This allows external programs to use vendor specific information from
P2P peers without wpa_supplicant having to be able to parse and
understand all such vendor specific elements.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This adds following new control interface commands to allow arbitrary
vendor elements to be added into number of frames:
VENDOR_ELEM_ADD <frame id> <hexdump of elem(s)>
VENDOR_ELEM_GET <frame id>
VENDOR_ELEM_REMOVE <frame id> <hexdump of elem(s)>
VENDOR_ELEM_REMOVE <frame id> *
The following frames are supported in this commit (additional frames can
be added in the future):
0 = Probe Request frame in P2P device discovery
1 = Probe Response frame from P2P Device role
2 = Probe Response frame from P2P GO
3 = Beacon frame from P2P GO
4 = PD Req
5 = PD Resp
6 = GO Neg Req
7 = GO Neg Resp
8 = GO Neg Conf
9 = Invitation Request
10 = Invitation Response
11 = P2P Association Request
12 = P2P Association Response
One or more vendor element can be added/removed with the commands. The
hexdump of the element(s) needs to contain the full element (id, len,
payload) and the buffer needs to pass IE parsing requirements to be
accepted.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This will be useful in wpa_supplicant part to signal if a peer got its
group changed.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Previously, eight character random passphrase was generated
automatically for P2P GO. The new p2p_passphrase_len parameter can be
used to increase this length to generate a stronger passphrase for cases
where practicality of manual configuration of legacy devices is not a
concern.
Signed-off-by: Jouni Malinen <j@w1.fi>
Performing a P2P Device flow such as p2p_listen or
p2p_find, can degrade the performance of an active interface
connection, if the listen frequency is different than the
frequency used by that interface.
To reduce the effect of P2P Device flows on other interfaces,
try changing the listen channel of the P2P Device to match the
operating channel of one of the other active interfaces. This change
will be possible only in case that the listen channel is not forced
externally, and will be delayed to a point where the P2P Device
state machine is idle.
The optimization can be configured in the configuration file and
is disabled by default.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
The dev_found() callback from NFC connection handover message processing
ended up using the p2p_dev_addr pointer that points to the parsed
message. However, that parsed data was freed just before the call. Fix
this by reordering the calls.
Signed-off-by: Jouni Malinen <j@w1.fi>
If p2p_listen is called while previous listen command's
remain_on_channel event is pending, the p2p_listen would fail
and it used to clear pending_listen_freq. Now when the remain-
on-channel event comes from the driver, the pending_listen_freq
doesn't match and gets ignored. This was leading to a case
where listen state was getting stuck (in case of WAIT_PEER_CONNECT
state).
Signed-off-by: Jithu Jance <jithu@broadcom.com>
Peer should handle a GO Negotiation exchange correctly when the
responding device does not have WSC credentials available at the
time of receiving the GO Negotiation Request. WSC Credentials
(e.g., Pushbutton) can be entered within the 120 second timeout.
Presently, if concurrent session is not active, the peer would wait for
GO Negotiation Request frame from the other device for approximately one
minute due to the earlier optimization change in commit
a2d6365760. To meet the two minute
requirement, replace this design based on number of iterations with a
more appropriate wait for the required number of seconds.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Extend the previous commit 0f1034e388 to
skip extended listen also based on ongoing provision discovery operation
(which does not show up as a separate P2P module state and as such, was
not coveraged by the previous commit).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Do not perform extended listen period operations when either a P2P
connection is in progress. This makes the connection more robust should
an extended listen timer trigger during such an operation.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The previous check for dl_list_len() or having an entry from the list is
sufficient, but some static analyzers cannot figure out that
dl_list_first() and dl_list_last() will return non-NULL in this type of
cases. Avoid invalid reports by explicitly checking for NULL.
Signed-off-by: Jouni Malinen <j@w1.fi>
p2p_freq_to_channel() could return an error if the GO or P2P Client
operating channel is not valid. Check for this before generating the NFC
handover message.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
wpa_supplicant now retries for P2P_GO_NEG_CNF_MAX_RETRY_COUNT times if
it doesn't receive acknowledgement for GO Negotiation Confirmation
frame. Currently, P2P_GO_NEG_CNF_MAX_RETRY_COUNT is set to 1.
While this is not strictly speaking following the P2P specification,
this can improve robustness of GO Negotiation in environments with
interference and also with peer devices that do not behave properly
(e.g., by not remaining awake on the negotiation channel through the
full GO Negotiation).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Scan for GO on the negotiated operating channel for few iterations
before searching on all the supported channels during persistent group
reinvocation. In addition, use the already known SSID of the group in
the scans. These optimizations reduce group formation time.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This moves some of the p2p_prepare_channel_best() functionality into
separate helper functions to make the implementation easier to read.
