Allow configuration of Beacon frame TX rate from hostapd.conf with
"beacon_rate=xx" option. The following format is used to set
legacy/HT/VHT beacon rates:
Legacy (CCK/OFDM rates):
beacon_rate=<legacy rate in 100 kbps>
HT:
beacon_rate=ht:<HT MCS>
VHT:
beacon_rate=vht:<VHT MCS>
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add a configuration option in hostapd.conf and in neighbor report that
sets an AP as stationary. To enable this option on the current AP set
the config option stationary_ap to 1. To set a neighbor entry to be
marked as stationary add the word stat to the SET_NEIGHBOR command. This
option tells hostapd to send LCI data even if it is older than requested
by max age subelement in RRM request.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
This adds CONFIG_FILS=y build configuration option and new key
management options for FILS authentication.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Station should be able to connect initially without ft_pmk_cache filled,
so the target AP has the PSK available and thus the same information as
the origin AP. Therefore neither caching nor communication between the
APs with respect to PMK-R0 or PMK-R1 or VLANs is required if the target
AP derives the required PMKs locally.
This patch introduces the generation of the required PMKs locally for
FT-PSK. Additionally, PMK-R0 is not stored (and thus pushed) for FT-PSK.
So for FT-PSK networks, no configuration of inter-AP communication is
needed anymore when using ft_psk_generate_local=1 configuration. The
default behavior (ft_psk_generate_local=0) remains to use the pull/push
protocol.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
Add configuration options that control publishing of fine timing
measurement (FTM) responder and initiator functionality via bits 70, 71
of Extended Capabilities element. Typically, FTM functionality is
controlled by a location framework outside hostapd. When framework is
activated, it will use hostapd to configure the AP to publish the FTM
functionality. See IEEE P802.11-REVmc/D7.0, 9.4.2.27.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Some deployed stations incorrectly consider nsts capability in
(Re)Association Response frame as required capability instead of maximum
capability and if it is greater than station's capability then beamform
will not happen in uplink traffic.
This commit adds support for an optional workaround to use station's
nsts capability in (Re)Association Response frame if the station's nsts
is less than AP by using the use_sta_nsts=1 configuration parameter.
This configuration is introduced in this commit and it is disabled by
default.
Signed-off-by: Tamizh chelvam <c_traja@qti.qualcomm.com>
This can be used to mandate the presence of the Message-Authenticator
attribute on CoA/Disconnect-Request packets.
Signed-off-by: Nick Lowe <nick.lowe@lugatech.com>
gas_address3=1 can now be used to force hostapd to use the IEEE 802.11
standards compliant Address 3 field value (Wildcard BSSID when not
associated) even if the GAS request uses non-compliant address (AP
BSSID).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This new parameter allows hostapd to add Vendor Specific elements into
(Re)Association Response frames similarly to the way vendor_elements
parameter can be used for Beacon and Probe Response frames.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Extend the radio_measurements parameter to save all the supported
RRM capabilities as it's used in RM enabled capabilities element.
Make this parameter not directly configurable via config file (though,
keep the radio_measurements parameter for some time for backwards
compatibility). Instead, add a configuration option to enable neighbor
report via radio measurements. Other features can be added later as
well.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Add a new 'use_driver_iface_addr' configuration parameter to allow use
of the default interface address generated by the driver on interface
creation. This can be useful when specific MAC addresses were allocated
to the device and we want to use them for multi-BSS operation.
Signed-off-by: Eliad Peller <eliad@wizery.com>
nas_identifier needs to be set to a unique value for RADIUS accounting
to work properly. This needs to be unique for each BSS.
Signed-off-by: Jouni Malinen <j@w1.fi>
r1_key_holder is an identifier that was always set to zero if unless
configured before.
See 11.6.1.7.4 of IEEE Std 802.11-2012 which reads
"R1KH-ID is a MAC address of the holder of the PMK-R1 in the
Authenticator of the AP"
See 12.2.2 of IEEE Std 802.11-2012 which reads
"Each R0KH-ID and R1KH-ID is assumed to be expressed as a unique
identifier within the mobility domain."
"The R1KH-ID shall be set to a MAC address of the physical entity
that stores the PMK-R1 ..."
Defaulting this to BSSID is a more reasonable value since we have not
rejected the missing r1_key_holder as invalid configuration.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
This allows the stations to be assigned to their own vif. It does not
need dynamic_vlan to be set. Make hostapd call ap_sta_set_vlan even if
!vlan_desc.notempty, so vlan_id can be assigned regardless.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
This adds a new hostapd configuration parameter
ocsp_stapling_response_multi that can be used similarly to the existing
ocsp_stapling_response, but for the purpose of providing multiple cached
OCSP responses. This commit adds only the configuration parameter, but
does not yet add support for this mechanism with any of the supported
TLS implementations.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Expire pending DB request for EAP-SIM/AKA/AKA'. Timeout defaults to 1
second and is user configurable in hostapd.conf (eap_sim_db_timeout).
