Change send_mlme() API to allow sending management frames on a specific
channel, overriding the internal driver decision.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
This modifies struct wpa_ptk to allow the length of KCK and KEK to be
stored. This is needed to allow longer keys to be used, e.g., with
Suite B 192-bit level.
Signed-off-by: Jouni Malinen <j@w1.fi>
For CONFIG_TESTING_OPTIONS=y builds, add a new test parameter than can
be used to trigger various error cases within wpa_supplicant operations
to make it easier to test error path processing. "SET test_failure
<val>" is used to set which operation fails. For now, 0 = no failures
and 1 = scan trigger fails with EBUSY. More operations can be added in
the future to extend coverage.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The supplicant code does not try to control the actual channel of the
radio at any point. It simply passes the target peer and channel
parameters to the driver. It's the driver's responsibility to
periodically initiate TDLS channel-switch operations when TDLS
channel-switching is enabled.
Allow enable/disable operations to be invoked via the control interface.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
The send_eapol() callback was used by driver_test.c, but with that
removed, there is no remaining users of the alternative EAPOL frame
transmitting mechanism in wpa_supplicant, i.e., all remaining driver
interfaces use l2_packet instead. Remove the send_eapol() to get rid of
unused code.
Signed-off-by: Jouni Malinen <j@w1.fi>
This reduced number of unnecessarily duplicated driver interface
callback functions for sending Action frames by using the more generic
send_action() instead of FT specific send_ft_action().
Signed-off-by: Jouni Malinen <j@w1.fi>
Add add_tx_ts() and del_tx_ts() ops to notify the driver about
TSPEC add / delete.
Additionally, add wmm_ac_supported flag to indicate
whether the driver supports WMM AC.
Signed-off-by: Moshe Benji <moshe.benji@intel.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Create init_mesh, mesh_join, and mesh_leave actions to kernel.
Signed-off-by: Javier Lopez <jlopex@gmail.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: Jason Mobarak <x@jason.mobarak.name>
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Some drivers need to know the initiator of a TDLS connection in order
to generate a correct TDLS mgmt packet. It is used to determine
the link identifier IE. Pass this information to the driver.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
The network block bssid parameter can be used to force a specific BSS to
be used for a connection. It is also possible to modify this parameter
during an association. Previously, that did not result in any
notification to the driver which was somewhat problematic with drivers
that take care of BSS selection. Add a new mechanism to allow
wpa_supplicant to provide a driver update if the bssid parameter change
for the current connection modifies roaming policy (roaming
allowed/disallowed within ESS).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add a new wowlan_triggers option to wpa_supplicant.conf. The triggers in
this key will be used to configure the kernel wowlan configuration.
For now, support only simple flags. More complex triggers can be added
later on.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
While framing the TDLS Setup Confirmation frame, the driver needs to
know if the TDLS peer is VHT/HT/WMM capable and thus shall construct the
VHT/HT operation / WMM parameter elements accordingly. Supplicant
determines if the TDLS peer is VHT/HT/WMM capable based on the presence
of the respective IEs in the received TDLS Setup Response frame.
The host driver should not need to parse the received TDLS Response
frame and thus, should be able to rely on the supplicant to indicate
the capability of the peer through additional flags while transmitting
the TDLS Setup Confirmation frame through tdls_mgmt operations.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add a callback to the driver interface that allows vendor specific
commands to be sent. In addition, a control interface command is added
to expose this new interface outside wpa_supplicant:
Vendor command's format:
VENDOR <vendor id> <sub command id> [<hex formatted data>]
The 3rd argument will be converted to binary data and then passed as
argument to the sub command.
This interface is driver independent, but for now, this is only
implemented for the nl80211 driver interface using the cfg80211 vendor
commands.
Signed-off-by: Beni Lev <beni.lev@intel.com>
Track set_key operations per-key index and clear keys on disconnection
only if the key was set (or may have been set which is the case for the
first operation after wpa_supplicant start).
