This implements support for the new NL80211_ATTR_SPLIT_WIPHY_DUMP in
nl80211 to handle wiphy information that cannot fit in one message.
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-hostap: Dennis H Jensen <dennis.h.jensen@siemens.com>
The peer commit element needs to be validated to pass one of the steps
listed in IEEE 802.11, 11.3.5.4:
scalar-op(r, ELEMENT) = 1 modulo p
Similar step was present for ECC groups, but was missing for FFC groups.
This is needed to avoid dictionary attacks.
Thanks to Michael Roßberg and Sascha Grau for reporting this.
Signed-hostap: Jouni Malinen <j@w1.fi>
It is clearer to keep all the validation steps described in IEEE 802.11
11.3.5.4 in a single location instead of splitting this between the
parsing and processing functions.
Signed-hostap: Jouni Malinen <j@w1.fi>
Command line parameter to run-p2p-tests.py can now be used to select
which test case is run instead of always running all test cases.
Signed-hostap: Jouni Malinen <j@w1.fi>
run-p2p-tests.py can now be used to run all P2P test cases. The
actual test cases are defined in test_p2p_*.py files.
Signed-hostap: Jouni Malinen <j@w1.fi>
This will hopefully grow over time to become a much more complete
testing mechanism that uses mac80211_hwsim to verify various
wpa_supplicant and hostapd functions automatically.
Signed-hostap: Jouni Malinen <j@w1.fi>
When p2p_invite persistent=<id> is used to request a persistent group to
be re-invoked, the peer may reply with status=1 (info not yet available)
if upper layer processing of the invitiation is requested. The peer is
ten expected to start another invitation exchanged within 120 seconds if
the user authorizes the connection. Allow this process to be used more
easily by automatically authorizing the peer that we tried to invite to
use this second invitation sequence even if persistent_reconnect=0.
For this mechanism to work, the device that starts the invitation needs
to start listen mode to be able to receive the invitation request from
the peer. At least for now, this is not done automatically, but future
changes could potentially enable this automatically at least if there
are no concurrent operations in progress.
Example sequence on the initiator:
cmd: P2P_INVITE persistent=1 peer=<addr>
event: P2P-INVITATION-RESULT status=1
cmd: P2P_LISTEN 120
wait for peer to start another invitiation round.. group will be
re-invoked automatically
On the peer (with persistent_reconnect=0):
event: P2P-INVITATION-RECEIVED sa=<addr> persistent=1 [freq=<MHz>]
wait for user approval
cmd: P2P_INVITE persistent=1 peer=<addr>
group will be re-invoked automatically
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
When a device that is a GO in a persistent group receives an Invitation
Request from a P2P client and persistent_reconnect=0, upper layer is
notified of this with P2P-INVITATION-RECEIVED event. The upper layer is
supposed to run another invitation exchange is this case, but if that
does not happen and the GO is started without successful (status=0)
invitation exchange, the operating channel for the group may end up
getting set in a way that the P2P client is not able to support. Provide
optional freq parameter in the P2P-INVITATION-RECEIVED event on the GO
side. If this parameter is received and the upper layer decides to issue
P2P_GROUP_ADD command, that command should include this freq parameter
to make sure the operating channel gets selected from the set that the
peer can support.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
beacon_int (in TU) can now be used to configure Beacon interval for AP
mode operations (including P2P GO) in wpa_supplicant. This can be set
either in a network block or as a global parameter in the configuration
file (or with "SET beacon_int <value>" control interface command) to
apply for all networks that do not include the beacon_int parameter to
override the default.
