IPMK and CMK are derived from TK when using TLS session resumption with
PEAPv0 crypto binding. The EAP-PEAP peer implementation already
supported this, but the server side did not.
Signed-off-by: Jouni Malinen <j@w1.fi>
eap_peap_parse_phase1() returned 0 unconditionally, so there was no need
for that return value or the code path that tried to address the error
case.
Signed-off-by: Jouni Malinen <j@w1.fi>
On systems that have multiple WLAN rfkill instances, the rfkill code
can become confused into thinking that the device was unblocked when
in fact it wasn't, because it only matches on the WLAN type.
Since it then stores the new (unblocked) state from the wrong rfkill
instance, it will never retry the failing IFF_UP operation and the
user has to toggle rfkill again, or otherwise intervene manually, in
this case to get back to operational state.
Fix this by using the existing (but unused) ifname argument when the
rfkill instance is created to match to a specific rfkill index only.
As a P2P Device interface does not have a netdev interface associated
with it, use the name of a sibling interface to initialize the rfkill
context for the P2P Device interface. For nl80211, as the wiphy index
is known only after getting the driver capabilities from the kernel,
move the initialization of the rfkill object to
wpa_driver_nl80211_finish_drv_init().
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
The rfkill processing in nl80211 driver assumes that the
INTERFACE_ENABLED/DISABLED will be also issued, so does not do much in
the rfkill callbacks. However, as a P2P Device interface is not
associated with a network interface, these events are not issued for it.
Handle rfkill events for the P2P_DEVICE interface by faking the
INTERFACE_ENABLED/DISABLED.
Signed-off-by: Moshe Benji <Moshe.Benji@intel.com>
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
The Setup Response timer is relatively fast (500 ms) and there are
instances where it fires on the responder side after the initiator has
already sent out the TDLS Setup Confirm frame. Prevent the processing of
this stale TDLS Setup Response frame on the initiator side.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Fix mostly theoretical NULL pointer dereference in
wpa_debug_open_linux_tracing() if /proc/mounts were to return a
malformed line.
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
This patch fixes an issue with an invalid phase2 parameter value
auth=MSCHAPv2 getting interpreted as auth=MSCHAP (v1) which could
degrade security (though, only within a protected TLS tunnel). Now when
invalid or unsupported auth= phase2 parameter combinations are
specified, EAP-TTLS initialization throws an error instead of silently
doing something.
More then one auth= phase2 type cannot be specified and also both auth= and
autheap= options cannot be specified.
Parsing phase2 type is case sensitive (as in other EAP parts), so phase2
parameter auth=MSCHAPv2 is invalid. Only auth=MSCHAPV2 is correct.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
[Use cstr_token() to get rid of unnecessary allocation; cleanup]
Signed-off-by: Jouni Malinen <j@w1.fi>
There are two types of memory processing functions in the file
atheros_driver.c, such as memory and os_memory. Unify the processing
functions into one type which has the prefix "os_".
Signed-off-by: Matt Woods <matt.woods@aliyun.com>
This adds a CTRL-EVENT-EAP-TLS-CERT-ERROR and CTRL-EVENT-EAP-STATUS
messages with 'bad certificate status response' for cases where no valid
OCSP response was received, but the network profile requires OCSP to be
used.
Signed-off-by: Jouni Malinen <j@w1.fi>
This completes OCSP stapling support on the TLS client side. Each
SingleResponse value is iterated until a response matching the server
certificate is found. The validity time of the SingleResponse is
verified and certStatus good/revoked is reported if all validation step
succeed.
Signed-off-by: Jouni Malinen <j@w1.fi>
This adds the next step in completing TLS client support for OCSP
stapling. The BasicOCSPResponse is parsed, a signing certificate is
found, and the signature is verified. The actual sequence of OCSP
responses (SignleResponse) is not yet processed in this commit.
Signed-off-by: Jouni Malinen <j@w1.fi>
This adds the next step for OCSP stapling. The received OCSPResponse is
parsed to get the BasicOCSPResponse. This commit does not yet process
the BasicOCSPResponse.
Signed-off-by: Jouni Malinen <j@w1.fi>
This allows the internal TLS client implementation to accept
CertificateStatus message from the server when trying to use OCSP
stapling. The actual OCSPResponse is not yet processed in this commit,
but the CertificateStatus message is accepted to allow the TLS handshake
to continue.
Signed-off-by: Jouni Malinen <j@w1.fi>
This allows the internal TLS implementation to request server
certificate status using OCSP stapling. This commit is only adding code
to add the request. The response is not yet used.
Signed-off-by: Jouni Malinen <j@w1.fi>
This prints the received ServerHello extensions into the debug log and
allows handshake to continue even if such extensions are included.
Signed-off-by: Jouni Malinen <j@w1.fi>
This allows the internal TLS implementation to parse a private key and a
certificate from a PKCS #12 file protected with
pbeWithSHAAnd3-KeyTripleDES-CBC.
Signed-off-by: Jouni Malinen <j@w1.fi>
This adds support for decrypting private keys protected with the old
PKCS #12 mechanism using OID pbeWithSHAAnd3-KeyTripleDES-CBC.
Signed-off-by: Jouni Malinen <j@w1.fi>
This adds support for optional functionality to validate server
certificate chain in TLS-based EAP methods in an external program.
wpa_supplicant control interface is used to indicate when such
validation is needed and what the result of the external validation is.
This external validation can extend or replace the internal validation.
When ca_cert or ca_path parameter is set, the internal validation is
used. If these parameters are omitted, only the external validation is
used. It needs to be understood that leaving those parameters out will
disable most of the validation steps done with the TLS library and that
configuration is not really recommend.
By default, the external validation is not used. It can be enabled by
addingtls_ext_cert_check=1 into the network profile phase1 parameter.
When enabled, external validation is required through the CTRL-REQ/RSP
mechanism similarly to other EAP authentication parameters through the
control interface.
The request to perform external validation is indicated by the following
event:
CTRL-REQ-EXT_CERT_CHECK-<id>:External server certificate validation needed for SSID <ssid>
Before that event, the server certificate chain is provided with the
CTRL-EVENT-EAP-PEER-CERT events that include the cert=<hexdump>
parameter. depth=# indicates which certificate is in question (0 for the
server certificate, 1 for its issues, and so on).