Signed-hostap: Jouni Malinen <j@w1.fi>
The option of handling upper layer P2P management operations within the
driver/firmware was originally planned to be used with wpa_supplicant,
but this has not really happened and there is no clear sign of this
being needed in the near term either. This functionality has not been
completed and it is certainly not being kept up-to-date or tested. As
such, it is best to remove it for now and if this or something similar
is needed in the future, it can be brought back once a clear need for it
has been demonstrated first.
Signed-hostap: Jouni Malinen <j@w1.fi>
This is a mechanism used in Android to extend driver interface in vendor
specific ways. This is included only for the purpose of Android
compatibility. Proper interface commands should be used for any new
functionality.
Signed-hostap: Jouni Malinen <j@w1.fi>
Add csa_settings struct which holds parameters for CSA. Change driver
interface for switch_channel(), so that it will receive this struct and
not only the new frequency as it was before. This allows wpa_supplicant
to provide all the required parameters (beacons, proberesp, assocresp,
CSA IE) which are required by cfg80211 implementation.
Signed-hostap: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
When removing and re-adding the first wlan# netdev to hostapd
dynamically, the netdev is already present and should not be removed and
re-added to maintain its state as not-added-by-hostapd so that it does
not get removed automatically.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Indicate support for QoS Mapping and configure driver to update the QoS
Map if QoS Map Set elements is received from the AP either in
(Re)Association Response or QoS Map Configure frame.
This commit adds support for receiving the frames with nl80211 drivers,
but the actual QoS Map configuration command is still missing.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
STATUS-DRIVER command can now be used to fetch driver interface status
information. This is mainly for exporting low-level driver interface
information for debug purposes.
Signed-hostap: Jouni Malinen <j@w1.fi>
Commit 1aef400bf0 implemented IBSS RSN
disconnect() call using sta_deauth() in a way that resulted in NULL
pointer dereference in driver_nl80211.c if SME was in user space. Fix
this by passing the own MAC address in the sta_deauth call.
Signed-hostap: Jouni Malinen <j@w1.fi>
Commits 07783eaaa0 and
3da372fae8 removed the only users of the
disassociate() driver operation, so these driver wrapper functions can
also be removed now.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
On P2P group removal, the GO is deinitialized correctly (and the vif
mode is set back to sta in case of nl80211), but the P2P client mode
wasn't deinitialized, and the nl80211 vif stays in P2P client mode.
Add a new deinit_p2p_cli op (similar to deinit_ap), which currently only
sets the interface back to station mode.
Signed-hostap: Eliad Peller <eliad@wizery.com>
intended-for: hostap-1
"wpa_cli set radio_disabled 1/0" can be used to disable/enable
radio to simulate out-of-radio-range condition in a testbed
device.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This can be used to request Provision Discovery Request to be sent
for the purpose of joining a running group, e.g., to request the GO
to display a PIN that we can then use with p2p_connect join command.
Signed-hostap: Jithu Jance <jithu@broadcom.com>
Use the no-ACK send_mlme request to transmit Probe Response frames
in P2P Listen state. This reduces number of unnecessary transmissions
if the peer device has already moved away from the channel. It will most
likely go through Search state multiple times anyway, so even if the
response were to be lost, a new retry will happen at higher layer.
Signed-hostap: Jouni Malinen <j@w1.fi>
In some situations it might be benefical to send a unicast frame without
the need for getting it ACKed (probe responses for example). In order to
achieve this add a new noack parameter to the drivers send_mlme callback
that can be used to advise the driver to not wait for an ACK for this
frame.
Signed-hostap: Helmut Schaa <helmut.schaa@googlemail.com>
This function was used unconditionally if wpa_supplicant build
includes CONFIG_P2P=y. Adding a separate driver_ops for such use
is not really useful since the driver wrappers can do the same
internally. Remove this driver_ops and move matching functionality
into driver_nl80211.c which was the only driver wrapper using
this driver_ops callback.
Signed-hostap: Jouni Malinen <j@w1.fi>
This can be used to apply the no-CCK rule conditionally depending on
which frame is being sent. The no-CCK rule applies only for P2P
management frames while SA Query and FT use cases do not have similar
restrictions.
