1. Add parameters to the scan command to allow MAC address
randomization during scan and scheduled scan.
2. Add capability bits to publish MAC address randomization support
in scan and scheduled scan.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
The kernel-driver/firmware are responsible for performing periodic
switches to the target channel with the given peer. Propagate all TDLS
channel switching related information to kernel.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
The supplicant code does not try to control the actual channel of the
radio at any point. It simply passes the target peer and channel
parameters to the driver. It's the driver's responsibility to
periodically initiate TDLS channel-switch operations when TDLS
channel-switching is enabled.
Allow enable/disable operations to be invoked via the control interface.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
If registering WMM-AC ADDTS response action frame or WMM-AC DELTS
action frame fails, the management frame handler is not being
registered. This results with a segmentation fault when trying to
unsubscribe the handler when the interface is removed.
Fix it by always registering the handler and just returning a negative
value to note that the action frame could not be registered.
This fixes an issue introduced in the commit
dfa8787833 ('nl80211: Implement
add_ts/del_ts ops').
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
This reduces the time possible keys could remain in heap memory. Couple
of the nl80211 messages include keys (TK for normal ciphers and
KCK/KEK/PMK for various offloading cases).
Signed-off-by: Jouni Malinen <j@w1.fi>
There was one final remaining linux_set_iface_flags() call that did not
check the result. This specific one does not really matter much, but
anyway, be more consistent by checking the result and log any error in
debug log. (CID 74146)
Signed-off-by: Jouni Malinen <j@w1.fi>
This converts most of the remaining perror() and printf() calls from
hostapd and wpa_supplicant to use wpa_printf().
Signed-off-by: Jouni Malinen <j@w1.fi>
struct wpa_driver_associate_params moved to using struct
hostapd_freq_params instead of just frequency. Need to update wpa_priv
to do same.
Signed-off-by: Jouni Malinen <j@w1.fi>
It would be at least theoretically possible for the bridge netdev to
have disappeared at the time hostapd processes the RTM newlink/dellink
message. As such, it is better to verify that if_indextoname() actually
returned success before printing the bridge ifname in debug. In
addition, there is not much point trying to add the bridge ifindex into
the list of own ifindexes in case the interface has already been
removed, so skip that part as well.
Signed-off-by: Jouni Malinen <j@w1.fi>
This was used in the past, but all the event processing is now either
through process_global_event() or process_bss_event().
Signed-off-by: Jouni Malinen <j@w1.fi>
Maximum number of peer links is maximum number of connecting mesh peers
at the same time. This value is 0..255 based on the
dot11MeshNumberOfPeerings range.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
The local ifindex list needs to be updated only if the current bridge
interface is the correct one. If hostapd is going to move the interface
to another bridge, the old bridge ifindex must not be added. In
addition, when removing the bridge interface on deinit, it may need to
be set down to allow bridge removal.
Signed-off-by: Jouni Malinen <j@w1.fi>
The interface was incorrectly changed to station mode between the two
IBSS join requests and that made the second attempt fail. Remove that
undesired mode clearing from this special case of IBSS leave sequence.
Signed-off-by: Jouni Malinen <j@w1.fi>
Commit 9f12614b8c ('nl80211: Do not
encrypt IEEE 802.1X WEP EAPOL') tried to use
NL80211_ATTR_CONTROL_PORT_NO_ENCRYPT to disable encryption of EAPOL
frames for WEP IEEE 802.1X. However, it used incorrect key management
suite (IEEE 802.1X with WPA/WPA2 while the non-WPA version is needed
here). Consequently, the no-encrypt flag was never set to the driver
(WPA/WPA2 cases do not meet the WEP as pairwise criteria).
Signed-off-by: Jouni Malinen <j@w1.fi>
The mesh gate is used to bridge (or route) between mesh network and
another network. For example, mesh gate acts as router between mesh
network and IEEE 802.11 BSS network.
This command makes a virtual mesh interface to be used for mesh gate.
This command expects to be used like this.
wpa_cli -i wlan0 MESH_INTERFACE_ADD ifname=mesh0
wpa_cli -i mesh0 add_network
wpa_cli -i mesh0 set_network 0 ssid '"commell_2X_mmm"'
wpa_cli -i mesh0 set_network 0 mode 5
wpa_cli -i mesh0 set_network 0 frequency 2412
wpa_cli -i mesh0 set_network 0 key_mgmt SAE
wpa_cli -i mesh0 set_network 0 psk '"01234567"'
wpa_cli -i mesh0 mesh_group_add 0
wpa_cli -i wlan0 mesh_group_remove mesh0
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
Building wpa_supplicant with the musl C library fails since musl does
not define type names such as '__uint32_t'. To support building
wpa_supplicant with the musl C library use the integer types declared in
the ISO C standard header file <stdint.h>.
Signed-off-by: Jörg Krause <jkrause@posteo.de>
drv->ctx always points to the first BSS and we should report event using
BSS related to the interface we got NL80211_CMD_NEW_STATION from.
This fixes STA association for drivers using NL80211_CMD_NEW_STATION and
multiple virtual interfaces.
