This allows both hostapd and wpa_supplicant to be used to derive and
configure keys for GCMP. This is quite similar to CCMP key
configuration, but a different cipher suite and somewhat different rules
are used in cipher selection. It should be noted that GCMP is not
included in default parameters at least for now, so explicit
pairwise/group configuration is needed to enable it. This may change in
the future to allow GCMP to be selected automatically in cases where
CCMP could have been used.
This commit does not included changes to WPS or P2P to allow GCMP to be
used.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Use the NL80211_IFACE_COMB_NUM_CHANNELS value > 1 as a trigger for
enabling support for P2P multichannel channel concurrency. This does not
handle all possible details of enforcing driver capabilities, but it is
a good first step for allowing nl80211 drivers to enable multichannel
concurrency.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The driver_test.c data structures had been changed to use a separate
BSS structure, but the P2P commands were not using the new design.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
A new optional delay=<search delay in milliseconds> parameter can now be
used with p2p_find command to request an extra delay between search
iterations. This can be used, e.g., to make p2p_find friendlier to
concurrent operations by avoiding it from taking 100% of the radio
resources.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
CONFIG_VLAN_NETLINK=y build option can now be used to replace the
ioctl()-based interface for creating and removing VLAN interfaces
with netlink-based interface.
Signed-hostap: M. Braun <michael-dev@fami-braun.de>
Commit a11241fa11 removed the 802.11b rate
enabling/disabling code from wpa_driver_nl80211_set_mode() and while
doing that, removed the only place where drv->disabled_11b_rates was
set. Fix this by updating the flag in nl80211_disable_11b_rates(). In
addition, re-enable the 802.11b rates when changing to non-P2P mode.
Signed-hostap: Jouni Malinen <j@w1.fi>
Right now 11b rates are masked out while creating a P2P interface,
but this is always failing as the interface is down. Most drivers
allow to configure rates only when the interface is UP and running.
So let us disable 11b rates when interface type is changed into a
P2P type and it is UP and running.
Signed-hostap: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Couple of functions did not verify that nla_put_nested() succeeded. Fix
these by checking the return value and handling error cases cleanly.
Signed-hostap: Jouni Malinen <j@w1.fi>
This allows the SA Query mechanism in hostapd to be used with drivers
that implement authentication and association MLME/SME.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
disable_dgaf=1 in hostapd.conf can now be used to disable downstream
group-addressed forwarding (DGAF). In this configuration, a unique
GTK (and IGTK) is provided to each STA in the BSS to make sure the
keys do not match and no STA can forge group-addressed frames.
An additional mechanism in the AP needs to be provided to handle some
group-addressed frames, e.g., by converting DHCP packets to unicast
IEEE 802.11 frames regardless of their destination IP address and by
providing Proxy ARP functionality.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Allow the user to configure an RSSI threshold in dBm below which the
nl80211 driver won't report scan results. Currently only supported
during scheduled (PNO) scans.
Signed-off-by: Thomas Pedersen <c_tpeder@qca.qualcomm.com>
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This updates the license notification to use only the BSD license. The
changes were acknowledged by email (Gunter Burchardt, tmisu@gmx.de,
Mon, 02 Jul 2012 17:54:28 +0200).
Signed-hostap: Jouni Malinen <j@w1.fi>
This updates the license notification to use only the BSD license. The
changes were acknowledged by email (Jouke Witteveen
<j.witteveen@gmail.com>, Mon, 2 Jul 2012 11:38:34 +0200).
Signed-hostap: Jouni Malinen <j@w1.fi>
This updates these files to use the license notification that uses only
the BSD license. The changes were acknowledged by email (Sam Leffler
<sam@errno.com>, Sat, 30 Jun 2012 07:57:53 -0700).
Signed-hostap: Jouni Malinen <j@w1.fi>
Some drivers may independently decide to switch channels. Handle this by
updating the hostapd and wpa_supplicant AP and GO configuration.
Signed-hostap: Thomas Pedersen <c_tpeder@qca.qualcomm.com>
The control message received from the kernel needs some space, but
there's no need for the strange typing that breaks clang compilation.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
In certain cases like PBC session overlap it appears to be possible that
an interface is removed due to an event handled on it, this leads to
list corruption. Use safe iteration to prevent this issue.