The result of the external validation is provided with the following
command:
CTRL-RSP-EXT_CERT_CHECK-<id>:<good|bad>
It should be noted that this is currently enabled only for OpenSSL (and
BoringSSL/LibreSSL). Due to the constraints in the library API, the
validation result from external processing cannot be reported cleanly
with TLS alert. In other words, if the external validation reject the
server certificate chain, the pending TLS handshake is terminated
without sending more messages to the server.
Signed-off-by: Jouni Malinen <j@w1.fi>
Do not override the parsing error with the "PAC block not terminated
with END" message if the reason for the END line not yet being seen is
in failure to parse an earlier line.
Signed-off-by: Jouni Malinen <j@w1.fi>
It was possible to hit a NULL pointer dereference if Session-Id
derivation failed due to a memory allocation failure.
Signed-off-by: Jouni Malinen <j@w1.fi>
The EVP_MD_CTX and HMAC_CTX definitions are now hidden from applications
using OpenSSL. Fix compilation issues with OpenSSL 1.1.x-pre1 by using
the new API for allocating these structures.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This FTIE needs to be an exact copy of the one in (Re)Association
Response frame. Copy the stored element rather than building a new copy
that would not have the correct MIC value. This is needed to fix PTK
rekeying after FT protocol run.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The FTIE from (Re)Association Response frame was copied before
calculating the MIC. This resulted in incorrect value being used when
comparing the EAPOL-Key msg 2/4 value in case PTK rekeying was used
after FT protocol run. Fix this by storing the element after the MIC
field has been filled in.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
wpa_insert_pmkid() did not support cases where the original RSN IE
included any PMKIDs. That case can happen when PTK rekeying through
4-way handshake is used after FT protocol run. Such a 4-way handshake
used to fail with wpa_supplicant being unable to build the EAPOL-Key msg
2/4.
Fix this by extending wpa_insert_pmkid() to support removal of the old
PMKIDs, if needed.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This makes it easier to interpret AP side debug log for a case where a
station specifies in unsupported management group cipher.
Signed-off-by: Jouni Malinen <j@w1.fi>
The new wpa_supplicant control interface command "TEST_ASSOC_IE
<hexdump>" can now be used to override the WPA/RSN IE for Association
Request frame and following 4-way handshake to allow protocol testing of
AP side processing of WPA/RSN IE.
Signed-off-by: Jouni Malinen <j@w1.fi>
This extends the internal TLS support for PKCS #5 v2.0 PBES2 private key
format with des-ede3-cbc encryption and PBKDF2 SHA-1.
Signed-off-by: Jouni Malinen <j@w1.fi>
This adds experimental support for using OCSP with libcurl that is built
against BoringSSL. This needs small modifications to libcurl to allow
CURLOPT_SSL_VERIFYSTATUS to be used to call
SSL_enable_ocsp_stapling(connssl->handle) in ossl_connect_step1().
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This makes it easier to share the OCSP implementation needed for
BoringSSL outside tls_openssl.c. For now, this is mainly for
http_curl.c.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
BoringSSL modified the struct sha_state_st (SHA_CTX) definition by
converting h0..h4 with h[5] array. This broke wpa_supplicant/hostapd
build with EAP-SIM enabled. BoringSSL restored the old version for
ANDROID builds, but only the new version is currently defined for
non-Android cases. For now, fix this by having matching selection in
fips_prf_openssl.c based on OPENSSL_IS_BORINGSSL and ANDROID defines.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
OpenSSL 1.1.x will apparently go out with "SSLeay" renamed in the API to
"OpenSSL", which broke the build here for fetching the version of the
running OpenSSL library when wpa_supplicant/hostapd is built against the
current OpenSSL snapshot.
Signed-off-by: Jouni Malinen <j@w1.fi>
These needs to be cancelled so that the kernel driver does not get left
with all old entries blocking other offchannel operations.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This allows multiple external registrars to execute a WPS protocol run
with a WPS AP over UPnP. Previously, hostapd supported only a single WPS
peer entry at a time and if multiple ERs tried to go through a WPS
protocol instance concurrently, only one such exchange could succeed.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add 'scan plans' to driver scan parameters for scheduled scan.
Each 'scan plan' specifies the number of iterations to run the scan
request and the interval between iterations. When a scan plan
finishes (i.e., it was run for the specified number of iterations),
the next scan plan is executed. The last scan plan will run
infinitely.
The maximum number of supported scan plans, the maximum number of
iterations for a single scan plan and the maximum scan interval
are advertised by the driver.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
conn->session_resumed was not set to 1 after successful use of a TLS
session ticket with EAP-FAST. This resulted in the wpa_supplicant STATUS
tls_session_reused showing incorrect value (0 instead of 1) when
EAP-FAST PAC was used. Fix this by setting conn->session_resumed = 1
when TLS handshake using the session ticket succeeds.
Signed-off-by: Jouni Malinen <j@w1.fi>
Commit af851914f8 ('Make
tls_connection_get_keyblock_size() internal to tls_*.c') broke
tls_connection_prf() with the internal TLS implementation when using
skip_keyblock=1. In practice, this broke EAP-FAST. Fix this by deriving
the correct number of PRF bytes before skipping the keyblock.
Signed-off-by: Jouni Malinen <j@w1.fi>
If the server/client certificate includes the extKeyUsage extension,
verify that the listed key purposes include either the
anyExtendedKeyUsage wildcard or id-kp-serverAuth/id-kp-clientAuth,
respectively.
Signed-off-by: Jouni Malinen <j@w1.fi>
md4_vector(), md5_vector(), sha1_vector(), and sha256_vector() already
supported TEST_FAIL() with the OpenSSL crypto implementation, but the
same test functionality is needed for the internal crypto implementation
as well.
Signed-off-by: Jouni Malinen <j@w1.fi>
It was possible for some NFC DH generation error paths to leak memory
since the old private/public key was not freed if an allocation failed.
Signed-off-by: Jouni Malinen <j@w1.fi>
The internal TLS client implementation in wpa_supplicant can now be used
with the phase2 parameters tls_disable_tlsv1_0=1, tls_disable_tlsv1_1=1,
and tls_disable_tlsv1_2=1 to disable the specified TLS version(s).
Signed-off-by: Jouni Malinen <j@w1.fi>
This makes it simpler to add support for new TLS_CONN_* flags without
having to add a new configuration function for each flag.
Signed-off-by: Jouni Malinen <j@w1.fi>
This allows wpa_supplicant to return eap_tls_version STATUS information
when using the internal TLS client implementation.
