The local ifindex list needs to be updated only if the current bridge
interface is the correct one. If hostapd is going to move the interface
to another bridge, the old bridge ifindex must not be added. In
addition, when removing the bridge interface on deinit, it may need to
be set down to allow bridge removal.
Signed-off-by: Jouni Malinen <j@w1.fi>
The interface was incorrectly changed to station mode between the two
IBSS join requests and that made the second attempt fail. Remove that
undesired mode clearing from this special case of IBSS leave sequence.
Signed-off-by: Jouni Malinen <j@w1.fi>
Commit 9f12614b8c ('nl80211: Do not
encrypt IEEE 802.1X WEP EAPOL') tried to use
NL80211_ATTR_CONTROL_PORT_NO_ENCRYPT to disable encryption of EAPOL
frames for WEP IEEE 802.1X. However, it used incorrect key management
suite (IEEE 802.1X with WPA/WPA2 while the non-WPA version is needed
here). Consequently, the no-encrypt flag was never set to the driver
(WPA/WPA2 cases do not meet the WEP as pairwise criteria).
Signed-off-by: Jouni Malinen <j@w1.fi>
The mesh gate is used to bridge (or route) between mesh network and
another network. For example, mesh gate acts as router between mesh
network and IEEE 802.11 BSS network.
This command makes a virtual mesh interface to be used for mesh gate.
This command expects to be used like this.
wpa_cli -i wlan0 MESH_INTERFACE_ADD ifname=mesh0
wpa_cli -i mesh0 add_network
wpa_cli -i mesh0 set_network 0 ssid '"commell_2X_mmm"'
wpa_cli -i mesh0 set_network 0 mode 5
wpa_cli -i mesh0 set_network 0 frequency 2412
wpa_cli -i mesh0 set_network 0 key_mgmt SAE
wpa_cli -i mesh0 set_network 0 psk '"01234567"'
wpa_cli -i mesh0 mesh_group_add 0
wpa_cli -i wlan0 mesh_group_remove mesh0
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
This commit introduces a QCA vendor command that allows interrogation of
the vendor-specific features supported by the device/driver. Currently
the only defined feature is the ability to offload key management.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
It is possible for unmasking of 11b rates to fail if a P2P group is
terminated while the netdev is down (e.g., due to rfkill block). This
could result in the 11b TX rates being left masked for non-P2P
operations. This would be particularly unfortunate for channel 14 use
since OFDM rates are not allowed on channel 14 and only OFDM rates were
configured P2P. This issue showed up, e.g., when running hwsim test case
rfkill_autogo followed by ap_wps_conf_chan14.
It may be possible to allow the failed operation in cfg80211/mac80211,
but it looks better to work around this on wpa_supplicant side as well.
Try to unmask the 11b rates again on the next connection request if the
rate unmasking operation had failed.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This makes it easier to debug issues related to TX rate masking for P2P
use cases (and unmasking for non-P2P).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This adds verification of os_snprintf() result against the maximum
buffer length. These changes were done automatically with spatch
using the following semantic patch:
@@
expression E1,E2,E3;
statement S1;
@@
E1 = os_snprintf(E2, E3, ...);
- if (\( E1 < 0 \| E1 <= 0 \))
+ if (os_snprintf_error(E3, E1))
(
S1
|
{ ... }
)
Signed-off-by: Jouni Malinen <j@w1.fi>
This reduced number of unnecessarily duplicated driver interface
callback functions for sending Action frames by using the more generic
send_action() instead of FT specific send_ft_action().
Signed-off-by: Jouni Malinen <j@w1.fi>
This helper function had not used the nl80211_set_iface_id() helper, but
there is no reason why it couldn't re-use the same helper as other
places using nl80211_cmd_msg().
Signed-off-by: Jouni Malinen <j@w1.fi>
Use the helper function to replace places that use nlmsg_alloc(),
nl80211_cmd(), and either bss->ifindex or if_nametoindex(bss->ifname).
Signed-off-by: Jouni Malinen <j@w1.fi>
bss->wdev_id_set is set for the non-detdev P2P Device, so
nl80211_cmd_msg() can be used as-is for these cases as well.
Signed-off-by: Jouni Malinen <j@w1.fi>
This removes duplicated code for building nl80211 commands for a BSS.
This commit handles the functions that were already using
nl80211_set_iface_id().
Signed-off-by: Jouni Malinen <j@w1.fi>
This gets rid of more NLA_PUT* macro uses in nl80211 to reduce the
number of functions that depend on the hidden behavior of jumping to the
nla_put_failure label.
Signed-off-by: Jouni Malinen <j@w1.fi>
Suppose there are two APs (AP1 & AP2) and user attempted to connect to
AP2 before the previous connection with AP1 could succeed. Now, if the
connection event comes for the older AP with failed status, we should
just ignore it as the wpa_supplicant state has moved to "ASSOCIATING"
with the new AP (AP2).