Reported-by: Nirav Shah <nirav.j2.shah@intel.com>
Reported-by: Neeraj Kumar Garg <neerajkg@broadcom.com>
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
intended-for: hostap-1
When sending an offchannel frame (mainly, P2P Invitation Request), the
wait_time parameter was hardcoded to 0 for drivers that implement AP
mode SME. This is not correct and can cause problems for drivers that
support offloading of off-channel operations with driver/firmware based
AP SME.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This is a workaround for interoperability issues with some deployed P2P
implementations that require a Provision Discovery exchange to be used
before GO Negotiation. The new provdisc parameter for the p2p_connect
command can be used to request this behavior without having to run a
separate p2p_prov_disc command.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The nl80211 driver interface does not allow 128-bit WEP to be used
without a vendor specific cipher suite and no such suite is defined for
this purpose. Do not accept WEP key length 16 for nl80211 driver
interface forn ow. wext-interface can still try to use these for
backwards compatibility.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
An existing persistent group information can now be used to force GO
Negotiation to use the previously used SSID/passphrase from a persistent
group if we become a GO. This can be used as an alternative to inviting
a new P2P peer to join the group (i.e., use GO Negotiation with GO
intent 15 instead of starting an autonomous GO and using invitation),
e.g., in case a GO Negotiation Request is received from a peer while we
are not running as a GO. The persistent group to use for parameters is
indicated with persistent=<network id> parameter to p2p_connect.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
There is no need to subscribe to event messages during deinit process,
so skip this to avoid unnecessary operations and to keep the debug logs
a bit cleaner.
Signed-hostap: Jouni Malinen <j@w1.fi>
This was previously indicated as disassociation, but the P2P group
session ending case expect a deauthentication notification. Since the
cfg80211 disconnection event does not really indicate which frame was
used, the easiest approach for now seems to be to just indicate these
as deauthentication events.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
On P2P group removal, the GO is deinitialized correctly (and the vif
mode is set back to sta in case of nl80211), but the P2P client mode
wasn't deinitialized, and the nl80211 vif stays in P2P client mode.
Add a new deinit_p2p_cli op (similar to deinit_ap), which currently only
sets the interface back to station mode.
Signed-hostap: Eliad Peller <eliad@wizery.com>
intended-for: hostap-1
The signal strength is currently never used as the only driver reporting
it is nl80211 which uses IEEE80211_RADIOTAP_DB_ANTSIGNAL which is never
populated by the kernel. The kernel will (soon) populate
IEEE80211_RADIOTAP_DBM_ANTSIGNAL instead though, so use that.
Also, since it was never really populated, we can redefine the signal
field to be in dBm units only.
My next patch will also require knowing the signal strength of probe
requests throughout the code (where available), so add it to the
necessary APIs.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
A network block specific background scan period can now be configured
for drivers that implement internal background scan mechanism for
roaming and BSS selection.
Signed-hostap: Bala Shanmugam <bkamatch@qca.qualcomm.com>
When drivers advertise their capability to free up inactive
stations based on ap_max_inactivity, send the inactivity period
timeout to driver in NL80211_ATTR_INACTIVITY_TIMEOUT. This
introduces a WPA_DRIVER_FLAGS (WPA_DRIVER_FLAGS_INACTIVITY_TIMER)
so that the inactivity period will be sent only when this capability
bit is set.
Signed-hostap: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
When the driver (or firmware) implements AP mode SME, the use of raw
management frame TX functions is not working properly at the moment. As
an initial step, convert these AP mode operations to use
NL80211_CMD_DEL_STATION and do not claim that driver provides TX status
for deauth/disassoc frames. While this does not address all use cases
(e.g., reason code is not specified in the command), this fixes number
of issues where the station does not get disconnected properly.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Use Device Password ID in WSC IE of Probe Request and Probe Response
frames to advertise immediate availability of WPS credentials per P2P
specification sections 3.1.2.1.1 (Listen State), 3.1.2.1.2 (Scan Phase),
and 3.1.2.1.3 (Find Phase).