Signed-off-by: Jouni Malinen <j@w1.fi>
The internal TLS client implementation can now be used with
ca_cert="probe://" to probe the server certificate chain. This is also
adding the related CTRL-EVENT-EAP-TLS-CERT-ERROR and
CTRL-EVENT-EAP-PEER-CERT events.
Signed-off-by: Jouni Malinen <j@w1.fi>
This extends the internal TLS client implementation to support signature
algorithms SHA384 and SHA512 in addition to the previously supported
SHA256.
Signed-off-by: Jouni Malinen <j@w1.fi>
Since we support only SHA256 (and not the default SHA1) with TLS v1.2,
the signature_algorithms extensions needs to be added into ClientHello.
This fixes interop issues with the current version of OpenSSL that uses
the default SHA1 hash if ClientHello does not specify allowed signature
algorithms.
Signed-off-by: Jouni Malinen <j@w1.fi>
This commit adds support for validating certificates with SHA384 and
SHA512 hashes. Those certificates are now very common so wpa_supplicant
needs support for them.
SHA384 and SHA512 hash functions are included in the previous commit.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
These will be used with the internal TLS implementation to extend hash
algorithm support for new certificates and TLS v1.2.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
This commit adds support for "hash://server/sha256/cert_hash_in_hex"
scheme in ca_cert property for the internal TLS implementation.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
In documentation is written: "If ca_cert and ca_path are not included,
server certificate will not be verified". This is the case when
wpa_supplicant is compiled with OpenSSL library, but when using the
internal TLS implementation and some certificates in CA chain are in
unsupported format (e.g., use SHA384 or SHA512 hash functions) then
verification fails even if ca_cert property is not specified.
This commit changes behavior so that certificate verification in
internal TLS implementation is really skipped when ca_cert is not
specified.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
If init_for_reauth fails, the EAP-SIM peer state was not freed properly.
Use eap_sim_deinit() to make sure all allocations get freed. This could
be hit only if no random data could be derived for NONCE_MT.
Signed-off-by: Jouni Malinen <j@w1.fi>
This adds the driver interface commands for issuing a request to abort
an ongoing scan operation.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
NL80211_CMD_GET_STATION does not work with the IBSS/mesh BSSID, so clear
the signal strength instead of returning failure when SIGNAL_POLL is
used in an IBSS/mesh.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The new max_oper_chwidth and freq2 arguments to P2P_CONNECT, P2P_INVITE,
and P2P_GROUP_ADD control interface commands can be used to request
larger VHT operating channel bandwidth to be used than the previously
used maximum 80 MHz.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This extends the previous design that covered only the VHT 80 MHz cases
for VHT channel flags. New functions are introduced to allow 160 MHz
bandwidth cases to determine the center channel and check availability
of a 160 MHz channel.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This adds definitions for the global operating classes 129 and 130 for
VHT 80+80 MHz and 160 MHz use cases.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Modify the FST peer connection check so it won't skip peers without MB
IEs making it more permissive for peers that didn't provide MB IEs
during association request. This can be helpful, e.g., in cases where a
STA's interface connected before it was added to the FST group. This
allows the AP to receive FST Action frames and initiate session with a
STA via STA's interface that doesn't expose MB IEs.
The adjusted FST protocol is still safe, as it protects itself in many
other ways (checking band info and it's accordance to the interfaces,
Setup IDs, connection states of the interfaces involved, etc.)
effectively avoiding all types of invalid situations.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The old wpa_supplicant/Makefile target test-eap_sim_common did not work
anymore and anyway, this test is better placed in the newer hwsim
framework to make sure the test case gets executed automatically.
Signed-off-by: Jouni Malinen <j@w1.fi>
Number of places were calling functions that are not included in
CONFIG_NO_WPA=y build anymore. Comment out such calls. In addition, pull
in SHA1 and MD5 for config_internal.c, if needed.
Signed-off-by: Jouni Malinen <j@w1.fi>
FST STA should always expose its MB IEs regardless of its connection
state and whether the connected AP is currently FST-enabled or not.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
When built with browser-android.c, hs20-osu-client used to always launch
the native/stock Android browser for OSU user interaction. This browser
is not present in all devices. It is better to give the option to the
user to select his/her browser.
Here the user will be shown a pop up to select the browser that he/she
wants.
Signed-off-by: Somdas Bandyopadhyay <somdas.bandyopadhyay@intel.com>
When an AP interface it created, it is also setup and subscribes
for management frames etc. However, when the interface is added by
wpa_supplicant, setting up for AP operations is redundant because
it will be done by wpa_supplicant on wpa_drv_init() when setting
the interface mode to AP.
In addition, it may cause wpa_supplicant to fail initializing the
interface as it will try to subscribe for management frames on this
interface but the interface is already registered.
Change this, so when adding an AP interface, make setting up the AP
optional, and use it only when the interface is added by hostapd but not
when it is added by wpa_supplicant.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
LibreSSL does not yet support the new API, so do not use it
when LIBRESSL_VERSION_NUMBER macro is defined.
Signed-off-by: Marek Behun <kabel@blackhole.sk>
When an AP is started on the 5.2 GHz band with 40 MHz bandwidth, a
scan is issued in order to handle 20/40 MHz coexistence. However,
the scan is issued even if iface->conf->no_pri_sec_switch is set,
which is redundant.
Fix this by checking iface->conf->no_pri_sec_switch before starting
the scan.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
The de-authentication flow in wpa_driver_nl80211_deauthenticate() can
result in a locally generated de-authentication event. To avoid getting
this extra event ignore_next_local_deauth flag is set, and should be
cleared when the next local deauth event is received. However, it is not
cleared when the event shows up after the wpa_supplicant has started a
connection with a new AP, and as a result it might ignore future
deauth event from the driver.
Fix this by clearing the flag if the event is locally generated.
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
The authentication flow in wpa_driver_nl80211_authenticate() can
result in a locally generated de-authentication, in which both
next_local_deauth and ignore_next_local_deauth are set.
However, in mlme_event_deauth_disassoc(), when ignore_deauth_event is
set, the flag is cleared, but the flow immediately returns leaving
ignore_next_local_deauth set, which can result in ignoring future deauth
event from the driver, leaving the wpa_supplicant in an inconsistent
state.
Fix this by clearing both flags in case that next_local_deauth is set.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
This allows offloaded roaming to inform user space of the change in IP
subnet post roaming. The device may have roamed to a network which is in
a different subnet which will result in IP connectivity loss. Indicating
the change in subnet enables the user space to refresh the IP address or
to perform IP subnet validation if unknown status is indicated.