Signed-off-by: Frederic Leroy <frederic.leroy@b-com.com>
To be consistent with the internal representation of how to disable
framentation, allow -1 as a value to disable it in configuration.
Signed-off-by: Matthias May <matthias.may@neratec.com>
Since we have HT rates the maximum framesize is no longer 2346. The
usual maximum size of an A-MPDU is 65535. To disable RTS, the value -1
is already internally used. Allow it in the configuration parameter.
Signed-off-by: Matthias May <matthias.may@neratec.com>
The new hostapd configuration parameter no_probe_resp_if_max_sta=1 can
be used to request hostapd not to reply to broadcast Probe Request
frames from unassociated STA if there is no room for additional stations
(max_num_sta). This can be used to discourage a STA from trying to
associate with this AP if the association would be rejected due to
maximum STA limit.
Signed-off-by: Jouni Malinen <j@w1.fi>
The new hostapd configuration parameter anqp_elem can now be used to
configure arbitrary ANQP-elements for the GAS/ANQP server. In addition
to supporting new elements, this can be used to override previously
supported elements if some special values are needed (mainly for testing
purposes).
The parameter uses following format:
anqp_elem=<InfoID>:<hexdump of payload>
For example, AP Geospatial Location ANQP-element with unknown location:
anqp_elem=265:0000
and AP Civic Location ANQP-element with unknown location:
anqp_elem=266:000000
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Some APs don't include a CSA IE when an ECSA IE is generated,
and mac80211 used to fail following their channel switch. Add
a testing option to hostapd to allow reproducing the behavior.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The new no_auth_if_seen_on=<ifname> parameter can now be used to
configure hostapd to reject authentication from a station that was seen
on another radio.
This can be used with enabled track_sta_max_num configuration on another
interface controlled by the same hostapd process to reject
authentication attempts from a station that has been detected to be
capable of operating on another band, e.g., to try to reduce likelihood
of the station selecting a 2.4 GHz BSS when the AP operates both a 2.4
GHz and 5 GHz BSS concurrently.
Note: Enabling this can cause connectivity issues and increase latency for
connecting with the AP.
Signed-off-by: Jouni Malinen <j@w1.fi>
The new no_probe_resp_if_seen_on=<ifname> parameter can now be used to
configure hostapd to not reply to group-addressed Probe Request from a
station that was seen on another radio.
This can be used with enabled track_sta_max_num configuration on another
interface controlled by the same hostapd process to restrict Probe
Request frame handling from replying to group-addressed Probe Request
frames from a station that has been detected to be capable of operating
on another band, e.g., to try to reduce likelihood of the station
selecting a 2.4 GHz BSS when the AP operates both a 2.4 GHz and 5 GHz
BSS concurrently.
Note: Enabling this can cause connectivity issues and increase latency
for discovering the AP.
Signed-off-by: Jouni Malinen <j@w1.fi>
hostapd can now be configured to track unconnected stations based on
Probe Request frames seen from them. This can be used, e.g., to detect
dualband capable station before they have associated. Such information
could then be used to provide guidance on which colocated BSS to use in
case of a dualband AP that operates concurrently on multiple bands under
the control of a single hostapd process.
Signed-off-by: Jouni Malinen <j@w1.fi>
This new hostapd configuration parameter can be used to enable TLS
session resumption. This commit adds the configuration parameter through
the configuration system and RADIUS/EAPOL/EAP server components. The
actual changes to enable session caching will be addressed in followup
commits.
Signed-off-by: Jouni Malinen <j@w1.fi>
Depending on the number of antennas, the txbf sounding
and steering capabilites need to be extended.
Signed-off-by: Vivek Natarajan <nataraja@qti.qualcomm.com>
The cwmin/cwmax parameters were limited more than is needed. Allow the
full range (0..15 for wmm_ac_??_{cwmin,cwmax} and 1..32767 for
tx_queue_data?_{cwmin,cwmax}) to be used.
Signed-off-by: Jouni Malinen <j@w1.fi>
The standard hardcodes the MU Beamformee Capable subfield is hardcoded
to 0 when transmitting by an AP, so there is no need to provide a
configuration parameter for setting this to one.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
When device supports dual band operations with offloaded ACS, hw_mode
can now be set to any band (hw_mode=any) in order to allow ACS to select
the best channel from any band. After a channel is selected, the hw_mode
is updated for hostapd.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
OpenSSL is moving to use 2048-bit DH key size as the default with
dhparam. Increase the value in the hostapd.conf to match that to reduce
likelihood of ending up using a shorter key.
