Commit 0d30cc240f forced
wpa_s->current_ssid to be cleared in wpa_supplicant_mark_disassoc()
which gets called from wpa_supplicant_event_disassoc(). This broke SME
disassoc-while-authenticating workaround for cfg80211. Fix this by
restoring wpa_s->current_ssid in case SME authentication is in progress.
Signed-hostap: Jouni Malinen <j@w1.fi>
Commit 0d30cc240f forced
wpa_s->current_ssid and wpa_s->key_mgmt to be cleared in
wpa_supplicant_mark_disassoc() which gets called from
wpa_supplicant_event_disassoc(). This broke IEEE 802.1X authentication
failure processing and P2P deauthentication notification (group
termination).
Fix this by splitting wpa_supplicant_event_disassoc() into two parts and
make wpas_p2p_deauth_notif() indicate whether the interface was removed.
If so, the last part of disassocition event processing is skipped. Since
the wpa_supplicant_mark_disassoc() call is in the second part, the above
mentioned issues are resolved. In addition, this cleans up the P2P group
interface removal case by not trying to use fast reconnection mechanism
just before the interface gets removed.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The variables used within the #ifndef block here needs to be defined in
the beginning of the function to avoid issues with some compilers.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
auto_interworking=1 configuration parameter can be used to request
wpa_supplicant to use Interworking network selection automatically as a
part of the normal (non-Interworking) network selection if the scan
results do not match with enabled networks. This makes scanning work
similarly to the "interworking_select auto" command.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Maintain state of WPS APs during iteration to find the correct AP for
WPS PIN operation when no specific BSSID is specified. This information
can be used for optimizing the order in which the APs are tried. This
commit is only adding the collection of the information and more
detailed debug information to make debug logs more helpful in figuring
out how the AP selection order could be improved.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This makes wpa_supplicant state somewhat cleaner since the information
from previously used connection is not maintained after getting
disconnected.
Signed-hostap: Jouni Malinen <j@w1.fi>
If 4-way handshake fails due to likely PSK failure or if EAP
authentication fails, disable the network block temporarily. Use longer
duration if multiple consecutive failures are seen.
Signed-hostap: Jouni Malinen <j@w1.fi>
Previously, all station mode scan operations were either skipped or
delayed while any P2P operation was in progress. To make concurrent
operations easier to use, reduce this limitation by allowing a scan
operation to be completed in the middle of a p2p_find. In addition,
allow station mode association to be completed. When the station mode
operation is run to its completion (scan results not acted on,
connection to an AP completed, connection failed), resume the p2p_find
operation.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
If key_mgmt was set to allow both WPA and non-WPA IEEE 802.1X (i.e., to
IEEE8021X WPA-EAP), non-WPA IEEE 802.1X was rejected while preparing
association parameters. Allow this special case to be handled by
selecting non-WPA case if the scan results for the AP do not include
either WPA or RSN elements.
Signed-hostap: Jouni Malinen <j@w1.fi>
The os_memcmp of bssid and wpa_s->bssid cannot return 0 in this
code path since identical os_memcmp was already done above.
Signed-hostap: Jouni Malinen <j@w1.fi>
This is the normal flow for association:
wpa_supplicant <--(EVENT_ASSOC event )-- device driver
wpa_supplicant --( get_bssid() )--> device driver
wpa_supplicant <--( return BSSID )-- device driver
However, a device driver could return EINVAL for get_bssid() because it
recognizes it has already been disconnected. When the wpa_supplicant
received EINVAL, the bssid field could be used uninitialized in the
following flow:
wpa_supplicant <--(EVENT_ASSOC event )-- device driver
device driver (receive deauth)
wpa_supplicant --( get_bssid() )--> device driver
wpa_supplicant <--( return EINVAL )-- device driver
Prevent this by requiring the get_bssid() call to succeed when
processing association events.