The driver indication is reported with a new event from wpa_supplicant
in the following format:
CTRL-EVENT-SUBNET-STATUS-UPDATE status=<0/1/2>
where
0 = unknown
1 = IP subnet unchanged (can continue to use the old IP address)
2 = IP subnet changed (need to get a new IP address)
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The EAP peer state machine moved from IDLE to FAILURE state when the
EAPOL Authenticator triggered reauthentication with an
EAP-Request/Identity in a case where the associated started with FT
protocol or offloaded PMKSA cache use (4-way handshake using a
previously acquired PMK). This happened due to the altSuccess=TRUE
setting being left behind and not cleared when processing the restart of
authentication. Fix this by clearing altAccept and eapSuccess when going
through SUPP_PAE RESTART state.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The EAPOL AUTH_PAE state machine was left in incomplete state at the
completion of FT protocol. Set portValid = TRUE to allow the state
machine to proceed from AUTHENTICATING to AUTHENTICATED state, so that a
new EAPOL reauthentication can be triggered.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
If a memory allocation fails while parsing driver capabilities, drop all
mode/channel/rate information instead of returning possibly partial
information.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Now hostapd will use station MAC-based permissions according to the
macaddr_acl policy also for drivers which use AP SME offload, but do not
support NL80211_CMD_SET_MAC_ACL for offloading MAC ACL processing. It
should be noted that in this type of case the association goes through
and the station gets disconnected immediately after that.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
wpa_sm_key_mgmt_set_pmk() was checking for proactive_key_caching to be
enabled before setting the PMK to the driver. This check is not required
and would mandate configuration setting of okc or proactive_key_caching
for cases which were not necessary.
Signed-off-by: Amarnath Hullur Subramanyam <amarnath@qca.qualcomm.com>
The new attribute can be used with
QCA_NL80211_VENDOR_SUBCMD_KEY_MGMT_ROAM_AUTH to indicate whether the IP
subnet was detected to have changed when processing offloaded roam/key
management.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
If the Confirm message is received from the server before the Identity
exchange has been completed, the group has not yet been determined and
data->grp is NULL. The error path in eap_pwd_perform_confirm_exchange()
did not take this corner case into account and could end up
dereferencing a NULL pointer and terminating the process if invalid
message sequence is received. (CVE-2015-5316)
Signed-off-by: Jouni Malinen <j@w1.fi>
All but the last fragment had their length checked against the remaining
room in the reassembly buffer. This allowed a suitably constructed last
fragment frame to try to add extra data that would go beyond the buffer.
The length validation code in wpabuf_put_data() prevents an actual
buffer write overflow from occurring, but this results in process
termination. (CVE-2015-5314)
Signed-off-by: Jouni Malinen <j@w1.fi>
All but the last fragment had their length checked against the remaining
room in the reassembly buffer. This allowed a suitably constructed last
fragment frame to try to add extra data that would go beyond the buffer.
The length validation code in wpabuf_put_data() prevents an actual
buffer write overflow from occurring, but this results in process
termination. (CVE-2015-5315)
Signed-off-by: Jouni Malinen <j@w1.fi>
Using "STATUS" command triggers CTRL-EVENT-STATE-CHANGE and
CTRL-EVENT-CONNECTED (if connected to some AP) events. These events
cause problems in Android WifiStateMachine in Marshmallow. Due to these
events WifiStateMachine sometimes disconnects the OSU SSID connection,
while hs20-osu-client waits for IP address.
Signed-off-by: Somdas Bandyopadhyay <somdas.bandyopadhyay@intel.com>
Some APs may send RSC octets in EAPOL-Key message 3 of 4-Way Handshake
or in EAPOL-Key message 1 of Group Key Handshake in the opposite byte
order (or by some other corrupted way). Thus, after a successful
EAPOL-Key exchange the TSC values of received multicast packets, such as
DHCP, don't match the RSC one and as a result these packets are dropped
on replay attack TSC verification. An example of such AP is Sapido
RB-1732.
Work around this by setting RSC octets to 0 on GTK installation if the
AP RSC value is identified as a potentially having the byte order issue.
This may open a short window during which older (but valid)
group-addressed frames could be replayed. However, the local receive
counter will be updated on the first received group-addressed frame and
the workaround is enabled only if the common invalid cases are detected,
so this workaround is acceptable as not decreasing security
significantly. The wpa_rsc_relaxation global configuration property
allows the GTK RSC workaround to be disabled if it's not needed.
Signed-off-by: Max Stepanov <Max.Stepanov@intel.com>
While this is not part of RFC 4137, the way m.check(eapReqData) is
implemented in wpa_supplicant allows an EAP method to not update the
ignore value even though each such call is really supposed to get a new
response. It seems to be possible to hit a sequence where a previous EAP
authentication attempt terminates with sm->ignore set from the last
m.check() call and the following EAP authentication attempt could fail
to go through the expected code path if it does not clear the ignore
flag. This is likely only hit in some error cases, though. The hwsim
test cases could trigger this with the following sequence:
eap_proto_ikev2 ap_wps_m1_oom
Signed-off-by: Jouni Malinen <j@w1.fi>
When using CONFIG_TLS=internal and starting hostapd with multiple
configuration files that each initialize TLS server, the server
certificate and related data was not freed for all the interfaces on
exit path. Fix this by freeing the credential data that is stored
separately for each call to tls_init().
Signed-off-by: Jouni Malinen <j@w1.fi>
Expire pending DB request for EAP-SIM/AKA/AKA'. Timeout defaults to 1
second and is user configurable in hostapd.conf (eap_sim_db_timeout).
Signed-off-by: Frederic Leroy <frederic.leroy@b-com.com>
This extends ieee80211_freq_to_channel_ext() with knowledge of the
operating classes for the 5 GHz channels 100..140.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Provide information on whether EAPOL-Key frame was sent successfully to
kernel for transmittion. wpa_eapol_key_send() will return
>= 0 on success and < 0 on failure. After receiving EAPOL-Key msg 3/4,
wpa_supplicant sends EAPOL-Key msg 4/4 and shows CTRL-EVENT-CONNECTED
only after verifying that the msg 4/4 was sent to kernel for
transmission successfully.
