This fixes issues where a GO used offchannel-TX operation to send an
Invitation Request frame. Wait for the offchannel TX operation needs to
be stopped as soon as the Invitation Response frame has been received.
This addresses some issues where Probe Response frame from the GO
through the monitor interface may end up going out on a wrong channel
(the channel of this offchannel TX operation for invitation).
Signed-hostap: Jouni Malinen <j@w1.fi>
Join-a-group needs to force the current operating channel of the target
group as the frequency to use for the PD exchange. When the channel was
selected based on a BSS entry for the GO, this worked only for the first
PD Request frame while the retries reverted to a potentially different
channel based on a P2P peer entry. Fix this by maintaining the forced
channel through the PD retry sequence.
Signed-hostap: Jouni Malinen <j@w1.fi>
P2P Invitation Response frame is required to include the Channel List
attribute only in Status=Success case. Skip the debug message claiming
that a mandatory attribute was not included in non-Success case.
Signed-hostap: Jouni Malinen <j@w1.fi>
In noisy environment peer may take more time to send Invitation
Response so increase Invitation Response timeout to 500 ms in success
case and also increase Invitation Request action wait time to 500 ms.
This makes the Invitation Request case use the same timeout with GO
Negotiation.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
When no other user preference is specified, opt to use an operating
channel that allows 5 GHz band to be used rather than 2.4 GHz.
Previously, this was already done in practice for HT40 channels since no
such channel is enabled for P2P on 2.4 GHz. This commit extends this to
apply 5 GHz preference for 20 MHz channels as well.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Even after listen duration is over, P2P module remained in
P2P_LISTEN_ONLY state, which is blocking station mode scans. Fix this by
stopping P2P listen explicitly to update p2p_state to IDLE when listen
duration expires.
Signed-hostap: Syed Asifful Dayyan <syedd@broadcom.com>
If the device that sends the GO Negotiation Confirm becomes the GO, it
may change its operating channel preference between GO Negotiation
Request and Confirm messages based on the channel list received from us.
Previously, the peer operating channel preference was not updated in
such a case and this could result in the initial scans after GO
Negotiation using incorrect operating channel and as such, extra delay
in the connection process. Fix this by updating the operating channel
information from GO Negotiation Confirm in cases where the peer becomes
the GO.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
If there are no higher priority preference for the operating channel,
use the first pref_chan entry as the operating channel preference over
the pre-configured channel which is not really a good indication of
preference. This changes the behavior for GO Negotiation Request frame
operating channel preference value in cases where p2p_pref_chan list is
set.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Add additional input verification for the frequency parameter in
p2p_group_add (and other P2P operations for that matter). Without this
verification invalid freq could be set and not handled properly.
Signed-hostap: Ilan Peer <ilan.peer@intel.com>
If AP mode SME/MLME within wpa_supplicant is used for processing Probe
Request frames in GO mode, drop Probe Request frames that include only
802.11b rates per P2P spec section 2.4.1.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
In a noisy enviromment, some peers can be slow to respond to the
invitation request frames which may lead to unnecessary state timeout.
Increase this timeout to 350 ms to improve the probabilty of
successfully receiving the invitation response frames.
Signed-hostap: Vivek Natarajan <nataraja@qca.qualcomm.com>
When STA interface is connected and P2P interface gets invited in a
different channel from previous P2P group, the invitiation would fail
because of no common channel found. Fix this by using different logic
when device support multi channel concurrency.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Replace direct wpa_msg() calls with p2p_dbg(), p2p_info(), and p2p_err()
calls that use a new debug_print() callback to handle actual debug
printing outside the P2P module.
Signed-hostap: Jouni Malinen <j@w1.fi>
This removes wpa_ctrl.h dependency from src/p2p/* and makes the P2P
events more consistent, i.e., everything that is aimed for upper layer
processing from the wpa_supplicant control interfaces is generated in
p2p_supplicant.c.