When a special scan_res_handler is used the scan parameters may not have
been suitable for other purposes (e.g., during a p2p_find operation). As
such, do not indicate such scan results to other virtual interfaces
using the same radio.
Signed-hostap: Jouni Malinen <j@w1.fi>
In the properties changed signal, added a new property
"DisconnectReason", which carries the IEEE 802.11 reason code of the
most recent disassociation or deauthentication event. The reason code is
negative if it is locally generated. The property is sent to the DBUS
immediately so as to prevent it from being coalesced with other
disconnect events.
Signed-off-by: Gary Morain <gmorain@chromium.org>
Like bgscan, autoscan is an optional module based feature to automate
scanning but while disconnected or inactive.
Instead of requesting directly a scan, it only sets the scan_interval
and the sched_scan_interval. So, if the driver supports sched_scan,
autoscan will be able to tweak its interval. Otherwise, the tweaked
scan_interval will be used. If scan parameters needs to be tweaked, an
autoscan_params pointer in wpa_s will provide those. So req_scan /
req_sched_scan will not set the scan parameters as they usually do, but
instead will use this pointer.
Modules will not have to request a scan directly, like bgscan does.
Instead, it will need to return the interval it wants after each
notification.
Signed-hostap: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Some drivers may independently decide to switch channels. Handle this by
updating the hostapd and wpa_supplicant AP and GO configuration.
Signed-hostap: Thomas Pedersen <c_tpeder@qca.qualcomm.com>
This avoids issues with some APs rejecting a reassociation if the
station is not currently associated as reported by Yossi Wortzel.
The change is based on a patch from Arik Nemtsov.
Signed-hostap: Jouni Malinen <j@w1.fi>
Use an empty IPv4 packet as the keep-alive packet for WNM BSS max idle
period mechanism. This is not really the best possible frame to use for
this, but for now, it can do until a more suitable frame is figured out
for this (e.g., special LLC header to indicate link test purposes).
Signed-hostap: Jouni Malinen <j@w1.fi>
If WNM is enabled for the build (CONFIG_WNM=y), add BSS max idle period
information to the (Re)Association Response frame from the AP and parse
this information on the station. For SME-in-wpa_supplicant case, add a
timer to handle periodic transmission of the keep-alive frame. The
actual request for the driver to transmit a frame is not yet
implemented.
Signed-hostap: Jouni Malinen <j@w1.fi>
The nl80211 driver interface does not allow 128-bit WEP to be used
without a vendor specific cipher suite and no such suite is defined for
this purpose. Do not accept WEP key length 16 for nl80211 driver
interface forn ow. wext-interface can still try to use these for
backwards compatibility.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Previusly the peer was assumed to not be operating a GO if the BSS entry
for it was not updated in the single scan run started by
p2p_connect-auto. This is not very robust since a scan may miss the peer
if either a Probe Request or Probe Response frame is lost. Improve
robustness by assuming the peer is still operating the GO and starting
the join operation. If the GO is not found during PD-for-join or the
single-channel scans during the join, fall back to GO Negotiation.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Do not try to associate with a network that has an invalid or incomplete
configuration because the association or at least data connection would
fail anyway. This commits adds a common function for checking whether a
network block is disabled to make it easier to check network blocks
without having to reject them during configuration file parsing (which
would prevent wpa_supplicant from starting). The only additional check
added in this commit is to verify the WEP key length. Similar checks for
other parameters can be added in future commits.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Both EAP-AKA and EAP-AKA' use USIM. Without this change, use of real
USIM card for EAP-AKA' was not allowed to proceed, i.e., only the
software simulated USIM operations were supported.
Signed-hostap: Jouni Malinen <j@w1.fi>
intended-for: hostap-1
Add support for HT STA to report 40 MHz intolerance to the associated AP.
A HT station generates a report (20/40 BSS coexistence) of channel list
if it finds a non-HT capable AP or a HT AP which prohibits 40 MHz
transmission (i.e., 40 MHz intolerant bit is set in HT capabilities IE)
from the scan results.