Signed-off-by: Avichal Agarwal <avichal.a@samsung.com>
Signed-off-by: Kyeong-Chae Lim <kcya.lim@samsung.com>
When multiple interfaces across mutiple radios are started using a
single instance of hostapd, they all come up at different times
depending upon how long the ACS and HT scan take on each radio. This
will result in stations (that already have the AP profile) associating
with the first interfaces that comes up. For example in a dual band
radio case (2G and 5G) with ACS enabled, 2G always comes up first
because the ACS scan takes less time on 2G and this results in all
stations associating with the 2G interface first.
This feature brings up all the interfaces at the same time. The list of
interfaces specified via hostapd.conf files on the command line are all
marked as sync interfaces. All the interfaces are synchronized in
hostapd_setup_interface_complete().
This feature is turned on with '-S' commmand line option.
Signed-off-by: Srinivasa Duvvuri <sduvvuri@chromium.org>
Assign nl80211vendor commands QCA_NL80211_VENDOR_SUBCMD_OTA_TEST and
QCA_NL80211_VENDOR_SUBCMD_SET_TXPOWER_SCALE as well as corresponding
attributes.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
P2P device discovery can add peer entries based on a message directly
from a peer and from a Probe Response frame from a GO for all the P2P
Clients in the group. The former case for filtering out control
characters from the device name while the latter was not. Make this
consistent and filter both cases in the same way to avoid confusing
external programs using the device name of a P2P peer.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
There is no point in sending TPK M3 (TDLS Setup Confirm) with a failure
status if the first transmission attempt fails. Instead, just return a
failure by disabling the link rather than retransmitting the TPK M3
frame with an error status.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
hmac_sha256_kdf() got pulled in only if CONFIG_ERP=y is set. Fix
test_sha256() by making the test case conditional on the function being
present.
Signed-off-by: Jouni Malinen <j@w1.fi>
wpa_debug_reopen_file() used to write an error message at MSG_ERROR
level if it was called with last_path == NULL (the last debug log file
path not known). This is not a fatal error, but a normal case if
wpa_debug_open_file() has not been used. Remove the error message and
return success in such case.
Signed-off-by: Jouni Malinen <j@w1.fi>
Linux packet socket workaround(*) has an impact in performance when the
workaround socket needs to be kept open to receive EAPOL frames. While
this is normally avoided with a kernel that has the issue addressed by
closing the workaround packet socket when detecting a frame through the
main socket, it is possible for that mechanism to not be sufficient,
e.g., when an open network connection (no EAPOL frames) is used.
Add a build option (CONFIG_NO_LINUX_PACKET_SOCKET_WAR=y) to disable the
workaround. This build option is disabled by default and can be enabled
explicitly on distributions which have an older kernel or a fix for the
kernel regression.
Also remove the unused variable num_rx.
(*) Linux kernel commit 576eb62598f10c8c7fd75703fe89010cdcfff596
('bridge: respect RFC2863 operational state') from 2012 introduced a
regression for using wpa_supplicant with EAPOL frames and a station
interface in a bridge.
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Reorder terms in a way that no invalid pointers are generated with
pos+len operations. end-pos is always defined (with a valid pos pointer)
while pos+len could end up pointing beyond the end pointer which would
be undefined behavior.
Signed-off-by: Jouni Malinen <j@w1.fi>
Reorder terms in a way that no invalid pointers are generated with
pos+len operations. end-pos is always defined (with a valid pos pointer)
while pos+len could end up pointing beyond the end pointer which would
be undefined behavior.
Signed-off-by: Jouni Malinen <j@w1.fi>
Reorder terms in a way that no invalid pointers are generated with
pos+len operations. end-pos is always defined (with a valid pos pointer)
while pos+len could end up pointing beyond the end pointer which would
be undefined behavior.
Signed-off-by: Jouni Malinen <j@w1.fi>
Reorder terms in a way that no invalid pointers are generated with
pos+len operations. end-pos is always defined (with a valid pos pointer)
while pos+len could end up pointing beyond the end pointer which would
be undefined behavior.
Signed-off-by: Jouni Malinen <j@w1.fi>
Reorder terms in a way that no invalid pointers are generated with
pos+len operations. end-pos is always defined (with a valid pos pointer)
while pos+len could end up pointing beyond the end pointer which would
be undefined behavior.
Signed-off-by: Jouni Malinen <j@w1.fi>
Reorder terms in a way that no invalid pointers are generated with
pos+len operations. end-pos is always defined (with a valid pos pointer)
while pos+len could end up pointing beyond the end pointer which would
be undefined behavior.
Signed-off-by: Jouni Malinen <j@w1.fi>
Reorder terms in a way that no invalid pointers are generated with
pos+len operations. end-pos is always defined (with a valid pos pointer)
while pos+len could end up pointing beyond the end pointer which would
be undefined behavior.
Signed-off-by: Jouni Malinen <j@w1.fi>
Reorder terms in a way that no invalid pointers are generated with
pos+len operations. end-pos is always defined (with a valid pos pointer)
while pos+len could end up pointing beyond the end pointer which would
be undefined behavior.
Signed-off-by: Jouni Malinen <j@w1.fi>
Reorder terms in a way that no invalid pointers are generated with
pos+len operations. end-pos is always defined (with a valid pos pointer)
while pos+len could end up pointing beyond the end pointer which would
be undefined behavior.
Signed-off-by: Jouni Malinen <j@w1.fi>
Reorder terms in a way that no invalid pointers are generated with
pos+len operations. end-pos is always defined (with a valid pos pointer)
while pos+len could end up pointing beyond the end pointer which would
be undefined behavior.
Signed-off-by: Jouni Malinen <j@w1.fi>
Reorder terms in a way that no invalid pointers are generated with
pos+len operations. end-pos is always defined (with a valid pos pointer)
while pos+len could end up pointing beyond the end pointer which would
be undefined behavior.
Signed-off-by: Jouni Malinen <j@w1.fi>
Reorder terms in a way that no invalid pointers are generated with
pos+len operations. end-pos is always defined (with a valid pos pointer)
while pos+len could end up pointing beyond the end pointer which would
be undefined behavior.
Signed-off-by: Jouni Malinen <j@w1.fi>
Reorder terms in a way that no invalid pointers are generated with
pos+len operations. end-pos is always defined (with a valid pos pointer)
while pos+len could end up pointing beyond the end pointer which would
be undefined behavior.
