If an ER tries to send a message to a STA that is not in the middle
of WPS protocol, do not try to deliver that. This can help with issues
where an ER takes long time to reply to M1 and another Registrar has
already completed negotiation.
It is possible to get a response for a pending EAP callback after the
EAP state machine has already completed its work or has timed out. For
those cases, make sure that the callback function is not delivered since
it could result in NULL pointer dereferences.
The Config Methods attribute in M2 and M2D messages is supposed to
indicate which configuration methods are supported by the Registrar. As
such, it should not depend on whether PBC mode is currently active or
not. That will only affect the Selected Registrar Config Methods and
Device Password ID attributes.
This change is a first step in better supporting different driver
architectures for AP mode operations with nl80211. This commit in
itself does not add new functionality, but it makes it easier to add
new AP mode parameters to address needs of drivers that have more of
the MLME/SME in firmware or kernel.
Split WPA initialization into two parts so that the Beacon frames can be
configured fully before the initial keys (GTK/IGTK) are configured. This
makes it easier for drivers that depend on the AP security mode being
fully set before the keys are configured.
This avoids a request to the driver to first start beaconing before
the WPA/RSN IE has been generated and then immediately changing the
beacon IEs once the WPA/RSN IE is ready.
Such using params->wpa_ie to figure out whether the connection is for
WPA/WPA2 is not correct since that buffer is used also to add WPS IE. In
case of WPS, do not add NL80211_ATTR_WPA_VERSIONS to avoid confusing
drivers.
Some compilers complain about fwrite calls if the return value is
not checked, so check the value even if it does not really make
much of a difference in this particular case.
The internal TLS implementation assumes that the certificate chain
is ordered by issuer certificate following the certificate that it
signed. Add the certificates to the chain in suitable order when
loading multiple certificates.
Commit e1d526293b added code for verifying
whether the receive Probe Request frame was indicating support for only
802.11b rates, but it missed the for loop for the extended supported
rates element. Add that to fix the validation code for cases where
non-802.11b rates are in the extended supported rates element.
Currently, wpa_driver_nl80211_authenticate() changes the interface type
to station. However, in case of P2P, we need to change the interface
type to P2P_CLI.
Add p2p field to the authentication params, and consider it for choosing
the correct interface type.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Commit 9f51b11395 added support for P2P
interfaces when adding a new interface. However, it didn't handle the
case in which the same interface is being used and its type is being
changed. Add support for this case.
Consequently, when doing "ap_scan_as_station" we now need to save the
actual AP interface type (AP/P2P GO) in order to restore it properly.
For that, change ap_scan_as_station type from int to nl80211_iftype, and
set it to NL80211_IFTYPE_UNSPECIFED when not used.
Signed-off-by: Eliad Peller <eliad@wizery.com>
When driver_nl80211.c has to set the netdev down to change iftype, an
RTM_NEWLINK event is generated. Do not generate
EVENT_INTERFACE_DISABLED event based on that.
Reassociation Request/Response frame validation need to count all IEs in
the RIC. In addition, TIE is not protected, so it should not be included
in the count.
Signed-off-by: Hong Wu <hong.wu@dspg.com>
Only accept Probe Request frames that have a Wildcard BSSID and a
destination address that matches with our P2P Device Address or is the
broadcast address per P2P specification 3.1.2.1.1.
When a new interface is created and already has a separate MAC address
assigned by the kernel, then we need to use that address, not just when
we've created a locally administered address.
This fixes use_p2p_group_interface=1 for iwlagn as it already makes
mac80211 assign an address for a second interface since the hardware has
two addresses assigned.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add support to wpa_supplicant for device-based GTK rekeying. In order to
support that, pass the KEK, KCK, and replay counter to the driver, and
handle rekey events that update the latter.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Send STA flags to kernel when adding a new station. This ensures
stations are added with up to date flags by kernel drivers.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
When adding a new station, set the STA flags as part of the sta_add()
command. This ensures the flags are up to date when the station is added
by lower level drivers.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
A new hostapd configuration parameter, disable_pmksa_caching=1, can now
be used to disable PMKSA caching on the Authenticator. This forces the
stations to complete EAP authentication on every association when WPA2
is being used.
In general, this patch attemps to extend commit
00468b4650 with dbus support.