Parse the OBSS scan parameter from Beacon or Probe Response frames and
schedule periodic scan to generate 20/40 coexistence channel report if
requested to do so. This patch decodes Scan Interval alone from the OBSS
Scan Parameters element and triggers scan on timeout.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Make wpa_supplicant_event() more consistent by not checking
data in either location handling EVENT_RX_MGMT events. This event
is required to specify the data so this pointer cannot be NULL.
Signed-hostap: Jouni Malinen <j@w1.fi>
The GO can indicate that the P2P Group session is ending by sending a
Deauthentication frame with reason code 3 (Deauthenticated because
sending STA is leaving) based on P2P specification section 3.2.9. Use
this reason code to remove the P2P client group without waiting for the
group idle timeout.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Commit 2d43d37ff2 broke EVENT_RX_MGMT
processing in wpa_supplicant AP mode. ap_mgmt_rx() needs to be called
for Probe Request frames even if they get notified through the new
D-Bus signal mechanism.
Signed-hostap: Jouni Malinen <j@w1.fi>
Some applications require knowing about probe requests to identify
devices. This can be the case in AP mode to see the devices before they
connect, or even in P2P mode when operating as a P2P device to identify
non-P2P peers (P2P peers are identified via PeerFound signals).
As there are typically a lot of probe requests, require that an
interested application subscribes to this signal so the bus isn't always
flooded with these notifications. The notifications in DBus are then
unicast only to that application.
A small test script is also included.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
The signal strength is currently never used as the only driver reporting
it is nl80211 which uses IEEE80211_RADIOTAP_DB_ANTSIGNAL which is never
populated by the kernel. The kernel will (soon) populate
IEEE80211_RADIOTAP_DBM_ANTSIGNAL instead though, so use that.
Also, since it was never really populated, we can redefine the signal
field to be in dBm units only.
My next patch will also require knowing the signal strength of probe
requests throughout the code (where available), so add it to the
necessary APIs.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
Commit 6bf731e8ce broke handling of
EVENT_CHANNEL_LIST_CHANGED by introducing a cached copy of the driver
channel list that does not get updated even if driver changes its list.
Fix this by synchronizing the cacched wpa_s->hw.modes information
whenever EVENT_CHANNEL_LIST_CHANGED is processed. This fixes P2P channel
list updates based on regulatory domain hints that may trigger driver to
change its supported channel list.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
intended-for: hostap-1
When wpa_supplicant disconnects, e.g., due to authentication timeout,
we need to go through the EVENT_DISASSOC/DEAUTH processing similarly
to the driver triggered cases to get correct events delivered to the
ctrl_iface. Fix this by calling wpa_supplicant_event() in these cases
and by filtering out the confusing CTRL-EVENT-DISCONNECTED event with
all zeros BSSID.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
New global configuration parameters pcsc_reader and pcsc_pin can now be
used to initialize PC/SC reader context at start of wpa_supplicant.
Signed-hostap: Jouni Malinen <j@w1.fi>
This can be used to disable wpa_supplicant controlled roaming. It should
be noted that the WPA_DRIVER_FLAGS_BSS_SELECTION capability is the
preferred way for this and CONFIG_NO_ROAMING should be obsoleted once
drivers support the new NL80211_ATTR_ROAM_SUPPORT capability
advertisement.
Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
This makes WPA_INTERFACE_DISABLED more consistent in indicating that
wpa_supplicant cannot currently control the interface regardless of
whether the interface is disabled or completely removed.
Signed-hostap: Jouni Malinen <j@w1.fi>
intended-for: hostap-1
This fixes a build regression from commit
cd2f4ddfb9 by moving
wpa_supplicant_assoc_update_ie() outside the no-scan-processing ifdef
block.
Signed-hostap: Jouni Malinen <j@w1.fi>
Even though we may not update P2P peer entry while connected to the
peer as a P2P client, we should not be expiring a P2P peer entry while
that peer is the GO in a group where we are connected as a P2P client.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
When a P2P group is removed, we better not leave possibly started
sched_scan running. This could happen when a separate group interface
was not used.
