It looks like NID_X9_62_prime192v1 is not available, so allow that group
to fail without failing the full ap_wpa2_eap_pwd_groups test case.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
It looks like NID_X9_62_prime192v1 is not available, so allow that group
to fail without failing the full sae_groups test case.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
These test cases added a new radio for the non-FST AP and while they
removed the radio itself, they did not remove the hostapd instance for
that radio. Remove that to avoid leaving behind invalid instances.
Signed-off-by: Jouni Malinen <j@w1.fi>
This verifies wpa_supplicant behavior in number of cases where the
external program opening a control interface socket does not behave
properly.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
ap_open_sta_enable_disable verifies that DISABLE_NETWORK that is issued
while connect/sme-connect radio work is pending is effective, i.e.,
prevents connection to disabled network.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The number of channels was not properly passed from the
run-all.sh script to the start.sh script. Fix it.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Add tests verifying a Coordination Protocol Transport exchange and
selection during P2PS provision discovery.
Signed-off-by: Max Stepanov <Max.Stepanov@intel.com>
Reviewed-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Reuse p2ps_provision() and p2ps_connect_pd() methods, and
remove the previous PD helper functions which are no longer used.
This fixes the previously "broken"
p2ps_connect_keypad_method_nonautoaccept and
p2ps_connect_display_method_nonautoaccept.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Reviewed-by: Max Stepanov <Max.Stepanov@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Re-factor p2ps_connect_p2ps_method() so it reuses generic P2PS provision
and connection flows.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
When MCC is enabled, the remain of channel scheduling might
incur additional delays, so increase the timeouts to be able
to receive delays frames.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Set peer_group_removed only if peer_group_added has already been set.
This fixes an issue where a propertiesChanged event triggered by an
earlier test case was able to get dbus_p2p_group_termination_by_go
terminated too early. This happened, e.g., with sequence
"dbus_p2p_two_groups dbus_p2p_group_termination_by_go".
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Only run peerJoined() steps once to avoid trying to use GetAll() on an
already removed group and double-removal of a group. This did not make
the test case fail, but the exception is printed out in pretty confusing
way to stdout, so better get rid of it.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Remove the duplicated -ddKt command line argument to avoid setting
hostapd debug level to EXCESSIVE.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
On recent kernels, it seems that something changed (scheduler?)
that makes hwsim send the scan done event so quickly that iw isn't
scheduled back in to listen for it, causing iw to get stuck.
Work around this by using the scan trigger command (it'll be quick
enough so that we don't really need to wait) and the scan trigger
and dump commands where the results are required (and use a small
sleep there instead of waiting for the scan results.)
I'll try to fix this separately in iw later.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This verifies P2P extended listen timing operations by confirming that a
peer is not discoverable during the provisioning step and that the peer
becomes discoverable after having removed the group during such
provisioning step. The latter case was broken until the 'P2P: Cancel
group formation when deleting a group during group formation' commit.
Signed-off-by: Jouni Malinen <j@w1.fi>
Verify that Groups list for a P2P Peer gets updated properly on group
addition and removal (three different paths).
Signed-off-by: Jouni Malinen <j@w1.fi>
omac1_aes_128() implementation within crypto_openssl.c is used in this
case and that cannot fail the memory allocation similarly to the
non-FIPS case and aes-omac1.c.
Signed-off-by: Jouni Malinen <j@w1.fi>
OpenSSL rejects the cipher string 'EXPORT' in FIPS mode in a way that
results in the locally generated error showing up before the EAP method
has been accepted.
Signed-off-by: Jouni Malinen <j@w1.fi>
In addition, replace some of the CHAP cases with PAP since that enables
more coverage without breaking the main test focus.
Signed-off-by: Jouni Malinen <j@w1.fi>
The PKCS12 file with default openssl options cannot be used with OpenSSL
1.0.1 in FIPS mode. Replace this with -descert version as a workaround.
Signed-off-by: Jouni Malinen <j@w1.fi>
This makes it easier to build wpa_supplicant for OpenSSL FIPS mode
testing. wpa_supplicant/.config needs following type of configuration
for this:
CONFIG_FIPS=y
CFLAGS += -I/usr/local/ssl/include
LIBS += -L/usr/local/ssl/lib
CC=/usr/local/ssl/fips-2.0/bin/fipsld
Signed-off-by: Jouni Malinen <j@w1.fi>
This allows driver-based preference list to override default operating
channel selection mechanism by using a non-social P2P find if needed.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Previously, this was assumed to be the case due to default channel
selection behavior. However, that may not be the case with driver-based
preference list processing. Enforce a social channel to be used as the
operating channel here since dev[2] uses social channel only device
discovery and needs to find the GO.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The openssl_ciphers="EXPORT" case may result in locally generated
disconnection event if the OpenSSL version used in the build rejects
export ciphers in default configuration (which is what OpenSSL 1.1.0
will likely do). Don't report a test case failure in such a case.
Signed-off-by: Jouni Malinen <j@w1.fi>
Add adv_cpt and seeker_cpt parameters to p2ps_provision() function.
The seeker_cpt is used in P2P_ASP_PROVISION command by a seeker, the
adv_cpt parameter is in P2P_ASP_PROVISION_RESP by an advertiser.
Signed-off-by: Max Stepanov <Max.Stepanov@intel.com>
Reviewed-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Add an optional parameter to p2ps_advertise() function allowing to
specify CPT priority values.
Signed-off-by: Max Stepanov <Max.Stepanov@intel.com>
Reviewed-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Add an optional CPT parameter to asp_provision() method of
WpaSupplicant.
Signed-off-by: Max Stepanov <Max.Stepanov@intel.com>
Reviewed-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Add p2ps_connect_pd() helper method which strictly validates the PD
results and establishes the connection between peers accordingly.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Reviewed-by: Max Stepanov <Max.Stepanov@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Add generic provision method. This method receives a seeker and an
advertiser devices, advertisement id, method, and a flag which indicates
whether deferred flow is expected. The method returns P2PS-PROV-DONE
events and the pin (if keypad or display method is used).
This method is needed to simplify the P2PS provision flows in the tests.
This method complies to the P2PS specification regarding the expected
order of the show and display PIN events.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Reviewed-by: Max Stepanov <Max.Stepanov@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Add asp_provision method which issues either P2PS PD Request or, if the
status is provided, continues the deferred flow by sending follow on
PD Request.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Reviewed-by: Max Stepanov <Max.Stepanov@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
This test case could fail if there were old BSS entries remaining in
cfg80211 scan results. That happened, e.g., when running test cases in
the following sequence: "discovery_social_plus_one discovery_auto".
Signed-off-by: Jouni Malinen <j@w1.fi>
This removes quite a bit of duplicated code. In addition, this starts
using different FST group names to get additional coverage.
Signed-off-by: Jouni Malinen <j@w1.fi>
Without this, the run-tests.py socket could have been left in attached
to receive all hostapd global events during a test case. This could hit
the limit of pending messages on the socket since there is nothing
clearing this socket during the execution of a test case. Fix this by
explicitly closing the socket after having completed the RELOG command.
Signed-off-by: Jouni Malinen <j@w1.fi>
This verifies FST group dialog_token wrap-around and behavior with large
number of session setups and teardowns.
Signed-off-by: Jouni Malinen <j@w1.fi>
This adds a test case that goes through session initialization through
separate commands that can be modified more easily for special case. The
first such special case is using special FST Setup Request frames with
non-standard MBIE contents to hit different code paths for finding the
interface.
Signed-off-by: Jouni Malinen <j@w1.fi>
Pass absolute path to the daemonized wpa_cli process and add read
privileges for everyone on the action script to make this test case work
better when run without a VM.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Try to use the special build for --codecov purposes, if present, instead
of hardcoding the hostapd/wpa_supplicant binary to the default location.
This is needed to collect code coverage correctly.
Signed-off-by: Jouni Malinen <j@w1.fi>
Commit 53606b105c ('tests: Wait for scan
to complete on all interfaces in reset()') added option of passing
ifname to get_driver_status(). This could result in FAIL-NO-IFNAME-MATCH
returns that get printed out in "Ignore unexpected status-driver line"
messages if the interface is not found. Check for this case to avoid
that unnecessary print.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Remove unused variables and replace split(" ") with just split().
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
When WpaSupplicant executes reset() it waits until all the ongoing scans
are completed. However, it checks the status of the wlanX interface
only. If a dedicated P2P device interface is used, scan may be still
running on the P2P Device interface, e.g., due to P2P_FIND. This might
affect subsequent tests.
Fix this by waiting until the scan is done both on wlanX and P2P
Device interfaces.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
This allows hostapd and wpa_supplicant to be built for hwsim test cases
with ubsan functinality from the recent gcc/clang compiler versions.
Signed-off-by: Jouni Malinen <j@w1.fi>
This changes the sae_groups test case design to try with every group and
skip triggering test failure for the heavier ones that are likely to
fail in some VM setups under load. This provides more testing coverage
by not limiting the test based on lowest common setup.
Signed-off-by: Jouni Malinen <j@w1.fi>
This verifies a case where the neighboring BSS is at the other end of
the band and has its PRI channel further away.
Signed-off-by: Jouni Malinen <j@w1.fi>
Flush the cfg80211 scan cache explicitly to avoid false failure reports
if a BSS entry from an earlier test case remain. Such a failure could be
hit, e.g., with the following test case sequence:
wpas_mesh_mode_scan p2p_channel_random_social dbus_old_wps_pbc
Signed-off-by: Jouni Malinen <j@w1.fi>
It looks like the previous timeout of 0.1 seconds could be hit under
parallel VM load, so double this to 0.2 second to avoid hitting
unnecessary test failures.
Signed-off-by: Jouni Malinen <j@w1.fi>
Get the P2P group interface name so it will be used for group removal to
support configurations that use a dedicated P2P Device interface.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Wait on the group control interface to support configurations that
use a dedicated P2P Device interface.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Use the global control interface to list the P2P Device persistent
networks. Get and parse the P2P-GROUP-STARTED events, so later the
interface names would be available for the connectivity test etc. Both
of these are required when a dedicated P2P Device interface is used.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Wait on the global control interface to support
configurations that use a dedicated P2P Device interface.
Note that the group interface cannot be used, as the group
interface name is not saved since no group was created.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Change the reset() method to use the global control interface
for resetting P2P state and also add a call to P2P_FLUSH.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
This adds test coverage to p2p_procesS_nfc_connection_handover() error
paths. This is also a regression test case for a memory leak on two of
these error paths.
Signed-off-by: Jouni Malinen <j@w1.fi>
This is a regression test case for a memory leak on a TLS PRF error
path. In addition, this provides more coverage for this error path.
Signed-off-by: Jouni Malinen <j@w1.fi>
The test sequence "scan_and_bss_entry_removed ap_wps_ap_scan_2" resulted
in failure due to an old BSS entry remaining from the first test case to
the second and the WPS_PBC operation on a forced BSSID ending up picking
the incorrect BSS entry. Make this more robust by clearing the scan
results from cfg80211.
Signed-off-by: Jouni Malinen <j@w1.fi>
Both of these test cases were leaving out BSS entries with active PBC
mode at the end of the test. This could result in the next text case
failing, e.g., in "ap_wps_pbc_overlap_2ap grpform_ext_listen" and
"ap_wps_pbc_overlap_2sta grpform_ext_listen" sequences. Fix this by
flushing the scan results more carefully at the end of the PBC overlap
test cases.
Signed-off-by: Jouni Malinen <j@w1.fi>
Verify that advertiser returns 'org.wi-fi.wfds' wildcard in a Probe
Response frame if at least one P2PS advertisement is present.
Signed-off-by: Max Stepanov <Max.Stepanov@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
This increases testing coverage for VENDOR_ELEM mechanism by explicitly
verifying that the requested element gets added to each of the supported
frame types.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Test P2PS GO and CLI discoverability on group operating channel.