This can be used by dbus client to implement subject match text
entry with preset value probed from server. This preset value, if
user accepts it, is remembered and passed to subject_match config
for any future authentication.
Signed-off-by: Michael Chang <mchang@novell.com>
Data path is broken when hostapd reloads its configuration
disabling the security which was previously enabled (WEP/WPA),
using kill -1, as old keys were not cleared.
The patch clears the keys configured when hostapd reloads
its configuration.
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
This phase1 parameter for TLS-based EAP methods was already supported
with GnuTLS and this commit extends that support for OpenSSL and the
internal TLS implementation.
Fix a bug with the current dev_found()/dev_lost() usage. Previously
in p2p_device_free() dev_lost() was invoked for devices that had
not been dev_found(). This caused dbus related msgs to stderr like:
"Attempted to unregister path (path[0] = fi path[1] = w1) which isn't
registered"
Signed-off-by: Angie Chinchilla <angie.v.chinchilla@intel.com>
Some P2PDevice properties were not updated in p2p->cfg structure:
reg_class, channel, op_reg_class, and op_channel. Hence, update p2p->cfg
parameters through p2p core calls in wpas_p2p_update_config().
Signed-off-by: Jean-Michel.Bachot <jean-michelx.bachot@intel.com>
Signed-off-by: Jayant Sane <jayant.sane@intel.com>
Move level parameter from p2p_device to p2p_device_info in order to
expose this information and modify D-Bus P2P handler to return this new
parameter through the P2P device properties.
Signed-off-by: Fabien Marotte <fabienx.marotte@intel.com>
Signed-off-by: Jayant Sane <jayant.sane@intel.com>
Previously hostapd just masked the STAs HT caps with its own. However,
some HT caps are not symmetric and as such need to be handled
different.
hostapd shouldn't overwrite the STAs SMPS mode as otherwise the driver
cannot know it has to use RTS/CTS to wake the receiver from dynamic
SMPS for MCS rates > 7.
hostapd shouldn't mask the RX and TX STBC caps with it's own. They are
already handled in a special case below.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
This file is a part of the radiotap parser that Andy Green agreed to
relicense under the BSD license (per email, 11 Aug 2007 07:42:05
+0100). The copyright/license statement was updated in radiotap.c,
but this radiotap_iter.h file was forgotten at that point.
In set_key handler, the seq[8] is in little endian order defined by
WPA. BSD kernel uses a u_int64_t value ik_keyrsc to represent it
internally. The kernel expects the native endian order for the value.
Thus, we need to detect the endian order and swap bytes when
necessary.
This fixes an issue with SA Query Response frames not being processed
anymore after wpa_supplicant started registering a handler for those.
This handler registration is in generic driver_nl80211.c code, so
hostapd uses it, too.
Implement PMKSA cache operations add, remove, and flush using nl80211
commands NL80211_CMD_{SET,DEL,FLUSH}_PMKSA to support PMKSA caching
with drivers that select the AP and generate the RSN IE internally.
When provision discovery fails, this new callback will be called
so P2P users can react to the failure.
Signed-off-by: Jayant Sane <jayant.sane@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since the peer may not be in Listen state when the provision discovery
request is sent, try to send the request again number of times when in
IDLE state. This was already done when p2p_find is in progress, but this
commit adds retries to the case where no other P2P operations are in
progress.
Signed-off-by: Jayant Sane <jayant.sane@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This can be used to avoid rejection of first two 4-way handshakes every
time hostapd (or wpa_supplicant in AP/IBSS mode) is restarted. A new
command line parameter, -e, can now be used to specify an entropy file
that will be used to maintain the needed state.
Some of these are required for proper functionality (like
get_seqnum); others may not be needed yet, but including them
allows some extra ifdef/endif blocks to be removed.
.set_rate_sets is not defined for non-hostapd, which prevents
configuring basic_rates when working as P2P GO.
Signed-off-by: Eliad Peller <eliad@wizery.com>
If the driver wrapper is setting up the interface up only at commit(),
UPnP initialization fails. Fix that by moving UPnP setup to happen after
the driver commit() call.