Before:
nl80211: Drv Event 19 (NL80211_CMD_NEW_STATION) received for wlan0-1 (ifindex:7)
nl80211: New station 02:00:00:00:01:00
wlan0: STA 02:00:00:00:01:00 IEEE 802.11: associated
After:
nl80211: Drv Event 19 (NL80211_CMD_NEW_STATION) received for wlan0-1 (ifindex:7)
nl80211: New station 02:00:00:00:01:00
wlan0-1: STA 02:00:00:00:01:00 IEEE 802.11: associated
This is not applicable to the cases where authentication (AP SME & MLME)
is in hostapd and hostapd_assoc_cb() instead of hostapd_notif_assoc()
handles BSS selection.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
The send_eapol() callback was used by driver_test.c, but with that
removed, there is no remaining users of the alternative EAPOL frame
transmitting mechanism in wpa_supplicant, i.e., all remaining driver
interfaces use l2_packet instead. Remove the send_eapol() to get rid of
unused code.
Signed-off-by: Jouni Malinen <j@w1.fi>
This commit introduces a QCA vendor command that allows interrogation of
the vendor-specific features supported by the device/driver. Currently
the only defined feature is the ability to offload key management.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
It is possible for unmasking of 11b rates to fail if a P2P group is
terminated while the netdev is down (e.g., due to rfkill block). This
could result in the 11b TX rates being left masked for non-P2P
operations. This would be particularly unfortunate for channel 14 use
since OFDM rates are not allowed on channel 14 and only OFDM rates were
configured P2P. This issue showed up, e.g., when running hwsim test case
rfkill_autogo followed by ap_wps_conf_chan14.
It may be possible to allow the failed operation in cfg80211/mac80211,
but it looks better to work around this on wpa_supplicant side as well.
Try to unmask the 11b rates again on the next connection request if the
rate unmasking operation had failed.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This makes it easier to debug issues related to TX rate masking for P2P
use cases (and unmasking for non-P2P).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This converts os_snprintf() result validation cases to use
os_snprintf_error() in cases where success condition was used to execute
a step. These changes were done automatically with spatch using the
following semantic patch:
@@
expression E1,E2,E3;
statement S1;
@@
E1 = os_snprintf(E2, E3, ...);
- if (\( E1 >= 0 \| E1 > 0 \) && \( (size_t) E1 < E3 \| E1 < (int) E3 \| E1 < E3 \))
+ if (!os_snprintf_error(E3, E1))
S1
Signed-off-by: Jouni Malinen <j@w1.fi>
This adds verification of os_snprintf() result against the maximum
buffer length. These changes were done automatically with spatch
using the following semantic patch:
@@
expression E1,E2,E3;
statement S1;
@@
E1 = os_snprintf(E2, E3, ...);
- if (\( E1 < 0 \| E1 <= 0 \))
+ if (os_snprintf_error(E3, E1))
(
S1
|
{ ... }
)
Signed-off-by: Jouni Malinen <j@w1.fi>
This reduced number of unnecessarily duplicated driver interface
callback functions for sending Action frames by using the more generic
send_action() instead of FT specific send_ft_action().
Signed-off-by: Jouni Malinen <j@w1.fi>
This helper function had not used the nl80211_set_iface_id() helper, but
there is no reason why it couldn't re-use the same helper as other
places using nl80211_cmd_msg().
Signed-off-by: Jouni Malinen <j@w1.fi>
Use the helper function to replace places that use nlmsg_alloc(),
nl80211_cmd(), and either bss->ifindex or if_nametoindex(bss->ifname).
Signed-off-by: Jouni Malinen <j@w1.fi>
bss->wdev_id_set is set for the non-detdev P2P Device, so
nl80211_cmd_msg() can be used as-is for these cases as well.
Signed-off-by: Jouni Malinen <j@w1.fi>
This removes duplicated code for building nl80211 commands for a BSS.
This commit handles the functions that were already using
nl80211_set_iface_id().
Signed-off-by: Jouni Malinen <j@w1.fi>
This gets rid of more NLA_PUT* macro uses in nl80211 to reduce the
number of functions that depend on the hidden behavior of jumping to the
nla_put_failure label.
Signed-off-by: Jouni Malinen <j@w1.fi>
This gets rid of NLA_PUT* macro use in checking nl80211 capabilities to
reduce the number of functions that depend on the hidden behavior of
jumping to the nla_put_failure label.
Signed-off-by: Jouni Malinen <j@w1.fi>
Suppose there are two APs (AP1 & AP2) and user attempted to connect to
AP2 before the previous connection with AP1 could succeed. Now, if the
connection event comes for the older AP with failed status, we should
just ignore it as the wpa_supplicant state has moved to "ASSOCIATING"
with the new AP (AP2).
This is a similar to the case where a disconnection event is ignored for
a case where local disconnect request can cause the extra event to show
up during the next association process following that command.
Signed-off-by: Jithu Jance <jithu@broadcom.com>
Using QCA vendor command, allow ACS function to be offloaded to the
driver. Once channels are selected, hostapd is notified to perform OBSS
operation.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