In order to implement these tests, refactor p2ps_connect_p2ps_method
and test_p2ps_connect_adv_go_pin_method to reuse the code for
connection establishment. Also change p2ps_exact_seek so it will
allow getting Probe Response frames from several peers.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
test_p2ps_connect_adv_go_pin_method() expects that
p2ps_provision_keypad_method() returns P2PS-PROV-DONE with details
needed for a connection. However, this event was overridden which
resulted in an incorrect test flow skipping the connection
establishement. The test would pass, however, without really trying to
connect. Fix this by returning the correct event.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
This adds hwsim test ap_vlan_iface_cleanup_multibss. It connects two
stations in different BSS but the same hostapd process. First both
stations are in VLAN 1, then they get reauthenticated into VLAN 2. Due
to the ordering of the stations moving around, this test checks that
bridge and tagged interface referencing counting is done globally, such
that the tagged interface is not removed too early and no bridge is
left over.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
There seem to be cases where flush_scan_cache() was unable to clear all
BSS entries due to a hidden SSID BSS (SSID length 0) showing up again
from cfg80211 BSS table. Check for this and run the flush operation
again if any entries remain.
This fixes an issue where the following hwsim test case sequence
resulted in the last test case failing due to the old BSS entry from the
first test case being in place and showing unexpected flags information:
ap_hs20_min_bandwidth_home_hidden_ssid_in_scan_res
ap_hs20_remediation_required
ap_mixed_security
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
These are regression test cases for a segmentation fault issue (use of
freed memory) where interface removal happened while a gas-query item
was pending.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The standard hardcodes the MU Beamformee Capable subfield is hardcoded
to 0 when transmitting by an AP, so there is no need to provide a
configuration parameter for setting this to one.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The dev[1] <--> dev[2] data connectivity test was using incorrect
function. dev[2] is also using a P2P group and as such, can have a
different group interface.
Signed-off-by: Jouni Malinen <j@w1.fi>
Group interface name was fetched from the results of an incorrect group
formation and because of this, group removal failed in case P2P Device
is used and dev[1] ends up getting different group ifname for the
groups.
Signed-off-by: Jouni Malinen <j@w1.fi>
The network operations need to use the global control interface to be
performed on the interface that stores the network profiles for
persistent groups.
Signed-off-by: Jouni Malinen <j@w1.fi>
After P2P-GROUP-STARTED event, use group_form_result in order to update
the group_ifname for the device. This is needed when using P2P Device
for managing P2P operations which results in a separate group interface
being used.
Signed-off-by: Ben Rosenfeld <ben.rosenfeld@intel.com>
In case that there is a need to list the persistent P2P networks,
the global control interface needs to be used.
Signed-off-by: Ben Rosenfeld <ben.rosenfeld@intel.com>
list_networks() always used the wlanX control interface to query for the
current list of networks. However, when a dedicated P2P Device is used,
the global control interface should be used when checking persistent
group network profiles.
Fix this by adding an optional parameter indicating that the P2P
networks are requested, and in such a case use the global control
interface.
In addition update test_p2p_persistent to use the argument when needed.
Signed-off-by: Ben Rosenfeld <ben.rosenfeld@intel.com>
This is required for cases that a dedicated P2P Device interface
is used and then the event will happen on the global interface.
Signed-off-by: Ben Rosenfeld <ben.rosenfeld@intel.com>
Send request to set persistent_reconnect on the global control
interface so it would also work when using a dedicated P2P Device
interface.
Signed-off-by: Ben Rosenfeld <ben.rosenfeld@intel.com>
When testing P2P invitation flow, setting the NFC selector
should be done using the global control interface.
Signed-off-by: Ben Rosenfeld <ben.rosenfeld@intel.com>
Some tests in test_p2ps.py test a scenario where a separate P2P
group interface is not used. However, this is not a valid case
when a dedicated P2P Device interface is used, as in such a case
a separate group interface must be used.
Handle this by skipping such tests in case a dedicated P2P Device is
used.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Call group_form_result() whenever a new group is started, so that
group_ifname gets updated and later, the group can be removed when
needed.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
When resetting a device, remove all the P2P networks to prevent
unexpected behavior in following tests. This is needed for the case
where P2P Device interface is used.
Signed-off-by: Ben Rosenfeld <ben.rosenfeld@intel.com>
This is required for cases where P2P Device is used and the event
happens on the global interface.
Signed-off-by: Ben Rosenfeld <ben.rosenfeld@intel.com>
This is required for cases that multiple interfaces are used and the
event can happen on any of them, for example when a dedicated P2P Device
interface is used.
Signed-off-by: Ben Rosenfeld <ben.rosenfeld@intel.com>
The tests used p2p_dev_addr that can be different from own_addr,
if a dedicated P2P Device interface is used.
Signed-off-by: Ben Rosenfeld <ben.rosenfeld@intel.com>
Couple of the EAP-SIM/AKA protocol test cases were leaving out the
Reserved field. This was not intentional since these test cases were
targeting a specific Subtype processing instead of verifying truncated
header case (which is covered separately). Add the Reserved field to
allow the implementation to add an explicit, earlier check for this.
Signed-off-by: Jouni Malinen <j@w1.fi>
Number of the P2P test cases through D-Bus commands were not prepared
for there being a separate group interface when the P2P Device concept
is used.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Enhance test ap_vlan_wpa2_radius_id_change to change the VLAN-ID
back as a last step. This ensures that the wpa_group for VLAN-ID 1
did not enter FATAL_FAILURE state during the test.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
In addition, this adds some delay between the authentication and data
connectivity test through the newly added VLAN and by doing so, makes
ap_vlan_wpa2_radius_id_change a bit more robust. It was possible for the
EAPOL-Key message 4/4 not having yet been processed by hostapd at the
time the data test started.
Signed-off-by: Jouni Malinen <j@w1.fi>
dynamic_vlan=required also applies to macaddr_acl=2 (RADIUS), especially
when used with WPA-PSK.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
The time before trying to associate with an AP that does not advertise
Selected Registrar TRUE is going to be incremented, so increase the
autogo_m2d timeout to avoid reporting incorrect errors due to missing
M2D events.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This change add two new tests to verify hostapd operation when used with
VLANs. Both are based on pmksa_cache_preauth and enable dynamic VLANs,
pmksa_cache_preauth_vlan_used additionally uses a station with VID 1.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
It looks like it was possible to receive an incomplete FAIL line and
break out from test execution due to a parsing error. Handle this more
robustly and log the error.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Now that there is a kernel patch for IPv6 ProxyARP that is capable of
using the non-AP STAs MAC address as the link layer source address in
NA, validate that behavior rather than the temporary check for BSSID.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The 'params' argument was not used at all. Use it as an alternative
means for setting the list of test cases to execute.
Signed-off-by: Jouni Malinen <j@w1.fi>
Explicitly clear cached scan results on the AP interface before starting
ACS. This avoids issues where conflicting BSS entries from previously
executed test cases could affect channel selection.
Signed-off-by: Jouni Malinen <j@w1.fi>
This can be used to filter out test cases that take significantly longer
time to execute (15 seconds or longer). While this reduces testing
coverage, this can be useful to get a pretty quick coverage in
significantly faster time.
Signed-off-by: Jouni Malinen <j@w1.fi>
It's somewhat annoying that you can only run parallel-vm.py as
./parallel-vm.py, not from elsewhere by giving the full path,
so fix that by resolving the paths correctly in the scripts where
needed.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Instead of hand-writing a (positional) parser, use the argparse module.
This also gets us nice help output.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
These test cases need to use the previous-AP-on-correct-band workaround
similarly to test_ap_acs.py test cases for now to work with
mac80211_hwsim limitations on channel survey.
Signed-off-by: Jouni Malinen <j@w1.fi>
Explicitly clear the cfg80211 BSS cache at the beginning of these test
cases to avoid matching BSS flags against incorrect AP.
Signed-off-by: Jouni Malinen <j@w1.fi>
It looked like cfg80211 BSS entry for the zero-length SSID could remain
after this test case. Stop the AP and scan twice with flush-cache option
to make this less likely to occur and cause issues to following test
cases.
Signed-off-by: Jouni Malinen <j@w1.fi>
It was possible for this test case to fail if cfg80211 BSS cache
included an entry for the same BSSID on another channel from an earlier
test case. Fix this by epxlicitly flushing the cache. In addition, use
scan_for_bss() to make the test less likely to fail in case of heavy CPU
load.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The way the current channel survey is implemented in mac80211_hwsim
requires for the ACS test cases to be run immediately after the same
radio has been on the expected operating band. This was worked around in
one of the test cases and errors ignored in couple. Extend this
workaround to cover all the test cases.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
It looks like the IP routing table changes used here to trigger
unreachability and following reachability of the server do not work very
well with full IP routing configuration, so run this test case only when
executed under vm-run.sh.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
These test cases verify that P2P_FIND and P2P_LISTEN operation continues
after having replied to GO Negotiation Request frame for which we are
not yet ready (i.e., GO Negotiation Response with status=1).
Signed-off-by: Jouni Malinen <j@w1.fi>
It was possible for this test case to start a new group formation on
dev[1] while the first round was still going through the process of
processing group termination indication. That could result in the second
round failing unexpectedly.
Signed-off-by: Jouni Malinen <j@w1.fi>
It looks like the 128M default memory size for the hwsim test setup was
not large enough to cover all the needs anymore. Some of the test cases
using tshark could hit OOM with that size. Increase the default
allocation to 192M to avoid this type of issues.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This verifies that the packet socket workaround does not get disabled if
EAPOL frames are processed during operation state (i.e., when processing
reauthentication/rekeying on a functional association).
Signed-off-by: Jouni Malinen <j@w1.fi>
This allows multiple dmesg files to be saved if a test case is executed
multiple times similarly to the other logfiles.
Signed-off-by: Jouni Malinen <j@w1.fi>
The kernel had two bugs (one in hwsim and one more important one in
mac80211) in this area, add a test to make sure we can disconnect
without any kernel issues while in powersave.
Also make sure that the TIM bit gets set and cleared again (by checking
with tshark.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
It seems to be possible for dev2 (the one with incorrect password) to
stop retries before either dev0 or dev1 reports the authentication
failure event. For now, allow the test case pass if either dev0 or dev1
reports the event rather than requiring both to report this. The
expected behavior can be fine-tuned in the future if the reporting
behavior is modified to be more consistent.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Due to a copy-paste error, these test cases left 4addr mode enabled on
wlan5. This resulted in number of connect_cmd_* test cases failing if
executed after the wpas_in_bridge tests.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The new wpa_supplicant configuration file writing style leaves behind
the temporary file (<filename>.tmp) if renaming fails. Clean that up in
the test case execution.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This test cases used to fail if dev1 had seen dev0 as a GO in an earlier
test case, e.g., when running it after autogo_fail. Fix this by clearing
scan results on dev1 at the beginning of the test case.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This is a regression test for an earlier bug that resulted in using
freed memory after a P2P group interface was removed as part of
fallback-to-GO-Negotiation in P2P_CONNECT-auto.
Signed-off-by: Jouni Malinen <j@w1.fi>
It is possible for a low powered CPU to take excessively long time to
delete 1000 network blocks when running under valgrind. This would have
resulted in the test case failing and the following reset operation
timing out which would then stop the test sequence completely.
Signed-off-by: Jouni Malinen <j@w1.fi>
1. Add get_group_ifname() to wpasupplicant.py
2. Use the function to get the interface name for the bridge.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
run-tests.py is running as root, so sudo does not need to be used
anymore from within each test case.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
There is no need to use sudo and external rm to remove files now that
run-tests.py is required to run as root.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The new wpa_supplicant configuration writing design (rename instead of
write to original file) did not fail with the symlink-to-self case, so
replace this with the config file being replaced with a directory. In
addition, get rid of unnecessary use of subprocess since run-tests.py is
running as root nowadays.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
1. Modify discovery_stop to use global control interface when calling
P2P_FLUSH.