Windows 7 uses incorrect way of figuring out AP's WPS capabilities by
acting as a Registrar and using M1 from the AP. The config methods
attribute in that message is supposed to indicate only the configuration
method supported by the AP in Enrollee role, i.e., to add an external
Registrar. For that case, PBC shall not be used and as such, the
PushButton config method is removed from M1 by default. If pbc_in_m1=1
is included in the configuration file, the PushButton config method is
left in M1 (if included in config_methods parameter) to allow Windows 7
to use PBC instead of PIN (e.g., from a label in the AP).
cfg80211 maintains separate BSS table entries for APs if the same
BSSID,SSID pair is seen on multiple channels. wpa_supplicant does
not use frequency as a separate key in the BSS table, so filter out
duplicated entries. Prefer associated BSS entry in such a case in
order to get the correct frequency into the BSS table.
It may take some time for the TX status to be delivered for a
(Re)Association Response frame and if any Data frames are received
during that time, they may end up getting dropped as Class 3 frames in
not-associated state. This results in a Disassociation frame being sent
to the station and it assuming that the association has been lost.
Work around the issue by remembering that the (Re)Association Request
has already been accepted and skip the Deauth/Disassoc sending because
of the possible Class 3 frames before the TX status callback is
received.
In theory, these calls could fail, but it is not really likely to
happen in practice in the use case here. Anyway, check that they do
not return an error before accepting the length of the file.
This function does not get called with in_data == NULL in practice, but
it seems to be at least partly prepared for that case, so better make it
consistent by handling the NULL value throughout the function.
Both the SA and IEs from the received Probe Request frames must be
included and the Probe Request RX callback functions may assume that
these are not NULL.
The change to use wpa_dbg() in wpa_sm_parse_own_wpa_ie() could result
in a NULL pointer dereference if the function were called when WPA
state machine has not been initialized. While this cannot really
happen in practice, it is better to be prepared for that since that
was the case before the wpa_dbg() change.
The size_t value here can be 64-bit and result in implicit sign
extension. In this particular case, that gets masked out by
host_to_be32(), so there is no practical difference, but it is better
to get rid of the 64-bit variable explicitly.
The supportedTypes parameter is a list of TNC_MessageType values
and the buffer to be copied should use size of TNC_MessageType, not
TNC_MessageTypeList. In practice, these are of same length on most
platforms, so this is not a critical issue, but anyway, the correct
type should be used.
This avoids reading past the end of the IE buffer should the FTIE
be too short. In addition, one debug hexdump was using uninitialized
pointer to the FTIE buffer, so fixed it to use the pointer from the
parse data.
AF_INET6 is not always enabled by default, so use AF_INET instead. In
addition, use the old fixed length, 2048, as a failover value if the
sysctl fails for any reason.
Commit 03d3f28a69 broke initialization of
EAPOL authenticator state machines since an error value from
wpa_auth_sta_key_mgmt() (-1) was not handled properly and the fixed
wpa_key_mgmt_wpa_psk() identified the value as a PSK-based AKM because
of all bits being set to 1. The special error value needs to handled
separately to avoid skipping EAPOL state machine initialization.
These can be used in some cases with a bitfield having multiple
AKMs enabled (e.g., WPA-PSK and WPA-PSK-SHA256). Address those
cases by checking whether any of the matching AKM are included.
When the SME is in the driver or cfg80211, the automatic selection
of auth_alg is done by leaving out the NL80211_ATTR_AUTH_TYPE
attribute from the NL80211_CMD_CONNECT command.
This should fix EAPOL reauthentication and rekeying timeout issues
with Intel clients when using WMM (e.g., with IEEE 802.11n). These
stations do not seem to be able to handle EAPOL data frames as
non-QoS Data frames after the initial setup.
This adds STA flags to hapd_send_eapol() driver op to allow
driver_nl80211.c to mark the EAPOL frames as QoS Data frame
when injecting it through the monitor interface.
This provides a means for the supplicant to directly request signal
quality metrics from the driver. This is useful, for example for
background scan algorithms that might ask desire this information
out-of-band with CQM events.
Signed-off-by: Paul Stewart <pstew@google.com>
When building IE from an empty string and CONFIG_WPS_STRICT is
not defined, redundant 2 bytes are being added to the string.
We have to return right after building the "dummy" string.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Some deployed supplicants update their SNonce for every receive
EAPOL-Key message 1/4 even when these messages happen during the
same 4-way handshake. Furthermore, some of these supplicants fail
to use the first SNonce that they sent and derive an incorrect PTK
using another SNonce that does not match with what the authenticator
is using from the first received message 2/4. This results in
failed 4-way handshake whenever the EAPOL-Key 1/4 retransmission
timeout is reached. The timeout for the first retry is fixed to
100 ms in the IEEE 802.11 standard and that seems to be short
enough to make it difficult for some stations to get the response
out before retransmission.