This is a similar to the case where a disconnection event is ignored for
a case where local disconnect request can cause the extra event to show
up during the next association process following that command.
Signed-off-by: Jithu Jance <jithu@broadcom.com>
Using QCA vendor command, allow ACS function to be offloaded to the
driver. Once channels are selected, hostapd is notified to perform OBSS
operation.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This is needed to make following operations behave as expected since
mesh iftypes may prevent various operations (e.g., registering Probe
Request frame RX). Use same design as leave_ibss does to handle this
consistently.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
It was possible for the ignore_if_down_event flag to remain set in some
cases where interface mode change required the interface to be set down
temporarily. If that happened, the following rfkill interface down could
have been ignored and device could have been left trying to scan or
connect (which would all fail due to the interface beign down). Clean
this up by clearing the ignore_if_down_event flag on the interface down
event regardless of whether the interface is up at the time this event
is processed.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Commit 6c6678e7a4 ('nl80211: Make
br_ifindex available in i802_bss') did not cover the case where
i802_check_bridge() ends up creating the bridge interface. That left
bss->br_ifindex zero and prevented neighbor addition. Extend that
functionality to update br_ifindex once the bridge netdev has been
added.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add link measurement request to registration of Action frames to be
handled by wpa_supplicant if the driver supports TX power value
insertation.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Add Neighbor Report Response Action frame to registration of Action
frames to be handled by wpa_supplicant.
Signed-off-by: Assaf Krauss <assaf.krauss@intel.com>
Set the RRM capability flags, based on the capabilities reported
by the underlying driver.
In addition, upon connection, notify the underlying driver regarding
RRM support.
Signed-off-by: Assaf Krauss <assaf.krauss@intel.com>
cfg80211 will reject any of these attributes regardless of whether the
values actually change or not when NL80211_CMD_SET_STATION is used for
something else than TDLS. This path is hit at least when setting up
mesh, so filter out the attributes from NL80211_CMD_SET_STATION to match
the rules in cfg80211.
Signed-off-by: Jouni Malinen <j@w1.fi>
This allows adding/deleting an IPv6 neighbor entry to/from the bridge,
to which the BSS belongs. This commit adds the needed functionality in
driver_nl80211.c for the Linux bridge implementation. In theory, this
could be shared with multiple Linux driver interfaces, but for now, only
the main nl80211 interface is supported.
Signed-off-by: Kyeyoon Park <kyeyoonp@qca.qualcomm.com>
Add ops to notify about TSPECs to add/remove. Additionally, subscribe to
ADDTS/DELTS Action frames to be able to process WMM AC Action frames.
Signed-off-by: Moshe Benji <moshe.benji@intel.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Add a new option "mesh_ht_mode" that specifies the HT mode for the
mesh, with this option on, mesh beacons, actions frames, and probe
responses with include the appropriate HT information elements.
[original implementation by Chun-Yeow Yeoh <yeohchunyeow@gmail.com>]
[some fixes by Masashi Honma <masashi.honma@gmail.com>]
Signed-off-by: Ashok Nagarajan <ashok.dragon@gmail.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: Jason Mobarak <x@jason.mobarak.name>
This adds definitions for the 128-bit level Suite B AKM 00-0F-AC:11. The
functionality itself is not yet complete, i.e., this commit only
includes parts to negotiate the new AKM.
Signed-off-by: Jouni Malinen <j@w1.fi>
This allows setting a network parameter on the bridge that the BSS
belongs to.
This commit adds the needed functionality in driver_nl80211.c for the
Linux bridge implementation. In theory, this could be shared with
multiple Linux driver interfaces, but for now, only the main nl80211
interface is supported.
Signed-off-by: Kyeyoon Park <kyeyoonp@qca.qualcomm.com>
This allows setting a bridge port attribute. Specifically, the bridge
port in this context is the port to which the BSS belongs.
This commit adds the needed functionality in driver_nl80211.c for the
Linux bridge implementation. In theory, this could be shared with
multiple Linux driver interfaces, but for now, only the main nl80211
interface is supported.
Signed-off-by: Kyeyoon Park <kyeyoonp@qca.qualcomm.com>
This allows adding/deleting an IPv4 neighbor entry to/from the bridge,
to which the BSS belongs. This commit adds the needed functionality in
driver_nl80211.c for the Linux bridge implementation. In theory, this
could be shared with multiple Linux driver interfaces, but for now, only
the main nl80211 interface is supported.
Signed-off-by: Kyeyoon Park <kyeyoonp@qca.qualcomm.com>
This is an initial step in starting to split the large driver_nl80211.c
implementation into somewhat smaller parts.
Signed-off-by: Jouni Malinen <j@w1.fi>
This makes it easier to figure out from hostapd control interface
whether an interface had been added to a bridge externally at the time
hostapd interface was enabled or if the interface gets added during
hostapd operations.
Signed-off-by: Jouni Malinen <j@w1.fi>