Signed-hostap: Jouni Malinen <j@w1.fi>
Allow invitation exchange to update operating channel selection after
peer channel list has been received similarly to how GO negotiation was
handled.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
All P2P use cases are required to use the global operating table and
there is no need to need to try to maintain some backwards compatibility
with country code -specific values. Clean up the implementation by
removing the unnecessary country parameter.
Signed-hostap: Jouni Malinen <j@w1.fi>
Commit fb8984fd6f added a mechanism to
skip the Listen state when the peer is expected to be waiting for us to
initiate a new GO Negotiation. However, this flag was set when building
the GO Negotiation Response frame with status 1 regardless of whether we
managed to send that frame or peer receive it. This could result in GO
Negotiation failures in cases where the peer did not receive the
response and Listen channels of the devices were different. Fix this by
setting the flag only after TX status indicating success has been
received.
This fixes frequent failures shown for the test_grpform_pbc hwsim test
case.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
When Action frame TX is postponed until a pending p2p_scan completes,
there may be additional operations that need to be continued after the
postponed Action frame TX operation completes. Fix this by starting
pending operation (if any) from TX status event for after_scan_tx
frames.
This fixes common errors seen with the test_discovery hwsim test case.
Signed-hostap: Jouni Malinen <j@w1.fi>
As per P2P specification v1.2: "The P2P Group Info attribute shall be
omitted if there are zero connected P2P Clients."
Do not add the attribute if there are not connected peers.
Signed-hostap: Chaitanya T K <chaitanya.mgit@gmail.com>
Commit 6b56cc2d97 added a possible call to
p2p_reset_pending_pd() prior to checking config_methods match between
our request and peer response. That reset call could clear
dev->req_config_methods and as such, result in unexpected
P2P-PROV-DISC-FAILURE report here even in cases where the peer accepts
the provision discovery. Fix this by using a local copy of the
req_config_methods variable.
Signed-hostap: Jouni Malinen <j@w1.fi>
In some cases where the ack for Invitation response is lost,
the device is stuck in invited state but the peer device starts
GO. In line with the implementation of Negotiation Confirm,
assume invitation response was actually received by the peer
even though ack was not reported.
Signed-hostap: Vivek Natarajan <nataraja@qca.qualcomm.com>
Previously, P2P_PD_DURING_FIND state was scheduled for 200 ms and the
P2P state was not change until that timeout regardless of whether the PD
Response for recieved or not. There is no need to wait for that timeout
if the response is received, so allow the next operation to be performed
immediately after the response has been processed.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
If a peer replies to persistent group invitation with status code 8
(unknown group), remove the peer from the p2p_client_list if we are the
GO or remove the persistent group if we are the P2P client since it
looks like that the peer has dropped persistent group credentials and
the provisioning step needs to be executed again.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Commit 50285f5ca8 changed number of rules
in channel selection and among other things, it broke the design where
the currently used operating channel on a virtual interface that is
shared by the same radio is preferred to avoid costs related to
multi-channel concurrency. Fix this regression by making the P2P module
aware of the shared channel and using that preference as the highest
priority when re-selecting the channel during negotiation.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Commit 50285f5ca8 ended up forcing channel
re-selection in number of cases where the peer would actually have
accepted our initial preference. Fix the parts related to best channel
information by using best_freq_overall as the highest priority and by
skipping the band changes if the peer supports the channel that we
picked since these were based on the assumption that
p2p_reselect_channel() is called only if the peer could not accept our
initial choice which is not the case anymore.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
It is possible for a P2P client to connect to an operating group without
exchanging any Probe Request/Response frames that would allow the GO to
discover the peer. To make sure there is a P2P peer entry at the GO, try
to add the peer information based on P2P IE in (Re)Association Request
frame.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Peer device includes its list of allowed operating channels in the
Invitation Response frame. When we are becoming the GO, use that list
from the peer to filter out acceptable channels to avoid selecting a
channel that the peer is unable to use.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
When re-invoking a persistent group in P2P client role, the new
pref=<MHz> parameter can now be used with the p2p_invite command to
indicate a preferred operating frequency. Unlike the older freq=<MHz>