Signed-off-by: Jouni Malinen <j@w1.fi>
Reorder terms in a way that no invalid pointers are generated with
pos+len operations. end-pos is always defined (with a valid pos pointer)
while pos+len could end up pointing beyond the end pointer which would
be undefined behavior.
Signed-off-by: Jouni Malinen <j@w1.fi>
Reorder terms in a way that no invalid pointers are generated with
pos+len operations. end-pos is always defined (with a valid pos pointer)
while pos+len could end up pointing beyond the end pointer which would
be undefined behavior.
Signed-off-by: Jouni Malinen <j@w1.fi>
Reorder terms in a way that no invalid pointers are generated with
pos+len operations. end-pos is always defined (with a valid pos pointer)
while pos+len could end up pointing beyond the end pointer which would
be undefined behavior.
Signed-off-by: Jouni Malinen <j@w1.fi>
Reorder terms in a way that no invalid pointers are generated with
pos+len operations. end-pos is always defined (with a valid pos pointer)
while pos+len could end up pointing beyond the end pointer which would
be undefined behavior.
Signed-off-by: Jouni Malinen <j@w1.fi>
Reorder terms in a way that no invalid pointers are generated with
pos+len operations. end-pos is always defined (with a valid pos pointer)
while pos+len could end up pointing beyond the end pointer which would
be undefined behavior.
Signed-off-by: Jouni Malinen <j@w1.fi>
Reorder terms in a way that no invalid pointers are generated with
pos+len operations. end-pos is always defined (with a valid pos pointer)
while pos+len could end up pointing beyond the end pointer which would
be undefined behavior.
Signed-off-by: Jouni Malinen <j@w1.fi>
Reorder terms in a way that no invalid pointers are generated with
pos+len operations. end-pos is always defined (with a valid pos pointer)
while pos+len could end up pointing beyond the end pointer which would
be undefined behavior.
Signed-off-by: Jouni Malinen <j@w1.fi>
Reorder terms in a way that no invalid pointers are generated with
pos+len operations. end-pos is always defined (with a valid pos pointer)
while pos+len could end up pointing beyond the end pointer which would
be undefined behavior.
Signed-off-by: Jouni Malinen <j@w1.fi>
Reorder terms in a way that no invalid pointers are generated with
pos+len operations. end-pos is always defined (with a valid pos pointer)
while pos+len could end up pointing beyond the end pointer which would
be undefined behavior.
Signed-off-by: Jouni Malinen <j@w1.fi>
hmac_sha256() and hmac_sha256_vector() return a result code now, so use
that return value to terminate HMAC-SHA256-based GKDF/MIC similarly to
what was already done with the CMAC-based GKDF/MIC.
Signed-off-by: Jouni Malinen <j@w1.fi>
The recently added ProxyARP support (proxy_arp=1) in hostapd allows a
STA IPv4 address to be learned from DHCP or ARP messages. If that
information is available, add it to Account-Request messages in
Framed-IP-Address attribute.
Signed-off-by: Jouni Malinen <j@w1.fi>
The new hostapd configuration parameter no_probe_resp_if_max_sta=1 can
be used to request hostapd not to reply to broadcast Probe Request
frames from unassociated STA if there is no room for additional stations
(max_num_sta). This can be used to discourage a STA from trying to
associate with this AP if the association would be rejected due to
maximum STA limit.
Signed-off-by: Jouni Malinen <j@w1.fi>
If hostapd or wpa_supplicant is built from a git repository, add a
VERSION_STR postfix from the current git branch state. This is from "git
describe --dirty=+". VERSION_STR will thus look something like
"2.6-devel-hostap_2_5-132-g4363c0d+" for development builds from a
modified repository.
This behavior is enabled automatically if a build within git repository
is detected (based on ../.git existing). This can be disabled with
CONFIG_NO_GITVER=y in wpa_supplicant/.config and hostapd/.config.
Signed-off-by: Jouni Malinen <j@w1.fi>
On TPK lifetime expiration, tear down the direct link before renewing
the link in the case of TDLS initiator processing. The expired key
cannot be used anymore, so it is better to explicitly tear down the old
link first.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This improves robustness of GO Negotiation in special cases where GO
Negotiation Request frames from the peer may end up getting delivered
multiple times, e.g., due to interference and retransmitted frames not
getting properly filtered out in duplicate detection (which is something
that number of drivers do not implement for pre-associated state).
If we have already replied with GO Negotiation Response frame with
Status 1 (not yet ready), do not reply to another GO Negotiation Request
frame from the peer if we have already received authorization from the
user (P2P_CONNECT command) for group formation and have sent out our GO
Negotiation Request frame. This avoids a possible sequence where two
independent GO Negotiation instances could go through in parallel if the
MAC address based rule on avoiding duplicate negotiations is not able to
prevent the case. This can allow GO Negotiation to complete successfully
whereas the previous behavior would have likely resulted in a failure
with neither device sending a GO Negotiation Confirm frame.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Some drivers (like mac80211) do not accept changing the TX bitrate mask
before the network interface is up. Thus, calling
nl80211_disable_11b_rates() before the interface is up fails, and the
P2P network interface continues to use invalid bitrates.
To fix this call nl80211_disable_11b_rates() immediately after the
interface is brought up (and also after rfkill is unblocked).
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
While testing, I noticed that printf_encode() makes control characters
human-readable, with one exemption, the DEL character (ASCII 127).
Assuming this exemption was unintentional, make it appear as an escaped
\x7f instead of a literal DEL character in the output.
Signed-off-by: Josh Lehan <krellan@krellan.net>
atheros_set_opt_ie() needs to be called before freeing drv->wpa_ie to
avoid hitting double-free on the deinit path. Similarly,
drv->wps_beacon_ie and drv->wps_probe_resp_ie could have been used after
being freed. Fix these be moving the atheros_set_opt_ie() call in
atheros_deinit().
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
It is possible for a driver to support sufficient number of channels to
hit the previous limit of 200 characters for the "nl80211: Scan included
frequencies:" debug message. Increase the maximum buffer length to 300
characters to allow more complete list of scanned frequencies to be
written into the debug log. This limit is more in line with the
MAX_REPORT_FREQS (50) limit.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
In addition to the PTK length increasing, the length of the PMK was
increased (from 256 to 384 bits) for the 00-0f-ac:12 AKM. This part was
missing from the initial implementation and a fixed length (256-bit) PMK
was used for all AKMs.
