If a link is unreachable, the specification mandates we should send a
teardown packet via the AP with a specific teardown reason. Force this
by first disabling the link and only then sending the teardown packet
for the LOW_ACK event.
Rename the TDLS LOW_ACK event handler to better reflect its purpose.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
The following kde.rsn_ie_len != peer->rsnie_i_len was already taking
care of enforcing the length to be within the target buffer length.
Anyway, this explicit check makes this clearer and matches the design in
TPK M1 processing.
Signed-off-by: Jouni Malinen <j@w1.fi>
Disabling the link only clears the local state. The remote peer will
still think we are connected and disallow the setup.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
When de-authenticating from the AP, disable each TDLS link after
sending the teardown packet. Postpone the reset of the peer state
data until after the link disable request.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Commit 96ecea5eb1 did not consider
to pass the VHT/HT/WMM capabilities of the peer for BSS with
open mode.
Address this issue by passing the capabilities irrespective of
the security mode.
Signed-off-by: Pradeep Reddy POTTETI <c_ppotte@qti.qualcomm.com>
"SET tdls_testing 0x800" can be used to enable a special test mode that
forces the FTIE MIC in TDLS setup messages to be incorrect.
Signed-off-by: Jouni Malinen <j@w1.fi>
While framing the TDLS Setup Confirmation frame, the driver needs to
know if the TDLS peer is VHT/HT/WMM capable and thus shall construct the
VHT/HT operation / WMM parameter elements accordingly. Supplicant
determines if the TDLS peer is VHT/HT/WMM capable based on the presence
of the respective IEs in the received TDLS Setup Response frame.
The host driver should not need to parse the received TDLS Response
frame and thus, should be able to rely on the supplicant to indicate
the capability of the peer through additional flags while transmitting
the TDLS Setup Confirmation frame through tdls_mgmt operations.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
TDLS Setup Request/Response frames from the peers include the WMM IE,
hence parse the same and consider the QoS Info from the WMM IE. The
qos_info obtained in the WMM IE overwrites the one obtained through
WLAN_EID_QOS attribute.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The information of the peer's supported channel and operating class
is required for the driver to do TDLS off channel operations with a
compatible peer. Pass this information to the driver when the peer
station is getting added.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
A reenable of the TDLS link while the host driver is already processing
the same (due to the retransmitted M2/M3 frames) might result in a
failed TDLS setup handshake due to some host driver's implementation.
Thus, issue enable link only when the peer's TDLS status signifies no
prior link (tpk_success=0).
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Add DBus methods for TDLS operations similar to those available
for the control interface. This includes Discover, Setup, and
Teardown commands. While here, add a method to query the TDLS
link status and add a DBus method for it.
Tested with CONFIG_TDLS enabled, on a TDLS-enabled host and
peer capable of TDLS:
dbus-send --system --dest=fi.w1.wpa_supplicant1 --print-reply \
/fi/w1/wpa_supplicant1/Interfaces/0 \
fi.w1.wpa_supplicant1.Interface.TDLSStatus string:<peer-mac-address>
yields: string "peer does not exist"
dbus-send --system --dest=fi.w1.wpa_supplicant1 --print-reply \
/fi/w1/wpa_supplicant1/Interfaces/0 \
fi.w1.wpa_supplicant1.Interface.TDLSDiscover string:<peer-mac-address>
yields no error
dbus-send --system --dest=fi.w1.wpa_supplicant1 --print-reply \
/fi/w1/wpa_supplicant1/Interfaces/0 \
fi.w1.wpa_supplicant1.Interface.TDLSSetup string:<peer-mac-address>
yields no error
dbus-send --system --dest=fi.w1.wpa_supplicant1 --print-reply \
/fi/w1/wpa_supplicant1/Interfaces/0 \
fi.w1.wpa_supplicant1.Interface.TDLSStatus string:<peer-mac-address>
yields: string "connected" after TDLS completes
dbus-send --system --dest=fi.w1.wpa_supplicant1 --print-reply \
/fi/w1/wpa_supplicant1/Interfaces/0 \
fi.w1.wpa_supplicant1.Interface.TDLSTeardown string:<peer-mac-address>
yields no error
dbus-send --system --dest=fi.w1.wpa_supplicant1 --print-reply \
/fi/w1/wpa_supplicant1/Interfaces/0 \
fi.w1.wpa_supplicant1.Interface.TDLSStatus string:<peer-mac-address>
yields: string "peer not connected"
Signed-hostap: Paul Stewart <pstew@chromium.org>
A new TDLS request shall transmit TPK M1 frame with a unique INonce.