parameter, this leaves GO an option to select another channel (from our
supported channels) if the GO cannot accept the channel.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
If multi channel concurrency is supported, we have to populate the
p2p_channels with list of channels that we support. Use the same design
that was previously added for GO Negotiation.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Commit fb8984fd6f cleared wps_method to
WPS_NOT_READY in p2p_stop_find_for_freq() as an attempt to clear
authorization when a group formation is cancelled. However, this code
path is hit also in cases where the user did not actually cancel
anything (e.g., from p2p_process_go_neg_req()). As such, it is not fine
to clear wps_method here even if it could be proper for some cases. For
now, revert that part to avoid regressions and consider clearing
wps_method on cancel separately.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
In case we have replied to a peer's GO Negotiation Request frame with a
GO Negotiation Response frame using status code
info-currently-unavailable (1), the peer is likely going to wait for us
to initiate GO Negotiation on its Listen channel. We were previously
using alternativing send-GO-Neg-Req and Listen phase when providing that
response after the user had authorized the connection. However, the
Listen phase here is unnecessary in this case and will make the
connection take longer time to go through. Skip the Listen phase and
make the wait-for-GO-Neg-Resp timeout random between 100 and 200 ms to
avoid getting in sync with the peer. In practice, this will make us
retry GO Negotiation Request frames more frequently and remain on the
peer's Listen channel for most of the time when initiating GO
Negotiation after status=1 response.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
There may be environments in which large number of devices are operating
on the social channels. In such cases, it is possible for the Action
frame TX operation wait for quite long time before being able to get the
frame out. To avoid triggering GO Negotiation failures, increase the
timeouts for GO Neg Req (with TX ACK) and GO Neg Resp (with or without
TX ACK as long as status=0) to 500 ms.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
It is possible for the driver to indicate multiple Probe Request frames
that would be processed in a single loop. If those frames happen to be
from a peer which with we are trying to start GO Negotiation, multiple
timeouts to start GO Negotiation (p2p_go_neg_start) could end up being
scheduled. This would result in confusing burst of multiple GO
Negotiation Request frames being sent once the RX loop finally
concludes. Avoid this by scheduling only a single eloop timeout to
trigger GO Negotiation regardless of how many Probe Request frames from
the peer is received. In addition, make sure this timeout gets canceled
in p2p_deinit().
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
If we have already sent out GO Negotiation Response and are waiting for
the peer to reply with GO Negotiation Confirm, there is no point in
re-starting GO Negotiation based on Probe Request frame from the peer.
Doing that would just result in confusing GO Negotiation exchange with
multiple sessions running at the same time.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The device that is selected as the GO shall incode P2P Group ID
attribute in GO Negotiation Response/Confirm message. Previously we did
not reject a message without that attribute since it was possible to
continue operations even without knowing the SSID. However, this can
potentially result in confusing results since missing P2P Group ID
attribute can be a sign of conflicting GO role determination (both
devices assuming the peer is the GO). To get clearer end result for the
GO Negotiation, reject this as a fatal error. In addition, stop GO
Negotiation if GO Negotiation Confirm indicates non-zero status since
that is also a fatal error.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Commit 624b4d5a64 changed GO Negotiation
to use the same Dialog Token value for all retransmissions of the GO
Negotiation Request within the same session. However, it did leave the
tie breaker bit changing for each frame. While this should not have
caused issues for most cases, it looks like there are possible sequences
where the peer may end up replying to two GO Negotiation Request frames
with different tie breaker values. If in such a case the different GO
Negotiation Response frames are used at each device, GO role
determination may result in conflicting results when same GO intent is
used.
Fix this by assigning the tie breaker value at the same time with the
dialog token (i.e., when processing the p2p_connect command instead of
for each transmitted GO Negotiation Request frame) to avoid issues with
GO selection.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The driver may have cached (e.g., in cfg80211 BSS table) the scan
results for relatively long time. To avoid reporting stale information,
update P2P peers only based on results that have based on frames
received after the last p2p_find operation was started.
