Explicitly check for iface->current_mode before dereferencing it. While
this case may not happen in practice, it is better for the setup
functions to be more careful when doing the initial band selection.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Allow the Manufacturer information for a found P2P peer device to be
fetched through the D-Bus interface similarly to p2p_peer <mac address>
on ctrl interface.
Signed-off-by: Amit Khatri <amit.khatri@samsung.com>
Signed-off-by: Rahul Jain <rahul.jain@samsung.com>
Signed-off-by: Ashutosh Kaushik <k.ashutosh@samsung.com>
Avoid memory leak due to previous allocation for ssid->ssid. It does not
look like this is hit in normal cases, but at might be possible for the
SSID to get set if the peer is present in previous scan results and WPS
code ends up copying the SSID from there.
Signed-off-by: Purushottam Kushwaha <p.kushwaha@samsung.com>
Add support to compile libwpa_client.so. This can be used by external
programs to interact with the wpa_supplicant control interface. Also
rename the static version of this library to libwpa_client.a to be
consistent with the name used previous in Android builds.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
A new Invitation Request might be received on a just started persistent
group if the previous Invitation Response sent isn't received at the
peer (GO of the persistent group). When the peer sends an Invitation
Request again, treat it as start of group formation and restart the
group formation timer at this point of time.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
In the case of driver-based BSS selection, a bssid_hint in the connect
request might not result in to the selection of the same BSS. Thus,
postpone the updation of the wpa_s->current_bss till the association
event is received unless the BSSID is forced. This fixes issues where
wpa_s->current_bss may end up being updated to point to the BSS that
wpa_supplicant provided as a hint for a roaming case, but then not
restored if the driver decides to "return" to the current BSS instead.
This could result in some operations (e.g., WNM BSS TM response) not
working properly due to incorrect BSS being identified in
wpa_s->current_bss.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
When device supports dual band operations with offloaded ACS, hw_mode
can now be set to any band (hw_mode=any) in order to allow ACS to select
the best channel from any band. After a channel is selected, the hw_mode
is updated for hostapd.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
D-Bus used the p2p_dev member in struct wpa_supplicant to track the
interface used for P2P Device operations. However, this is not needed as
the interface used for P2P Device operations is stored in struct
wpa_global->p2p_init_wpa_s.
Replace all the redirections to wpa_s->p2p_dev with redirections to
wpa_s->global->p2p_init_wpa_s and removed this member as it is no
longer needed.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
This command is for a specific P2P group, not for the P2P Device
instance and as such, wpa_s pointer must not be replaced with the
interface that is used for P2P Device management.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The function used wpa_s->parent->conf to iterate the P2P networks and
update the configuration file. However, wpa_s->parent is not
necessarily the interface used to manage the P2P Device operations.
Fix this by accessing the configuration file of the interface
initialized to manage the P2P Device operations.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
The function used wpa_s->parent->conf to iterate the P2P networks and
update the configuration file. However, wpa_s->parent is not
necessarily the interface used to manage the P2P Device operations.
Fix this by accessing the configuration file of the interface initialized
to managed the P2P Device operations.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
wpas_p2p_set_own_freq_preference() accessed wpa_s->parent->conf to test
if p2p_ignore_shared_freq is set, but wpa_s->parent is not necessarily
the interface used to manage the P2P Device operations.
Fix this by accessing the configuration file of the interface
initialized to manage the P2P Device operations.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
As wpas_p2p_remove_client() is not necessarily called from the interface
used to manage the P2P Device operations, when removing a client, use
the P2P management interface to iterate over the saved networks and
remove the relevant entries form the P2P GO network blocks.