Signed-off-by: Jouni Malinen <j@w1.fi>
Handling of WPS RF band for 60 GHz was missing. Add it in all relevant
places and also map "AES" as the cipher to GCMP instead of CCMP when
operating on the 60 GHz band.
Signed-off-by: Hamad Kadmany <qca_hkadmany@qca.qualcomm.com>
This can be used with Proxy ARP to allow multicast NAs to be forwarded
to associated STAs using link layer unicast delivery. This used to be
hardcoded to be enabled, but it is now disabled by default and can be
enabled with na_mcast_to_ucast=1. This functionality may not be desired
in all networks and most cases work without it, so the new
default-to-disabled is more appropriate.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Update ACS driver offload feature for VHT configuration. In addition,
this allows the chanlist parameter to be used to specify which channels
are included as options for the offloaded ACS case.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The new hostapd.conf parameter radius_client_addr can now be used to
select a specific local IP address to be used as the RADIUS client
address.
Signed-off-by: Jouni Malinen <j@w1.fi>
The new acs_chan_bias configuration parameter is a space-separated list
of <channel>:<bias> pairs. It can be used to increase (or decrease) the
likelihood of a specific channel to be selected by the ACS algorithm.
The total interference factor for each channel gets multiplied by the
specified bias value before finding the channel with the lowest value.
In other words, values between 0.0 and 1.0 can be used to make a channel
more likely to be picked while values larger than 1.0 make the specified
channel less likely to be picked. This can be used, e.g., to prefer the
commonly used 2.4 GHz band channels 1, 6, and 11 (which is the default
behavior on 2.4 GHz band if no acs_chan_bias parameter is specified).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This parameter has been available for more than just testing purposes,
i.e., OBSS scanning has already been used to enable 20-to-40 MHz channel
changes on 2.4 GHz.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add the possibility to define a subset of channels used by the ACS
engine when not operating on DFS channels.
Signed-off-by: Adrien Decostre <ad.decostre@gmail.com>
Derive rRK and rIK on EAP server if ERP is enabled and use these keys to
allow EAP re-authentication to be used and to derive rMSK.
The new hostapd configuration parameter eap_server_erp=1 can now be used
to configure the integrated EAP server to derive EMSK, rRK, and rIK at
the successful completion of an EAP authentication method. This
functionality is not included in the default build and can be enabled
with CONFIG_ERP=y.
Signed-off-by: Jouni Malinen <j@w1.fi>
hostapd can now be configured to transmit EAP-Initiate/Re-auth-Start
before EAP-Request/Identity to try to initiate ERP. This is disabled by
default and can be enabled with erp_send_reauth_start=1 and optional
erp_reauth_start_domain=<domain>.
Signed-off-by: Jouni Malinen <j@w1.fi>
hostapd was still providing couple of parameters that were used only in
the already removed driver_test.c framework.
Signed-off-by: Jouni Malinen <j@w1.fi>
Number of documentation and configuration files had references to the
madwifi driver interface that was removed in the previous commit. Remove
these references as well.
Signed-off-by: Jouni Malinen <j@w1.fi>
Proxy ARP allows the AP devices to keep track of the hardware address to
IP address mapping of the STA devices within the BSS. When a request for
such information is made (i.e., ARP request, Neighbor Solicitation), the
AP will respond on behalf of the STA device within the BSS. Such
requests could originate from a device within the BSS or also from the
bridge. In the process of the AP replying to the request (i.e., ARP
reply, Neighbor Advertisement), the AP will drop the original request
frame. The relevant STA will not even know that such information was
ever requested.
This feature is a requirement for Hotspot 2.0, and is defined in IEEE
Std 802.11-2012, 10.23.13. While the Proxy ARP support code mainly
resides in the kernel bridge code, in order to optimize the performance
and simplify kernel implementation, the DHCP snooping code was added to
the hostapd.
Signed-off-by: Kyeyoon Park <kyeyoonp@qca.qualcomm.com>
The new "bss_load_update_period" parameter can be used to configure
hostapd to advertise its BSS Load element in Beacon and Probe Response
frames. This parameter is in the units of BUs (Beacon Units).
When enabled, the STA Count and the Channel Utilization value will be
updated periodically in the BSS Load element. The AAC is set to 0 sinze
explicit admission control is not supported. Channel Utilization is
calculated based on the channel survey information from the driver and
as such, requires a driver that supports providing that information for
the current operating channel.
Signed-off-by: Kyeyoon Park <kyeyoonp@qca.qualcomm.com>
