Remove the separate driver_ops functions set_cts_protect(),
set_preamble(), set_short_slot_time(), and set_ht_params(). These
belong into same set of operations as set_ap(), so there is no need
to maintain separate functions that just make the driver wrapper
more complex.
Since these have only been used with driver_nl80211.c, the driver_ops
can be removed immediately instead of maintaining backwards
compatibility period with the old functions.
The AP client isolation parameter is now available through set_ap().
driver_nl80211.c was the only driver wrapper using the set_intra_bss()
call in hostap.git, but some external trees may have used this. Once
those are cleared, the set_infra_bss() driver_ops can be removed
completely. The only remaining use case for it currently is in P2P
GO mode with wpa_supplicant.
"hostapd_cli ess_disassoc (STA addr) (URL)" can now be used to send
an ESS Dissassociation Imminent notification to the STA. This event
is shown in wpa_supplicant ctrl_iface monitors (e.g., wpa_cli):
"WNM: ESS Disassociation Imminent - session_info_url=http://example.com/session/"
Use the SSID filter list passed in the scheduled scan request down to
the kernel driver, so it can use the list to return only the wanted
SSIDs. Some kernel drivers can use this information to offload the
SSID filter to the hardware, helping with reducing the power
consumption.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Currently the P2P Interface name[p2p-%s-%d] is reset when the P2P
Interface name reaches the "IFNAMSIZ" limit. Monitor interface name is
derived from p2p interface name with the addition of few characters
[mon.p2p-%s-%d] and hence Monitor interface name hits IFNAMSIZ limit
before P2P Interface name. Rename the monitor interface name to
mon-%s-%d to reduce the length to same with p2p-%s-%d.
This new flag can be used to change wpa_supplicant behavior in the
default ap_scan=1 mode to move BSS selection into the driver (likely
firmware). This commit is only adding the flag; separate commits
will be used to change the actual connection/roaming behavior.
This adds support for RSN pre-authentication with nl80211 interface and
drivers that handle roaming internally (i.e., wpa_supplicant is not
responsible for requesting scan results that provide the needed
information without these events).
cfg80211 does not currently allow NL80211_CMD_CONNECT when there
is already an association. This can result in wpa_supplicant being
unable to request a connection if the interface is already in
connected state. Work around this by requesting disconnection if
the connect command fails with EALREADY error. This allows
wpa_supplicant to recover from the unexpected state and complete
the connect request on next attempt.
Currently, the following can happen:
1) P2P state machine requests R-O-C
2) user changes their mind and aborts
3) P2P state machine aborts R-O-C
4) driver_nl80211 rejects abort since there
was no notification about the start yet
5) R-O-C period start notification from kernel
6) P2P state machine requests new R-O-C
7) this overlaps with old R-O-C -- iwlwifi driver
can't handle that and returns -EBUSY
8) state machine stops dead in its tracks
The reason is that the abort isn't going through properly. Instead of
tracking whether a R-O-C is active in driver_nl80211, track whether one
was requested to avoid this scenario.
Reported-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This allows drivers to disable CCK rates from Probe Request frames.
For nl80211, this is currently applying only to the supported rates
element(s), but this mechanism could be extended to address TX rate
control masking, too, to lessen need for global rate disabling.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Since the kernel can now advertise P2P concurrent support by advertising
interface combinations, we can take advantage of that and automatically
use P2P_CONCURRENT / P2P_MGMT_AND_NON_P2P for drivers that advertise
support.
Keep driver_param=use_p2p_group_interface=1 for anyone not advertising
interface combinations in their drivers yet.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The previous code was trying to figure out which WPA version is
used based on the extra IEs requested for Association Request. That
did not work properly in cases where non-WPA networks are used with
some extra IEs. Fix this by using more robust mechanism for passing
the WPA versions from core wpa_supplicant to the driver_ops
associate().
This allows non-mac80211 drivers to report received Probe Request
frames to user space and Probe Response and Action frames to be sent
from user space when using AP/P2P GO mode.
This allows the driver to use PS buffering of Deauthentication and
Disassociation frames when the STA is in power save sleep. The STA
entry (and PTK) will be removed from the kernel only after the
Deauth/Disassoc has been transmitted (e.g., when the STA wakes up).
