Commit ae8535b6e1 added a new function
wpa_sm_pmf_enabled() which is called from WNM code without ifdefs.
Define a dummy wrapper for this function to fix build if WPA2 is
disabled.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Commit 4033935dd9 updated
pmksa_cache_flush() function arguments, but forgot to update the wrapper
function for cases where WPA2 or EAP has been disabled in the build.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The Michael MIC TX and RX keys needs to be swapped in the FT case just
like in all other TKIP key configuration cases. This fixes issues where
TKIP as group cipher resulted in Michael MIC failures being detected for
each received group-addressed frame after FT protocol use.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Define a proper event prefix and include additional information to allow
ESS Dissassociation Imminent event to be used in a wpa_cli action
script.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Commit c3fea27274 added a call to clear
all other PMKSA cache entries for the same network if the PMKSA cache
entry of the current AP changed. This was needed to fix OKC cases since
the other APs would likely use the new PMK in the future. However, this
ended up clearing entries in cases where that is not desired and this
resulted in needing additional full EAP authentication with networks
that did not support OKC if wpa_supplicant was configured to try to use
it.
Make PMKSA cache entry flushing more limited so that the other entries
are removed only if they used the old PMK that was replaced for the
current AP and only if that PMK had previously been used successfully
(i.e., opportunistic flag was already cleared back to 0 in
wpa_supplicant_key_neg_complete()). This is still enough to fix the
issue described in that older commit while not causing problems for
standard PMKSA caching operations even if OKC is enabled in
wpa_supplicant configuration.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
TDLS responder STA used to retransmit the TDLS Setup Response after 5
seconds if the TDLS Setup Confirm is not received. The initiator would
have enabled the TDLS link and started transmitting the data to the peer
on the TDLS link after transmitting the TDLS Setup Confirm frame. If the
TDLS Setup Confirm frame is not received by the receiver, the
transmissions from the initiator on the direct link would get failed for
the TDLS link not getting enabled on the receiver. This commit reduces
the data delivery failure duration by shortening the retry time of the
TDLS Setup Response frames. The retry limit of the TDLS Response frame
also is increased to ensure that the peer does not miss the frames in
the reduced time period.
Signed-hostap: Sunil Dutt <duttus@codeaurora.org>
The reason code for the teardown request is overwritten for open
mode. This commit removes the code that does so by reverting parts
of commit 0cb12963b6.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The information of the peer's AID is required for the driver to
construct partial AID in VHT PPDU's. Pass this information to the driver
during add/set station operations (well, as soon as the information is
available, i.e., with set station operation currently).
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Reset ft_completed if STA receives deauthentication
between FT reassoc success and the subsequent initial
mobility authentication and association.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
A kernel commit ("mac80211: fix FT roaming") started validating that the
STA entry is marked associated when adding a key. While this is needed
to fix some FT use cases with hardware crypto, it has a side effect of
breaking TDLS key configuration. Work around this by trying to
re-configure the key for the direct link after the STA entry has been
set with all information. In addition, try to tear down the link if
anything goes wrong in key configuration (if both attempts fail) or
enabling the link in the driver.
Signed-hostap: Jouni Malinen <j@w1.fi>
Enhance TDLS Setup Request processing to support both external and
internal TDLS setup for the case where concurrent TDLS initialization
results in the TDLS Setup Request from the peer getting accepted.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
wpa_tdls_peer_free() ended up getting called after some of the
parameters from the TDLS Setup Request frame were copied into the struct
wpa_tdls_peer information. This could result in continuing with cleared
information in case the new exchange was the one that is used in
concurrent initialization case or if this is to re-negotiated an
existing TDLS link. The driver would not be provided with all the peer
capabilities correctly in such case.
