This adds a wifi_generation=4/5/6 line to the STATUS output if the
driver reports (Re)Association Request frame and (Re)Association
Response frame information elements in the association or connection
event. Only the generations 4 (HT = 802.11n), 5 (VHT = 802.11ac), and 6
(HE = 802.11ax) are reported.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Extend wpa_psk_file to allow an optional VLAN ID to be specified with
"vlanid=<VLAN ID>" prefix on the line. If VLAN ID is specified and the
particular wpa_psk_file entry is used for a station, that station is
bound to the specified VLAN. This can be used to operate a single
WPA2-Personal BSS with multiple VLANs based on the used passphrase/PSK.
This is similar to the WPA2-Enterprise case where the RADIUS server can
assign stations to different VLANs.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This makes the debug log cleaner by removing the mostly confusing prints
about HT override parameters if they are not actually used.
Signed-off-by: Jouni Malinen <j@w1.fi>
This buffer may be used to store items like passwords, so better clean
it explicitly to avoid possibility of leaving such items in heap memory
unnecessarily.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The previous implementation assumed the first entry coming out from the
dict is always service_type. That may not be the case, so properly
iterate over all dict entries in one loop instead of assuming what the
first entry is.
Signed-off-by: Jouni Malinen <j@w1.fi>
If the DPP_LISTEN command failed due to the driver rejecting the
remain-on-channel request, wpa_s->dpp_listen_freq was left set to the
requested listen frequency and this resulted in the next DPP_LISTEN for
the same frequency reporting "DPP: Already listening on .." even when
the driver was not really listening on that frequency. Fix this by
clearing wpa_s->dpp_listen_freq in the error case.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The avoid channels are notified through
QCA_NL80211_VENDOR_SUBCMD_AVOID_FREQUENCY allow minimal traffic, so
enhance the P2P behavior accordingly by considering these avoid
frequencies for P2P discovery/negotiation as long as they are not in
disallowed frequencies list.
Additionally, do not return failure when none of social channels are
available as operation channel, rather, mark the op_channel/op_reg_class
to 0 as this would anyway get selected during the group formation in
p2p_prepare_channel.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The network configration option multi_ap_backhaul_sta was added without
adding it to wpa_config_write_network(). Hence the value of this option
was not included when writing the configuration file. Fix this by
including it in wpa_config_write_network().
Fixes: 5abc7823b ("wpa_supplicant: Add Multi-AP backhaul STA support")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This is probably not ideal, since it would be better if it ended up
being autogenerated somehow, but at least it's somewhat of an
improvement.
Also added a comment that encourages keeping the docs in sync.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
When setting scan with randomized MAC, check the requested scan type
against supported types, to ensure callers will not set an unsupported
type, since this can cause scan/connect failures later. It is better to
do this in wpas_mac_addr_rand_scan_set() instead of control interface
specific code to apply the constraint on all possible interfaces using
this setting.
Signed-off-by: Lior David <liord@codeaurora.org>
sme_event_unprot_disconnect() is only defined with CONFIG_IEEE80211W, so
the CONFIG_TESTING_OPTIONS command UNPROT_DEAUTH can be defined only
with builds that enable IEEE 802.11w support.
Signed-off-by: Lior David <liord@codeaurora.org>
The standard amendment has been published and there has been sufficient
amount of interoperability testing for FILS to expect the protocol not
to be changed anymore, so remove the notes claiming this to be
experimental and not suitable for production use.
Signed-off-by: Jouni Malinen <j@w1.fi>
This reverts commit 2564184440.
Commit 2564184440 ("mesh: Apply channel attributes before setup
interface") triggers some channel configurations to result in leaking
memory. This seems to be caused by hapd->started not getting set when
going through a callback to start hostapd operation (e.g., when using
HT40 coex scan) due to hostapd_setup_bss() not getting called. This
results in hostapd_free_hapd_data() not clearing allocated
hapd->wpa_auth. This can be reproduced with the hwsim test case
mesh_secure_ocv_mix_legacy.
A more complete cleanup of the pending mesh patch for DFS support seems
to be needed to fix this properly, so the best approach for now is to
revert this patch and bring it back once rest of the mesh changes are
ready to be applied.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
If we call p2p_flush from ctrl_iface, before calling p2p_flush() it
calls wpas_p2p_stop_find(). Add the same call to the matching D-Bus
method to clear all pending operations.
Signed-off-by: Amit Khatri <amit7861234@gmail.com>
To enhance privacy, generate a random interface for each group.
There are two configurations are introduced:
* p2p_interface_random_mac_addr
enable interface random MAC address feature, default disable.
Signed-off-by: Jimmy Chen <jimmycmchen@google.com>
To enhance privacy, generate a random device address for P2P interface.