For now, the Device Password ID is set only for the case where we are
active GO Negotiation with a specific peer. In practice, this means that
the Probe Response frames during pending GO Negotiation (whenever in
Listen state) indicate availability of the credential.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
It looks like a RTM_NEWLINK event claiming the interface to be UP is
delivered just before removing an interface after having first indicated
that the interface was going down/removed. Ignore this event if the
interface is not present anymore at the moment the event is processed.
This fixes issues where an interface that was re-added after being
removed did not get reconfigured properly.
Signed-hostap: Jouni Malinen <j@w1.fi>
intended-for: hostap-1
It looks like a RTM_NEWLINK event claiming the interface to be UP is
delivered just before removing an interface after having first indicated
that the interface was going down/removed. Ignore this event if the
interface is not present anymore at the moment the event is processed.
This fixes issues where an interface that was re-added after being
removed did not get reconfigured properly.
Signed-hostap: Jouni Malinen <j@w1.fi>
intended-for: hostap-1
Add support to send Action frames to the driver.
Add support for TSPEC req and adding STA node to the driver.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
"wpa_cli set radio_disabled 1/0" can be used to disable/enable
radio to simulate out-of-radio-range condition in a testbed
device.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
In IBSS RSN cfg80211/mac80211 now waits for userspace to authorize new
stations. This patch makes wpa_supplicant notify the driver when a
station can be considered authorized.
Signed-hostap: Antonio Quartulli <ordex@autistici.org>
Remove the GPL notification text from files that were initially
contributed by Atheros Communications or Qualcomm Atheros.
Signed-hostap: Jouni Malinen <j@w1.fi>
This allows HT capabilities overrides on kernels that
support these features.
MCS Rates can be disabled to force to slower speeds when using HT.
Rates cannot be forced higher.
HT can be disabled, forcing an 802.11a/b/g/n station to act like
an 802.11a/b/g station.
HT40 can be disabled.
MAX A-MSDU can be disabled.
A-MPDU Factor and A-MPDU Density can be modified.
Please note that these are suggestions to the kernel. Only mac80211
drivers will work at all. The A-MPDU Factor can only be decreased and
the A-MPDU Density can only be increased currently.
Signed-hostap: Ben Greear <greearb@candelatech.com>
In multiple BSSes scenario for the drivers that do not use
monitor interface and do not implement AP SME, RX MGMT
frame subscription happens only for the default bss (first_bss).
Subscribe for RX MGMT frames for such BSSes.
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Commit e4fb216769 moved frequency
storage from driver struct to bss struct and is assigned in
wpa_driver_nl80211_set_freq. As this wpa_driver_nl80211_set_freq is
triggered only on the first_bss, bss->freq for other BSSes is never
being set to the correct value. This sends MLME frames on frequency zero
(initialized value of freq) for BSSes other than the first.
To fix this derive frequency value from first_bss.
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
When the "bssid=" option is set for an IBSS network and ap_scan = 2,
ask the driver to fix this BSSID, if possible.
Previously, any "bssid=" option were ignored in IBSS mode when ap_scan=2.
Signed-hostap: Nicolas Cavallari <cavallar@lri.fr>
A P2P Action frame may need to be sent on another channel than the GO's
operating channel. This information was lost in
wpa_driver_nl80211_send_action() in the case the interface was in AP
mode. Pass the frequence and related parameters to send_mlme mechanism
to allow the correct frequence to be used with the send frame command in
AP (P2P GO) mode.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The cookie value needs to be fetched in GO mode, too, to be able to
indicate TX status callbacks with drivers that handle AP mode SME
functionality internally. This fixes issues with client discoverability
where TX status callback for GO Discoverability Request is needed to
trigger the GO to send Device Discoverability Response.
dev_id=<P2P Device Addr> can now be specified as an argument to
p2p_find to request P2P find for a specific P2P device.
Signed-hostap: Jouni Malinen <j@w1.fi>
The deauthentication and disassociation events from nl80211 were being
processed identically regardless of whether the frame was generated by
the local STA or the AP. This resulted in fast reconnection mechanism
getting triggered even in the case where the disconnection was detected
locally (e.g., due to beacon loss) while this was supposed to happen
only in the case where the AP is sending an explicit Deauthentication
or Disassociation frame with a specific reason code.