2. Modify p2p_listen_and_offchannel_tx to use the global control
interface when waiting for P2P PD event.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Some of the tests used p2p_dev_addr() that can be different from
own_addr() if a dedicated P2P Device interface is used.
Signed-off-by: Ben Rosenfeld <ben.rosenfeld@intel.com>
Some of the tests used p2p_dev_addr() that can be different from
own_addr() if a dedicated P2P Device interface is used.
Signed-off-by: Ben Rosenfeld <ben.rosenfeld@intel.com>
The test used p2p_dev_addr() that can be different from own_addr()
if a dedicated P2P Device interface is used.
Signed-off-by: Ben Rosenfeld <ben.rosenfeld@intel.com>
The test used p2p_dev_addr() that can be different from own_addr()
if a dedicated P2P Device interface is used.
Signed-off-by: Ben Rosenfeld <ben.rosenfeld@intel.com>
Fix the destination address that is sent in the WNM-Notification to be
the BSS address opposed to the P2P address.
Signed-off-by: Matti Gottlieb <matti.gottlieb@intel.com>
This is needed for cases that the group interface differs from the main
interface, i.e., when a dedicated P2P Device interface is used.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
When the 'SET' command is used to configure parameters related to P2P
operation use the global control interface and not the per interface one
as otherwise the setting will only have effect on the interface and will
work if a dedicated P2P_DEVICE is used.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Once the connection is established need to call group_form_result() on
the invited device, as otherwise the group interface name is not updated
and the connectivity test is done with the main interface instead of the
group interface.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
These are far from perfect since timing is quite difficult to match for
the case that behaved incorrectly. Anyway, it looks loke
p2p_service_discovery_peer_not_listening was able to hit the error now
and then, so this should be sufficient as a regression test case.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Include actual extended listen period in the test and confirm that the
device was available on a social channel during such period by using
non-social operating channel.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This test case is modifying the list of enabled config_method values and
needs to restore "p2ps" option that is included by default. Without
this, P2PS executed after dbus_get_set_wps could fail.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
It was possible for the GTK-found-in-memory case to be triggered due to
a retransmission of EAPOL-Key msg 3/4 especially when running test cases
under heavy load (i.e., timeout on hostapd due to not receiving the 4/4
response quickly enough). Make this false failure report less likely by
waiting a bit longer after the connection has been completed before
fetching the process memory.
Signed-off-by: Jouni Malinen <j@w1.fi>
Use another AP instance as a separate bridge port in the proxyarp_open
test cases to increase testing coverage for kernel proxyarp
functionality.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Commit 2e1d7386e2 ('tests: Refactor tshark
running') added a helper function for running tshark. However, it did
not use the filter argument correctly, added an extra -Tfields on the
command line, and failed to use global variable. In practice, this ended
up disabling all the tshark sniffer checks. Fix that by using the filter
argument from the caller and marking the _tshark_filter_arg global.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The hostapd_oom_wpa2_eap test case did not always catch these code
paths, so add a variant of that test case explicitly targeting RADIUS
functions.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This ends up using the special User-Name = STA MAC address case for
Accounting-Request. In addition, add Chargeable-User-Identity for one of
the STAs.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This extends the VENDOR-TEST EAP method peer implementation to allow
pending processing case to be selected at run time. The
ap_wpa2_eap_vendor_test test case is similarly extended to include this
option as the second case for full coverage.
Signed-off-by: Jouni Malinen <j@w1.fi>
This extends testing coverage of PMF group management cipher suites to
include all the cases supported by the driver (existing BIP =
AES-128-CMAC and the new BIP-GMAC-128, BIP-GMAC-256, BIP-CMAC-256).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Reorder scanning in a way that allows the ER behavior to be more
predictable. The first Probe Request report is for a previously received
frame on the AP and this new sequence avoids leaving either of the PBC
test STAs to be that one.
Signed-off-by: Jouni Malinen <j@w1.fi>
This makes testing under very heavy load or under extensive kernel
debugging options more robust by allowing number of test cases to scan
multiple times before giving up on active scans. The main reason for
many of the related test failures is in Probe Response frame from
hostapd not getting out quickly enough especially when multiple BSSes
are operating.
Signed-off-by: Jouni Malinen <j@w1.fi>
This verifies that PBC session overlap detection does not get indicated
when forming the group with the same peer multiple times.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This is a regression test case for a specific sequence that could result
in wpa_supplicant NULL dereference when a SD request is cancelled before
the SD Request TX status callback has been processed.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This set of notes provides information on how virtual guess OS can be
used to run the mac80211_hwsim test cases under any host OS. The
specific example here uses Ubuntu 14.04.1 server as the starting point
and lists the additional packages that need to be installed and commands
that can be used to fetch and build the test programs.
Signed-off-by: Jouni Malinen <j@w1.fi>
There were couple of common cases where the control interface for the
dynamic wpa_supplicant instance could have been left in attached state
until Python ends up cleaning up the instance. This could result in
issues if many monitor interface events were queued for that attached
socket. Make this less likely to cause issues by explicitly detaching
and closing control interfaces before moving to the next test case.
Signed-off-by: Jouni Malinen <j@w1.fi>
It was possible for the Action frame used for entring WNM Sleep Mode to
get dropped on the AP side due to it arriving prior to having processed
EAPOL-Key message 4/4 due to a race condition between Data and
Management frame processing paths. Avoid this by waiting for
AP-STA-CONNECTED event from hostapd prior to trying to enter WNM Sleep
Mode. In addition, make the check for the STA flag change more robust by
allowing the wait to be a bit longer with a loop that terminates as soon
as the flag has changed.
Signed-off-by: Jouni Malinen <j@w1.fi>
When the STA is forced to disconnect immediately after completion of
4-way handshake, there is a race condition on the AP side between the
reception of EAPOL-Key msg 4/4 and the following Deauthentication frame.
It is possible for the deauthentication notification to be processed
first since that message uses different path from kernel to user space.
If hostapd does not receive EAPOL-Key msg 4/4 prior to deauthentication,
no PMKSA cache entry is added. This race condition was making the test
cases expecting PMKSA caching to work to fail every now and then. Avoid
this issue by waiting for AP-STA-CONNECTED event from hostapd. This
makes sure the PMKSA cache entry gets added on the AP side.
Signed-off-by: Jouni Malinen <j@w1.fi>
It looks like this test case is failing every now and then, so add some
more time for the olbc_ht value to get updated before reporting a
failure.
Signed-off-by: Jouni Malinen <j@w1.fi>
It looks like the gobject module does not get installed by default for
Python at least on Ubuntu server, so modify the D-Bus test case files to
import this in a way that allows other test cases to be run even without
gobject module being installed.
Signed-off-by: Jouni Malinen <j@w1.fi>
This test case uses get_bss() with a BSSID to find a BSS entry. That can
result in failures if there are multiple BSS entries in wpa_supplicant
BSS table for the same BSSID, e.g., due to an earlier hidden SSID test
case. Explicitly clear the cfg80211 and wpa_supplicant scan caches at
the beginning of this test case to make it less likely for earlier test
cases to trigger a failure here.
Signed-off-by: Jouni Malinen <j@w1.fi>
This test case uses get_bss() with a BSSID to find a BSS entry. That can
result in failures if there are multiple BSS entries in wpa_supplicant
BSS table for the same BSSID, e.g., due to an earlier hidden SSID test
case. Explicitly clear the cfg80211 and wpa_supplicant scan caches at
the beginning of this test case to make it less likely for earlier test
cases to trigger a failure here.
Signed-off-by: Jouni Malinen <j@w1.fi>
This step requires kernel changes that are not yet in upstream Linux
tree, so mark this as skip rather than failure for now.
Signed-off-by: Jouni Malinen <j@w1.fi>
Use SELECT_NETWORK instead of REASSOCIATE for the first reconnection to
avoid unnecessary long wait for temporary network disabling to be
cleared. In addition, wait for the disconnect event after issuing the
DISCONNECT commands to avoid issues due to any pending events during the
immediately following reconnection attempt.
Signed-off-by: Jouni Malinen <j@w1.fi>
This makes it easier to figure out what happened if the test case fails
due to not finding all the needed OSU-PROVIDER information.
Signed-off-by: Jouni Malinen <j@w1.fi>
The external cfg80211 scan flushing operation requires a relatively
recent iw version and not all distributions include that. Avoid false
failure reports by marking these test cases skipped if the iw command
fails.
Signed-off-by: Jouni Malinen <j@w1.fi>
Due to a typo and missing hapd variable initialization, some of the DFS
and VHT test cases were marked as failures even though they were
supposed to be marked as skipped in case the kernel and wireless-regdb
did not have sufficient support for these modes.
Signed-off-by: Jouni Malinen <j@w1.fi>
If dbus_probe_req_reporting was run before dbus_probe_req_reporting_oom,
the SubscribeProbeReq() method succeeded since the memory allocation
that was supposed to fail in the OOM test case was not even tried.
Signed-off-by: Jouni Malinen <j@w1.fi>
This is a regression test case to detect a failure that resulted in an
up to five second busy loop through wpa_supplicant_fast_associate() when
interworking_find_network_match() and wpa_supplicant_select_bss() get
different matching results.
Signed-off-by: Jouni Malinen <j@w1.fi>
If Calling-Station-Id matches, but CUI does not, NAS is expected to
reject the request instead of accepting it. Verify that Disconnect-NAK
is returned for this.
Signed-off-by: Jouni Malinen <j@w1.fi>
This verifies that wpa_supplicant reconnects if PMF is enabled,
unprotected Deauthentication/Disassociation frame is received, and the
AP does not reply to SA Query.
Signed-off-by: Jouni Malinen <j@w1.fi>
This verifies that Certification signals include the expected
information on peer certificates and that dNSName constraint can be
configured based on that and is working both in matching and not
matching cases.
Signed-off-by: Jouni Malinen <j@w1.fi>
This test case was verifying that the first unused VENDOR_ELEM value
above the current maximum is rejected. That makes it a bit inconvenient
to add new entries, so increase the elem value to leave room for new
additions without having to continuously modify this test case.
Signed-off-by: Jouni Malinen <j@w1.fi>
This increases testing coverage for OCSP processing by confirming that
valid OCSP response showing revoked certificate status prevents
successful handshake completion. In addition, unknown certificate status
is verified to prevent connection if OCSP is required and allow
connection if OCSP is optional.
Signed-off-by: Jouni Malinen <j@w1.fi>
GnuTLS has a hardcoded three day limit on OCSP response age regardless
of the next update value in the response. To make this work in the test
scripts, try to generate a new response when starting the authentication
server. The old mechanism of a response without next update value is
used as a backup option if openssl is not available or fails to generate
the response for some reason.
Signed-off-by: Jouni Malinen <j@w1.fi>
This is more robust than checking the driver capability because it is
also possible for the wpa_supplicant build to be configured without mesh
support regardless of whether the driver supports it.
Signed-off-by: Jouni Malinen <j@w1.fi>
This makes it more convenient to run tests with wpa_supplicant builds
that do not support SAE (e.g., due to crypto library not providing
sufficient functionality for this).
Signed-off-by: Jouni Malinen <j@w1.fi>
This format as a DER encoded blob is supported by both OpenSSL and
GnuTLS while the previous OpenSSL specific format did not get accepted
by GnuTLS.
Signed-off-by: Jouni Malinen <j@w1.fi>
With GnuTLS, domain_suffix_match is currently requiring full match, so
split the test cases in a way that can be reported more cleanly as PASS
or SKIP based on TLS library behavior.
Signed-off-by: Jouni Malinen <j@w1.fi>
Proper configuration should be used here to get server validation
enabled, so update the test cases to provide the ca_cert parameter. This
was included in number of existing test cases, but not all.