If there is no saved persistent group, it generate a new random MAC
address on bringing up p2p0. If there is saved persistent group, it will
use last MAC address to avoid breaking group reinvoke behavior.
There are two configurations are introduced:
* p2p_device_random_mac_addr
enable device random MAC address feature, default disable.
* p2p_device_persistent_mac_addr
store last used random MAC address.
Signed-off-by: Jimmy Chen <jimmycmchen@google.com>
An optional parameter "he" is added to p2p_connect, p2p_group_add, and
p2p_invite to enable 11ax HE support. The new p2p_go_he=1 configuration
parameter can be used to request this to be enabled by default.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Start the (EAP request) identifier at an initial random value
as recommended by RFC 3748 in section 4.1 Request and Response
on page 21.
Signed-off-by: Martin Stanislav <ms@uakom.sk>
Upon issuing a connect request we need to indicate that we want the
driver to offload the 802.1X 4-way handshake for us. Indicate it if
the driver capability supports the offload.
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Allow drivers to indicate support for offloading 4-way handshake for
either IEEE 802.1X (WPA2-Enterprise; EAP) and/or WPA/WPA2-PSK
(WPA2-Personal) by splitting the WPA_DRIVER_FLAGS_4WAY_HANDSHAKE flag
into two separate flags.
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
If a station is configured to allow only a subset of frequencies for an
association, the supported operating classes may need to be more limited
than what the hardware supports.
Signed-off-by: Ben Greear <greearb@candelatech.com>
If user has disabled HT or VHT, those related operating classes
should not be advertised as supported.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Mesh in VHT mode is supposed to be able to use any bandwidth that VHT
supports, but there was no way to set VHT20 although there are
parameters that are supposed to be used. This commit along then previous
commit for VHT_CHANWIDTH_USE_HT makes mesh configuration available to
use any bandwidth with combinations of existing parameters like shown
below.
VHT80:
default
do not set any parameters
VHT40:
max_oper_chwidth = 0
VHT20:
max_oper_chwidth = 0
disable_ht40 = 1
HT40:
disable_vht = 1
HT20:
disable_ht40 = 1
disable HT:
disable_ht = 1
Signed-off-by: Peter Oh <peter.oh@bowerswilkins.com>
Channel width in VHT mode refers HT capability when the width goes down
to below 80 MHz, hence add checking HT channel width to its max
operation channel width. So that mesh has capability to select bandwidth
below 80 MHz.
Signed-off-by: Peter Oh <peter.oh@bowerswilkins.com>
This provides similar features to what was already available for HT
overrides. Probe Request frames look correct, and VHT capabilities shown
in debugfs look as expected.
Signed-off-by: Ben Greear <greearb@candelatech.com>
There is no need to allow symlink dereferencing in these cases where a
file (including directories and sockets) are created by the same
process, so use the safer lchown() variant to avoid leaving potential
windows for something external to replace the file before the chown()
call. The particular locations used here should not have write
permissions enabled for processes with less privileges, so this may not
be needed, but anyway, it is better to make these more restrictive
should there be cases where directory permissions are not as expected
for a good deployment.
Signed-off-by: Jouni Malinen <j@w1.fi>
wpa_s->bss_tm_status is within #ifdef CONFIG_WNM, so need to access it
through matching condition.
Fixes: 80d06d0ca9 ("dbus: Export BSS Transition Management status")
Signed-off-by: Jouni Malinen <j@w1.fi>
Some distributions (e.g., Debian) have started introducting systemwide
OpenSSL policies to disable older protocol versions and ciphers
throughout all programs using OpenSSL. This can result in significant
number of interoperability issues with deployed EAP implementations.
Allow explicit wpa_supplicant (EAP peer) and hostapd (EAP server)
parameters to be used to request systemwide policies to be overridden if
older versions are needed to be able to interoperate with devices that
cannot be updated to support the newer protocol versions or keys. The
default behavior is not changed here, i.e., the systemwide policies will
be followed if no explicit override configuration is used. The overrides
should be used only if really needed since they can result in reduced
security.
In wpa_supplicant, tls_disable_tlsv1_?=0 value in the phase1 network
profile parameter can be used to explicitly enable TLS versions that are
disabled in the systemwide configuration. For example,
phase1="tls_disable_tlsv1_0=0 tls_disable_tlsv1_1=0" would request TLS
v1.0 and TLS v1.1 to be enabled even if the systemwide policy enforces
TLS v1.2 as the minimum version. Similarly, openssl_ciphers parameter
can be used to override systemwide policy, e.g., with
openssl_ciphers="DEFAULT@SECLEVEL=1" to drop from security level 2 to 1
in Debian to allow shorter keys to be used.