In addition, this commits extends the dtim_period parameter to be
available as a global parameter to set the default value. dtim_period is
now stored in the configuration file, too, if it was set.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Peer device includes its list of allowed operating channels in the
Invitation Response frame. When we are becoming the GO, use that list
from the peer to filter out acceptable channels to avoid selecting a
channel that the peer is unable to use.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
When re-invoking a persistent group in P2P client role, the new
pref=<MHz> parameter can now be used with the p2p_invite command to
indicate a preferred operating frequency. Unlike the older freq=<MHz>
parameter, this leaves GO an option to select another channel (from our
supported channels) if the GO cannot accept the channel.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
p2p_connect() and p2p_invite() cases used more or less identical
implementatin. Use a shared function to avoid duplicated code.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
If multi channel concurrency is supported, we have to populate the
p2p_channels with list of channels that we support. Use the same design
that was previously added for GO Negotiation.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The VHT IE struct just has an opaque 8-byte array for the MCS
set, make it more expressive by explicitly naming the pieces.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
Commit fb8984fd6f cleared wps_method to
WPS_NOT_READY in p2p_stop_find_for_freq() as an attempt to clear
authorization when a group formation is cancelled. However, this code
path is hit also in cases where the user did not actually cancel
anything (e.g., from p2p_process_go_neg_req()). As such, it is not fine
to clear wps_method here even if it could be proper for some cases. For
now, revert that part to avoid regressions and consider clearing
wps_method on cancel separately.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
In case we have replied to a peer's GO Negotiation Request frame with a
GO Negotiation Response frame using status code
info-currently-unavailable (1), the peer is likely going to wait for us
to initiate GO Negotiation on its Listen channel. We were previously
using alternativing send-GO-Neg-Req and Listen phase when providing that
response after the user had authorized the connection. However, the
Listen phase here is unnecessary in this case and will make the
connection take longer time to go through. Skip the Listen phase and
make the wait-for-GO-Neg-Resp timeout random between 100 and 200 ms to
avoid getting in sync with the peer. In practice, this will make us
retry GO Negotiation Request frames more frequently and remain on the
peer's Listen channel for most of the time when initiating GO
Negotiation after status=1 response.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
There may be environments in which large number of devices are operating
on the social channels. In such cases, it is possible for the Action
frame TX operation wait for quite long time before being able to get the
frame out. To avoid triggering GO Negotiation failures, increase the
timeouts for GO Neg Req (with TX ACK) and GO Neg Resp (with or without
TX ACK as long as status=0) to 500 ms.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Most of the print_bss_info() cases were already returning zero lenth to
avoid returning partial returns to the BSS commands, but the HS 2.0 and
Wi-Fi Display entries behaved differently. Make those consistent with
rest of the items.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This allows ctrl_iface users to iterate through the BSS entries by
fetching multiple BSS entries with "BSS RANGE=N-" without having to use
one extra round to get empty return value as the indication of the last
entry having been found.
Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
This flag will add ==== delimiter between to separate bss results.
Unlike the other BSS command MASK values, this delimiter is not
included by default to avoid issues with existing users of the BSS
command.
Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
This patch uses existing scan results for fast connection on REASSOCIATE
and RECONNECT commands.
Signed-hostap: Masashi Honma <masashi.honma@gmail.com>
wpa_supplicant uses 4096 byte buffer for control interface responses, so
wpa_cli should do the same to avoid truncating responses unnecessarily.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
It is possible for the driver to indicate multiple Probe Request frames
that would be processed in a single loop. If those frames happen to be
from a peer which with we are trying to start GO Negotiation, multiple
timeouts to start GO Negotiation (p2p_go_neg_start) could end up being
scheduled. This would result in confusing burst of multiple GO
Negotiation Request frames being sent once the RX loop finally
concludes. Avoid this by scheduling only a single eloop timeout to
trigger GO Negotiation regardless of how many Probe Request frames from
the peer is received. In addition, make sure this timeout gets canceled
in p2p_deinit().
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
If we have already sent out GO Negotiation Response and are waiting for
the peer to reply with GO Negotiation Confirm, there is no point in
re-starting GO Negotiation based on Probe Request frame from the peer.
Doing that would just result in confusing GO Negotiation exchange with
multiple sessions running at the same time.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The device that is selected as the GO shall incode P2P Group ID
attribute in GO Negotiation Response/Confirm message. Previously we did
not reject a message without that attribute since it was possible to
continue operations even without knowing the SSID. However, this can
potentially result in confusing results since missing P2P Group ID
attribute can be a sign of conflicting GO role determination (both
devices assuming the peer is the GO). To get clearer end result for the
GO Negotiation, reject this as a fatal error. In addition, stop GO
Negotiation if GO Negotiation Confirm indicates non-zero status since
that is also a fatal error.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Commit 624b4d5a64 changed GO Negotiation
to use the same Dialog Token value for all retransmissions of the GO
Negotiation Request within the same session. However, it did leave the
tie breaker bit changing for each frame. While this should not have
caused issues for most cases, it looks like there are possible sequences
where the peer may end up replying to two GO Negotiation Request frames
with different tie breaker values. If in such a case the different GO
Negotiation Response frames are used at each device, GO role
determination may result in conflicting results when same GO intent is
used.
Fix this by assigning the tie breaker value at the same time with the
dialog token (i.e., when processing the p2p_connect command instead of
for each transmitted GO Negotiation Request frame) to avoid issues with
GO selection.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The information of the peer's VHT capability is required for the
driver to establish a TDLS link in VHT mode with a compatible peer.
Pass this information to the driver when the peer station is
getting added.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