Work around this issue by increasing the initial EAPOL-Key 1/4
timeout by 1000 ms (i.e., total timeout of 1100 ms) if the station
acknowledges reception of the EAPOL-Key frame. If the driver does
not indicate TX status for EAPOL frames, use longer initial
timeout (1000 ms) unconditionally.
Store Manufacturer, Model Name, Model Number, and Serial Number
attributes for P2P peers and expose these through the existing
peer information mechanisms.
Previously, a bug in GKeyDoneStations count would remain in effect
until the authenticator is restarted. Make this more robust by
clearing the station count before each rekeying setup. While this
is not really supposed to be needed, there has been bugs in this
area in the past and it is safer to make the implementation recover
from such an issue automatically.
If the STA to be freed is still included in GKeyDoneStations count,
decrement the count when the STA is freed. This does not happen in
AP mode since there is enough time to go through the authenticator
state machine to clear the STA. However, in the current RSN IBSS
implementation, the authenticator state for the STA is freed in a
way that does not allow the state machine to go through the clearing.
To address this, make sure that wpa_free_sta_sm() decrements the
GKeyDoneStations count if the STA happened to be in the process of
GTK rekeying.
CFLAGS += -DCONFIG_RSN_TESTING in .config and rsn_testing=1 in
hostapd.conf can now be used to enable a testing mode that adds
extensions to RSN element. This can be used to check whether
station implementations are incompatible with future extensions
to the RSN element.
The AP code might, currently only in the case of HT40, defer actual
enabling to after a scan. In this case, the wpa_s AP code gets confused.
Add a callback for it to use and make it use it to finish only when the
setup has actually completed.
With appropriate hacks in place this allows using HT40 in P2P mode.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Make the P2P code keep track of WPS vendor extensions received from
peers so they can be exposed via DBus later.
Signed-off-by: Jean-Michel Bachot <jean-michelx.bachot@linux.intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This adds the ability to add WPS vendor extension attributes in P2P
frames, like GO Negotiation and Probe Response frames.
Signed-off-by: Jean-Michel Bachot <jean-michelx.bachot@linux.intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This adds the ability to add WPS vendor extensions to an AP (or GO).
They will be added to the WSC IE(s) in Beacon and Probe Response frames.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Instead of converting back and forth from the string representation,
always use the binary representation internally.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Use only the UUID-E to remove active PBC session(s) at the completion of
successful PBC protocol run. This fixes potential issues with Enrollees
that use multiple MAC addresses and as such, can get multiple entries in
the PBC session list.
Add Secondary Device Type List attribute in WSC IE for P2P
Probe Response frames if one or more secondary device types
are configured.
Signed-off-by: Jean-Michel Bachot <jean-michelx.bachot@linux.intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The secondary device type list is an optional attribute in the WSC IE.
Signed-off-by: Jean-Michel Bachot <jean-michelx.bachot@linux.intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently hostapd will force HT Mixed Mode if at least one non-GF STA is
associated. This will force _all_ HT transmissions to be protected.
802.11n-2009 doesn't require HT Mixed Mode to be used in case of non-GF
STAs but instead the HT information element contains a flag if non-GF
STAs are present. All STAs are required to protect GF transmissions in
that case. Hence, setting HT Mixed mode if non-GF STAs are present is
superfluous.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Use a specific return value, WPS-PBC-OVERLAP, to indicate a reason
for rejecting a wps_pbc command in wpa_supplicant AP mode if the
PBC mode cannot be started due to PBC session overlap having been
detected during monitor time.
This allows the user to complete WPS provisioning using PBC by
selected a specific Enrollee even if there are other Enrollees
in active PBC mode at the same time. The other Enrollees will be
rejected should they try to connect at the same time.
Ignore possible mismatches in the source address of the frame and only
use UUID-E to check whether a Probe Request or M1 is from the same
Enrollee when figuring out whether there is PBC session overlap. This
is needed to avoid potential issues with Enrollee devices that may have
multiple interfaces indicating active PBC state.