In addition, it looks safer to explicitly stop sched_scan before
starting P2P Listen or Find operations to make sure the offloaded
scanning is not running when doing similar P2P operations.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This patch fixes an issue with roaming for drivers that set
WPA_DRIVER_FLAGS_BSS_SELECTION (currently ath6kl). On moving to an AP
with a different BSSID, an EVENT_ASSOC is received and the subsequent
4-way handshake may fail because of a mismatch between the RSN IE in
message 3/4 and in Beacon/Probe Response. This happens only when the APs
use different RSN IE contents and ap_scan is set to 1, since
wpa_supplicant fails to update its cached IEs.
Initial association may fail, too, in case of multiple APs with
the same SSID, since BSSID selection is done by the driver and again
a mismatch could be seen.
Fix these two issues by clearing and updating the cached IEs on
receiving an Association event from the driver. Also, retrieve the
scan results when the new BSS information is not present locally.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
The deauthentication and disassociation events from nl80211 were being
processed identically regardless of whether the frame was generated by
the local STA or the AP. This resulted in fast reconnection mechanism
getting triggered even in the case where the disconnection was detected
locally (e.g., due to beacon loss) while this was supposed to happen
only in the case where the AP is sending an explicit Deauthentication
or Disassociation frame with a specific reason code.
Fix this by adding a new deauth/disassoc event variable to indicate
whether the event was generated locally.
Signed-hostap: Jouni Malinen <j@w1.fi>
The internal sched_scanning state needs to be cleared on this event
even if the events happen to get ordered in a way that the interface
gets disabled just prior to EVENT_SCHED_SCAN_STOPPED event.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
If the driver was associated in station mode just before the AP mode was
started, the station mode disassociation event may end up getting
delivered to wpa_supplicant only after the AP mode has been started.
This can result in unexpected attempt to reassociate back to the network
that was previously used in station mode. Avoid this by ignoring the
disassociation event.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This event can be very frequent in AP mode when Beacon frames from
neighboring BSSes are delivered to user space. Drop the debug
message priority from DEBUG to EXCESSIVE for Beacon frames.
Signed-hostap: Jouni Malinen <j@w1.fi>
If Provision Discovery Request is sent for GO role (i.e., P2P Group ID
attribute is included), add the group interface name to the control
interface event on the GO. This makes it easier to figure out which
ctrl_iface needs to be used for wps_pbc/wps_pin command to authorize
the joining P2P client.
Signed-hostap: Jouni Malinen <j@w1.fi>
If the AP disconnects us with a reason code that indicates that it has
dropped the association, but could allow us to connect again, try to
reconnect to the same BSS without going through the full scan. This can
save quite a bit of time in some common use cases, e.g., when inactivity
timeout is used on the AP (and especially, when waking up from suspend
which has likely triggered some timeout on the AP).
Signed-hostap: Jouni Malinen <j@w1.fi>
This allows the MAC address of the interface to be changed when the
interface is set down even if the interface does not get completed
removed and re-added.
Signed-hostap: Jouni Malinen <j@w1.fi>
A disconnection event from the driver may end up getting delivered at a
time when wpa_supplicant is not even trying to connect (e.g., during a
scan that was already started after WPS provisioning step). In such a
case, there is not much point calling wpas_connection_failed() and
skipping this avoids confusing attempts of re-starting scanning while
the previous scan is still in progress.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This cleans up the source code and makes it less likely that new AKM
addition misses some needed changes in the future.
Signed-hostap: Jouni Malinen <j@w1.fi>
The new event can be used when EAPOL TX status can't be reported as a
complete 802.11 frame but is instead reported as just the EAPOL data as
originally passed to hapd_send_eapol().