Fix this by adding more complete support for variable length PMK and use
384 bits from MSK instead of 256 bits when using this AKM. This is not
backwards compatible with the earlier implementations.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The previous implementation used an obsolete sm->eapol_key_crypt pointer
which was not set anywhere (i.e., was always NULL). In addition, the
condition of sm->eap_if->eapKeyAvailable was not valid here since this
is the case of MSK from an external authentication server and not the
internal EAP server. Consequently, the wpa_auth_pmksa_add() call here
was never used.
The PMKSA cache was still added, but it happened at the completion of
the 4-way handshake rather than at the completion of EAP authentication.
That later location looks better, so delete the unreachable code in
Access-Accept handling. In addition, remove the now complete unused
struct eapol_state_machine eapol_key_* variables.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
With driver wrappers that implement set_privacy(), set_generic_elem(),
set_ieee8021x(), or set_ap_wps_ie(), it was possible to hit a NULL
pointer dereference in error cases where interface setup failed and
the network configuration used WPA/WPA2, IEEE 802.1X, or WPS.
Fix this by skipping the driver operations in case the driver interface
is not initialized.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Don't add unnecessary P2PS follow-on PD Request attributes when
the request status is not P2P_SC_SUCCESS_DEFERRED.
Signed-off-by: Max Stepanov <Max.Stepanov@intel.com>
In P2PS PD Request processing in some error case scenarios, such as
verification of the WPS config method, the flow aborts before saving
mandatory P2PS PD Request attributes. This in turn causes the control
interface notification events to be sent with invalid parameters.
Fix this by changing the order of verification and processing steps of
the PD Request message handling.
Signed-off-by: Max Stepanov <Max.Stepanov@intel.com>
On successful P2P PD, report the chosen frequency in case the local
device is going to be the P2P GO, so in can later be used to instantiate
the new P2P GO, etc.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
In case the P2PS PD Response includes the P2P Channel List attribute,
update the peer device supported channels and verify that the local
device has common channels with the peer (only a sanity check).
If the Operating Channel attribute is included in the response, check
that it is included in the intersection and store it as the peer's
operating frequency (so it could later be used in the join flow, etc.).
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
In case the P2PS PD Request includes the P2P Channel List attribute,
update the peer device supported channels and check if we have common
channels with the peer that can be used for the connection establishment
based on the connection capabilities:
1. In case of P2PS PD Request with no common channels, defer
the flow unless auto accept equals true and the connection
capabilities equals NEW (in which case the channels would be
negotiated in the GO Negotiation).
2. In case of Follow up P2PS PD Request with no common channels,
reject the request unless the connection capability is NEW.
In addition, in case of a successful P2PS PD, save the device
operating frequency (so it can be later used for join flow, etc.).
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Add operating channel selection and channel list processing similar to
that done when building GO Negotiation Request, i.e., consider the
currently used channels, configured channels, etc.
P2PS introduces a flow where a responder needs to provide channel data
without being previously aware of the current constraints, i.e., the
channels currently in use by other interfaces. To handle this, extend
the get_group_capability() callback to also handle channel selection
aspects of group capabilities.
In case there is an active P2P GO that is going to be used for the P2PS
PD, force its current operating frequency in the PD attributes.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
If a Provision Discovery Request is received for an unknown peer, a new
device entry is being added, but the flow continues without updating the
local p2p_device pointer, requiring to check the pointer value before
every access.
1. Change this, so once a device is added, the flow updates the local
p2p_device pointer and avoids the checks later in the flow.
2. If the device is not known even after adding it, skip the processing,
send the PD Response, and return.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
It is possible that p2p_build_prov_disc_resp() is called with a NULL
device entry, which might be dereferenced when calling
p2p->cfg->get_persistent_group() for the P2PS with persistent group
case. Fix this by checking the device pointer before accessing it.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Write a text version of the content type and handshake type in debug log
to make it easier to follow TLS exchange.
Signed-off-by: Jouni Malinen <j@w1.fi>
The utf8_string_len comparison was off by one and ended up accepting a
truncated three-byte encoded UTF-8 character at the end of the string if
the octet was missing. Since the password string gets null terminated in
the configuration, this did not result in reading beyond the buffer, but
anyway, it is better to explicitly reject the string rather than try to
use an incorrectly encoded UTF-8 string as the password.
Signed-off-by: Jouni Malinen <j@w1.fi>
BoringSSL has removed the OpenSSL OCSP implementation (OCSP_*()
functions) and instead, provides only a minimal mechanism for include
the status request extension and fetching the response from the server.
As such, the previous OpenSSL-based implementation for OCSP stapling is
not usable with BoringSSL.
Add a new implementation that uses BoringSSL to request and fetch the
OCSP stapling response and then parse and validate this with the new
implementation within wpa_supplicant. While this may not have identical
behavior with the OpenSSL-based implementation, this should be a good
starting point for being able to use OCSP stapling with BoringSSL.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Validate that all the required attributes appear in a P2PS PD Request,
and in addition, in the case of follow-on PD Request, check that the
given values match those of the original PD Request.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
When a follow-on PD request is received, peer should not send a
follow-on PD response except the case when the PD request status value
is 12 (Success: accepted by user). Previously, the wpa_supplicant
implementation behaved differently sending the follow-on PD Response on
any follow-on PD Request.
Fix the issue by adding the following changes:
1. Don't send PD Response if the follow-on PD Request status is
different than 12 (seeker side).
2. Don't wait for the follow-on PD Response if the follow-on PD
Request was sent with the status different than 12 (advertiser
side).
3. If the follow-on PD Request was sent with the status different
than 12 use the follow-on PD Request ACK as PD completion event
(advertiser side).
4. Notify ASP about the PD completion by sending P2PS-PROV-DONE with
the PD Request status (advertiser side).
Signed-off-by: Max Stepanov <Max.Stepanov@intel.com>
It is expected that p2p_flush() should stop any ongoing p2p operation.
However, this was not the case with extended listen which was not
cancelled on p2p_flush() flows. Fix this, by cancelling the extended
listen in p2p_flush().
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
The new hostapd configuration parameter anqp_elem can now be used to
configure arbitrary ANQP-elements for the GAS/ANQP server. In addition
to supporting new elements, this can be used to override previously
supported elements if some special values are needed (mainly for testing
purposes).
The parameter uses following format:
anqp_elem=<InfoID>:<hexdump of payload>
For example, AP Geospatial Location ANQP-element with unknown location:
anqp_elem=265:0000
and AP Civic Location ANQP-element with unknown location:
anqp_elem=266:000000
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The switch to BoringSSL broke keystore-backed keys because
wpa_supplicant was using the dynamic ENGINE loading to load
the keystore module.
