This adds a wifi_generation=4/5/6 line to the STATUS output if the
driver reports (Re)Association Request frame and (Re)Association
Response frame information elements in the association or connection
event. Only the generations 4 (HT = 802.11n), 5 (VHT = 802.11ac), and 6
(HE = 802.11ax) are reported.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
An optional parameter "he" is added to p2p_connect, p2p_group_add, and
p2p_invite to enable 11ax HE support. The new p2p_go_he=1 configuration
parameter can be used to request this to be enabled by default.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
If user has disabled HT or VHT, those related operating classes
should not be advertised as supported.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Mesh join function consists of two parts which are preparing
configurations and sending join event to the driver. Since physical mesh
join event could happen either right after mesh configuration is done or
after CAC is done in case of DFS channel is used, factor out the
function into two parts to reduce redundant calls.
Signed-off-by: Peter Oh <peter.oh@bowerswilkins.com>
wpa_supplicant currently logs CTRL-EVENT-AUTH-FAILED errors when
authentication fails, but doesn't expose any property to the D-Bus
interface related to this.
This change adds the "AuthStatusCode" property to the interface, which
contains the IEEE 802.11 status code of the last authentication.
Signed-off-by: Alex Khouderchah <akhouderchah@chromium.org>
Add new Interface properties "BSSTMStatus", which carries the status of
the most recent BSS Transition Management request. This property will be
logged in UMA to measure 802.11v success.
Signed-off-by: Matthew Wang <matthewmwang@chromium.org>
Add new Interface properties "RoamTime", "RoamComplete", and
"SessionLength". "RoamTime" carries the roam time of the most recent
roam in milliseconds. "RoamComplete" carries True or False corresponding
to the success status of the most recent roam. "SessionLength" carries
the number of milliseconds corresponding to how long the connection to
the last AP was before a roam or disconnect happened.
Signed-off-by: Matthew Wang <matthewmwang@chromium.org>
IEEE P802.11-REVmd/D2.0, 9.4.2.20.7 (Beacon request) and 9.4.2.21.7
(Beacon report) add the Last Beacon Report Indication subelement to
Beacon Request and Beacon Report elements.
Add the Last Beacon Report Indication subelement to all Beacon Report
elements if the Beacon Request indicated that this subelement is
requested.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
An AP might refuse to connect a STA if it has a low RSSI. In such case,
the AP informs the STA with the desired RSSI delta and a retry timeout.
Any subsequent association attempt with that AP (BSS) should be avoided,
unless the RSSI level improved by the desired delta or the timeout has
expired.
Defined in Wi-Fi Alliance Optimized Connectivity Experience technical
specification v1.0, section 3.14 (RSSI-based association rejection
information).
Signed-off-by: Beni Lev <beni.lev@intel.com>
Try to make sure the driver channel list state is synchronized with
wpa_supplicant whenever explicitly clearing state (e.g., between hwsim
test cases).
Signed-off-by: Jouni Malinen <j@w1.fi>
Indicate whether the driver advertises support for Multi-BSS STA
functionality with "GET_CAPABILITY multibss" (returns "MULTIBSS-STA" if
supported).
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Advertise vendor specific Multi-AP IE in (Re)Association Request frames
and process Multi-AP IE from (Re)Association Response frames if the user
enables Multi-AP fuctionality. If the (Re)Association Response frame
does not contain the Multi-AP IE, disassociate.
This adds a new configuration parameter 'multi_ap_backhaul_sta' to
enable/disable Multi-AP functionality.
Enable 4-address mode after association (if the Association Response
frame contains the Multi-AP IE). Also enable the bridge in that case.
This is necessary because wpa_supplicant only enables the bridge in
wpa_drv_if_add(), which only gets called when an interface is added
through the control interface, not when it is configured from the
command line.
Signed-off-by: Venkateswara Naralasetty <vnaralas@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Add support for negotiating WNM Collocated Interference Reporting. This
allows hostapd to request associated STAs to report their collocated
interference information and wpa_supplicant to process such request and
reporting. The actual values (Collocated Interference Report Elements)
are out of scope of hostapd and wpa_supplicant, i.e., external
components are expected to generated and process these.
For hostapd/AP, this mechanism is enabled by setting
coloc_intf_reporting=1 in configuration. STAs are requested to perform
reporting with "COLOC_INTF_REQ <addr> <Automatic Report Enabled> <Report
Timeout>" control interface command. The received reports are indicated
as control interface events "COLOC-INTF-REPORT <addr> <dialog token>
<hexdump of report elements>".