This helps especially in detecting when a previously operating GO stops
the group since the BSS entry for that could live for 30 seconds in the
cfg80211 cache. Running p2p_flush followed by p2p_find will now allow
wpa_supplicant to not add a P2P peer entry for that GO if the group had
been terminated just before that p2p_flush command. Previously, that GO
could have been indicated as a newly found device for up to 30 seconds
after it had stopped the group.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
For various P2P use cases, it is useful to have more accurate timestamp
for the peer information update. This commit improves scan result
handling by using a single timestamp that is taken immediately after
fetching the results from the driver and then using that value to
calculate the time when the driver last updated the BSS entry. In
addition, more debug information is added for P2P peer updates to be
able to clearly see how old information is being used here.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
If we discover a P2P peer based on a Beacon frame from the GO role, we
do not get information about the supported configuration methods. This
can result in issues if the P2P managing entity above wpa_supplicant is
not prepared to handling config_methods=0x0. To avoid this, postpone
reporting of the P2P-DEVICE-FOUND event when this happens on one of the
social channels. It would be good to be able to this on all channels,
but that could result in issues of never indicating the event for a peer
that is operating a GO on a channel that requires passive scanning.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
It could be possible for the scan results to include two entries for a
peer, one from the Listen state and the second one from the GO role. The
latter could be based on a Beason frame. If that happens and the entry
from GO is processed last, the P2P peer config_methods value could
potentially get cleared since Beacon frames do not include this
information in either WPS or P2P element. Avoid this by allowing the
config_methods value for P2P peers to be updated only if the new value
is non-zero.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
When pending p2p_find fails we need to send p2p_stop_find event to
indicate the previous p2p_find command has been processed.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Commit 1a9f6509b3 added support for
fragmenting the P2P IE in Probe Response frames from a GO. However, it
did not take into account the possibility of Wi-Fi Display IE being
included in the same buffer and caused a regression for the cases where
Wi-Fi Display is enabled. Fix this by building the possibly fragmented
P2P IE first and then concatenating the separate IEs together.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The P2P-FIND-STOPPED event was sent only in the P2P_SEARCH state, but
this needs to be send also in the new continue-search-when-ready states
P2P_CONTINUE_SEARCH_WHEN_READY and P2P_SEARCH_WHEN_READY for consistent
behavior.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Each GO Negotiation Request is (re)tried with an unique dialog token and
a GO Negotiation Response / Confirmation from the peer with a mismatched
dialog token is ignored which could result in a failure in this group
formation attempt. Thus, the P2P device would continue retrying the GO
Negotiation Request frames till the GO Negotiation Response frame with a
matching dialog token is received. To avoid the failures due to the
dialog token mismatch in retry cases if the peer is too slow to reply
within the timeout, the same dialog token value is used for every retry
in the same group formation handshake.
It should be noted that this can result in different contents of the GO
Negotiation Request frame being sent with the same dialog token value
since the tie breaker bit in GO Intent is still toggled for each
attempt. The specification is not very clear on what would be the
correct behavior here. Tie breaker bit is not updated on
"retransmissions", but that is more likely referring to the layer 2
retransmission and not the retry at higher layer using a new MMPDU.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This commit increases the maximum buffer size for P2P Client Info
advertized by the Group Owner in the Probe Response frames.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Commit 175171ac6c ensured that the PD
requests are retried in join-a-running group case and the Enrollee is
started on either receiving the PD response or after the retries. Each
PD request is retried with an unique dialog token and a PD response from
the GO with a mismatched dialog token is ignored. Thus, the P2P client
would continue retrying the PD requests till the response with a
matching dialog token is obtained. This would result in the GO getting
multiple PD requests and a corresponding user notification (POP UP) in
implementations where each PD request results in a POP UP, resulting in
a bad user experience. To avoid such behavior, the same dialog token
value is used for every retry in the same PD exchange.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