Signed-off-by: Ben Rosenfeld <ben.rosenfeld@intel.com>
Commit 1c2aa04c96 ('P2P: Do not add P2P
IEs on P2P disabled interface') removed the P2P IEs from association on
non-P2P interface. However, an AP functioning as a P2P manager needs the
cross connection capability of the station (P2P Device). This needs to
be done to meet the P2P specification requirements even if the station
interface has p2p_disabled=1 in case P2P in general is enabled.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
While RFC 6124 does not define how Session-Id is constructed for
EAP-EKE, there seems to be consensus among the authors on the
construction. Use this Type | Nonce_P | Nonce_S construction based on
the following email:
From: Yaron Sheffer <yaronf.ietf at gmail.com>
To: ietf at ietf.org
Date: Wed, 17 Nov 2010 13:13:42 +0200
Expanding on my previous response, I suggest to resolve Bernard's
concern by adding the following text:
5.6 EAP Key Generation
EAP-EKE can be used for EAP key generation, as defined by [RFC 5247].
When used in this manner, the values required to establish the key
hierarchy are defined as follows:
- Peer-Id is the EAP-EKE ID_P value.
- Server-Id is the EAP-EKE ID_S value.
- Session-Id is the concatenated Type | Nonce_P | Nonce_S, where Type is
the method type defined for EAP-EKE in [Sec. 4.1], a single octet.
Thanks,
Yaron
Signed-off-by: Jouni Malinen <j@w1.fi>
OpenSSL is moving to use 2048-bit DH key size as the default with
dhparam. Increase the value in the hostapd.conf to match that to reduce
likelihood of ending up using a shorter key.
Signed-off-by: Jouni Malinen <j@w1.fi>
The ACS code part of hostapd scans all the channels even if the channel
list is specified in the hostapd.conf. Limit the ACS scan channels to
the list specified in the config file.
Signed-off-by: Srinivasa Duvvuri<sduvvuri@chromium.org>
Commit 5add410162 ('WPS: Use shorter
authentication timeout during no-SelReg iteration') broke the build with
WPS disabled.
Signed-off-by: Jouni Malinen <j@w1.fi>
The dev[1] <--> dev[2] data connectivity test was using incorrect
function. dev[2] is also using a P2P group and as such, can have a
different group interface.
Signed-off-by: Jouni Malinen <j@w1.fi>
Group interface name was fetched from the results of an incorrect group
formation and because of this, group removal failed in case P2P Device
is used and dev[1] ends up getting different group ifname for the
groups.
Signed-off-by: Jouni Malinen <j@w1.fi>
The network operations need to use the global control interface to be
performed on the interface that stores the network profiles for
persistent groups.
Signed-off-by: Jouni Malinen <j@w1.fi>
After P2P-GROUP-STARTED event, use group_form_result in order to update
the group_ifname for the device. This is needed when using P2P Device
for managing P2P operations which results in a separate group interface
being used.
Signed-off-by: Ben Rosenfeld <ben.rosenfeld@intel.com>
In case that there is a need to list the persistent P2P networks,
the global control interface needs to be used.
Signed-off-by: Ben Rosenfeld <ben.rosenfeld@intel.com>
list_networks() always used the wlanX control interface to query for the
current list of networks. However, when a dedicated P2P Device is used,
the global control interface should be used when checking persistent
group network profiles.
Fix this by adding an optional parameter indicating that the P2P
networks are requested, and in such a case use the global control
interface.
In addition update test_p2p_persistent to use the argument when needed.
Signed-off-by: Ben Rosenfeld <ben.rosenfeld@intel.com>
This is required for cases that a dedicated P2P Device interface
is used and then the event will happen on the global interface.
Signed-off-by: Ben Rosenfeld <ben.rosenfeld@intel.com>
Send request to set persistent_reconnect on the global control
interface so it would also work when using a dedicated P2P Device
interface.
Signed-off-by: Ben Rosenfeld <ben.rosenfeld@intel.com>
When testing P2P invitation flow, setting the NFC selector
should be done using the global control interface.
Signed-off-by: Ben Rosenfeld <ben.rosenfeld@intel.com>
Some tests in test_p2ps.py test a scenario where a separate P2P
group interface is not used. However, this is not a valid case
when a dedicated P2P Device interface is used, as in such a case
a separate group interface must be used.
Handle this by skipping such tests in case a dedicated P2P Device is
used.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Call group_form_result() whenever a new group is started, so that
group_ifname gets updated and later, the group can be removed when
needed.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>