For wpa_supplicant/STA, this mechanism is enabled by setting
coloc_intf_reporting=1 in configuration and setting Collocated
Interference Report Elements as a hexdump with "SET coloc_intf_elems
<hexdump>" control interface command. The hexdump can contain one or
more Collocated Interference Report Elements (each including the
information element header). For additional testing purposes, received
requests are reported with "COLOC-INTF-REQ <dialog token> <automatic
report enabled> <report timeout>" control interface events and
unsolicited reports can be sent with "COLOC_INTF_REPORT <hexdump>".
This commit adds support for reporting changes in the collocated
interference (Automatic Report Enabled == 1 and partial 3), but not for
periodic reports (2 and other part of 3).
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Start scans more quickly if an open BSS advertising OWE transition mode
is found, but the matching OWE BSS has not yet been seen.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This commit introduces a threshold for OWE transition BSS selection,
which signifies the maximum number of selection attempts (scans) done
for finding OWE BSS.
This aims to do more scan attempts for OWE BSS and eventually select the
open BSS if the selection/scan attempts for OWE BSS exceed the
configured threshold.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
If the RADIUS authentication server dropped the cached ERP keys for any
reason, FILS authentication attempts with ERP fails and the previous
wpa_supplicant implementation ended up trying to use the same keys for
all consecutive attempts as well. This did not allow recovery from state
mismatch between the ERP server and peer using full EAP authentication.
Address this by trying to use full (non-FILS) authentication when trying
to connect to an AP using the same ERP realm with FILS-enabled network
profile if the previous authentication attempt had failed. This allows
new ERP keys to be established and FILS authentication to be used again
for the consecutive connections.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Timeout is increased by dfs_cac_ms from channel data, or by max CAC time
(10 minutes) if dfs_cac_ms is not defined. This is needed for some more
complex cases, e.g., when STA is acting as an active slave with DFS
offload enabled and decided to start CAC after receiving CONNECT
command, in such a case the 10 second timeout is too small and
wpa_supplicant need to wait for CAC completion or CAC timeout (up to 10
minutes).
Without such timeout modification wpa_supplicant will be unable to
connect to an AP on DFS channel, since the default authentication
timeout (10 s) is smaller than the minimum CAC time (60 s).
Tested with nl80211 DFS offload implementation.
Signed-off-by: Dmitry Lebed <dlebed@quantenna.com>
If any of the interfaces supports FILS (and similarly for FILS-SK-PFS),
include the "fils" (and "fils_sk_pfs") capability in D-Bus information.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
If a DPP_STOP_LISTEN call happens to be received when there is a pending
gas-query radio work that has not yet been started, it was possible for
gas_query_stop() to go through gas_query_done() processing with
gas->work == NULL and that ended up with the pending GAS query getting
freed without removing the pending radio work that hold a reference to
the now freed memory. Fix this by removing the pending non-started radio
work for the GAS query in this specific corner case.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Extend the SME functionality to support the external authentication.
External authentication may be used by the drivers that do not define
separate commands for authentication and association
(~WPA_DRIVER_FLAGS_SME) but rely on wpa_supplicant's SME for the
authentication.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
If a specific DH group for OWE is not set with the owe_group parameter,
try all supported DH groups (currently 19, 20, 21) one by one if the AP
keeps rejecting groups with the status code 77.
Signed-off-by: Jouni Malinen <j@w1.fi>
The new disable_fils parameter can be used to disable FILS functionality
in the driver. This is currently removing the FILS Capability bit in
Extended Capabilities and providing a callback to the driver wrappers.
driver_nl80211.c implements this using a QCA vendor specific command for
now.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Previous implementation did not handle number of sequences correctly.
Make sure the iteration continues in both unicast and broadcast cases
until the five attempts have been made. In addition, improve timing by
checking 10 second time from the beginning of each iteration round and
not the last channel on which the Auth Req frame has been transmitted.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This extends wpa_supplicant DPP implementation to retransmit DPP
Authentication Response frame every 10 seconds up to 5 times if the peer
does not reply with DPP Authentication Confirm frame.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This extends wpa_supplicant to iterate over all available channels from
the intersection of what the peer indicates and the local device
supports when initiating DPP Authentication. In addition, retry DPP
Authentication Request frame up to five times if no response is
received.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This commit introduces the ACS functionality for the autonomous GO. The
optional parameter <freq> in p2p_group_add is enhanced to carry a value
"acs" with the intention to select the channels among any supported
band. freq = 2 / 5 carry the need to select the channels only in the
respective bands 2.4 / 5 GHz. This functionality is on top of the host
driver's capability to offload ACS, which is advertized through
WPA_DRIVER_FLAGS_ACS_OFFLOAD.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The new wpa_supplicant RESEND_ASSOC command can be used to request the
last (Re)Association Request frame to be sent to the AP to test FT
protocol behavior.