If there is already a link the requested peer, request start of
renegotiation instead of completely new link. This seems to be needed
to allow some driver to accept the trigger for a new negotiation.
tdls_testing 0x80 can now be used to request wpa_supplicant to send
a TDLS Setup Request frame (i.e., try to initiate TDLS setup)
whenever a TDLS Setup Request frame has been received from a peer.
Blindly clearing all struct wpa_tdls_peer members is a risky
operation since it could easily clear pointers to allocated
memory, etc. information that really should not be removed.
Instead of hoping that new code gets added here to restore
the important variables, reverse the approach and only clear
structure members one by one when needed.
This allows the same code path to be used for both protected and
unprotected configurations to limit need for duplicated code in
both the driver and wpa_supplicant.
This adds code for validating that the same Key Lifetime is used
throughout TPK handshake and enables TPK lifetime expiration and
renewal/teardown. These part seem to be working, but the actual
handling of TDLS Setup Confirm and renewal are not fully
functional yet.
tdls_testing bits:
bit 3 = use short TPK lifetime (301 seconds)
bit 4 = use wrong TPK lifetime in TDLS Setup Response
bit 5 = use wrong TPK lifetime in TDLS Setup Confirm
These special test cases can be configured at run time with "wpa_cli
tdls_testing <value>" where <value> is an integer (either as a decimal
or as a hex value with 0x prefix) bitmap of special features with
following bits available at this point:
bit 0 = long frame (add dummy subelement to make FTIE very long)
bit 1 = use alternative RSN IE (different RSN capab value and no extra
replay counters)
bit 2 = send incorrect BSSID in Link Identifier of TDLS Setup Request
(e.g., 1 = long FTIE, 2 = different RSN IE, 3 = both of those)
This is disabled by default and can be enabled for the build by
adding the following line to .config:
CFLAGS += -DCONFIG_TDLS_TESTING
This allows driver wrappers to indicate whether the association was
done using Association Request/Response or with Reassociation
Request/Response frames.
CFLAGS += -DCONFIG_VALGRIND can now be used to enable support for
Valgrind client requests to help in removing some non-issues from
Valgrind reports. This is mainly aimed at allowing unknown ioctl
results to be marked as defined data.
If the os_time_t variable used for the expiration time (seconds)
overflows when the registered timeout value is being added,
assume that the event would happen after an infinite time, i.e.,
would not really happen in practice. This fixes issues with
long key timeouts getting converted to immediate expiration due
to the overflow.
os_snprintf() can be a preprocessor macro and according to
C99 (6.10.3 clause 11) the results of having preprocessor directives
inside the macro arguments is undefined.
Build options can now be used to replace the location of client
sockets for UNIX domain socket control interface:
CFLAGS += -DCONFIG_CTRL_IFACE_CLIENT_DIR=\"/tmp\"
CFLAGS += -DCONFIG_CTRL_IFACE_CLIENT_PREFIX=\"wpa_ctrl_\"
The buffer size for routing socket is fixed to 2048.
This patch fix it to obtain the size from OS.
This patch worked on x86 platform with NetBSD 5.0.2.
This allows keystore:// prefix to be used with client_cert and
private_key configuration parameters.
Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
This will only retrieve information about peers that have been fully
discovered, not peers that are only half-discovered based on their Probe
Request frames.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The DBus code will want to have perfect matching of dev_found and the
dev_lost it adds so it doesn't need to keep track internally. Enable
that with a new flag in the core that tracks whether we have already
notified about this -- the existing users can ignore it.
The part where this is always set to 1 if the new device is discovered
by a driver that has P2P in the driver is buggy -- the driver should
feed the P2P peer database and then that should feed the notification
here instead.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This embeds some information about each P2P peer that will be publically
visible in a struct that is shared.
The dev_found notification function is also passed the new struct, which
requires some work for the driver-based P2P management.
Signed-off-by: Konguraj(Raj) Kulanthaivel <konguraj.kulanthaivel@intel.com>
Signed-off-by: Fabien Marotte <fabienx.marotte@linux.intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When using multiple vifs and dynamic vlan tagging is enabled on any
interface, the created AP VLAN interfaces get the BSSID of the first
AP mode interface instead of the BSSID of the corresponding AP mode
interface.