Signed-off-by: Jouni Malinen <j@w1.fi>
These parameters are supported only with OpenSSL, so split any test case
that used those for a successful connection into two test cases. Skip
all test cases where these are used without the selected TLS library
supporting them to avoid reporting failures incorrectly. Though, verify
that subject_match and altsubject_match get rejected properly if TLS
library does not support these.
Signed-off-by: Jouni Malinen <j@w1.fi>
Check wpa_supplicant EAP capability and skip EAP-pwd and EAP-FAST test
cases if the build did not include support for these. This is cleaner
than reporting failures for such test cases when the selected TLS
library does not support the EAP method.
Signed-off-by: Jouni Malinen <j@w1.fi>
This network profile parameter will be removed with the cleanup that
makes mesh use shared functions for setting channel parameters. That
will allow HT to be enabled automatically based on driver capabilities.
Signed-off-by: Jouni Malinen <j@w1.fi>
Refactor the code to run tshark into its own submodule. This allows
even remembering whether -Y or -R needs to be used for filtering.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
These test cases run hostapd interface setup multiple times with
TEST_ALLOC_FAIL commands triggering memory allocation failures one by
one at each possible location in the setup sequence. Effectively, these
test cases will hit most error paths for memory allocation issue cases
(i.e., only the cases requiring more than one allocation failure in a
sequence are not covered).
Signed-off-by: Jouni Malinen <j@w1.fi>
Instead of returning "skip" from the test function, raise the new
HwsimSkip exception to indicate a test case was skipped.
Signed-off-by: Jouni Malinen <j@w1.fi>
There is a race condition between wlantest having received and written
the sniffer log and this test case using tshark to process it. Wait one
second before running tshark to make it less likely to get truncated
results that can result in the test case failing.
Signed-off-by: Jouni Malinen <j@w1.fi>
Verify error cases in bgscan module parameters. Increase learn bgscan
module coverage with parsing of the saved data and probe frequency
selection.
Signed-off-by: Jouni Malinen <j@w1.fi>
Verify correct behavior with invalid commands. In addition, allow minor
mac80211_hwsim modifications to be used to enable testing of the driver
interface to enable and disable channel switching.
Signed-off-by: Jouni Malinen <j@w1.fi>
Make sure the wmm_ac_status command reflects correctly the existing
tspecs after add_ts/del_ts commands. Add a new test to verify all tspecs
are removed on roaming (while FT is not used).
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
The previous version was enabling all three stations at the same time
and left dev[1] and dev[2] competing on getting connected with dev[0]
that allowed only one pairing. This was not exactly robust and the pass
criteria depended on an extra event from either dev[1] or dev[2]. Fix
that by first connecting dev[0] and dev[1] and only after that, start
dev[2]. This allows proper validation of both the peering limit on
dev[0] and no extra event on dev[2].
Signed-off-by: Jouni Malinen <j@w1.fi>
It is possible for the Probe Response frame wait to time out when active
scanning is used under heavy CPU load. Make this test case more robust
by trying multiple times before declaring the scan for a hidden SSID to
have failed.
Signed-off-by: Jouni Malinen <j@w1.fi>
This allows automated testing of the wpa_supplicant D-Bus interface. The
instance controlling wlan0 registers with D-Bus if dbus-daemon was
started successfully. This is only used in VM testing, i.e., not when
run-tests.sh is used on the host system with D-Bus running for normal
system purposes.
Signed-off-by: Jouni Malinen <j@w1.fi>
wpa_cli and hostapd_cli are not currently tested for code coverage, so
filter the files specific to those components away from the code
coverage reports. *_module_tests.c are not included in normal builds, so
drop them as well. In addition, drop the system header file (byteswap.h)
that gets somehow unnecessarily included in the reports for couple of
lines.
Signed-off-by: Jouni Malinen <j@w1.fi>
This leaves the build tree with valid wpa_supplicant object files in the
end and makes it a bit easier to do additional custom builds when
needed.
Signed-off-by: Jouni Malinen <j@w1.fi>
Previously, these test cases were marked as failures, but it is nicer to
mark as skipped if the kernel does not include support for mesh.
Signed-off-by: Jouni Malinen <j@w1.fi>
Some of the newer dfs_radar* test cases did not allow hostapd
startup to fail. Since these require relatively recent kernel
support, mark the test cases with skip rather than fail based
on that step failing.
Signed-off-by: Jouni Malinen <j@w1.fi>
ap_ht_smps needs relatively recern kernel support, so allow it to be
skipped rather than claimed as failure, in case hostapd startup fails.
Signed-off-by: Jouni Malinen <j@w1.fi>
It was possible for the separate builds to not include
wpa_cli/hostapd_cli in the default location. Make sure hostapd_cli gets
built for --codecov cases and update both WPACLI and HAPDCLI paths to
match the alternative location.
Signed-off-by: Jouni Malinen <j@w1.fi>
Large number of test cases will fail if hostapd fails to start as the
RADIUS server. To make this more obvious, verify that the RADIUS server
instance is running and do not even start test execution if the setup if
not work properly.
Signed-off-by: Jouni Malinen <j@w1.fi>
It was possible for the scr.addstr() operations to fail and terminate
parallel-vm.py if the number of failed test cases increased beyond what
fits on the screen.
Signed-off-by: Jouni Malinen <j@w1.fi>
Wait for a CTRL-EVENT-REGDOM-CHANGE even before returning from
set_country() to avoid issues with test operations being executed before
all components have had chance to update their regulatory domain
information. Some of these test cases could fail under heavy load.
Signed-off-by: Jouni Malinen <j@w1.fi>
Merge partial lines together before processing them in parallel-vm.py.
This avoids issues in cases where the stdout read gets split into pieces
that do not include the full READY/PASS/FAIL/SKIP information. In
addition, strip unnecessary whitespace (mainly, '\r') from the log
lines.
Signed-off-by: Jouni Malinen <j@w1.fi>
parallel-vm.log is now written with details of test execution steps and
results. This makes it easier to debug if something goes wrong in VM
monitoring. The --debug option can be used to enable verbose debugging.
Signed-off-by: Jouni Malinen <j@w1.fi>
parallel-vm.py is now retrying failed cases once at the end of the run.
If all the failed test cases passed on the second attempt, that is noted
in the summary output. Results are also indicated as the exit value from
the run: 0 = all cases passed on first run, 1 = some cases failed once,
but everything passed after one retry, 2 = some cases failed did not
succeed at all.
Signed-off-by: Jouni Malinen <j@w1.fi>
This adds the remaining test cases that took more than 15 seconds to run
into the list of test cases to run at the beginning of the execution to
avoid these being left at the end when only some of the VMs may be
running.
Signed-off-by: Jouni Malinen <j@w1.fi>
Avoid unnecessary DATA_TEST_CONFIG calls and wlantest_cli invocations to
speed up the test cases. This drops ap_qosmap execution time from about
14 seconds to under 3 seconds.
Signed-off-by: Jouni Malinen <j@w1.fi>
There is no need to wait for the longer fixed duration for each STA when
an event message or an earlier wait for another STA can be used instead.
Signed-off-by: Jouni Malinen <j@w1.fi>
Clear cfg80211 BSS table more carefully after the scan_hidden* test
cases. At least scan_hidden_many could have left behind a hidden SSID
entry that could cause problems for following scan_bss_operations test
case.
Signed-off-by: Jouni Malinen <j@w1.fi>
If the initial Authentication frame was too early for the peer (i.e.,
NEW_PEER_CANDIDATE event arrived only after the Authentication frame),
wpas_mesh_open_no_auto and wpas_mesh_secure_no_auto test cases were
failing since they waited only for 10 seconds for the connection to be
completed while the retry timer was set to 10-20 seconds on the
authenticator side.
Signed-off-by: Jouni Malinen <j@w1.fi>
The kernel commit 'packet: make packet_snd fail on len smaller than l2
header' started rejecting <= 14 octet raw packet socket transmission.
This test case was testing with 14 ocets and that is now rejected by the
kernel. While this may be a kernel side issue, use one octet longer test
data for now to avoid undesired FAIL cases in hwsim tests.
Signed-off-by: Jouni Malinen <j@w1.fi>
The previous design did not actually break from the wait loop when the
AP changed back to 40 MHz channel and as such, ended up waiting the full
30 second time. Furthermore, the five second delay time for returning
back to 40 MHz was not sufficiently long to test behavior correctly
since the STA did not have any chances of returning the next coex report
before the AP had returned to 40 MHz. Increase the AP wait time to 15
seconds so that the once per 10 seconds OBSS scan from the STA gets in
before changing back to 40 MHz channel (after the 40 MHz intolerant AP
gets disabled).
Signed-off-by: Jouni Malinen <j@w1.fi>
Use a single iteration through the module dictionary rather than
iterating over the keys and separately fetching values to get the
function.
Signed-off-by: Jouni Malinen <j@w1.fi>
There is no need to wait for one extra second to chown log files when
running as root which is always the case in VM execution.
Signed-off-by: Jouni Malinen <j@w1.fi>
These test cases had a long 120 seconds wait for the GO Negotiation
initiator to time out. This can be done using two devices in parallel to
save two minutes from total test execution time.
Signed-off-by: Jouni Malinen <j@w1.fi>
This function did not seem to do anything else apart from making it less
obvious that hwsim_utils.test_connectivity() is called.
Signed-off-by: Jouni Malinen <j@w1.fi>
Wait one second between each kvm start to avoid hitting large number of
processes trying to start in parallel. This allows the VMs to be started
more efficiently for parallel-vm.py runs with large number of VMs.
Signed-off-by: Jouni Malinen <j@w1.fi>
It was possible for the hidden SSID entry to leak into following test
cases and result in failures, e.g., in this sequence:
scan_hidden
scan_reqs_with_non_scan_radio_work
radius_auth_unreachable
wep_open_auth
BSS <BSSID> picked incorrect BSS entry within wpa_supplicant due to the
old zero-length SSID showing up from the earlier hidden SSID case.
Signed-off-by: Jouni Malinen <j@w1.fi>
Move test cases with long duration to the beginning as an optimization
to avoid last part of the test execution running a long duration test
case on a single VM while all other VMs have already completed their
work.
Signed-off-by: Jouni Malinen <j@w1.fi>
Now there is only one set of commands to maintain. The separate reports
for individual components have not been of much use in the past, so they
are dropped for now.
Signed-off-by: Jouni Malinen <j@w1.fi>
There is no need to wait for the timeout if the ROAM command itself
failed. This could happen if an earlier test case had left hidden SSIDs
in the cfg80211 BSS table.
Signed-off-by: Jouni Malinen <j@w1.fi>
Leaving hidden SSIDs in the cfg80211 BSS table can result in errors in
the following test cases, so use special care to clear all BSS entries
at the end of the wext_hidden test case.
Signed-off-by: Jouni Malinen <j@w1.fi>
This allows code coverage report to be generated must faster with the
help of parallel VMs executing test cases.
Signed-off-by: Jouni Malinen <j@w1.fi>
This verifies that offchannel TX (PD in this specific case) does not
stop ongoing long P2P_LISTEN operation.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
There were couple of typos in the IP addresses and there was no coverage
for the normal unicast ARP response from the bridge (since non-wireless
device does not get proxied by the AP). In addition, it is better to
change the IP address used here to be unique to make the sniffer logs
easier to interpret.
Signed-off-by: Jouni Malinen <j@w1.fi>
This adds transmission of number of NS/NA frames to test ProxyARP
behavior. The actual validation of the AP behavior is still manual,
i.e., a separate inspectation of the capture files is needed.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This may be needed in some corner cases where broadcast frames with two
associated stations are received by both devices.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The final invitation case in this test was verified incorrectly. The GO
was already operatign in that case, so there was not supposed to be a
new P2P-GROUP-STARTED message from GO. That happened to be show up in
the pending event messages from the last instance, but that was just by
accident and any additional dump_monitor() operation added here would
cause this test to fail. Fix this by handling the final invitation
separately and verifying that only the client side indicates
P2P-GROUP-STARTED.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
It is possible for WpaSupplicant instance to be used without the global
control socket, so allow dump_monitor() to handle this case cleanly.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
It was possible for regulatory domain changes to "leak" into following
test cases in number of cases where the cfg80211 BSS table remained
after regulatory domain had been restored to world roaming. Try to make
this less likely to occur by explicitly clearing BSS table at the end of
test cases that use different regulatory domain. This makes P2P test
cases that verify channel selection based on world roaming rules more
robust.