Fix this by moving the existing_peer check to happen before the
information from the TDLS Setup Request frame is copied.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
If we accept the peer TPK M1 after having sent our TPK M1, we need to
reject TPK M2 from the peer to avoid going through two TDLS setup
exchanges.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
If the previously started setup is terminated in case both peers
initiate TDLS link at more or less the same time, disable the old link
to allow the dummy station entry to be deleted from cfg80211 so that a
new entry can be added for the setup direction that will be allowed to
proceed.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Add NL80211_CMD_UPDATE_FT_IES to support update of FT IEs to the
WLAN driver. Add NL80211_CMD_FT_EVENT to send FT event from the
WLAN driver. This will carry the target AP's MAC address along
with the relevant Information Elements. This event is used to
report received FT IEs (MDIE, FTIE, RSN IE, TIE, RICIE).
Signed-off-by: Deepthi Gowri <deepthi@codeaurora.org>
The information of the peer's VHT capability is required for the
driver to establish a TDLS link in VHT mode with a compatible peer.
Pass this information to the driver when the peer station is
getting added.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The contents of the peer's capability and extended capability
information is required for the driver to perform TDLS P-UAPSD and Off
Channel operations. Pass this information to the driver when the peer
station is getting added.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The information of the peer's HT capability and the QOS information is
required for the driver to perform TDLS operations. Pass this
information to the driver when the peer station is getting added.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
A TDLS Teardown frame with Reason Code 3 (Deauthenticated because
sending STA is leaving (or has left) IBSS or ESS) shall be transmitted
to all TDLS peer STAs (via the AP or via the direct path) prior to
transmitting a Disassociation frame or a Deauthentication frame to the
AP.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The reason code used for calculating the MIC should correspond to the
reason code with which the teardown frame is sent, as the receiver shall
use the one obtained in the frame for validating the MIC.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
If an implicit TDLS set up request is obtained on an existing link or an
to be established link, the previous link was not removed. This commit
disables the existing link on a new set up request. Also,
wpa_tdls_reneg() function was invoking wpa_tdls_start() on an already
existing peer for the case of internal setup, which is incorrect. Thus
the invocation of wpa_tdls_start() is removed in wpa_tdls_reneg() and
also this function is renamed to wps_tdls_remove() as it does not
renegotiation rather shall remove the link (if any) for the case of
external setup.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
There is no need to have this check copied to each caller since this
needs to be done for every case when a new peer is being added.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Peer entries were getting added on every discover request from the peer,
thus resulting in multiple entries with the same MAC address. Ensures
that a check is done for the presence of the peer entry and reuse the
existing entry instead of adding a new one.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Commit 6aaac006af modified the
pmksa_cache_init() prototype, but forgot to update the empty wrapper
function which is used when PMKSA caching is not included in the build.
Signed-hostap: Jouni Malinen <j@w1.fi>
Replace CONFIG_IEEE80211V with CONFIG_WNM to get more consistent build
options for WNM-Sleep Mode operations. Previously it was possible to
define CONFIG_IEEE80211V without CONFIG_WNM which would break the build.
In addition, IEEE 802.11v has been merged into IEEE Std 802.11-2012 and
WNM is a better term to use for this new functionality anyway.
Signed-hostap: Jouni Malinen <j@w1.fi>
These fields do not use AES keywrap. Instead, they are protected with
management frame protection (and not included if PMF is disabled).
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Expiry can always trigger a deauthentication, but otherwise,
deauthentication should only happen when the *current* cache entry is
removed and not being replaced. It should not happen when the current
PMK just happens to match the PMK of the entry being removed, since
multiple entries can have the same PMK when OKC is used and these
entries are often removed at different times.
This fixes an issue where eviction of the oldest inactive entry due to
adding a newer entry to a full cache caused a deauthentication when the
entry being removed had the same PMK as the current entry.
Signed-hostap: Dan Williams <dcbw@redhat.com>
Add pmf=1/2 to wpa_supplicant STATUS command output to indicate that PMF
was negotiated for the connect (1 = optional in this BSS, 2 = required
in this BSS).