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
The P2P_FIND command was failing if it was issued at the moment when
a scan operation was in progress. Avoid returning failure in this
case by scheduling the P2P find to start once the ongoing scan is
completed.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
wpa_supplicant_rsn_preauth_scan_results() needs to be called to
update RSN pre-authentication candidates. This cannot be done before
the wpa_supplicant_connect() call on the first association, but when
trying to figure out whether to roam, it is fine to do so for the
case when roaming is skipped.
Signed-hostap: Jouni Malinen <j@w1.fi>
The eloop timeout to stop TKIP countermeasures has to be canceled
on deinit path to avoid leaving bogus timeouts behind.
Signed-hostap: Jouni Malinen <j@w1.fi>
At least with driver_test.c, the BSS table may not include frequency
information. In such a case, we need to skip rate set matching during
BSS selection to avoid rejecting valid AP.
Signed-hostap: Jouni Malinen <j@w1.fi>
Once PBC overlap detected when using dynamic group interfaces, the wpa_s
corresponding to P2P group interface is freed. This patch avoids
accessing the wpa_s data structure after it is freed. This fixes a
possible crash in P2P client role in such a case.
Disable the direct connection when a TDLS peer stops responding
to packets, as indicated by the "LOW ACK" event coming from a driver.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Cc: Kalyan C Gaddam <chakkal@iit.edu>
When a driver does not implement the TDLS_TEARDOWN operation internally,
send an explicit TDLS link teardown frame to the driver.
Change all teardown calls to use these calling semantics.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Cc: Kalyan C Gaddam <chakkal@iit.edu>
Register for the TDLS discovery response public action frame in nl80211.
Print out a debug message when a Discovery Resp frame is received and
validated.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Cc: Kalyan C Gaddam <chakkal@iit.edu>
IEEE Std 802.11-2007 7.3.2.2 demands that in order to join a BSS all
required basic rates have to be supported by the hardware.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
This code was used only with driver_test.c to allow MLME operations
in hostapd to be tested without having to use a real radio. There
are no plans on extending this to any other use than testing and
mac80211_hwsim has now obsoled the need for this type of testing.
As such, we can drop this code from wpa_supplicant to clean up the
implementation of unnecessary complexity.
This offloads the station polling to driver wrappers, which may offload
it again to the driver. The hostap driver wrapper uses "real" data
frames while nl80211 uses null data frames.
Also add a specific event to indicate that a poll was successful for
future use with the nl80211 driver.
"hostapd_cli ess_disassoc (STA addr) (URL)" can now be used to send
an ESS Dissassociation Imminent notification to the STA. This event
is shown in wpa_supplicant ctrl_iface monitors (e.g., wpa_cli):
"WNM: ESS Disassociation Imminent - session_info_url=http://example.com/session/"
EVENT_WPS_BUTTON_PUSHED wpa_supplicant_event can now be used in
station mode driver_*.c to indicate that a push button has been
pushed. This will activate WPS PBC mode.
This patch uses sched_scan, if available, when the driver is
initialized. It also adds a couple of cancel operations where
appropriate.
Signed-off-by: Luciano Coelho <coelho@ti.com>
In new Linux kernel versions (>=3.0), nl80211 adds scheduled scan
capability. In order to use this feature to its full extent, we need
to support it in the wpa_supplicant core, so that it can also be used
by other drivers.
This commit adds initial scheduled scan support operations and events.
Signed-off-by: Luciano Coelho <coelho@ti.com>
This allows the AP to be selected based on the BSSID when WPA-PSK
is used with a passphrase. The PSK will be derived from the passphrase
after the SSID has been learned from scan results.
This implements GAS request mechanism that is aimed at being used to
replace use case specific GAS/ANQP implementations in the future.
Compared to the earlier implementation in P2P SD, this implementation
includes support for multiple concurrent requests and more thorough
validation of frames against the pending query data.
GAS header processing, including comeback and reassembly, are handled
within gas_query.c and the users of this module will only need to
provide the Query Request and process the (possibly reassembled)
Query Response.