Signed-off-by: Jouni Malinen <j@w1.fi>
It was possible for BSS entries on the scanned channel (2412 MHz) to be
left behind after flush_scan_cache() call. Use a less likely channel
2417 MHz as the default channel to scan. This will hopefully get rid of
most problematic BSS entries from previous test cases. For example,
ap_hs20_oen followed by ap_hs20_random_mac could fail due to
INTERWORKING_CONNECT seeing non-RSN scan result from the previous test
case.
Signed-off-by: Jouni Malinen <j@w1.fi>
This ends up using the special offchannel.c code path where a different
interface is selected for TX. In addition, the P2P-PRESENCE-RESPONSE
event is verified to be delivered on the group interface.
Signed-off-by: Jouni Malinen <j@w1.fi>
The results for these are not currently verified, but this allows
--codecov runs to get more coverage for the command line argument
parsers.
Signed-off-by: Jouni Malinen <j@w1.fi>
This avoids one more cleanup step between most test cases by clearing
the default PMF behavior change only in case it was actually modified
during a test.
Signed-off-by: Jouni Malinen <j@w1.fi>
This avoids one more cleanup step between most test cases by stopping ER
only in case it was actually used during a test.
Signed-off-by: Jouni Malinen <j@w1.fi>
This uses a new testing mode in hostapd to allow RRM neighbor request
transmittion to be tested. For the second part of the test case to be
executed, mac80211_hwsim needs to be modified to claim support for the
required RRM capabilities (that change is not yet in Linux kernel).
Signed-off-by: Jouni Malinen <j@w1.fi>
This verifies processing of various ARP messages at an AP that enables
ProxyARP. All the validation steps have not yet been scripted, i.e., the
sniffer traces need manual analysis for full coverage.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This provides a regression test that would have caught the recent
issue with tls_openssl.c change breaking EAP-FAST.
Signed-off-by: Jouni Malinen <j@w1.fi>
This verifies that the corner case of a duplicated, retransmitted
Invitation Response frame ends up being dropped instead of being
processed twice for the case of Invitation Request getting resend with
social channel as an operating channel in case of no common channels
found.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This adds P2P_SERV_DISC_REQ, P2P_SERVICE_ADD, and P2P_SERVICE_DEL error
cases and P2P_SERVICE_FLUSH and P2P_SERC_DISC_EXTERNAL testing.
Signed-off-by: Jouni Malinen <j@w1.fi>
A single channel scan just before WPS_REG, WPS_PBC, and WPS_PIN commands
can be used to avoid having to run a full scan. This saves significant
amount of time in the WPS test cases.
Signed-off-by: Jouni Malinen <j@w1.fi>
This increases wpa_supplicant_ie_txt(), print_bss_info(), and
wpa_supplicant_ctrl_iface_scan_result() testing coverage to include the
previously missing key management options.
Signed-off-by: Jouni Malinen <j@w1.fi>
This verifies that IBSS_RSN <peer> return OK for the case where a valid
and already connection peer address is given.
Signed-off-by: Jouni Malinen <j@w1.fi>
There is no need to pass the test case names to the VMs when using
parallel-vm.py. Removing those from the command line helps in avoiding
kernel panic if maximum number of kernel parameters limit is hit.
Signed-off-by: Jouni Malinen <j@w1.fi>
Use single channel scan instead of full scan to save time. In addition,
use EAP-GPSK which takes significantly less CPU that EAP-EKE with
default parameters.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This tests RP EAP-Initiate/Re-auth-Start transmission, ERP key
derivation, and EAP-Initiate/Re-auth + EAP-Finish/Re-auth exchange and
rMSK derivation.
Signed-off-by: Jouni Malinen <j@w1.fi>
It was apparently possible for this test case not to do what it was
supposed to do, i.e., get nl80211 Authenticate command failing due to
cfg80211 BS entry missing. With the external radio work blocking fixed,
this can be cleaned up by explicitly waiting for the scan event. In
addition, a less used channel can be selected to avoid finding other BSS
entries.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This makes it more convenient and consistent to clear the cached scan
results from cfg80211 and wpa_supplicant.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Do not leave the station trying to connect at the end of the test case
since that can have an effect to the following test case. Such sequences
should be tested in test cases that are specifically designed for that
rather than randomly between test cases.
Signed-off-by: Jouni Malinen <j@w1.fi>
Since run-tests.py is now required to run as root, there is no need to
use the somewhat awkward "sudo tee" construction; instead, just write
directly to the file.
Signed-off-by: Jouni Malinen <j@w1.fi>
Clear scan results to avoid PBC overlap issues caused by earlier test
cases. For example, go_neg_with_bss_connected followed by
go_neg_with_bss_on_disallowed_chan resulted in failure before this
change.
Signed-off-by: Jouni Malinen <j@w1.fi>
This test case was failing every now and then due to dev1
(no_auto_peer=1) not receiving the new-peer-candidate event in time
before dev0 has already stopped retries on mesh peering open message.
This sounds somewhat expected with the default 4 * 40 ms = 160 ms
retries and 1000 TU beacon interval. Use maximum timeout 16 * 255 ms =
4080 ms to make this test case less likely to fail.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Both the wpa_supplicant and kernel configuration need wext to
run the wext testcase, enable those in the default/example
configurations.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Keep full channel scans in autogo for test coverage, but use single
channel scan in all other autogo* test cases to remove unnecessary
waiting that does not add any test coverage. This removes more than one
minute from the total test execution time.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Replace fixed sleep with waiting for a disconnection event. In addition,
remove unnecessary use of sudo.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
It was possible for this test case to fail due to PBC overlap that was
detected based on previous test case having used PBC. Make that false
positive less likely to happen by explicitly clearing the scan cache on
the device.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
p2p_oper_reg_class and p2p_oper_channel need to be restored to 0, not an
arbitrary 2.4 GHz channel to avoid issues for following test cases. For
example, p2p_channel_random_social_with_op_class_change followed by
p2p_autogo_pref_chan_not_in_regulatory ended up with the latter test
case failing.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
hwsim_utils.test_connectivity() is already bidirectional test, so there
is no need to run it twice with the devices swapped for the second
iteration.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Clear wpa_supplicant and cfg80211 scan results at the end of hidden SSID
test cases to avoid potential issues for following test cases. For
example, ap_hs20_session_info could fail if executed immediately after
ssid_hidden due to the AP configuration change from open to RSN was not
noticed.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This is more robust and extensible than configuring IPv6 addresses on
the interfaces and trying to use ping6 or some other external tools to
generate suitable IPv6 frames.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The 50 ms wait time for Action frame response was not sufficient when
the tests are run under heavy load (e.g., multiple VMs in parallel).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Wait for GO to start before sending invitation frames in the protocol
test. Without this, it was possible to hit the 5 second timeout on
management frame RX under load.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
It was possible for this test case to fail due to PBC overlap that was
detected based on previous test case having used PBC. Make that false
positive less likely to happen by explicitly clearing the scan cache on
the devices.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The "Not fully connected" report did not clearly identify what went
wrong, so make this more verbose in hope of being able to determine what
happened should this test case fail again.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
It was possible to hit the 10 second timeout in some test cases under
heavy load (e.g., with large number of VMs running tests in parallel).
These timeouts are not really indicating any real error, so make them
less likely to show up in reports by increasing the connection timeout
to 30 seconds.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
There are valid status (and possibly status-driver) responses
that don't have a name=value format, ignore those in the test
framework parser.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
It took significant part of the startup latency to prefill the database
with test cases due to the SQL COMMIT operation between each added row.
Move COMMIT to outside the loop to speed startup significantly.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
It can be useful to specify an exact order of test cases and also to
allow the same test case to be run multiple times when the list of tests
is provided on the command line.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
For tests that require a radio with multi-channel concurrency,
create a new one on the fly that does have more than 1 channel.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Newer versions of tshark don't like the -R (read filter) argument
for filtering and just show a deprecation warning. Use -Y (display
filter) instead, which hopefully also works on older versions.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
External tool is not needed anymore to run the data connectivity tests
since hostapd test mode now allows the possible bridge or VLAN interface
to be specified.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
It was possible for some of the SAE test cases (e.g., ap_ft_sae) to fail
if they were run after the sae_groups test case that left the SAE group
configuration to a value that is not enabled by default. Fix this by
clearing sae_groups setting in the couple of test cases that were not
yet doing this.
Signed-off-by: Jouni Malinen <j@w1.fi>
except_ack() was supposed to be verifying that the frame was ACK'ed,
i.e., it was really supposed to be called expect_ack().
Signed-off-by: Jouni Malinen <j@w1.fi>
The implementation of WNM BSS transition management was extended to be
able to return a reject status code based on whether a matching entry is
found. The test case wnm_bss_tm_req was trying to enforce a different
status code to be used here based on old implementation.
Signed-off-by: Jouni Malinen <j@w1.fi>
This implements minimal RSN 4-way handshake Supplicant in Python and
uses that to test hostapd Authenticator implementation in various
possible protocol sequencies.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Change the mesh tests to check for the presence of HT in the scan
results.
[original implementation by Chun-Yeow Yeoh <yeohchunyeow@gmail.com>]
[some fixes by Masashi Honma <masashi.honma@gmail.com>]
Signed-off-by: Ashok Nagarajan <ashok.dragon@gmail.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: Jason Mobarak <x@jason.mobarak.name>
This wpa_supplicant tests include basic tests for:
- Mesh scan
- Mesh group add/remove
- Mesh peer connected/disconnected
- Add/Set/Remove to test mesh mode network
- Open mesh connectivity test
- Secure mesh connectivity test
- no_auto_peer
Signed-off-by: Jason Mobarak <x@jason.mobarak.name>
[no_auto_peer test by: Javier Cardona <javier@cozybit.com>
Signed-off-by: Javier Lopez <jlopex@gmail.com>
The previous changes to enable stdin control broke the previous case of
showing the total number of test cases in the START lines. Fix that by
using a separate variable for the total number of test casess instead of
using length of the list of remaining test cases.
Signed-off-by: Jouni Malinen <j@w1.fi>
This allows all VMs to be used at the end of a test sequence by
assigning test cases to VMs based on which VM is available for a new
test case rather than splitting the full task at the beginning and
potentially getting stuck with the last VM running long test cases for
significantly longer than another VM that gets shorter duration tests
assigned to it.
Signed-off-by: Jouni Malinen <j@w1.fi>
The new -i command line argument can be used to control test case
execution from stdin to run-tests.py and vm-run.sh. This can be used,
e.g., to run multiple repeated test sequences in a virtual machine
without havign to restart the VM between each iteration.
Signed-off-by: Jouni Malinen <j@w1.fi>
Some of the paths in run-tests.py are hardcoded and could not handle
tests/hwsim/vm as the working directory. Modify the design enough to
allow ../run-tests.py -L to be used from the vm directory.
Signed-off-by: Jouni Malinen <j@w1.fi>
This allows a list of matching test cases to be produced without having
to run the test cases. Previously, -L output included all defined test
cases regardless of what else was included on the command line.
Signed-off-by: Jouni Malinen <j@w1.fi>
Previously, it was possible for a kernel panic to be missed since the
only sign of it in stdout was reduced number of passed test cases.
Signed-off-by: Jouni Malinen <j@w1.fi>
This avoids possible mismatches in directory and log file timestamps if
the UNIX timestamp (seconds) changes during the startup sequence.