This functionality is for testing purposes and included only in builds
with CONFIG_TESTING_OPTIONS=y.
Signed-off-by: Jouni Malinen <j@w1.fi>
This can be used to test replay protection. The "RESET_PN" command in
wpa_supplicant and "RESET_PN <addr>" command in hostapd resets the local
counters to zero for the last configured key. For hostapd, the address
parameter specifies which STA this operation is for or selects GTK
("ff:ff:ff:ff:ff:ff") or IGTK ("ff:ff:ff:ff:ff:ff IGTK").
This functionality is for testing purposes and included only in builds
with CONFIG_TESTING_OPTIONS=y.
Signed-off-by: Jouni Malinen <j@w1.fi>
The new "SET sae_commit_override <hexdump>" control interface command
can be used to force wpa_supplicant to override SAE commit message
fields for testing purposes. This is included only in
CONFIG_TESTING_OPTIONS=y builds.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
When failing to trigger scan for beacon report (e.g., when the
requested duration is not supported by the driver), send a
Radio Measurement response with the mode set to refused and don't
retry the scan.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
IEEE Std 802.11-2016, 11.11.6 specifies that a station that is unable to
make a requested measurement or refuses to make a measurement shall
respond only if the measurement request was received within an
individually addressed radio measurement request frame, but shall not
respond if such a request was received in a group addressed frame.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
This allows wpa_supplicant to be configured to act as the configurator
in the case where a peer device initiates DPP Authentication.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This implements genric PKEX functionality in src/common/dpp.c and glue
code to use this in wpa_supplicant (i.e, hostapd DPP implementation does
not yet support PKEX).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Set temporary disallowed BSSID list to the driver so that the driver
doesn't try to connect to any of the blacklisted BSSIDs during
driver-based roaming operation. This commit includes support only for
the nl80211 driver interface using a QCA vendor command for this.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This adds support for DPP Configuration Protocol using GAS. Full
generation and processing of the configuration object is not included in
this commit.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add wpa_supplicant control interface commands for parsing the bootstrap
info URI from a QR Code (get peer public key) and to generate a new
bootstrap info with private key for local use. The optional
key=<hexdump> argument to the DPP_BOOTSTRAP_GEN command can be used to
specify the bootstrapping private key in OpenSSL ECPrivateKey DER
encoding format. This results in the local bootstrapping information
entry being created with the specified key instead of generating a new
random one.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
There could be multiple pending TX operations and if the earlier ones
have used wait_time, but the last one did not, the driver call for
canceling pending wait was not done. This could result in the driver
getting stuck waiting for the previously scheduled wait time and not
being able to do new operations until that. Fix this by canceling the
wait if any of the past offchannel_send_action() calls since the last
offchannel_send_action_done() used non-zero wait_time.
This was showing up as issues in certain DPP Public Action frame
sequences when the same offchannel operation is used with multiple
frames and the last frame in the sequence does not need wait_time.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Update the internal fils_completed state when offloading FILS shared key
authentication to the driver.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
In ap_scan=2 mode, wpa_supplicant_assoc_try() did not check whether the
SSID is temporarily disabled before trying to associate and this may
result in an infinite connect/disconnect loop. If the association
succeeds while the SSID is temporarily disabled, wpa_supplicant will
request to deauthenticate and that in turn will cause the SSID to be
temporarily disabled again. Fix that by postponing the association until
the SSID is no longer temporarily disabled.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
This extends the GAS/ANQP parser in wpa_supplicant to process MBO
ANQP-elements and indicate received Cellular Data Connection Preference
values over the control interface.
When a valid MBO ANQP-element is received, the following control
interface message is sent:
RX-MBO-ANQP <BSSID> cell_conn_pref=<value>
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
MBO techspec v0.0_r27 changed the MBO ANQP-element format. The MBO
element in ANQP query should now include an MBO Query List element that
contains a list of MBO elements to query.
Add API to add the MBO Query List to an ANQP query.
Format:
ANQP_GET <addr> <info_id>[,<info_id>]...[,mbo:<subtype>...]
Example for querying neighbor report with MBO cellular data
connection preference:
ANQP_GET <bssid> 272,mbo:2
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Add support for rejecting a BSS transition request using MBO reject
reason codes. A candidate is selected or rejected based on whether it is
found acceptable by both wpa_supplicant and the driver. Also accept any
candidate meeting a certain threshold if disassoc imminent is set in BTM
Request frame.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