Signed-off-by: Jouni Malinen <j@w1.fi>
Commit 94b84bc725 missed one path where
p2p->op_reg_class should have been updated. Set this to 81 during
operating channel selection from 2.4 GHz.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Do not select pre-configured channel as operating channel preference if
it is unavailable maybe due to interference or possible known
co-existence constraints, and try to select random available channel.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Previously, both this and combination of OUI_WFA and P2P_OUI_TYPE were
used. Using the full 32-bit value as a single operation saves a bit in
code size, so start moving towards using it more consistently when
writing or finding the P2P vendor specific element.
Signed-off-by: Rahul Jain <rahul.jain@samsung.com>
PD Response is sent out using a 200 ms offchannel wait, but that wait
was not cancelled on TX status report. This could result in offchannel
operation being left waiting unnecessarily long. Fix this by making the
P2P_NO_PENDING_ACTION case in Action TX callback cancel the wait if a
pending wait is marked (and mark this for PD Response).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
When a Probe Request frame from an invitation peer is received, a timer
is schedule to start invitation. However, this could have been scheduled
multiple times (once per Probe Request frame) which is undesirable since
only a single invitation should be initiated.
Signed-off-by: Rahul Jain <rahul.jain@samsung.com>
It looks like discovery_dev_id test case can still fail and based on the
previously added debug prints, this is happening since the P2P module
believes it is not in Listen state even when a P2P_LISTEN was issued.
p2p_listen_cb() did not get called on remain-on-channel event for some
reason, so lets add more debug to find out why this can happen.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Suppose we have multiple peers and we have peers advertising SD
capability, but no services registered for advertising. In this case,
even if there are multiple broadcast queries set, we might end up
sending only the lastly added broadcast query to the same device (since
SD_INFO won't get set for the first broadcast query). Add support for
multiple wildcard queries to be tracked to enable this type of use
case.
Some times it is seen that before advancing to next device in the list,
the scan results come and update SD_SCHEDULE flag. This will result in
sending the already sent query to the same device without giving chance
to other devices. This issue again is seen with peer devices advertising
SD capability without any services registered.
Signed-off-by: Jithu Jance <jithu@broadcom.com>
It can be helpful to see from the debug log why the P2P Device role did
not reply to a Probe Request frame.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
It was possible to FAIL return for a P2P_FIND command that was issued
while an already started P2P_FIND operation was in the scan phase. This
can be confusing for upper layer software, so hide the failure report
from the ctrl_iface response. The previously started scan will continue
the find operation after this.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
If the peer device has already acknowledge receipt of the Invitation
Request frame, it is better not to re-start invitation by sending
another Invitation Request. This should not be needed since the peer
already has received the Invitation Request frame and sending the second
round in this type of sequence can cause issues with nl80211 offloaded
offchannel TX operations since driver_nl80211.c will lose the cookie
value for the first pending Action frame and may not be able to cancel
offchannel wait for it properly. this has been seen to trigger a failure
in the p2p_go_invite_auth test case with the scan failing due to GO
sending out Probe Response frame on incorrect channel (the channel used
in that not-cancelled Action TX).
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
1. In wpa_config_process_bgscan() fix memory leak after
calling wpa_config_parse_string()
2. In hostapd_config_defaults(), on failure to allocate bss->radius,
conf->bss was not freed.
3. In p2p_deauth_nofif(), memory allocated in p2p_parse_ies() was not
freed in case of NULL minor_reason_code.
4. In p2p_disassoc_nofif(), memory allocated in p2p_parse_ies() was
not freed in case of NULL minor_reason_code.
5. In p2p_process_go_neg_conf(), memory allocated was not freed in
case that the P2P Device interface was not waiting for a
GO Negotiation Confirm.
6. In wpa_set_pkcs11_engine_and_module_path(), the wrong pointer was
checked.