Thus a new explicit request would fail an ongoing TDLS negotiation with
the error "TDLS: FTIE SNonce in TPK M3 does not match with FTIE SNonce
used in TPK M1" if the peer happens to receive two M1 frames before an
M3 frame. Check for the ongoing negotiation with the peer and do not
start a new one if we are already in a setup negotiation with the peer.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
There is no need to go through the peer list when we already have a
pointer to the specific peer entry.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This is called from number of locations and it is more efficient to use
a new helper function instead of wpa_tdls_disable_link() that would do
peer address search from the list of peers.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Making this function be used only for external setup case simplifies the
implementation and makes core wpa_supplicant calls in ctrl_iface.c and
events.c consistent.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
There is no point in updating the RNonce for every obtained TPK M1 frame
(e.g., retransmission due to timeout) with the same INonce (SNonce in
FTIE). Update RNonce only if a TPK M1 is received with a different
INonce (new TDLS session) to avoid issues with two setup exchanges
getting mixed and exchange failing due to mismatching nonces ("TDLS:
FTIE ANonce in TPK M3 does not match with FTIE ANonce used in TPK M2").
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Clear the peer information and disable the created link on a
failed TDLS setup negotiation. This is needed to avoid leaving
TDLS setup pending and to return to the AP path in case anything
goes wrong during the setup attempt.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
A transmission failure of the TDLS Setup Request frame (TPK Handshake
M1) results in no further retries and the peer entry being left in state
where all TDLS Setup Request frames from the peer with higher address
would be rejected, thus always resulting in a failure to establish a
TDLS link. Handle the failures in transmission by disabling the link
immediately to ensure the traffic to the peer goes through the AP. This
commit also handles similar transmision failures for TPK Handshake M2
and M3 frames (TDLS Setup Response and Confirm).
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The ext_supp_rates passed to merge_byte_arrays would be invalid if not
advertized by the TDLS peer. Thus, validate the argument to avoid
crashes in such cases.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
TDLS responder STA used to retransmit the TDLS Setup Response after 5
seconds if the TDLS Setup Confirm is not received. The initiator would
have enabled the TDLS link and started transmitting the data to the peer
on the TDLS link after transmitting the TDLS Setup Confirm frame. If the
TDLS Setup Confirm frame is not received by the receiver, the
transmissions from the initiator on the direct link would get failed for
the TDLS link not getting enabled on the receiver. This commit reduces
the data delivery failure duration by shortening the retry time of the
TDLS Setup Response frames. The retry limit of the TDLS Response frame
also is increased to ensure that the peer does not miss the frames in
the reduced time period.
Signed-hostap: Sunil Dutt <duttus@codeaurora.org>
The reason code for the teardown request is overwritten for open
mode. This commit removes the code that does so by reverting parts
of commit 0cb12963b6.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The information of the peer's AID is required for the driver to
construct partial AID in VHT PPDU's. Pass this information to the driver
during add/set station operations (well, as soon as the information is
available, i.e., with set station operation currently).
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
A kernel commit ("mac80211: fix FT roaming") started validating that the
STA entry is marked associated when adding a key. While this is needed
to fix some FT use cases with hardware crypto, it has a side effect of
breaking TDLS key configuration. Work around this by trying to
re-configure the key for the direct link after the STA entry has been
set with all information. In addition, try to tear down the link if
anything goes wrong in key configuration (if both attempts fail) or
enabling the link in the driver.