Example:
wlan0 - xx:xx:xx:xx:x0
wlan1 - xx:xx:xx:xx:x1
Assume a STA connects to the AP interface wlan1 and gets a dynamic
VLAN tag 100 assigned by the RADIUS server. Hostapd will create an AP
VLAN interface wlan1.100 but doesn't set an address for this interface
which results in wlan1.100 getting the same address as wlan0:
wlan1.100 - xx:xx:xx:xx:x0
As a result the STA that was moved to wlan1.100 isn't able to finish its
4-way handshake since mac80211 won't pass its frames to wlan1.100 due to
the different address.
To fix this issue make use of the address of the AP interface when
creating an AP VLAN interface.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Add MAC addresses for stations and use wpa_msg instead of printf
methods to make it easier to grep logs and find messages for the
station in question.
Signed-off-by: Ben Greear <greearb@candelatech.com>
If parsing of the certificate or private key succeeds using any of
the tried encoding types, clear the OpenSSL error queue without
showing the pending errors in debug log since they do not really
provide any useful output and can be confusing.
This patch fixes a problem I had when I tried to connect
an embedded system [wpa_supplicant, CONFIG_TLS=internal]
to my TLS secured network.
TLSv1: Send CertificateVerify
TLSv1: CertificateVerify hash - hexdump(len=36): ha .. ha
PKCS #1: pkcs1_generate_encryption_block - Invalid buffer lengths \
(modlen=512 outlen=454 inlen=36)
It turned out that a fixed 1000 byte message buffer was just
a little bit too small for the 4096 bit RSA certificates
I'm using.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
In multi BSS setups it wasn't possible to set up an HT BSS in
conjunction with a WEP/TKIP BSS. HT needed to be turned off entirely
to allow WEP/TKIP BSSes to be used.
In order to allow HT BSSes to coexist with non-HT WEP/TKIP BSSes add a
new BSS conf attribute "disable_11n" which disables HT capabilities on a
single BSS by suppressing HT IEs in the beacon and probe response
frames. Furthermore, mark all STAs associated to a WEP/TKIP BSS as
non-HT STAs. The disable_11n parameter is used internally; no new entry
is parsed from hostapd.conf.
This allows a non-HT WEP/TKIP BSS to coexist with a HT BSS without
having to disable HT mode entirely. Nevertheless, all STAs associated to
the WEP/TKIP BSS will only be served as if they were non-HT STAs.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Use l2_packet with Ethernet header included so that the source
address for RRB packets can be forced to be the local BSSID. This
fixes problems where unexpected bridge interface address may end
up getting used and the recipient of the frame dropping it as
unknown R0KH/R1KH.
This is needed to keep kernel and hostapd in sync. In addition,
the obsolete entry in hostapd prevented use of Deauthentication
or Disassociation frame with reason code 6/7 mechanism to indicate
to the STA that there is no association if the STA missed the
broadcast Deauthentication frame for any reason.
The internal pointer to RADIUS client configuration needs to be
updated whenever a new hostapd configuration is loaded. Without
this, freed memory may be dereferenced and this can result in
segmentation faults.
This converts number of debugging messages to use wpa_msg() in order
to allow the interface name to be shown with the messages.
A new function, wpa_dbg(), is introduced to allow
CONFIG_NO_STDOUT_DEBUG=y builds to remove the debug strings. This is
otherwise identical with wpa_msg(), but it gets compiled out if stdout
debugging is disabled.
This is needed to allows WPS PBC session overlap detection to work
with drivers that process Probe Request frames internally. This
code is is run in hostapd, but the wpa_supplicant AP mode did not
have call to the hostapd_probe_req_rx() function even though it
registered handlers for hostapd Probe Request RX callbacks.
An optional parameter, p2p_dev_addr, can now be given to WPS_PBC
command on P2P GO to indicate that only the P2P device with the
specified P2P Device Address is allowed to connect using PBC. If
any other device tries to use PBC, a session overlap is indicated
and the negotiation is rejected with M2D. The command format for
specifying the address is "WPS_PBC p2p_dev_addr=<address>", e.g.,
WPS_PBC p2p_dev_addr=02:03:04:05:06:07
In addition, show the PBC session overlap indication as a WPS failure
event on an AP/GO interface. This particular new case shows up as
"WPS-FAIL msg=4 config_error=12".