Signed-hostap: Eytan Lifshitz <eytan.lifshitz@intel.com>
This adds a new P2P Invitation mechanism to invite a P2P Device with an
NFC Tag to an already operating group when the GO with NFC Device reads
the NFC Tag. The P2P Device with the NFC Tag will then accept invitation
and connect to the group automatically using its OOB Device Password.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
P2P Group ID can optionally be included in the connection handover
messages when acting as a P2P Client in a group. Add this information
and show it in the P2P-NFC-PEER-CLIENT event message.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
When the NFC connection handover message received from a peer indicates
that the peer is operating as a GO on a specific channel, use that
information to avoid having to go through full scan. In addition, skip
the separate join-a-group scan since we already know the operating
channel, GO P2P Device Address, and SSID.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Instead of automatically triggering a connection, provide an indication
of one of the devices being a P2P client to upper layers to allow user
to determine what to do next.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Send a P2P-NFC-BOTH-GO event to upper layers to determine what to
do in case both devices going through NFC connection handover are
already operating as a GO.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
When NFC connection handover is used to trigger GO Negotiation, the
channel used for the GO Negotiation frames is already known. As such,
there is no need to use the Listen operations to find the peer.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The device with the NFC Tag can be configured to enable NFC to be used
with "P2P_SET nfc_tag 1" and "P2P_LISTEN" commands to allow static
handover to be used.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
"NFC_REPORT_HANDOVER {INIT,RESP} P2P <req> <sel>" can now be used to
report completed NFC negotiated connection handover in which the P2P
alternative carrier was selected.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
"NFC_GET_HANDOVER_{REQ,SEL} NDEF P2P-CR" can now be used to build P2P
alternative carrier record for NFC connection handover request/select
messages.
Static connection handover case can be enabled by configuring the DH
parameters (either with wps_nfc_* configuration parameters or with
WPS_NFC_TOKEN command at run time. The NFC Tag contents can be generated
with "NFC_GET_HANDOVER_SEL NDEF P2P-CR-TAG" after having configured
Listen channel (p2p_listen_reg_class/p2p_listen_channel).
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
GO Negotiation needs to know which OOB Device Password ID is assigned
for the peer when NFC is used as the trigger.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The new default value (from 300 to 60 seconds) makes the internal P2P
peer list somewhat faster to react to peers becoming unreachable while
still maintaining entries for some time to avoid them disappearing
during user interaction (e.g., selecting a peer for a connection or
entering a PIN).
Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
A P2P Device while in the Listen state waiting to respond for the
obtained group negotiation request shall give a fair chance for other
concurrent sessions to use the shared radio by inducing an idle time
between the successive listen states. However, if there are no
concurrent operations, this idle time can be reduced.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This adds one more case of active P2P peer detection so that
p2p_expire_peers() cannot hit a case where a GO Negotiation peer would
be removed.
Signed-hostap: Jithu Jance <jithu@broadcom.com>
Avoid concurrent P2P scan requests with any other exclusive use of the
radio by using the radio work queuing mechanism. This removes some of
the earlier workarounds that postponed scans depending on other
operations.
Signed-hostap: Jouni Malinen <j@w1.fi>
The P2P_PRESENCE_REQ command did not give any easily available
indication of the response received from the GO. Make this more useful
by providing such response (if received) as a ctrl_iface monitor event
(P2P-PRESENCE-RESPONSE).
Signed-hostap: Jouni Malinen <j@w1.fi>
The BSS table, scan timeout, and related functionality should use
monotonic time since they care about relative values (age) only.
Unfortunately, these are all connected, so the patch can't be split
further. Another problem with this is that it changes the driver wrapper
API. Though, it seems only the test driver is using this.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
Some devices disable use of U-NII-1 (channels 36-48) for P2P due to it
being indoor use only in number of locations. If U-NII-3 (channels
149-161) is available, try to pick a channel from that range first
during random channel selection to reduce likelihood of interoperability
issues.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
If there are no other preferences from local configuration or driver,
prefer a random VHT channel instead of falling back to the fixed
pre-configured channel or 5 GHz/HT40 channel preference.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
If there are no other preferences from local configuration or driver,
prefer a random HT40 channel instead of falling back to the fixed
pre-configured channel or 5 GHz channel preference.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
If there are no other preferences from local configuration or driver,
prefer a random 5 GHz channel instead of falling back to the fixed
pre-configured channel (which is selected by default to be 1, 6, or 11).
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
During persistent group re-invocation, GO may end up using a different
channel as the operation channel compared to what was indicated in the
invitation frames. This may break the connection if the peer device ends
up scanning the GO only on the channel from the invitation frame. Fix
this by using the negotiated channel (if available) on the GO as the
operating channel instead of the channel that was provided in the
p2p_invite command to start negotiation.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
When WFD Subelements are set, the IE in the Beacon frames of already
existing groups are not updated. This patch fixes this issue by setting
beacon_update to be 1 on WFD IE update.
Signed-hostap: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
The new p2p_add_cli_chan=1 configuration parameter can be used to
request passive-scan channels to be included in P2P channel lists for
cases where the local end may become the P2P client in a group. This
allows more options for the peer to use channels, e.g., if the local
device is not aware of its current location and has marked most channels
to require passive scanning.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