Signed-off-by: Jouni Malinen <j@w1.fi>
This parameter was used in some of the NFC test cases to make scanning
more robust in case of changing AP configuration. However, the parameter
was not cleared anywhere, so it could have been left in use for other
test cases as well. To get more consistent behavior, clear the value
back to its default between test cases.
Signed-off-by: Jouni Malinen <j@w1.fi>
This was currently breaking parallel-run.*, as it was passing
--split num/num parameters (intended for rnu-tests.py)
to vm-run.sh which broke the --codecov and --timewrap options.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Update the code coverage documentation to also specify the
source base directory for the code coverage generation.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Add an option --build to run-all.sh to build before starting to run all
the tests. In addition, add an option --codecov to extract the code
coverage data at the end of the run.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
This verifies that station mode interface SCAN command gets executed if
P2P Device instance is running p2p_find.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
grpform_cred_ready_timeout2 is similar to the grpform_cred_ready_timeout
test case with the difference being in initiating a P2P_FIND operation
during the wait.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The issue in mac80211 was identified and proposed fix is now available,
so remove the workaround here and start reporting failures from
unexpected disconnection during CSA.
Signed-off-by: Jouni Malinen <j@w1.fi>
This verifies that last_scan_res and connect work pointers to BSS
entries get updated when scan result update ends up removing or
reallocating a BSS entry.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This is needed in preparation for WPS AES being mapped to enabling both
CCMP and GCMP if the driver supports both ciphers.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The new run-tests.py argument "-l <file>" can now be used to specify the
test modules using a text file.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
"./build.sh --force-config" can be used to force copying configuration
files before building. This will overwrite any changes in .config files.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
"./build.sh --codecov" can now be used to request CONFIG_CODE_COVERAGE=y
to be added to hostapd and wpa_supplicant .config files.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
It looks like cfg80211 can trigger disconnection even without disabling
HT, so the same issue may be hit with both of the channel switches in
these test cases.
Signed-off-by: Jouni Malinen <j@w1.fi>
ap_ht40_csa and ap_ht40_csa3 seem to show a cfg80211/mac80211 issue
where a CSA from HT40+ to HT40- channel results in HT getting disabled
due to cfg80211_chandef_compatible() check on c1->width == c2->width
claiming that the new channel is not compatible. For now, comment out
the FAIL case for these known issues to avoid constant failure for cases
that are not wpa_supplicant/hostapd issues. Once the kernel side design
has been reviewed, these error cases can be enabled here.
Signed-off-by: Jouni Malinen <j@w1.fi>
It was possible for the not-pre-authorized GO Negotiation case to end up
starting new GO Negotiation before the GO Negotiation Response frame
with status=1 was transmitted. While this works for group formation, it
could reduce test coverage for the common case where that response is
received. At a small sleep to make it less likely for this unexpected
sequence to happen during testing.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
When loading the hwsim module, disable support_p2p_device by default.
This will also become the default in the kernel, but until then it
makes sure it's not turned on by default.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Use dynamic radios for P2P_DEVICE tests to be able to test
support when the default in hwsim is to not support it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This will be needed to be able to control dynamic mac80211_hwsim
operations like adding and removing a phy. In the past, it has been
possible to start the main programs as root and then use non-root
account for run-tests.py. However, there is already a large number of
cases within the test scripts where sudo is needed. Moving that
requirement to execution of run-tests.py allows those to be simplified
as well.
Signed-off-by: Jouni Malinen <j@w1.fi>
The new HWSimRadio context manager allows the following
syntax to create (and appropriately destroy) a new radio:
with HWSimRadio([...]) as (radio_id, iface_name):
[...]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For testing P2P-Device support properly, allow dynamically
creating radios with support for it in hwsim.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Instead of hardcoding reset_devs() to remove wlan5, remove all wlan*
interfaces renaming in the wpa_supplicant process to support the case of
dynamically added hwsim phy.
Signed-off-by: Jouni Malinen <j@w1.fi>
This replaces use of the external hwsim_test tool for most data
connectivity test cases. Only the cases where a special interface
(bridge/VLAN) is used are still executed through hwsim_test.
The internal DATA_TEST_* functionality makes it easier to extend the
connectivity test cases through an external device with real WLAN
hardware instead of the hwsim test setup. In addition, the error reports
from this code can be made more informative.
Signed-off-by: Jouni Malinen <j@w1.fi>
This makes it easier to use instances of control interfaces in common
code without having to separately address hostapd and wpa_supplicant
behavior differences.
Signed-off-by: Jouni Malinen <j@w1.fi>
This makes it easier to replace data connectivity testing to use
something else than local hwsim_test binary on the controller device.
Signed-off-by: Jouni Malinen <j@w1.fi>
Signed-hostap: Luciano Coelho <luciano.coelho@intel.com>
Skip CSA tests if the driver doesn't support this in AP mode.
Signed-hostap: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
This adds a test which attempts to use the control interface for the
P2P group to remove the P2P group.
Signed-off-by: Toby Gray <toby.gray@realvnc.com>
This is a more advanced version of the simple parallel-vm.sh script.
Status of each VM is printed out during the test and results are
provided in more convenient format in the end.
Signed-off-by: Jouni Malinen <j@w1.fi>
Use scan_for_bss() instead of scan() to avoid errors if the active scan
fails, e.g., due to heavy load under parallel-vm.sh test run.
Signed-off-by: Jouni Malinen <j@w1.fi>
This verifies that GO is able to complete group formation even if the
P2P Client does not send WSC_Done message (or that message is dropped
for any reason) in case the P2P Client completes 4-way handshake
successfully.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
It looks like mac80211 scan-while-associated can now take over 10
seconds with the current wireless-regdb rules for world roaming due to
number of additional DFS channel having been enabled for passive
scanning. This resulted in ap_hs20_session_info failing due to the wait
for the scan result event timing out. That is not really a real failure,
so increase the timeout to avoid reporting this incorrectly.
Signed-off-by: Jouni Malinen <j@w1.fi>
This uses mac80211_hwsim dfs_simulate_radar to get the real kernel side
CAC operation executed and aborted due to radar detection. This allows
another channel to be selected properly through another CAC run.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Simulate a radar detection event to verify that hostapd switches
channels properly and the station follows the AP to the new channel.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
It looks like association with DFS works fine with the current kernel
version, so re-enable this part of the DFS test cases.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Since this requires a recent CRDA version and updated wireless-regdb, do
not report failures yet (i.e., indicate that the test case was skipped
if AP startup fails).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This verifies that hostapd uses Session-Timeout value from Access-Accept
as the lifetime for the PMKSA cache entries and expires entries both
while the station is disconnected and during an association.
Signed-off-by: Jouni Malinen <j@w1.fi>
This reverts commit bf700cc3d2. The
concurrent initialization test case is now expected to work again with
the STA entry added early enough to avoid the recently added mac80211
validation step failure.
Signed-off-by: Jouni Malinen <j@w1.fi>
Older mac80211 implementations did not set the link identifier
appropriately, resulting in an incorrect teardown packet being sent the
peer. wpa_supplicant adds the FTE containing the MIC field calculated
using the correct link-identifier. This causes a MIC failure on the
other side and the teardown is discarded. Verify this case is fixed by
newer kernel and wpa_supplicant code.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Remove and re-start the persistent group manually to increase test
coverage to include the case of re-configuring the PSK list entries from
a stored persistent group.
Signed-off-by: Jouni Malinen <j@w1.fi>
If the previuous test case used a non-RSN AP and that was left in
cfg80211 scan results, it was possible for ap_hs20_random_mac_addr to
pick that old AP from the previous test and reject to connect through
Hotspot 2.0 mechanisms. Work around this test issue by requesting new
set of scan result at the beginning of the test.
Signed-off-by: Jouni Malinen <j@w1.fi>
The scan for WPS-AUTH validation may miss a Probe Response frame if the
hostapd process gets blocked under load, e.g., when testing with
parallel-vm.sh.
Signed-off-by: Jouni Malinen <j@w1.fi>
Previously, periodic autoscan could have been left running and that
could result in the following test cases failing in some cases.
Signed-off-by: Jouni Malinen <j@w1.fi>
Some of the test cases where using INTERWORKING_SELECT internally
without using scan_for_bss like the helper functions did. Add explicit
scan_for_bss calls to make the test cases less likely to fail due to
missing BSSes in scan results. This could cause false failure reports
when runnign under heavy load with parallel-vm.sh.
Signed-off-by: Jouni Malinen <j@w1.fi>
This avoids unexpected connection attempts in cases a matching network
is enabled and there is no existing connection (e.g., when testing with
ENABLE_NETWORK no-connect option).
Signed-off-by: Jouni Malinen <j@w1.fi>
A mac80211 TDLS validation change ended up breaking test functionality
that was needed for this test case. Instead of reporting this known
issue as a FAIL every time, mark the test as SKIP since the issues is
known and there are no plans of "fixing" it.
Signed-off-by: Jouni Malinen <j@w1.fi>
Verify that EAP fast session resumption is skipped if the connection
uses a different network configuration than the last EAP connection.
Signed-off-by: Jouni Malinen <j@w1.fi>
This test case for enforcing the incorrect init=DRIVER instead of
init=CORE for the event due to bug in the event message.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
It was possible for this test case to fail due to PBC overlap that was
detected based on previous test case having used PBC. Make that false
positive less likely to happen by explicitly clearing the scan cache on
dev[1].
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Verify that when all configured preferred channels are disallowed,
the GO is instantiated on a random channel.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Verify that a standalone GO selects a random channel from the social
channels in case no other preference is set.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Verify that when trying to form a P2P group but each peer forces a
different frequency, the group formation fails.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Verify that when setting frequency as no_go_freq and setting up
autonomous GO, the GO is instantiated on a different frequency, but
when forming a P2P group and becoming a client this frequency can be
used.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Verify that when setting up autonomous GO with configured preferred
channel and a station interface is connected on a channel that is
disallowed for P2P, the GO is instantiated on the preferred channel.
Requires MCC.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Verify that when setting up an autonomous GO with configured preferred
channel and a station interface is on another channel, the GO is
instantiated on the same channel as the station interface and not on the
configured preferred channel.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Verify that when a station interface is on one frequency, and GO
negotiation is started in which both sides force a different frequency,
the P2P group is formed on the forced frequency (both as GO and client).
Requires MCC.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
After station interface is connected on a specific channel, create
autonomous GO with forced different channel.
Requires MCC.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Verify that when P2P group is formed and a station interface is
connected on a channel that is disallowed for P2P, the group is formed
on a different channel than the BSS (both as GO and client).
Requires MCC.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Verify that when setting up an autonomous GO and station interface is
connected on a channel that is disallowed for P2P uses, the GO is
instantiated on a different channel than the station mode connection.
Requires MCC.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Verify that when station interface is connected and GO negotiation is
initiated, the P2P group is formed on the same channel as the station
connection.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
This test verifies that if a GO is instantiated after a connection of a
station interface, the chosen operating channel is that of the station
interface.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Add an option to run-all.sh and start.sh to get as an argument the
number of concurrent channels that mac80211_hwsim will be loaded with.
To start mac80211_hwsim with more than one channel, the following
parameter should be added to command line: channels=<num_channels>
The default is one channel (no concurrent channels).
The driver should be loaded with multi channel support in order to run
some tests.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
This test case shows an example case where an uncancelled offchannel TX
frame command seems to end up getting following CMD_FRAME TX operations
transmitting on incorrect channel.
Signed-off-by: Jouni Malinen <j@w1.fi>
This introduces a minimal RADIUS authentication server using pyrad to
allow simple EAP handler functions to be used for writing protocol tests
for EAP peer methods. This initial commit includes test cases for
EAP-SAKE.