Fix this by adding a new deauth/disassoc event variable to indicate
whether the event was generated locally.
Signed-hostap: Jouni Malinen <j@w1.fi>
The offchanok parameter is hardcoded to one in number of paths and that
added NL80211_ATTR_OFFCHANNEL_TX_OK attribute to NL80211_CMD_FRAME
unconditional. cfg80211 rejects this with EINVAL if the driver does not
indicate support for offchannel TX. Fix this by not requesting
offchannel TX depending on driver capabilities. Remain-on-channel
operation was used for those cases anyway, so the additional attribute
was not really needed for these in the first place.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
When nl80211_setup_ap() has enabled Probe Request reporting, this must
not be disabled when P2P Listen state is stopped to avoid breaking AP
mode operations. This could happen, e.g., if a Probe Request frame was
received from a P2P device that the we are trying to invite to our group
(i.e., when operating in GO role). p2p_probe_req_rx() calls
p2p_invite_start() in this case and that ends up calling
p2p->cfg->stop_listen() which calls probe_req_report() driver op.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Drivers that use device SME in AP mode may still need to be
subscribed for Action frame RX when monitor interface is not used.
This fixes number of P2P GO operations with ath6kl.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Poll command may be enough for mac80211 to figure out whether monitor
interface is to be used, but this change did not take into account
non-mac80211 drivers that support AP mode without monitor interface.
For example, ath6kl needs to get use_monitor disabled.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Android ICS system/core/libnl_2 has very limited genl_ctrl_resolve()
implementation that cannot handle names other than nlctrl. Work
around that by implementing more complete genl_ctrl_resolve()
functionality within driver_nl80211.c for Android builds.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
I needed this patch to compile against the latest
libnl code. I added this to my config file:
CONFIG_LIBNL32=y
Signed-hostap: Ben Greear <greearb@candelatech.com>
This updates a previous patch did more or less the same thing by
providing the qosinfo as a single variable to the driver wrappers.
Signed-hostap: Jason Young <jason.young@dspg.com>
Add uapsd_queues and max_sp fields to sta_info struct,
and pass them to the sta_add callback.
These values are determined by the WMM IE in the (Re)Association Request.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Check whether the driver advertises support for U-APSD
in AP mode, and evaluate wmm_uapsd only in this case.
Signed-off-by: Eliad Peller <eliad@wizery.com>
The wpa_hexdump_ascii() call did not get converted properly and this
was missed becaused of it getting defined out from the build. Anyway,
this better use the correct variable names should that debug print
ever be enabled for Android.
Signed-hostap: Jouni Malinen <j@w1.fi>
Pass the raw Probe Response template to kernel via netlink using the
set_ap() driver callback. The data is sent as one of the Beacon
attributes.
Signed-hostap: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Configure a Probe Response template for drivers that support it. The
template is updated when the Beacon template is updated.
The Probe Response template is propagated to the driver via the set_ap()
callback.
Signed-hostap: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Translate nl80211 flags to wpa_supplicant flags for Probe Response
offload support. The existence of the nl80211 PROBE_RESP_OFFLOAD_SUPPORT
attribute means Probe Response offload is supported. The value of the
attribute is a bitmap of supported protocols.
Signed-hostap: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Storing the address in the BSS instead of the DRV struct makes it usable
for hostapd and thus gets rid of the linux_get_ifhwaddr() call when
receiving a spurious frame.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
If Provision Discovery Request is sent for GO role (i.e., P2P Group ID
attribute is included), add the group interface name to the control
interface event on the GO. This makes it easier to figure out which
ctrl_iface needs to be used for wps_pbc/wps_pin command to authorize
the joining P2P client.
Signed-hostap: Jouni Malinen <j@w1.fi>
This can be used to request Provision Discovery Request to be sent
for the purpose of joining a running group, e.g., to request the GO
to display a PIN that we can then use with p2p_connect join command.
Signed-hostap: Jithu Jance <jithu@broadcom.com>
Since the nl_cache is not used anymore, there is no need for maintaining
the struct nl80211_handles wrapper for struct nl_handle. Clean this up
by using nl_handle directly.