Signed-hostap: Jouni Malinen <j@w1.fi>
Enhance TDLS Setup Request processing to support both external and
internal TDLS setup for the case where concurrent TDLS initialization
results in the TDLS Setup Request from the peer getting accepted.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
wpa_tdls_peer_free() ended up getting called after some of the
parameters from the TDLS Setup Request frame were copied into the struct
wpa_tdls_peer information. This could result in continuing with cleared
information in case the new exchange was the one that is used in
concurrent initialization case or if this is to re-negotiated an
existing TDLS link. The driver would not be provided with all the peer
capabilities correctly in such case.
Fix this by moving the existing_peer check to happen before the
information from the TDLS Setup Request frame is copied.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
If we accept the peer TPK M1 after having sent our TPK M1, we need to
reject TPK M2 from the peer to avoid going through two TDLS setup
exchanges.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
If the previously started setup is terminated in case both peers
initiate TDLS link at more or less the same time, disable the old link
to allow the dummy station entry to be deleted from cfg80211 so that a
new entry can be added for the setup direction that will be allowed to
proceed.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The information of the peer's VHT capability is required for the
driver to establish a TDLS link in VHT mode with a compatible peer.
Pass this information to the driver when the peer station is
getting added.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The contents of the peer's capability and extended capability
information is required for the driver to perform TDLS P-UAPSD and Off
Channel operations. Pass this information to the driver when the peer
station is getting added.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The information of the peer's HT capability and the QOS information is
required for the driver to perform TDLS operations. Pass this
information to the driver when the peer station is getting added.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
A TDLS Teardown frame with Reason Code 3 (Deauthenticated because
sending STA is leaving (or has left) IBSS or ESS) shall be transmitted
to all TDLS peer STAs (via the AP or via the direct path) prior to
transmitting a Disassociation frame or a Deauthentication frame to the
AP.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The reason code used for calculating the MIC should correspond to the
reason code with which the teardown frame is sent, as the receiver shall
use the one obtained in the frame for validating the MIC.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
If an implicit TDLS set up request is obtained on an existing link or an
to be established link, the previous link was not removed. This commit
disables the existing link on a new set up request. Also,
wpa_tdls_reneg() function was invoking wpa_tdls_start() on an already
existing peer for the case of internal setup, which is incorrect. Thus
the invocation of wpa_tdls_start() is removed in wpa_tdls_reneg() and
also this function is renamed to wps_tdls_remove() as it does not
renegotiation rather shall remove the link (if any) for the case of
external setup.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
There is no need to have this check copied to each caller since this
needs to be done for every case when a new peer is being added.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Peer entries were getting added on every discover request from the peer,
thus resulting in multiple entries with the same MAC address. Ensures
that a check is done for the presence of the peer entry and reuse the
existing entry instead of adding a new one.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Remove the GPL notification text from files that were initially
contributed by Atheros Communications or Qualcomm Atheros.
Signed-hostap: Jouni Malinen <j@w1.fi>
TPK will be needed to be able to generate FTIE MIC for the
teardown message, so maintain peer data for a bit longer in
case the teardown FTIE request comes back from the driver.
Use the wpa_tdls_add_peer function to allocate TDLS peer structures.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Cc: Kalyan C Gaddam <chakkal@iit.edu>
Use capability information to decide whether to perform a given TDLS
operation internally or through mgmt-frame Tx.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Cc: Kalyan C Gaddam <chakkal@iit.edu>
Before commencing setup, add a new STA entry to the driver representing
the peer. Later during setup, update the STA entry using information
received from the peer.
Extend sta_add() callback for adding/modifying a TDLS peer entry and
connect it to the TDLS state machine. Implement this callback for the
nl80211 driver and send peer information to kernel.
Mark TDLS peer entries with a new flag and translate it to a
corresponding nl80211 flag in the nl80211 driver.
In addition, correct TDLS related documentation in the wpa_driver_ops
structure.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Cc: Kalyan C Gaddam <chakkal@iit.edu>
Record the capabilities and supported rates of the TDLS peer during
link setup. These are given in the IEs passed in Setup Request and
Setup Response frames.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Cc: Kalyan C Gaddam <chakkal@iit.edu>