Signed-hostap: Jouni Malinen <j@w1.fi>
These driver_ops functions set_channel, set_ssid, set_bssid,
mlme_add_sta, and mlme_remove_sta were used with the user space
MLME implementation in wpa_supplicant. That was only for testing
purposes and was removed, but these driver_ops were forgotten.
Remove them now to remove confusing driver_ops definitions.
In new Linux kernel versions (>=3.0), nl80211 adds scheduled scan
capability. In order to use this feature to its full extent, we need
to support it in the wpa_supplicant core, so that it can also be used
by other drivers.
This commit adds initial scheduled scan support operations and events.
Signed-off-by: Luciano Coelho <coelho@ti.com>
This change is a first step in better supporting different driver
architectures for AP mode operations with nl80211. This commit in
itself does not add new functionality, but it makes it easier to add
new AP mode parameters to address needs of drivers that have more of
the MLME/SME in firmware or kernel.
Add support to wpa_supplicant for device-based GTK rekeying. In order to
support that, pass the KEK, KCK, and replay counter to the driver, and
handle rekey events that update the latter.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This should fix EAPOL reauthentication and rekeying timeout issues
with Intel clients when using WMM (e.g., with IEEE 802.11n). These
stations do not seem to be able to handle EAPOL data frames as
non-QoS Data frames after the initial setup.
This adds STA flags to hapd_send_eapol() driver op to allow
driver_nl80211.c to mark the EAPOL frames as QoS Data frame
when injecting it through the monitor interface.
This provides a means for the supplicant to directly request signal
quality metrics from the driver. This is useful, for example for
background scan algorithms that might ask desire this information
out-of-band with CQM events.
Signed-off-by: Paul Stewart <pstew@google.com>
This adds partial callbacks and events to allow P2P management to be
implemented in a driver/firmware. This is not yet complete and is
very much subject to change in the future.
With the new kernel functionality coming to Linux to allow off-channel
TX, we can take advantage of that in the P2P code that currently uses
remain-on-channel. If a driver advertises support for it, it will be
asked to handle off-channel TX by itself.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
WPS 2.0 mandates the AP to include WPS IE in (Re)Association Response
if the matching (Re)Association Request included WPS IE. Provide the
needed WPS IE information to the driver_ops API for drivers that
process association frames internally.
Note: This modifies the driver_ops API by adding a new argument to
set_ap_wps_ie().
For now, this applies to the test command that can be used to set
periodic NoA (p2p_set noa). The value are stored and periodic NoA
is enabled whenever there are no non-P2P STAs connected to the GO.
There is no absolute requirement for separating address allocation
into separate functions, so simplify the driver wrapper interface
to use just if_add and if_remove instead of adding the new
alloc_interface_addr() and release_interface_addr() functions.
if_add() can now indicate if the driver forced a different interface
name or address on the virtual interface.
wpa_supplicant can now be notified of suspend/resume events, e.g.,
from pm-action scripts. This allows wpa_supplicant to clear information
that may become invalid during a suspend operation.
Some drivers may need to use a specific ifname for the virtual
interface, so allow them to do this with a new parameter passed
to the alloc_interface_addr() handler.
This adds new commands and events for allowing off-channel Action
frame exchanges to be requested. This functionality is not yet used
and is only fully supported by driver_test.c at this point.
driver_nl80211.c has support for the remain-on-channel commands, but
the Action frame TX/RX part is still pending review for the kernel
code and as such, is not yet included here.
This adds placeholder code for allowing the virtual interfaces to be
pre-allocated a MAC address before the interface type is known with
drivers that do not handle interface type changes.
This gets rid of previously deprecated driver_ops handlers set_wpa,
set_drop_unencrypted, set_auth_alg, set_mode. The same functionality
can be achieved by using the init/deinit/associate handlers.
Clean up driver interface by merging hostapd and wpa_supplicant
specific set_beacon driver_ops into a single one. In addition,
merge set_beacon_int into to the same operation.
wpa_supplicant can now initialize hostapd data structures when mode=2 is
used to set up an AP. The hostapd configuration is not yet set based on
wpa_supplicant network configuration block. In addition, the glue code
for hostapd driver_ops needs number of functions that will be needed for
AP functionality.