This makes log files much more readable if multiple interfaces
are being controlled by the same process. The interface name is
added to stdout/file/syslog entries, but not to the messages
sent to control interface monitors to avoid issues with parsing
in external programs.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Add a callback for station's authorized transitions
to allow wpa_supplicant to emit events in DBus.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
To enable making state change notifications on the WLAN_STA_AUTHORIZED
flag, introduce ap_sta_set_authorized(), and to reduce use of the flag
itself also add a wrapper for testing the flag: ap_sta_is_authorized().
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If the driver advertises max_remain_on_chan data, use it instead of
the hardcoded value of 5000. Keep the default at 5000 since that is the
value used by earlier versions of cfg80211/mac80211 and not advertised
in nl80211 for those.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When authenticating, and the interface type is not already
NL80211_IFTYPE_STATION, we need to call wpa_driver_nl80211_set_mode()
only once. Remove the excessive call.
Signed-off-by: Eliad Peller <eliad@wizery.com>
We need to call this function after having completed the neighboring
channel scan to figure out whether HT40 can be used and if so, which
channel is the secondary channel.
ieee80211n_supported_ht_capab is called after ieee80211n_check_40mhz in
function hostapd_check_ht_capab. ieee80211n_check_40mhz can return 1 in
a valid scenario where the initialization is completed in a callback. In
this case ieee80211n_supported_ht_capab is skipped and hostapd does not
check the ht capabilities reported by the driver. Fix this issue making
sure ieee80211n_supported_ht_capab gets called.
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
If WMM is not disabled explicitly (wmm_enabled=0 in hostapd.conf),
enable WMM automatically whenever HT (ieee80211n) is enabled. Use
the default WMM parameters for AP TX queues and the EDCA parameters
advertised for stations in WMM IE if no overriding values are
included in the configuration.
We can use the P2P interface types to check if the driver supports P2P
and to tell the kernel that a given interface is going to be used for
P2P (when it is created).
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There is no real reason to maintain these in the current development
branch anymore. If someone really needs support for the obsolete
driver interfaces, these can be found in older wpa_supplicant
branches.
driver_atmel.c
- vendor-specific interface for ATMEL AT76C5XXx cards
- for some old out-of-tree driver; not for the upstream atmel*
drivers
driver_ndiswrapper.c
- vendor-specific interface for an out-of-tree driver
- ndiswrapper should work with driver_wext.c, too
driver_ipw.c
- vendor-specific interface for old ipw2100/2200 driver
- the upstream driver works with driver_wext.c (and does not work
with the old interface)
driver_hermes.c
- vendor driver that was not even included in the main wpa_supplicant
releases
In order to enable protection mechanisms for different HT opmodes the
driver needs to be aware of the current HT opmode that is calculated by
hostapd. Hence, pass the current opmode to the nl80211 driver via
the bss attribute NL80211_ATTR_BSS_HT_OPMODE.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
tdls_prohibit=1 and tdls_prohibit_chan_switch=1 and now be used to
disable use of TDLS or TDLS channel switching in the BSS using
extended cabilities IE as defined in IEEE 802.11z.
Make sure that received management frames are long enough before
processing them. This avoids a potential segmentation fault if a
driver delivers an invalid frame all the way to hostapd.
The changes are:
1. the word "and" in the hunting-and-pecking string passed to the KDF
should be capitalized.
2. the primebitlen used in the KDF should be a short not an int.
3. the computation of MK in hostap is based on an older version of the
draft and is not the way it's specified in the RFC.
4. the group being passed into computation of the Commit was not in
network order.
Previously, only the Configuration Error values were indicated in
WPS-FAIL events. Since those values are defined in the specification
it is not feasible to extend them for indicating other errors. Add
a new error indication value that is internal to wpa_supplicant and
hostapd to allow other errors to be indicated.
Use the new mechanism to indicate if negotiation fails because of
WEP or TKIP-only configurations being disallows by WPS 2.0.
This needs to be done both in the more normal location in
p2p_timeout_connect_listen() (internal timeout after driver event) and
in p2p_listen_end() as a workaround for the case where the driver event
is delayed to happen after the internal timeout.
Previously, both NULL and ff:ff:ff:ff:ff:ff addr were used in various
places to indicate default/broadcast keys. Make this more consistent
and useful by defining NULL to mean default key (i.e., used both for
unicast and broadcast) and ff:ff:ff:ff:ff:ff to indicate broadcast
key (i.e., used only with broadcast).