If the driver indicates that it supports BSS selection (including
roaming within an ESS) with WPA_DRIVER_FLAGS_BSS_SELECTION, modify
ap_scan=1 mode to behave like ap_scan=2 mode for BSS selection.
The initial scan is still done to avoid the need for strict
configuration of or security parameters (e.g., to figure out whether
TKIP or CCMP is being used as the group cipher). However, when
requesting the driver to connect, the bssid and freq parameters are
not provided to leave the driver in control of selecting which BSS
to use and to allow the driver to decide when to roam.
Only accept Probe Request frames that have a Wildcard BSSID and a
destination address that matches with our P2P Device Address or is the
broadcast address per P2P specification 3.1.2.1.1.
Add support to wpa_supplicant for device-based GTK rekeying. In order to
support that, pass the KEK, KCK, and replay counter to the driver, and
handle rekey events that update the latter.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Previous ft_ies needs to be removed before supplicant starts a new FT
initial association and this requires the ft_used state to be cleared
here.
Signed-off-by: Hong Wu <hong.wu@dspg.com>
Regardless of how the AP mode is disabled, wpa_supplicant_ap_deinit()
must be called. Make sure this happens on all paths by calling the
deinit function from wpa_supplicant_mark_disassoc().
These checks were previously skipped if the scan result included WPA
or RSN IE. However, that can result in selecting a network that does
not match local configuration in some cases.
Processing of the scan results for RSN pre-authentication candidates
was moved to happen before the network was selected. This resulted in
all candidates being dropped due to no SSID having been configured.
Fix this by moving the processing to happen after the network has
been selected. Since the raw scan results are not available at that
point, use the BSS table instead of scan results to fetch the
information.
Both the SA and IEs from the received Probe Request frames must be
included and the Probe Request RX callback functions may assume that
these are not NULL.
It is now possible to configure the the time in seconds that
wpa_supplicant waits before requesting a new scan after failing to find
a suitable network in scan results.
Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
If WPA/WPA2 was enabled in the configuration, the non-WPA exception
could allow an incorrect AP to be selected from scan results. Do
not use the exception if WPA/WPA2 is enabled in configuration.
Change the old design of running a single long living RSN IBSS
instance to keep a separate instance for each IBSS connection.
This fixes number of issues in getting keys set properly for
new connections and is in general quite a bit more correct
design.
Move the code snippet to switch on bgscan over to wpa_supplicant.c
from event.c, so that it can be activated on wpa_supplicant_set_state().
Also create a centralized place to switch off bgscan. bgscan is now
turned on in COMPLETED, not ASSOCIATED.
When wpa_s scans in AP mode, it doesn't propagate the scan event to the
AP code, so that code can get stuck if it uses the callbacks there.
Simply call them where appropriate.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This allows driver wrappers to indicate whether the association was
done using Association Request/Response or with Reassociation
Request/Response frames.
The DBus code will want to have perfect matching of dev_found and the
dev_lost it adds so it doesn't need to keep track internally. Enable
that with a new flag in the core that tracks whether we have already
notified about this -- the existing users can ignore it.
The part where this is always set to 1 if the new device is discovered
by a driver that has P2P in the driver is buggy -- the driver should
feed the P2P peer database and then that should feed the notification
here instead.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This embeds some information about each P2P peer that will be publically
visible in a struct that is shared.
The dev_found notification function is also passed the new struct, which
requires some work for the driver-based P2P management.
Signed-off-by: Konguraj(Raj) Kulanthaivel <konguraj.kulanthaivel@intel.com>
Signed-off-by: Fabien Marotte <fabienx.marotte@linux.intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
mac80211 authentication or association operation may get stuck for some
reasons, so wpa_supplicant better use an internal timer to recover from
this.
Signed-off-by: Ben Greear <greearb@candelatech.com>
When FT protocol run is completed with FT-EAP, the EAPOL state machine
needs to be notified of the completed authentication to make sure it
does not try to start new authentication.