A hardcoded two second timeout is used to limit the length of this
window should the driver fail to deliver the frame (e.g., the STA
is out of range and does not wake up). The kernel STA entry is
marked unauthorized during the wait to avoid accepting Data
frames from the STA that we have decided to disconnect.
This behavior is available only with drivers that provide TX status
events for Deauth/Disassoc frames (nl80211 at this point). Other
drivers continue to use the previous behavior where the STA entry
is removed immediately.
This change is a first step in better supporting different driver
architectures for AP mode operations with nl80211. This commit in
itself does not add new functionality, but it makes it easier to add
new AP mode parameters to address needs of drivers that have more of
the MLME/SME in firmware or kernel.
Such using params->wpa_ie to figure out whether the connection is for
WPA/WPA2 is not correct since that buffer is used also to add WPS IE. In
case of WPS, do not add NL80211_ATTR_WPA_VERSIONS to avoid confusing
drivers.
Currently, wpa_driver_nl80211_authenticate() changes the interface type
to station. However, in case of P2P, we need to change the interface
type to P2P_CLI.
Add p2p field to the authentication params, and consider it for choosing
the correct interface type.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Commit 9f51b11395 added support for P2P
interfaces when adding a new interface. However, it didn't handle the
case in which the same interface is being used and its type is being
changed. Add support for this case.
Consequently, when doing "ap_scan_as_station" we now need to save the
actual AP interface type (AP/P2P GO) in order to restore it properly.
For that, change ap_scan_as_station type from int to nl80211_iftype, and
set it to NL80211_IFTYPE_UNSPECIFED when not used.
Signed-off-by: Eliad Peller <eliad@wizery.com>
When driver_nl80211.c has to set the netdev down to change iftype, an
RTM_NEWLINK event is generated. Do not generate
EVENT_INTERFACE_DISABLED event based on that.
When a new interface is created and already has a separate MAC address
assigned by the kernel, then we need to use that address, not just when
we've created a locally administered address.
This fixes use_p2p_group_interface=1 for iwlagn as it already makes
mac80211 assign an address for a second interface since the hardware has
two addresses assigned.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add support to wpa_supplicant for device-based GTK rekeying. In order to
support that, pass the KEK, KCK, and replay counter to the driver, and
handle rekey events that update the latter.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Send STA flags to kernel when adding a new station. This ensures
stations are added with up to date flags by kernel drivers.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Implement PMKSA cache operations add, remove, and flush using nl80211
commands NL80211_CMD_{SET,DEL,FLUSH}_PMKSA to support PMKSA caching
with drivers that select the AP and generate the RSN IE internally.
Some of these are required for proper functionality (like
get_seqnum); others may not be needed yet, but including them
allows some extra ifdef/endif blocks to be removed.
.set_rate_sets is not defined for non-hostapd, which prevents
configuring basic_rates when working as P2P GO.
Signed-off-by: Eliad Peller <eliad@wizery.com>
cfg80211 maintains separate BSS table entries for APs if the same
BSSID,SSID pair is seen on multiple channels. wpa_supplicant does
not use frequency as a separate key in the BSS table, so filter out
duplicated entries. Prefer associated BSS entry in such a case in
order to get the correct frequency into the BSS table.
When the SME is in the driver or cfg80211, the automatic selection
of auth_alg is done by leaving out the NL80211_ATTR_AUTH_TYPE
attribute from the NL80211_CMD_CONNECT command.
This should fix EAPOL reauthentication and rekeying timeout issues
with Intel clients when using WMM (e.g., with IEEE 802.11n). These
stations do not seem to be able to handle EAPOL data frames as
non-QoS Data frames after the initial setup.
This adds STA flags to hapd_send_eapol() driver op to allow
driver_nl80211.c to mark the EAPOL frames as QoS Data frame
when injecting it through the monitor interface.
This provides a means for the supplicant to directly request signal
quality metrics from the driver. This is useful, for example for
background scan algorithms that might ask desire this information
out-of-band with CQM events.
Signed-off-by: Paul Stewart <pstew@google.com>