In hostapd, tls_flags parameter can be used to configure similar
options. E.g., tls_flags=[ENABLE-TLSv1.0][ENABLE-TLSv1.1]
Signed-off-by: Jouni Malinen <j@w1.fi>
There is no point in going through FT authentication if the next step
would have to use association exchange which will be rejected by the AP
for FT, so only allow FT-over-air if previous BSSID is set, i.e., if
reassociation can be used.
Signed-off-by: Jouni Malinen <j@w1.fi>
During P2PS PD Request processing wpa_supplicant removes stale and empty
persistent groups, but it did not notify D-Bus to unregister object. Fix
this by adding the missing notifications.
Signed-off-by: Jouni Malinen <j@w1.fi>
During P2PS PD Request processing wpa_supplicant removes stale
persistent groups, but it did not notify D-Bus to unregister object.
This can result in leaving behind objects pointing to freed memory and
memory leaks. Sometime it can cause a crash in wpa_config_get_all()
function and DBUS_ERROR_OBJECT_PATH_IN_USE errors.
Fix this by adding the missed notification to D-Bus code to unregister
the object.
Signed-off-by: Amit Khatri <amit7861234@gmail.com>
Once mesh starts supporting DFS channels, it has to handle DFS related
events from drivers, hence add mesh interface to the check list.
Signed-off-by: Peter Oh <peter.oh@bowerswilkins.com>
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
wpa_supplicant configuration has country parameter that is supposed to
be used in AP mode to indicate supporting IEEE 802.11h and 802.11d.
Reflect this configuration to Mesh also since Mesh is required to
support 802.11h and 802.11d to use DFS channels.
Signed-off-by: Peter Oh <peter.oh@bowerswilkins.com>
RSN initialization should work together with mesh join when it's used.
Since mesh join could be called at a different stage if DFS channel is
used, relocate the RSN initialization call to mesh join. It is still the
same call flow of mesh join before this if non-DFS channels are used,
hence no significant side effect will occur.
Signed-off-by: Peter Oh <peter.oh@bowerswilkins.com>
Mesh join function consists of two parts which are preparing
configurations and sending join event to the driver. Since physical mesh
join event could happen either right after mesh configuration is done or
after CAC is done in case of DFS channel is used, factor out the
function into two parts to reduce redundant calls.
Signed-off-by: Peter Oh <peter.oh@bowerswilkins.com>
RSN initialization can be used in different phases if mesh
initialization and mesh join don't happen in sequence such as DFS CAC is
done in between, hence factor it out to help convering the case. This
can also get rid of unnecessary indentation by handling the
mconf->security != MESH_CONF_SEC_NONE functionality in a helper
function.
Signed-off-by: Peter Oh <peter.oh@bowerswilkins.com>
Setting mem_only_psk=1 in the wpa_supplicant configuration prevents the
passphrase from being stored in the configuration file. wpa_supplicant
will request the PSK passphrase over the control interface in such case
and this new wpa_cli command can be used to set the psk_passphrase.
usage:
psk_passphrase <network id> <psk_passphrase>
Signed-off-by: Hagai Moshe <hagai.moshe@tandemg.com>
Signed-off-by: Simon Dinkin <simon.dinkin@tandemg.com>
wpa_supplicant currently logs CTRL-EVENT-AUTH-FAILED errors when
authentication fails, but doesn't expose any property to the D-Bus
interface related to this.
This change adds the "AuthStatusCode" property to the interface, which
contains the IEEE 802.11 status code of the last authentication.
Signed-off-by: Alex Khouderchah <akhouderchah@chromium.org>
Add new Interface properties "BSSTMStatus", which carries the status of
the most recent BSS Transition Management request. This property will be
logged in UMA to measure 802.11v success.
Signed-off-by: Matthew Wang <matthewmwang@chromium.org>
Add new Interface properties "RoamTime", "RoamComplete", and
"SessionLength". "RoamTime" carries the roam time of the most recent
roam in milliseconds. "RoamComplete" carries True or False corresponding
to the success status of the most recent roam. "SessionLength" carries
the number of milliseconds corresponding to how long the connection to
the last AP was before a roam or disconnect happened.
Signed-off-by: Matthew Wang <matthewmwang@chromium.org>
The new ieee802_11_ext_capab() and wpa_bss_ext_capab() functions can be
used to check whether a specific extended capability bit is set instead
of having to implement bit parsing separately for each need.
Signed-off-by: Jouni Malinen <j@w1.fi>
These flags were used in SCAN_RESULTS command output, but not BSS. Make
these consistent by adding the flags to BSS as well.
Signed-off-by: Jouni Malinen <j@w1.fi>