When hostapd is removing a virtual BSS interface, the loop here was
incorrectly not updating the iterator during list traversal and
ended up in an infinite loop in some cases.
Use NULL instead of (u8 *) "" as the seq value and make sure the
driver wrapper implementations can handle NULL value. This was
previously already done in number of places, but not everywhere.
wpa_supplicant seems to crash from time to time on a NetBSD 4.0 MIPS
platform. The root cause turned out to be a MIPS alignment issue.
In my wpa_supplicant crash case, in function
wpa_driver_bsd_event_receive (from driver_bsd.c), the buf[2048] address
is started from i.e. 0x7fffd546, which is not 4 bytes aligned. Later
when it is casted to (struct if_msghdr *), and rtm->rtm_flags is used.
rtm->rtm_flags is "int" type, but its address is not 4 bytes aligned.
This is because the start address of rtm is not 4 bytes aligned.
Unfortunately in NetBSD MIPS kernel (unlike Linux MIPS kernel emulates
unaligned access in its exception handler), the default behavior is to
generate a memory fault to the application that accesses unaligned
memory address. Thus comes the early mentioned wpa_supplicant crash. An
interesting note is when I'm using the wpa_supplicant version 0.4.9, I
never saw this problem. Maybe the stack layout is different. But I
didn't look into details.
I used below patch to resolve this problem. Now it runs correctly for at
least several hours. But you might have a better fix (maybe we can use
malloc/free so that it is at least cache line aligned?). I'm also not
sure if other drivers should have the same problem.
This adds partial callbacks and events to allow P2P management to be
implemented in a driver/firmware. This is not yet complete and is
very much subject to change in the future.
CONFIG_WPS_REG_DISABLE_OPEN=y can be used to configure wpa_supplicant
to disable open networks by default when wps_reg command is used to
learn the current AP settings. When this is enabled, there will be a
WPS-OPEN-NETWORK ctrl_iface event and the user will need to explicitly
enable the network (e.g., with "select_network <id>") to connect to
the open network.
If the underlying driver supports off-channel TX, it will now be used by
the nl80211 driver wrapper, setting WPA_DRIVER_FLAGS_OFFCHANNEL_TX
accordingly.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
With the new kernel functionality coming to Linux to allow off-channel
TX, we can take advantage of that in the P2P code that currently uses
remain-on-channel. If a driver advertises support for it, it will be
asked to handle off-channel TX by itself.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The nl80211 driver can report low ACK condition (in fact it reports
complete loss right now only). Use that, along with a config option, to
disconnect stations when the data connection is not working properly,
e.g., due to the STA having went outside the range of the AP. This is
disabled by default and can be enabled with disassoc_low_ack=1 in
hostapd or wpa_supplicant configuration file.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
ClientTimeout changes from EAP peer methods were not supposed to
change behavior for other EAP peer methods or even other sessions
of the same method. Re-initialize ClientTimeout whenever an EAP
peer method is initialized to avoid this. This addresses problems
where WPS (EAP-WSC) reduces the timeout and consecutive EAP runs
may fail due to too small timeout.
If the peer you want to connect to is no longer available (does not
acknowledge frames) when wpa_supplicant sends GO Negotition Request
frames, retransmission of this frame is done until the associated
p2p_device structure is removed on timeout. In that case, no signal
is emitted to inform the GO Negotiation has failed.
When sending an Invitation Request frame, the same retransmission
mechanism is in place but limit the transmission to 100 and hitting
the limit generates an event.
This patch adds the same mechanism as the one in place for Invitation
Request, but with limit of 120 to match the existing wait_count for
for GO Negotiation.
If a station received unprotected Deauthentication or Disassociation
frame with reason code 6 or 7 from the current AP, there may be a
mismatch in association state between the AP and STA. Verify whether
this is the case by using SA Query procedure. If not response is
received from the AP, deauthenticate.
This implementation is only for user space SME with
driver_nl80211.c.
Some new code will require access to P2P group members, so add API to
retrieve the number of members and iterate the members themselves.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If there is a pending GO Negotiation when p2p_cancel is used,
unauthorize the peer to avoid immediate reconnection from being
accepted without a new p2p_connect command.
This can be used by external programs (e.g., wlantest_cli) to inject
raw frames (hex dump of the frame header and body). The data can be
requested to be sent as-is or protected with the current key.