The ENGINE-like functionality in BoringSSL is much simpler
and this change should enable it.
Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
Some devices cannot respond to inactive client probe (empty data frame)
within one second. For example, iPhone may take up to 3 secs. This
becomes a significant problem when ap_max_inactivity is set to lower
value such as 10 secs. iPhone can lose Wi-Fi connection after ~1 min
of user inactivity.
Signed-off-by: Dmitry Ivanov <dima@ubnt.com>
On RADIUS auth/acct failures hostapd will try a new server if one is
available. Reuse the failover logic to force a socket renewal if only
one RADIUS server is configured.
This fixes problems when a route for the RADIUS server gets added after
the socket was "connected". The RADIUS socket is still sending the
RADIUS requests out using the previous route.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
IEEE Std 802.11-2012 13.3.1 states that the AID should be generated on
the local node for each peer. Previously, we were using the peer link ID
(generated by the peer) which may not be unique among all peers. Correct
this by reusing the AP AID generation code.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Commit d66dcb0d0b ('WEP: Remove VLAN
support from hostapd') already removed VLAN support for WEP encryption,
so vlan_setup_encryption_dyn() is no longer needed.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
This ensures that group key is set as long as the interface exists.
Additionally, ifconfig_up is needed as wpa_group will enter
FATAL_FAILURE if the interface is still down. Also vlan_remove_dynamic()
is moved after wpa_auth_sta_deinit() so vlan_remove_dynamic() can check
it was the last user of the wpa_group.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
Some APs don't include a CSA IE when an ECSA IE is generated,
and mac80211 used to fail following their channel switch. Add
a testing option to hostapd to allow reproducing the behavior.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Fix and extend the ieee80211_freq_to_channel_ext() function to deal
correctly with VHT operating classes (128, 129, 130).
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
The CSA channel and operating class values need to be set for all types
of channel switch (i.e., either if it's triggered by the control
interfaces or due to the GO-follows-STA flow). To do so, move the code
that sets them from the GO-follows-STA flow to the more generic
hostapd_fill_csa_settings() function.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
The hostapd_hw_get_channel() function can't be used to convert center
frequencies to channel numbers, because the hw mode lists don't have all
the center frequencies. The hw mode lists have the main channel
frequencies and flags to indicate the channel topography.
For instance, channel 5805 with VHT80- has the channel center frequency
segment 0 at 5775. This segment is only indicated indirectly in the hw
mode list by the HOSTAPD_CHAN_VHT_50_30 flag. The hw mode list doesn't
have any elements with frequency 5775 to allow the conversion to a
channel number. Thus, we need to use ieee80211_freq_to_chan() instead.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Pass to the driver a list of CSA counter offsets when sending Probe
Response frames during a CSA period. This allows the kernel to correctly
update the CSA/eCSA elements.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Some management frames contain CSA counters which should be updated by
kernel. Change driver op send_mlme() allowing to send a frame,
specifying an array of offsets to the CSA counters which should be
updated. For example, CSA offsets parameters should be specified when
sending Probe Response frames during CSA period.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Advertise current operating class in Beacon and Probe Response frames.
This Supported Operating Classes element is required by the standard
when extended channel switch is supported. However, since this element
doesn't reflect correctly the sub-band spectrum breakdown and can't be
effectively used by clients, publish only the minimal required part
which is the current operating class.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Fix the order of CSA, eCSA, Secondary Channel Offset, and Wide Bandwidth
Channel Switch Wrapper elements in Beacon and Probe Response frames.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Add new GO frequency move policy. The P2P_GO_FREQ_MOVE_SCM_ECSA prefers
SCM if all the clients advertise eCSA support and the candidate
frequency is one of the group common frequencies.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Extended channel switch provides an ability to switch between operating
classes and is required for P2P Devices by the P2P specification when
switching in 5 GHz.
When the operating class is provided for channel switch, the AP/P2P GO
will use eCSA IE in addition to the regular CSA IE both on 2.4 GHz and 5
GHz bands.
Transitions between different hw_modes are not supported.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Channel switch may be performed using both CSA and eCSA IEs together.
This may happen, for example with a P2P GO on band A with legacy
clients. Extend driver API to support up to 2 CSA counters.
This patch also includes the required implementation for nl80211.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
When building Beacon and Probe Response frames for the target channel,
consider bandwidth parameter for VHT channels. In addition, add support
for updating vht_oper_centr_freq_seg0_idx and
vht_oper_centr_freq_seg1_idx.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
When switching to a VHT channel with width greater than 20 MHz, add Wide
Bandwidth Channel Switch element. This element is added in Beacon and
Probe Response frames inside Channel Switch Wrapper element.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
When CSA is started, hostapd_change_config_freq() computes the channel
from the provided frequency. Use this stored channel to add CSA IE in
Beacon frames, instead of recomputing the channel each time.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
All the other web_connection_parse_*() functions were already doing
this, so make the GET handler consistent as well.
Signed-off-by: Jouni Malinen <j@w1.fi>
Commit 7d711541dc ('Clear TK part of PTK
after driver key configuration') started clearing TK from memory
immediately after having configured it to the driver when processing
EAPOL-Key message 3/4. While this covered the most common case, it did
not take into account the possibility of the authenticator having to
retry EAPOL-Key message 3/4 in case the first EAPOL-Key message 4/4
response is lost. That case ended up trying to reinstall the same TK to
the driver, but the key was not available anymore.
Fix the EAPOL-Key message 3/4 retry case by configuring TK to the driver
only once. There was no need to try to set the same key after each
EAPOL-Key message 3/4 since TK could not change. If actual PTK rekeying
is used, the new TK will be configured once when processing the new
EAPOL-Key message 3/4 for the first time.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This allows the binary sizes to be reduced if no support for nl80211
vendor extensions are needed.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Allow wpa_supplicant to use vendor scan (if supported by the driver)
together with the normal nl80211 scan and handling external scan events.
Since this results in possibility of concurrent scan operations, some of
the operations related to scan results need to check more carefully when
an event is relevant for a specific interface.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This commit contains the necessary changes for supporting the QCA vendor
scan implementation, i.e., sending the vendor scan command to underlying
driver and handling the vendor scan events from the driver.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Introduce definitions for QCA vendor specific subcommands
and attributes to support vendor scan request.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