Signed-hostap: Jouni Malinen <j@w1.fi>
This is a rewrite of Ben Greear's patch, making the
nl80211 code use just a single multicast event socket.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
When running AP mode, we need to receive beacons over overlapping BSSes
to handle protection. Use the new nl80211 command for this. As the
command works per wiphy (and we don't want to receive the Beacon frames
multiple times) add an abstraction that keeps track of per-wiphy data.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
These events are necessary to send deauth frames to
stations sending spurious data frames. Subscribe to
them on the per-BSS event socket.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
To achieve this, multiple things are needed:
1) since hostapd needs to handle *all* action frames,
make the normal registration only when in a non-AP
mode, to be able to do this use the new socket
2) store the frequency in each BSS to be able to give
the right frequency to nl80211's mgmt-tx operation
3) make TX status processing reject non-matched cookie
only in non-AP mode
The whole thing depends on having station-poll support
in the kernel. That's currently a good indicator since
the kernel patches are added together.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
When using authentication retry within driver_nl80211.c, a failure on the
second attempt has to be indicated with a driver event since the return
code from wpa_driver_nl80211_authenticate() is not actually delivered to
the core code in that case.
Signed-hostap: Jouni Malinen <j@w1.fi>
cfg80211 rejects NL80211_CMD_AUTHENTICATE with ENOENT if the BSS entry
for the target BSS is not available. This can happen if the cfg80211
entry has expired before wpa_supplicant entry (e.g., during a suspend).
To recover from this quickly, run a single channel scan to get the
cfg80211 entry back and then retry authentication command again. This
is handled within driver_nl80211.c to keep the core wpa_supplicant
implementation cleaner.
Signed-hostap: Jouni Malinen <j@w1.fi>
Set the NL80211_ATTR_CONTROL_PORT_NO_ENCRYPT flag for nl80211 to tell
drivers (mac80211) to not encrypt the EAPOL frames for WEP IEEE 802.1X.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
In preparation for things that receive on a BSS-specific handle,
allocate a CB for it and hook it up to receive functions.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
The next patch will add process_bss_event, rename process_event to
process_drv_event to differentiate between them.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
By passing the nl_cb as the context to the eloop function we can
(in the next patch) use the same eloop function for BSS events.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
Storing the frequency in the bss struct allows using it for frame
commands in AP mode and not relying on the driver struct as much, which
is good for hostapd mode.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
This will allow getting TX status for EAPOL frames
sent as data frames if the driver supports it.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
The RTM_NEWLINK even can have IFF_UP flag even if the interface is
down. Do not generate EVENT_INTERFACE_ENABLED event based on such a
message.
Signed-hostap: Jouni Malinen <j@w1.fi>
This is based on the Android driver_cmd changes that are converted to
use the sched_scan/stop_sched_scan driver_ops for the case where the
driver does not support the new nl80211 commands.
Change-Id: Iaedc340f84650af422bd2ea57d2a8b0a9d4a5330
Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
(jm: This is based on the Android change that used driver_cmd. The same
implementation is used for the actual driver interface, but the commands
are now accessed through sched_scan/stop_sched_scan driver_ops instead
of driver_cmd)
IW_ENCODE_ALG_PMK and IW_ENC_CAPA_4WAY_HANDSHAKE are not defined in the
Android tree, so add compatibility defines for these.
Signed-hostap: Jouni Malinen <j@w1.fi>
cfg80211 will reject the NL80211_CMD_START_SCHED_SCAN if too many
match sets are requested. To avoid being completely unable to start
any scheduled scans, skip setting these filters if the driver did
not advertise support for large enough number of match sets.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This adds initial implementation of set_p2p_powersave to allow legacy PS
mode to be configured. P2P PS parameters are not yet supported.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
It's not really valid to send off-channel in all cases,
so pass whether it should be allowed or not and don't
set it in the AP case.
Also, to get the right ifindex for hostapd, pass a bss
pointer instead of the drv pointer.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
In some situations it might be benefical to send a unicast frame without
the need for getting it ACKed (probe responses for example). In order to
achieve this add a new noack parameter to the drivers send_mlme callback
that can be used to advise the driver to not wait for an ACK for this
frame.