Signed-off-by: Jouni Malinen <j@w1.fi>
This is a regression test for printf_encode() bounds checking issues
that can now be caught under valgrind.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Previously, only hostapd-AP and wpa_supplicant processed were run under
valgrind when valgrind testing was enabled. Extend this to include
hostapd as authentication server.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This was still present in hostapd example configuration even though the
test driver wrapper is not used anywhere in the hwsim testing and there
are no plans of using it either.
Signed-off-by: Jouni Malinen <j@w1.fi>
These are similar to the existing test cases where PTK rekey was
triggered by the station, but here a timer on the AP is used as the
trigger.
Signed-off-by: Jouni Malinen <j@w1.fi>
This brings in a minimal pyrad-based RADIUS server to allow various
protocol tests to be run. For now, the server is not adding
Message-Authenticator, so that error case is checked. Additional tests
can be added in the future.
Signed-off-by: Jouni Malinen <j@w1.fi>
This used to result in a segmentation fault due to use of freed memory
(mismatch in pointer lifetime between hostapd.c and driver_nl80211.c).
Signed-off-by: Jouni Malinen <j@w1.fi>
This is a regression test for an issue where scanning sequence could be
terminated if interworking_find_network_match() finds a matching
network, but wpa_s->auto_select is not set. This could stop connection
attempts when auto_interworking=1 is used and the scan results have a
partially matching network and no cred match.
Signed-off-by: Jouni Malinen <j@w1.fi>
radius_{auth,acct}_unreachable tested some parts of RADIUS client code
error handling. However, they did not test everything since the send()
calls for unreachable port on localhost did not return an error (that
error was reported on receive side). Extend this with similar test cases
using unreachable IP address to get send() error returns covered as
well.
Signed-off-by: Jouni Malinen <j@w1.fi>
ap_cipher_tkip_countermeasures_{ap,sta} printed out the MAC addresses in
stdout which resulted in the debug log not starting the PASS/FAIL
information at the beginning of the line. Hide these unnecessary prints
to avoid that.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The example IMV and IMC used for TNC testing has references to
wpa_printf and other functions from hostapd/wpa_supplicant. Link the
binaries in a way that allows these symbols to be resolved while loading
the libraries at run time.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Incorrect password was already tested with TTLS/MSCHAPv2, but the other
non-EAP inner methods in TTLS use their own implementation of password
validation, so check each and also verify the case of no matching EAP
user entry for the specific method.
Signed-off-by: Jouni Malinen <j@w1.fi>
This documents some more steps needed during initial test setup
configuration to make it easier to get this running even without
thorough knowledge of the network setup used by the operating system.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Scan explicitly for the specific AP to work around issues where under
heavy CPU load, the single active scan round may miss the delayed Probe
Response from the AP. In addition, verify that ANQP_GET commands succeed
to make error cases clearer in the log.
Signed-off-by: Jouni Malinen <j@w1.fi>
This verifies that the wait for peer to be ready for GO Negotiation is
timed out properly at no less than 120 seconds. Since this is a long
test case, it is disabled by default without the --long option.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Allow three P2P_FIND attempts for discovering the GO on a non-social
channels since the single Probe Response frame can be missed easily
under heavy CPU load.
Signed-off-by: Jouni Malinen <j@w1.fi>
Scan explicitly for the AP that may be started during the test case
execution. This is needed to work around issues where under heavy CPU
load, the single active scan round may miss the delayed Probe Response
from the second AP.
Signed-off-by: Jouni Malinen <j@w1.fi>
Instead of checking for multiple EAP starts (which can occur if
EAPOL-Start from supplicant goes out quickly enough, e.g., due to CPU
load), look for the explicit message indicating that TTLS method
initialization failed.
Signed-off-by: Jouni Malinen <j@w1.fi>
Scan explicitly for the AP that may be started during the test case
execution. This is needed to work around issues where under heavy CPU
load, the single active scan round may miss the delayed Probe Response
from the second AP. In addition, check for ROAM/FT_DS failures to be
able to report errors more clearly.
Signed-off-by: Jouni Malinen <j@w1.fi>
Scan explicitly for the AP that may be started during the test case
execution. This is needed to work around issues where under heavy CPU
load, the single active scan round may miss the delayed Probe Response
from the second AP.
Signed-off-by: Jouni Malinen <j@w1.fi>
These can fail during heavy CPU load due to active scan dwell time not
being long enough to catch the delayed Probe Response frame from the AP.
Work around this by allowing multiple scan attempts to see the response.
Signed-off-by: Jouni Malinen <j@w1.fi>
There was a bug in this code path that resulted in the
skip-scan-to-start-GO case to not actually skip the scan. It looks like
this could be hit at least when autoscan was enabled, but it is possible
that some other sequences could hit this as well.
Signed-off-by: Jouni Malinen <j@w1.fi>
Since P2P Client scan case is now optimzied to use a specific SSID, the
WPS AP will not reply to that and the scan after GO Negotiation can
quite likely miss the AP due to dwell time being short enoguh to miss
the Beaco frame. This has made the test case somewhat pointless, but
keep it here for now with an additional scan to confirm that PBC
detection works if there is a BSS entry for a overlapping AP.
Signed-off-by: Jouni Malinen <j@w1.fi>
The single channel scan while associated to another AP and immediately
after starting the second AP can miss the Probe Response frame
especially under heavy CPU load. Avoid false error reports by allowing
multiple scan rounds to be performed. wpas_ctrl_bssid_filter is also
modified to take into account different get_bss() behavior.
Signed-off-by: Jouni Malinen <j@w1.fi>
This adds a test case for the server fragmenting an EAP-IKEv2 message.
In addition, the fragmentation threshold is made shorter to trigger
fragmentation for all messages.
Signed-off-by: Jouni Malinen <j@w1.fi>
The BSS id numbers were assumed to start from 0 at the beginning of this
test case, but that is only the case if this is run as the first test
after starting wpa_supplicant. Fix the test case to figure out the id
values dynamically to avoid false errors.
Signed-off-by: Jouni Malinen <j@w1.fi>
Extend EAP-SIM/AKA/AKA' test coverage by setting up another
authentication server instance to store dynamic SIM/AKA/AKA' information
into an SQLite database. This allows the stored reauth/pseudonym data to
be modified on the server side and by doing so, allows testing fallback
from reauth to pseudonym/permanent identity.
Signed-off-by: Jouni Malinen <j@w1.fi>
This allows control interface issues to be caught in a bit more readable
way in the debug logs. In addition, dump pending monitor socket
information more frequently and within each test case in the log files
to make the output clearer and less likely to go over the socket buffer
limit.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
It is possible for the scan to miss a Probe Response frame especially
under heavy load, so try again to avoid reporting invalid failures.
Signed-off-by: Jouni Malinen <j@w1.fi>
It is possible for a scan to fail to see Probe Response or Beacon frame
under heavy load (e.g., during a parallel-vm.sh test run) since the
dwell time on a chanenl is quite short. Make the test cases using
INTERWORKING_SELECT more robust by trying again if the first attempt
does not find a matching BSS.
Signed-off-by: Jouni Malinen <j@w1.fi>
It is possible for the final step of the test case to fail under load
(e.g., when using parallel-vm.sh with large number of VMs), so run
through additional scan iterations if the WPS-AUTH flag does not get
removed immediately.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Verify that AP acts on 40 MHz intolerant STA association/disassociation
and on 20/40 co-ex report indicating 40 MHz intolerant AP showed up and
removed.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
It turned out that the initial test case found the GO based on the
initial full scan instead of the progressive search part. Fix this by
started the GO only after the initial full scan.
Signed-off-by: Jouni Malinen <j@w1.fi>
This can fail if Probe Response frame is missed and Beacon frame was
used to fill in the BSS entry. This can happen, e.g., during heavy load
every now and then and is not really an error, so try to workaround by
runnign another scan.
Signed-off-by: Jouni Malinen <j@w1.fi>
It seems like it is possible for a CTRL-EVENT-REGDOM-CHANGE event from a
previous test case to "leak" through to the execution of this test case.
That can result in the validation steps here failing, so wait a bit and clear the pending events before starting the test.
Signed-off-by: Jouni Malinen <j@w1.fi>
ap_multi_bss_acs test case was failing if it was executed immediately
after a test case that used 5 GHz band since the current mac80211_hwsim
channel survey implementation is very limited and reports only a single
channel. For this test case, that channel has to be from the 2.4 GHz
band.
Signed-off-by: Jouni Malinen <j@w1.fi>
run-tests.py now takes an optional --long parameter that can be used to
enable running of test cases that take a long time (multiple minutes).
By default, such test cases are skipped to avoid making the normal test
run take excessive amounts of time.
As an initial long test case, verify WPS PBC walk time expiration (two
minutes).
Signed-off-by: Jouni Malinen <j@w1.fi>
Do not report missing PBC overlap detection as an issue in this test
case since the sequence can miss the overlap due to per-SSID scan used
during group formation. In addition, increase AP beaconing frequency to
make it more likely for a Beacon frame to be seen during the optimized
scan.
Signed-off-by: Jouni Malinen <j@w1.fi>
This adds some helper definitions and functions to allow cfg80211 to be
tested with raw nl80211 messages built in the test scripts. The first
test case shows a case where station disassociates instead of
deauthenticates (which is the wpa_supplicant behavior).
Signed-off-by: Jouni Malinen <j@w1.fi>
These are similar to the previous cases, but with supported rate set
limited to allow the BSS membership selector to fit into that element
instead of Ext Supp Rates.
Signed-off-by: Jouni Malinen <j@w1.fi>
The 5 GHz cases are not yet complete due to missing mac80211_hwsim
functionality. The current test cases allow the ACS operation to fail
for those cases.
Signed-off-by: Jouni Malinen <j@w1.fi>
This verifies P2P Client scanning behavior during group re-invocation in
a case where old scan results are not available to allow the scan to be
skipped completely.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Wait for the AP to be ready before initiating the scan to avoid
unnecessary five second extra wait. In addition, disconnect the station
to avoid possibility of starting a new scan at the end of the test case.
These remove unnecessary wait time from the test cases.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
"parallel-vm.sh <number of VMs> [arguments..]" can now be used to run
multiple VMs in parallel to speed up full test cycle significantly. In
addition, the "--split srv/total" argument used in this design would
also make it possible to split this to multiple servers to speed up
testing.
Signed-off-by: Jouni Malinen <j@w1.fi>
The optional third argument to the test case functions can now be used
to receive additional parameters from run-tests.py. As the initial
parameter, logdir value is provided so that test cases can use it to
review the debug logs from the test run.
Signed-off-by: Jouni Malinen <j@w1.fi>
Previusly, the responding device was left in p2p_find state as a
consequence of using discover_peer() if the peer was not already known.
This was not the sequence that was supposed to be used here. Go to
listen-only state when waiting for the peer to initiate a previously
authorized GO Negotiation.
Signed-off-by: Jouni Malinen <j@w1.fi>
This was found through a mac80211 bug which didn't correctly accept a
center segment 0 value of zero, so the test will fail until the mac80211
bug is fixed.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This allows a critical error to be noticed more quickly and reported
more clearly in the test log.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Some kernel debugging options (especially
CONFIG_DEBUG_KOBJECT_RELEASE=y) can add significant blocking time to
interface removal with NL80211_CMD_DEL_INTERFACE and
SIOCGIFBR(BRCTL_DEL_BRIDGE) block for 1-8 seconds. This could result in
the VLAN test cases failing due to a wpaspy timeout on the REMOVE
command even though the issue was only in the kernel debugging code
making the operations significantly slower. Work around this by using a
longer timeout for that control interface command to allow this type of
debug kernel to be used.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
If trace-cmd command does not exist, run-tests.py could end up hanging
in a loop waiting for input. Fix this simply by checking whether the
trace-cmd command can be executed sucessfully and exiting the script if
not.
