In many places in the code there was a reference to wpa_s->parent to get
from group interface to p2p_dev interface. These places can break if
P2P_DEVICE interface would need to be used with the primary interface as
the group interface, since the parent of the primary interface points to
itself and not the p2p_dev interface.
Fix this by adding a separate "p2pdev" pointer to wpa_supplicant,
it will be the same as parent pointer in most cases but whenever
the primary interface is used as a group interface, change it to
point to the correct p2p_dev interface.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
It does more than intended; apart from denying messages to that
particular interface it also denies all messages non-qualified with an
interface globally. This blocks messages completely unrelated to
wpa_supplicant, such as NetworkManager communication with the VPN
plugins.
From the dbus-daemon manual:
Be careful with send_interface/receive_interface, because the
interface field in messages is optional. In particular, do NOT
specify <deny send_interface="org.foo.Bar"/>! This will cause
no-interface messages to be blocked for all services, which is almost
certainly not what you intended. Always use rules of the form: <deny
send_interface="org.foo.Bar" send_destination="org.foo.Service"/>
We can just safely remove those rules, since we're sufficiently
protected by the send_destination matches and method calls are
disallowed by default anyway.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
If the config file for the interface says "p2p_disabled=1", don't report
p2p capabilities on this interface. This helps programs like Connman to
not enable p2p when it's been disabled in wpa_supplicant.
Signed-off-by: John Ernberg <john.ernberg@actia.se>
The maximum WPS Device Name length is 32 characters and that limit was
already enforced for the control interface and configuration files.
Signed-off-by: Purushottam Kushwaha <p.kushwaha@samsung.com>
At least one of the wpas_p2p_connect() callers (NFC join case) already
had access to the Group SSID. Pass that information through
wpas_p2p_connect() to wpas_p2p_join() so that the join operation can
filter out incorrect groups more easily.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The new methods are
1. VendorElemAdd "i" "ay" i=integer ay=array of bytes
2. VendorElemGet "i" i=integer (output array of bytes)
3. VendorElemRem "i" "ay" i=integer ay=array of bytes
These provide functionality similar to the control interface commands
VENDOR_ELEM_ADD, VENDOR_ELEM_GET, and VENDOR_ELEM_REMOVE.
Signed-off-by: Avichal Agarwal <avichal.a@samsung.com>
Signed-off-by: Purushottam Kushwaha <p.kushwaha@samsung.com>
Signed-off-by: Kyeong-Chae Lim <kcya.lim@samsung.com>
Signed-off-by: Mayank Haarit <mayank.h@samsung.com>
Signed-off-by: Dilshad Ahmad <dilshad.a@samsung.com>
[VendorElemGet to return array of bytes instead of string; cleanup]
Signed-off-by: Jouni Malinen <j@w1.fi>
The new max_oper_chwidth and freq2 arguments to P2P_CONNECT, P2P_INVITE,
and P2P_GROUP_ADD control interface commands can be used to request
larger VHT operating channel bandwidth to be used than the previously
used maximum 80 MHz.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Free the message after message send in
wpas_dbus_signal_p2p_invitation_received() to avoid leaking memory.
Signed-off-by: Mayank Haarit <mayank.h@samsung.com>
Signed-off-by: Avichal Agarwal <avichal.a@samsung.com>
This is similar to SAVE_CONFIG on control interface, which allow users
to update the configuration file.
Signed-off-by: Purushottam Kushwaha <p.kushwaha@samsung.com>
Signed-off-by: Mayank Haarit <mayank.h@samsung.com>
All interface globals are now exposed as D-Bus properties of type
string, and parsed via the normal interface global parsing functions.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Add a global D-Bus handler ExpectDisconnect for setting
wpa_s->own_disconnect_req flag. This flag will prevent wpa_supplicant
from adding blacklists and requesting incomplete scan upon the incoming
disconnection. This is mainly meant for a case where suspend/resume is
used and some external component knows about that and can provide the
information to wpa_supplicant before the disconnection happens.
Signed-off-by: Ningyuan Wang <nywang@google.com>
This is equivalent to the P2P_EVENT_INVITATION_RECEIVED signal on the
control interface. It can be used to sent the Invitation Received signal
to applications written using D-Bus.