Signed-hostap: Helmut Schaa <helmut.schaa@googlemail.com>
If the kernel supports this, don't use manual null
data frame transmissions. This is one thing to get
rid of cooked monitor interfaces.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
The non-monitor TX currently uses a normal L2 abstraction
socket, but that will also receive frames we don't want,
so use a plain socket that isn't bound for RX. This might
be possible using the L2 abstraction, but we need a plain
socket later for getting TX status events here.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
This changes the auto-detection of whether or not the device contains
the AP SME away from monitor interface addition failing to the explicit
attribute in nl80211. Keep the old auto-detection for a little while so
that ath6kl isn't broken right away.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
The new event can be used when EAPOL TX status can't be reported as a
complete 802.11 frame but is instead reported as just the EAPOL data as
originally passed to hapd_send_eapol().
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
This patch implements shared_freq handler for driver_nl80211.c. If a
"p2p_group_add" happens after legacy STA association, then this patch
will help to start the GO on the same frequency. This is useful when
supplicant is started on multiple interface running over a singly "PHY"
and the station interface is not used for the P2P device operations.
For example, wpa_supplicant -iwlan0 .. -N -iwlan1 ... and wlan0 is used
for station connection and wlan1 as the P2P device interface.
Signed-hostap: Jithu Jance <jithu@broadcom.com>
Without this, it is impossible to tell exactly which
MLME code returned the error.
Also, convert to wpa_dbg so that we get device names
in the messages.
Signed-hostap: Ben Greear <greearb@candelatech.com>
All we really need is the family ID, and we can
get that with genl_ctrl_resolve() and then don't
need to worry about family/cache objects.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
WEXT is not really changing anymore and more or less all Linux
distros come with linux/wireless.h that is recent enough to
allow the driver wrappers to be build.
Signed-hostap: Jouni Malinen <j@w1.fi>
This has been obsoleted by the more generic Linux WEXT (driver_wext.c)
support. The hostap and madwifi driver wrappers can now be used only
with hostapd. The old station interface remains available in releases up
to 1.x.
Signed-hostap: Jouni Malinen <j@w1.fi>
The driver wrappers broadcom, iphone, osx, and ralink have not been
maintained for a while and it does not look like they will be in the
future either. As such, remove them from the development branch. The
previous versions will be included in older releases up to 1.x.
Signed-hostap: Jouni Malinen <j@w1.fi>
Use a driver_ndis.c specific initialization function to fill in the
wpa_driver_ops information to make it easier to modify struct
wpa_driver_ops in the future. Being able to build driver_ndis.c
with MSVC was the only reason for having to maintain the same order
of function pointers in struct wpa_driver_ops and for having to
update driver_ndis.c for all changes in that structure.
Signed-hostap: Jouni Malinen <j@w1.fi>
In scan.c, merge a channel's noise value into the scan results. When
comparing scan results, compute the signal-to-noise ratio and use it
when available. Prefer a 5 GHz network if its SNR is really big (> 30)
or if its SNR is relatively close to the other network's.
Instead of hardcoding IEEE 802.11b rates to be disabled whenever
P2P support is built in and supported by the driver, do this only
when an interface is set to P2P mode (both when adding a new
interface and when changing the interface mode). This re-enables
use of IEEE 802.11b APs with CONFIG_P2P=y builds.
Signed-hostap: Jouni Malinen <j@w1.fi>
This function was used unconditionally if wpa_supplicant build
includes CONFIG_P2P=y. Adding a separate driver_ops for such use
is not really useful since the driver wrappers can do the same
internally. Remove this driver_ops and move matching functionality
into driver_nl80211.c which was the only driver wrapper using
this driver_ops callback.
Signed-hostap: Jouni Malinen <j@w1.fi>
nl80211_disable_11b_rates() function was supposed to use the 'disabled'
parameter to figure out whether to disable or re-enable 802.11b rates.
In addition, the driver deinit path was now ending up re-disabling the
enabled rates at the end of the deinit operations when the interface
type was forced back to station. Both of these issues are now fixed
and the 2.4 GHz band TX rate index is cleared properly when
wpa_supplicant is stopped.
