not provide a phy name, iface->phy
was left empty. It can be helpful to set this up automatically, so fill
that when initializing the interface.
Signed-hostap: Jouni Malinen <j@w1.fi>
Only scan the affected channels instead of all enabled channels when
determining whether the primary and secondary channel for HT40 needs to
be swapped. This speed up HT40 setup considerably on 5 GHz band.
Signed-hostap: Jouni Malinen <j@w1.fi>
If hostapd is requested to set the country code and the previous country
code differs from the new one, the channel list information from the
driver may change. This change may not be instant, so wait for an
EVENT_CHANNEL_LIST_CHANGED event before continuing interface setup with
fetching of the channel list information. This fixes issues where the
selected channel is not available based on the previous regulatory data
and update through CRDA takes some time.
Signed-hostap: Jouni Malinen <j@w1.fi>
Channel determination may take considerable time when ACS or DFS is
used, so it is useful to be able to observe this process through the
control interface. Move the initialization of the control interfaces to
happen before channel determination so that this can be achieved.
Signed-hostap: Jouni Malinen <j@w1.fi>
Use hostapd_interface_init2() for all interfaces instead of the
previously used different paths for per-interface-config and
per-BSS-config cases. This moves the calls to hostapd_driver_init() and
hostapd_setup_interface() to happen after all configuration files have
been read.
Signed-hostap: Jouni Malinen <j@w1.fi>
While these attributes may be expected to be present always, this needs
to be verified within driver_nl80211.c since we cannot depend on the
kernel/driver working correctly.
Signed-hostap: Jouni Malinen <j@w1.fi>
Previously, ENABLE command ended up freeing the hostapd_iface context on
initialization failures, but did not even remove the interface from the
list of available interfaces. This resulted in use of freed memory with
any following operation on the same interface. In addition, removing the
interface on initialization failure does not seem like the best
approach. Fix both of these issues by leaving the interface instance in
memory, but in disabled state so that the configuration can be fixed and
ENABLE used again to enable the interface or REMOVE used to remove the
interface.
Signed-hostap: Jouni Malinen <j@w1.fi>
Number of regressions had shown up in wpa_supplicant implementation of
SAE group selection due to different integer array termination (-1 in
hostapd, 0 in wpa_supplicant) being used for SAE groups. The
default_groups list did not seem to use any explicit termination value.
In addition, the sae_group_index was not cleared back to 0 properly
whenever a new SAE session was started.
Signed-hostap: Jouni Malinen <j@w1.fi>
When removing and re-adding the first wlan# netdev to hostapd
dynamically, the netdev is already present and should not be removed and
re-added to maintain its state as not-added-by-hostapd so that it does
not get removed automatically.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The global control interface command "REMOVE <ifname>" can now be used
to remove a single virtual interface (BSS) without affecting other
virtual interfaces on the same radio.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The global control interface command "ADD
bss_config=<phyname>:<config file>" can now be used to add a single
virtual interface (BSS) to an interface.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This moves the vif added check from core hostapd to the driver wrapper
(only driver_nl80211.c uses this) and reorders operations a bit to allow
the first BSS (vif) to be removed from a multi-BSS setup.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The first user of monitor interface was not counted and that could
result in the monitor interface getting removed if the initial interface
was removed from a multi-BSS setup.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Return control flow to hostapd by calling hostapd_acs_completed()
if requesting a scan from the underlying device fails.
Signed-hostapd: Helmut Schaa <helmut.schaa@googlemail.com>
If radar was detected single BSS is notified about it. This caused only
that single BSS to be stopped and restarted. However, due to nl80211
interface combinations the BSS was not started on a new channel and
other BSSes remained operating on the old channel.
The downside is that hostapd_disable_iface() causes deauth frames to be
sent. This is undesired but on the other hand it doesn't make sense to
create workarounds that imitate CSA's 'block tx'. For proper Tx
quiescing CSA should be properly implemented.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Decouple HT/VHT offset/center-freq calculations from channel lookup.
This will be necessary for further improvements on the DFS codebase.
Signed-hostap: Michal Kazior <michal.kazior@tieto.com>
The GTK rekey offload information was sent to the driver immediately
after the 4-way handshake which ended up being before the initial group
key exchange in the case of WPA (v1). This could result in even that
initial GTK handshake being offloaded and wpa_supplicant being left in
WPA_GROUP_HANDSHAKE state. Fix this by postponing the operation to
happen only after the full set of initial EAPOL-Key exchanges have been
completed (i.e., in the existing location for WPA2 and a after the group
key handshake for WPA).
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Reject RELOAD control interface command if the dynamic configuration
changes have resulted into a state where the configuration is invalid.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This allows the configuration validation routines to be called from
src/ap/*.c for runtime updates of configuration without reprocessing the
full configuration file.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This provides a new option for configuring multiple virtual interfaces
(BSS) that share a single radio. The new command line parameter
-b<phyname>:<config file name> is used to define one or more virtual
interfaces for each PHY. The first such entry for a new PHY is used to
initialize the interface structure and all consecutive parameters that
have the same PHY name will be added as virtual BSS entries to that
interface. The radio parameters in the configuration files have to be
identical.
This can be used as an alternative for the bss=<ifname> separator and
multiple BSSes in a single configuration file design while still
allowing hostapd to control the PHY (struct hostapd_iface) as a group of
virtual interfaces (struct hostapd_data) so that common radio operations
like OLBC detection and HT40 co-ex scans can be done only once per real
radio.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