Signed-off-by: Eduardo Abinader <eduardo.abinader@openbossa.org>
Both the output file path and the current working directory included the
log directory and this failed if log directory was not absolute (e.g.,
when using the default logs/current in the case a VM is not used).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The return value was lost and GCMP, CCMP-256, and GCMP-256 test cases
were reporting PASS instead of SKIP.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Verify that session information is stored from Access-Accept and sent to
the station at the requested timeout. Verify that station processes this
notification.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This verifies that hostapd can add extra RADIUS attributes using
radius_auth_req_attr and radius_acct_req_attr.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Fix updating of the current symbolic link when LOGDIR is already set.
The current symbolic link was only set, if LOGDIR has not been
previously defined. If the user had chosen to cancel the running test
iteration and run it again by running start.sh again, the current
symbolic link was not updated.
Signed-off-by: Eduardo Abinader <eduardo.abinader@openbossa.org>
This commit includes number of test frames for attribute parsing.
Invitation Request and Provision Discovery processing is also covered.
Signed-off-by: Jouni Malinen <j@w1.fi>
This is the older design that some drivers may still use if they do not
support offloaded offchannel TX operations.
Signed-off-by: Jouni Malinen <j@w1.fi>
A bit different code path is used to match the first three different
locations of roaming consortium OI within Beacon frame.
Signed-off-by: Jouni Malinen <j@w1.fi>
Wait a bit between WPS_CONFIG command and the first scan. This can avoid
an extra five second wait due to having to scan again if the initial
scan operations happens to be quick enough to happen before the AP has
updated its configuration.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This verifies that 'INTERWORKING_SELECT auto' is able to pick the
correct network based on priority configuration when connected to a
lower priority network.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
test_ap_hs20_multi_cred_sp_prio verifies that two credentials
provisioned by a single SP are selected properly based on sp_priority
when a single BSS matches both credentials.
test_ap_hs20_multi_cred_sp_prio2 does the same when there a separate BSS
for each credential.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This verifies that 'INTERWORKING_SELECT auto' is able to roam to a
higher priority network when executed while connected to a lower
priority network.
Signed-off-by: Jouni Malinen <j@w1.fi>
Add a new option to set the use_chanctx flag when creating a radio.
While at it, refactor the arguments parsing code to use argparse.
Signed-hostap: Luciano Coelho <luciano.coelho@intel.com>
This seems to be needed in some cases to avoid issues in test cases that
assume there are no other ERs running.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This makes the script check the environment for the current python
interpreter in use instead of assuming that the python executable points
to a python 2 interpreter.
Signed-off-by: Roger Zanoni <roger.zanoni@openbossa.org>
Only run-tests.py is actually executed, so there is no need to specify
the interpreter in all the helper files and test script files.
Signed-off-by: Jouni Malinen <j@w1.fi>
CONFIG_MODULE_TESTS=y build option can now be used to build in module
tests into hostapd and wpa_supplicant binaries. These test cases will be
used to get better testing coverage for various details that are
difficult to test otherwise through the control interface control. A
single control interface command is used to executed these tests within
the hwsim test framework. This commit adds just the new mechanism, but no
module tests are yet integrated into this mechanism.
Signed-off-by: Jouni Malinen <j@w1.fi>
Verify cases both with multiple peers (one of which not advertising any
services) and with multiple SD queries.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
It looks like some of the discovery_* test cases have been failing every
now and then on the virtual server and the one second timeout could have
been a bit too short to cover some possible timing cases.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Enable hostapd control interface for the RADIUS server instance and
verify that the RADIUS server MIB counters are incremented.
Signed-off-by: Jouni Malinen <j@w1.fi>
This improves accuracy of the code coverage reports with hostapd-as-AS
and hlr_auc_gw getting analyzed separately.
Signed-off-by: Jouni Malinen <j@w1.fi>
This adds a password that uses one, two, and three octet encoding
for UTF-8 characters. The value is tested against a pre-configured
hash to verify that utf8_to_ucs2() function works correctly.
Signed-off-by: Jouni Malinen <j@w1.fi>
It looks like get_status() has failed in some test runs because of a
STATUS command returning an line without '=' on it. Instead of stopping
there on exception, report the unexpected line in the log and ignore it
to allow test to continue.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This verifies that NFC connection handover can be used in a case where
hostapd has an enabled password token.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Verify that PD Request followed by GO Negotiation Request is enough to
learn the Listen frequency of the peer.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
To test the code under the influence of time jumps, add the option
(--timewarp) to the VM tests to reset the clock all the time, which
makes the wall clock time jump speed up 20x, causing gettimeofday()
to be unreliable for timeout calculations.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
Since wlantest is a separate process that is not synchronized with rest
of the test components, there can be some latency in it having the STA
entries and counters updated. There is a race condition between this
happening and then test script clearing or fetching data. Make this race
condition less likely to cause bogus test failures by adding some wait
between these operations.
Signed-hostap: Jouni Malinen <j@w1.fi>
In addition to running the FLUSH command again, the pending monitor
interface events need be cleared in case the driver was running a scan
when reset() is called. This avoids issues, e.g., with discovery_dev_id
failing due to an unexpected P2P-DEVICE-FOUND event that was generated
by the pending scan operation that had not yet complete when the first
dump_monitor() call in reset() happened.
Signed-hostap: Jouni Malinen <j@w1.fi>
The vm-config in the subdirectory is less useful as it
will get removed by "git clean" and similar, so read a
config file from ~/.wpas-vm-config in addition.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
It looks like slow virtual machines may have issues to complete some EAP
authentication cases (e.g., EAP-EKE in ap_ft_eap) within the 10 second
timeout under load. Double the timeout to avoid incorrect test failures.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
It was possible for the previous test case to leave unexpected BSS or
P2P peer table entries if a scan was in progress when the FLUSH command
was used. This could result in test failures, e.g., when running
discovery_dev_type_go followed by discovery_group_client where a P2P
peer was discovered on another channel at the end of the former test
case from a scan that was running durign the FLUSH operation that was
supposed to remove all P2P peers. This could result in
discovery_group_client failing due to dev[2] trying to send the
discoverability frame on incorrect channel (the one learned in the
previous test case) since discover_peer() skipped a new device
discovery. Fix this by running FLUSH operation again if a pending scan
operation is detected during the first FLUSH operation.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
In addition, add the earlier tests in the new test_ssid.py file that was
forgotten from the previous commit
d78f33030d.
Signed-hostap: Jouni Malinen <j@w1.fi>
WPS-ER-AP-REMOVE event from the ER is sent before HTTP UNSUBSCRIBE has
been completed. As such, it was possible for the following scan
validation step to be started before the AP has had a chance to react to
the ER status change. Makes this less likely to fail by waiting 200 ms
before starting the last scan.
Signed-hostap: Jouni Malinen <j@w1.fi>
It was possible for the AP to report two enrollees in this test case
(i.e., both the expected wlan1 device and also the ER device on wlan0).
The previous test script would fail if the wlan0 device is reported
first. Fix this by allowed the expected target to be found in either the
first or the second WPS-ER-ENROLLEE-ADD event.
Signed-hostap: Jouni Malinen <j@w1.fi>
It was possible for this test case to fail if P2P_FLUSH was issued
during a search scan and that scan adding back the peer. Avoid this by
forcing p2p_find to be started regardless of the current P2P peer table
contents for each round of service discovery.
Signed-hostap: Jouni Malinen <j@w1.fi>
With the extra latencies removed from run-tests.py operations, it was
possible to hit race conditions in pairwise cipher configuration at the
end of the 4-way handshake. In some cases, the EAPOL-Start frame from
the station was not received by the AP and that could result in these
test cases failing. Since there are not really trying to test the race
condition, wait for the AP side to complete key configuration prior to
initiating the reauthentication sequence.
Signed-hostap: Jouni Malinen <j@w1.fi>
When a thread is used to follow P2P group formation progress, it is
better to return a clear failure indication from the thread instead of
allowing an exception to be thrown from the thread.
Signed-hostap: Jouni Malinen <j@w1.fi>
Leave couple of cases to use full scan for better test coverage, but
change all other places to use a single channel scan with
INTERWORKING_SELECT to reduce the time it takes to execute the tests.
Signed-hostap: Jouni Malinen <j@w1.fi>
It is possible that wlantest has not yet created the BSS entry in all
cases, so interpret failures (no BSS entry being the most likely cause)
as zero counters. Similarly, ignore clear_bss_counters errors since they
are most likely reporting that the BSS was not found and as such, there
was no need to clear the counters anyway.
Signed-hostap: Jouni Malinen <j@w1.fi>
The FLUSH command clears disallow_aps, p2p_disabled, and
p2p_per_sta_psk, so there is no need to clear them separately.
Signed-hostap: Jouni Malinen <j@w1.fi>
Replace the fixed 100 ms waits with a select()-based wait and timeout
for full wait based on monotonic time to optimize wait_event().
Signed-hostap: Jouni Malinen <j@w1.fi>
Do not run a full scan in gas_generic since this is not really needed.
Dump pending event messages after long wait to make logs clearer.
Signed-hostap: Jouni Malinen <j@w1.fi>
This makes it easier to build a web page for analyzing failures without
having to fetch the log files themselves from the test server.
Signed-hostap: Jouni Malinen <j@w1.fi>
No need to run a full scan as the first step since it only needs to find
the AP from a known channel for the GAS operation.
Signed-hostap: Jouni Malinen <j@w1.fi>
Now that wpa_supplicant requests the driver (cfg80211) to clear its scan
cache automatically after each BSS_FLUSH/FLUSH command, the previously
used ignore_old_scan_res workaround should not be needed for the hwsim
test cases anymore.
Signed-hostap: Jouni Malinen <j@w1.fi>
This is not really perfect, but something to get a bit more testing
coverage.. For proper discoverability mechanism validation, the P2P
client would need to go to sleep to avoid acknowledging the GO
Negotiation Request frame. Offchannel Listen mode operation on the P2P
Client with mac80211_hwsim is apparently not enough to avoid the
acknowledgement on the operating channel, so need to disconnect from the
group which removes the GO-to-P2P Client part of the discoverability
exchange in practice.
Signed-hostap: Jouni Malinen <j@w1.fi>
It did not look like open mode association completed with WEXT.. I'm
commenting that test case out for now since WPA2-PSK worked. If you care
about WEXT, feel free to fix it and submit a patch to remove the
"REMOVED_" prefix here..
Signed-hostap: Jouni Malinen <j@w1.fi>
Add test cases to use connect command instead of auth+assoc commands and
AP mode operations using the old monitor interface design.
Signed-hostap: Jouni Malinen <j@w1.fi>
The actual data connection does not seem to work with mac80211_hwsim, so
the hwsim_test results are ignored for now.
Signed-hostap: Jouni Malinen <j@w1.fi>
NOTE: Actual use of the direct link (DLS) is not supported in
mac80211_hwsim, so this operation fails at setting the keys after
successfully completed 4-way handshake. This test case does allow the
key negotiation part to be tested for coverage, though.
Signed-hostap: Jouni Malinen <j@w1.fi>
It was previously not obvious from the <test case>.log file that a test
case was marked failed based on kernel issues. Make this very clear to
avoid wasting time on figuring out what caused the failure.
Signed-hostap: Jouni Malinen <j@w1.fi>
Use a more robust design for collecting the gcov logs from the case
where test cases are run within a virtual machine. This generates a
writable-from-vm build tree for each component separately so that the
lcov and gcov can easily find the matching source code and data files.
In addition, prepare the reports automatically at the end of the
vm-run.sh --codecov execution.
Signed-hostap: Jouni Malinen <j@w1.fi>
It takes some time for hostapd to complete AP startup. In some cases,
this could potentially result in station starting a scan before the AP
is beaconing or ready to reply to probes. To avoid such race conditions,
wait for AP-ENABLED before going ahead with the test cases.
Signed-hostap: Jouni Malinen <j@w1.fi>
This makes it easier to enable various testing parameters and
functionality in build configuration.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This adds number of test cases to go through various possible EAP
configurations for Interworking network selection.
Signed-hostap: Jouni Malinen <j@w1.fi>