Signed-hostap: Jouni Malinen <j@w1.fi>
disable_11b_rates() is called on interface addition,
but not on interface type change, resulting in 11b rates
enabled on p2p interfaces.
Signed-off-by: Eliad Peller <eliad@wizery.com>
This can be used to apply the no-CCK rule conditionally depending on
which frame is being sent. The no-CCK rule applies only for P2P
management frames while SA Query and FT use cases do not have similar
restrictions.
Signed-hostap: Jouni Malinen <j@w1.fi>
Add a new attribute to specify whether to use CCK rate or not during
scan and sending management frames. This helps to send P2P probes
at non-CCK rate. This ensures that P2P probe request/response/action
frames are always sent at non-CCK rates.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
The netlink event processing is delayed since they are only returned
after control returns to eloop. This can result in netlink down events
being processed at a point when the interface has is actually still
there (the first event on new interface is down) and that can result in
odd behavior especially when the resulting interface-disabled event is
delivered to AP mode interface with wpa_supplicant.
Work around this by filtering netlink down events if the matching
interface is up at the time the netlink event is processed. This fixes
an issue brought up by commit 36d84860bb.
Before commencing setup, add a new STA entry to the driver representing
the peer. Later during setup, update the STA entry using information
received from the peer.
Extend sta_add() callback for adding/modifying a TDLS peer entry and
connect it to the TDLS state machine. Implement this callback for the
nl80211 driver and send peer information to kernel.
Mark TDLS peer entries with a new flag and translate it to a
corresponding nl80211 flag in the nl80211 driver.
In addition, correct TDLS related documentation in the wpa_driver_ops
structure.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Cc: Kalyan C Gaddam <chakkal@iit.edu>
Register for the TDLS discovery response public action frame in nl80211.
Print out a debug message when a Discovery Resp frame is received and
validated.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Cc: Kalyan C Gaddam <chakkal@iit.edu>
Allow passing high-level TDLS commands and TDLS frames to kernel
via new nl80211 commands.
Propagate TDLS related nl80211 capability flags from kernel and add them
as driver capability flags.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Cc: Kalyan C Gaddam <chakkal@iit.edu>
This function is actually needed for quite a bit more than just
user space MLME implementation. The old comment here has not been
accurate for a long time, so get rid of it.
These driver_ops functions set_channel, set_ssid, set_bssid,
mlme_add_sta, and mlme_remove_sta were used with the user space
MLME implementation in wpa_supplicant. That was only for testing
purposes and was removed, but these driver_ops were forgotten.
Remove them now to remove confusing driver_ops definitions.
This code was used only with driver_test.c to allow MLME operations
in hostapd to be tested without having to use a real radio. There
are no plans on extending this to any other use than testing and
mac80211_hwsim has now obsoled the need for this type of testing.
As such, we can drop this code from wpa_supplicant to clean up the
implementation of unnecessary complexity.
Netlink sockets can be shared among all driver instances, saving lots
of sockets, spurious log messages, memory, and CPU usage when using
multiple interfaces in a single process.
This offloads the station polling to driver wrappers, which may offload
it again to the driver. The hostap driver wrapper uses "real" data
frames while nl80211 uses null data frames.
Also add a specific event to indicate that a poll was successful for
future use with the nl80211 driver.
Some dualband cards can use more than five seconds to run through
a full scan, so increase the timeout to avoid hitting the missing
scan completed event workaround.
Remove the separate driver_ops functions set_cts_protect(),
set_preamble(), set_short_slot_time(), and set_ht_params(). These
belong into same set of operations as set_ap(), so there is no need
to maintain separate functions that just make the driver wrapper
more complex.
Since these have only been used with driver_nl80211.c, the driver_ops
can be removed immediately instead of maintaining backwards
compatibility period with the old functions.
The AP client isolation parameter is now available through set_ap().
driver_nl80211.c was the only driver wrapper using the set_intra_bss()
call in hostap.git, but some external trees may have used this. Once
those are cleared, the set_infra_bss() driver_ops can be removed
completely. The only remaining use case for it currently is in P2P
GO mode with wpa_supplicant.