Signed-hostap: Jouni Malinen <j@w1.fi>
This function is now unused after the last couple of commits that
removed the last uses, so remove this to keep code simpler since all
places that disassociate, can use deauthentication instead.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Even though the standard currently describes disassociation to be used
for RSN element mismatch between Beacon/Probe Response frames and
EAPOL-Key msg 3/4, this is unnecessary difference from other cases that
deauthenticate. In addition, there is no point in leaving the 802.11
Authentication in place in this case. To keep things simpler, use
deauthentication here to get rid of the only use of
wpa_sm_disassociate().
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
These values are used with WAPI and CCX and reserving the definitions
here reduces the number of merge conflicts with repositories that
include these functions.
Signed-hostap: Jouni Malinen <j@w1.fi>
This introduces new AKM for SAE and FT-SAE and adds the initial parts
for going through the SAE Authentication frame exchange. The actual SAE
algorithm and new fields in Authentication frames are not yet included
in this commit and will be added separately. This version is able to
complete a dummy authentication with the correct authentication
algorithm and transaction values to allow cfg80211/mac80211 drivers to
be tested (all the missing parts can be handled with
hostapd/wpa_supplicant changes).
Signed-hostap: Jouni Malinen <j@w1.fi>
Try to share most of the cipher information like key and RSC lengths and
suite selector conversions, etc. in wpa_common.c to avoid having similar
code throughout the WPA implementation for handling cipher specific
behavior.
Signed-hostap: Jouni Malinen <j@w1.fi>
This allows both hostapd and wpa_supplicant to be used to derive and
configure keys for GCMP. This is quite similar to CCMP key
configuration, but a different cipher suite and somewhat different rules
are used in cipher selection. It should be noted that GCMP is not
included in default parameters at least for now, so explicit
pairwise/group configuration is needed to enable it. This may change in
the future to allow GCMP to be selected automatically in cases where
CCMP could have been used.
This commit does not included changes to WPS or P2P to allow GCMP to be
used.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
cur_pmksa was left to NULL during the initial association. This can
result in unexpected behavior, e.g., in expiring PMKSA cache entries
since the current entry is not locked in that case. Fix this by updated
cur_pmksa when adding the initial PMKSA entry during msg 1/4 processing.
Signed-hostap: Jouni Malinen <j@w1.fi>
intended-for: hostap-1
If the PMKSA cache is full (i.e., 32 candidates have been seen in scan
results and have not yet expired) then any additional entries can
potentially evict the current/active entry (if it is the oldest entry),
which triggers a pointless local deauthentication. The supplicant
shouldn't replace the current/active entry if it is still valid, but
instead the oldest entry that is *not* the current/active one.
Signed-hostap: Dan Williams <dcbw@redhat.com>
intended-for: hostap-1
Remove the GPL notification text from files that were initially
contributed by Atheros Communications or Qualcomm Atheros.
Signed-hostap: Jouni Malinen <j@w1.fi>
In case of !defined(IEEE8021X_EAPOL) the definition of the stub
pmksa_cache_get() in rsn_supp/pmksa_cache.h is not correct. This patch
adds the missing argument to the function definition to fix a
regression from commit 96efeeb66b.
Signed-hostap: Antonio Quartulli <ordex@autistici.org>
When looking for PMKSA cache entries to use with a new association, only
accept entries created with the same network block that was used to
create the cache entry.
Signed-hostap: Jouni Malinen <j@w1.fi>
This makes it clearer that the PMKSA caching entry gets removed from
the driver regardless of how the internal entry from wpa_supplicant
gets cleared. In practice, this call was skipped only for the case
when the entry for the current AP was being updated, so the previous
version was likely to work with all drivers. Anyway, it is cleaner
to explicitly remove the old entry even in that case before the new
entry gets added.
Signed-hostap: Jouni Malinen <j@w1.fi>
TPK will be needed to be able to generate FTIE MIC for the
teardown message, so maintain peer data for a bit longer in
case the teardown FTIE request comes back from the driver.