Signed-off-by: Maneesh Jain <maneesh.jain@samsung.com>
This corrects the type of dev_passwd_id in GONegotiationRequest event.
This field is packed as DBUS_TYPE_UINT16 but in
wpas_dbus_interface_signals it was "i" which is DBUS_TYPE_INT32.
Signed-off-by: Nishant Chaprana <n.chaprana@samsung.com>
scan_freq and freq_list are not parsed correctly by
wpa_config_parse_int_array() if quoted.
Patch for dbus_old_handlers.c, the same change as done by Robert Shade
<robert.shade@gmail.com> for dbus_new_handlers.c in commit
99276998fa ('dbus: Do not quote scan_freq
and freq_list').
Signed-off-by: Jiří Klimeš <jklimes@redhat.com>
The P2P group is not yet operating when going through invitation
exchange for re-invocation. Previously, an old cached scan result could
be used to skip the scan immediately after the invitation exchange.
While this may result in the fastest possible connection, it does have
some issues with cases where the GO takes some time to start up. It
would also be at least theoretically possible for some of the BSS
parameters to be different, so having a fresh scan result from the new
GO instance may be desired in any case.
Add a mechanism to skip scan results that have been last updated before
a specific point in time and as the first user for this mechanism,
require chan results to be more recent than the invitation message
exchange for the P2P Client role in persistent group re-invocation case.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The D-Bus Scan() handler was setting wpa_s->scan_req = MANUAL_SCAN_REQ
on the code path that used wpa_supplicant_req_scan(). However, it did
not do anything similar for the cases where
wpa_supplicant_trigger_scan() is called directly. This could result in
unexpected wpa_s->last_scan_req value and incorrect behavior especially
when using ap_scan=2 and running a scan while operating in AP mode. Fix
this by explicitly setting wpa_s->last_scan_req = MANUAL_SCAN_REQ when
using wpa_supplicant_trigger_scan() from the Scan() handler.
Signed-off-by: Jouni Malinen <j@w1.fi>
Commit 38279bdb35 ('D-Bus: Coding style
cleanup') handled the dbus_new_handlers.c change properly, but misplaced
the second 'const' in dbus_old_handlers.c in a way that resulted in
duplicated const rather than marking the actual value const.
Signed-off-by: Jouni Malinen <j@w1.fi>
The variables here are unsigned and as such, cannot have a negative
value. Use == 0 instead of <= 0 to make this cleaner.
Signed-off-by: Jouni Malinen <j@w1.fi>
This is equivalent to the P2P_REMOVE_CLIENT command on control
interface. This can be used to remove the specified client [as object
path or string format interface address] from all groups (operating and
persistent) from the local GO.
Argument(s): peer[object path] OR iface[string format MAC address]
Signed-off-by: Purushottam Kushwaha <p.kushwaha@samsung.com>
Signed-off-by: Jijo Jacob <jijo.jacob@samsung.com>
This has same behavior as the ctrl_iface RECONNECT command.
Signed-off-by: Mayank Haarit <mayank.h@samsung.com>
Signed-off-by: Purushottam Kushwaha <p.kushwaha@samsung.com>
Add GO Intent information of connecting device in GO Negotiation Request
event which will help applications to decide its own GO intent value in
advance and can avoid failure cases when both devices use GO Intent 15
depending on application requirement.
Signed-off-by: Mayank Haarit <mayank.h@samsung.com>
Allow the Manufacturer information for a found P2P peer device to be
fetched through the D-Bus interface similarly to p2p_peer <mac address>
on ctrl interface.
Signed-off-by: Amit Khatri <amit.khatri@samsung.com>
Signed-off-by: Rahul Jain <rahul.jain@samsung.com>
Signed-off-by: Ashutosh Kaushik <k.ashutosh@samsung.com>
D-Bus used the p2p_dev member in struct wpa_supplicant to track the
interface used for P2P Device operations. However, this is not needed as
the interface used for P2P Device operations is stored in struct
wpa_global->p2p_init_wpa_s.
Replace all the redirections to wpa_s->p2p_dev with redirections to
wpa_s->global->p2p_init_wpa_s and removed this member as it is no
longer needed.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
This command is for a specific P2P group, not for the P2P Device
instance and as such, wpa_s pointer must not be replaced with the
interface that is used for P2P Device management.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
