This adds partial callbacks and events to allow P2P management to be
implemented in a driver/firmware. This is not yet complete and is
very much subject to change in the future.
With the new kernel functionality coming to Linux to allow off-channel
TX, we can take advantage of that in the P2P code that currently uses
remain-on-channel. If a driver advertises support for it, it will be
asked to handle off-channel TX by itself.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When controlling multiple virtual interfaces on the same physical
radio, share the scan results events with sibling interfaces. This
decreases the time it takes to connect many virtual interfaces.
This is currently only supported on Linux with cfg80211-based
drivers when using nl80211 or wext driver interface.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Some NDIS drivers require a workaround to allow them to associate
with a WPS AP that is already using protection (Privacy field = 1).
Let driver_ndis.c know if the AP is already using Privacy and if so,
configure a dummy WEP key to force the driver to associate.
There is no absolute requirement for separating address allocation
into separate functions, so simplify the driver wrapper interface
to use just if_add and if_remove instead of adding the new
alloc_interface_addr() and release_interface_addr() functions.
if_add() can now indicate if the driver forced a different interface
name or address on the virtual interface.
This can be used to test 802.11w by sending a protected or unprotected
deauth/disassoc frame.
hostapd_cli deauth <dst addr> test=<0/1>
hostapd_cli disassoc <dst addr> test=<0/1>
test=0: unprotected
test=1: protected
wpa_supplicant can now be notified of suspend/resume events, e.g.,
from pm-action scripts. This allows wpa_supplicant to clear information
that may become invalid during a suspend operation.
Most of this file was already moved into wpa_supplicant/scan.c and
we can remove the file completely by having couple of small helper
functions copied to the remaining users outside core wpa_supplicant
code.
This adds new commands and events for allowing off-channel Action
frame exchanges to be requested. This functionality is not yet used
and is only fully supported by driver_test.c at this point.
driver_nl80211.c has support for the remain-on-channel commands, but
the Action frame TX/RX part is still pending review for the kernel
code and as such, is not yet included here.
This adds placeholder code for allowing the virtual interfaces to be
pre-allocated a MAC address before the interface type is known with
drivers that do not handle interface type changes.
set_ap_wps_ie() is not used to set WPS IE for both Beacon and Probe
Response frames with a single call. In addition, struct wpabuf is used
instead of separate u8* and length fields. This avoids duplicated
allocation of the IEs and simplifies code in general.
This mode allows associated stations to use 4-address frames to allow
layer 2 bridging to be used. At least for the time being, this is only
supported with driver=nl80211.
IEEE 802.11w uses distinct key indexes (4 and 5) so the same
get_seqnum() handler can be used to fetch packet number for both
TKIP/CCMP and BIP(using IGTK).
Since the new get_seqnum_igtk() handler was not actually implemented by
any driver wrapper, this may also fix BIP/IGTK sequence number reporting
with driver_nl80211.c.
There was code for configuring this, but no driver wrapper actually
implements the actual setting. Remove this for now to reduce potential
confusion and to simply the driver interface.
if_add/if_remove can now be used as the generic driver ops for adding
and removing virtual interfaces of various types. In addition,
driver_nl80211.c is now including this code unconditionally, so that
the functions are not limited only for hostapd.
This makes it clearer which files are including header from src/common.
Some of these cases should probably be cleaned up in the future not to
do that.
In addition, src/common/nl80211_copy.h and wireless_copy.h were moved
into src/drivers since they are only used by driver wrappers and do not
need to live in src/common.
This gets rid of previously deprecated driver_ops handlers set_wpa,
set_drop_unencrypted, set_auth_alg, set_mode. The same functionality
can be achieved by using the init/deinit/associate handlers.
Clean up driver interface by merging hostapd and wpa_supplicant
specific set_beacon driver_ops into a single one. In addition,
merge set_beacon_int into to the same operation.
None of the driver wrappers user this. hostapd-controlled broadcast SSID
hiding can only be used with drivers that use hostapd for handling
Beacon and Probe Request/Response frames.
None of the driver wrappers use this. Only the drivers that use hostapd
for Beacon and Probe Request/Response handling can now use IEEE 802.11d
properly.
This was not really supported by any of the included driver wrappers. If
this functionality is desired in the future, this (or something similar)
can be added with the changes needed into a driver wrapper to use the
mechanism.
Instead of adding a new driver_ops for fetching neighbor BSS data (that
nl80211 driver interface had to scan during initialization), share the
same scan operations that wpa_supplicant is using. This gets rid of
duplicated scan code in driver_nl80211.c (and better yet, removes large
part of old WEXT code).
hostapd interface initialization is now completed in a callback, if
needed, i.e., he_features channel/hw_mode selection can use as much time
as needed. This can also help with radar detection in the future.
Use a parameter structure to pass in information that can be more easily
extended in the future. Include some of the parameters that were
previously read directly from hapd->conf in order to reduce need for
including hostapd/config.h into driver wrappers.
This merges the driver wrapper implementations to use the same
implementation both for hostapd and wpa_supplicant operations to avoid
code duplication.
This commit merges the driver_ops structures and implementations from
hostapd/driver*.[ch] into src/drivers. This is only an initial step and
there is room for number of cleanups to share code between the hostapd
and wpa_supplicant parts of the wrappers to avoid unnecessary source
code duplication.
This can be used, e.g., with mac80211-based Linux drivers with
nl80211. This allows over-the-air FT protocol to be used (IEEE
802.11r).
Since the nl80211 interface needed for this is very recent (added
today into wireless-testing.git), driver_nl80211.c has backwards
compatibility code that uses WEXT for association if the kernel does
not support the new commands. This compatibility code can be
disabled by defining NO_WEXT_COMPAT. That code will also be removed
at some point to clean up driver_nl80211.c.
This is just there very first step on being able to do something with
wireless LAN on Vista. There is some example code for requesting a scan,
but it does not work in its current form. Anyway, this adds a wpa_printf
noting that Native 802.11 drivers are not yet supported.
This is done with wired interfaces to fix IEEE 802.1X authentication
when the authenticator uses the group address (which should be happening
with wired Ethernet authentication).
This allows wpa_supplicant to complete wired authentication successfully
on Vista with a NDIS 6 driver, but the change is likely needed for
Windows XP, too.
Do not use just the driver name for this since driver_ndis.c supports
both wired and wireless NDIS drivers and needs to indicate the driver
type after initialization.
This can be used to provide support for scanning multiple SSIDs at a
time to optimize scan_ssid=1 operations. In addition, Probe Request IEs
will be available to scan2() (e.g., for WPS PBC scanning).
