ap_sta_deauthenticate() does not necessarily send a Deauthentication
frame to the STA. Use ap_sta_disconnect() to drop the association so
that the notification frame goes out.
Signed-off-by: Jouni Malinen <j@w1.fi>
"user" MACACL "password" style lines in the eap_user file can now be
used to configured user entries for RADIUS-based MAC ACL.
Signed-off-by: Jouni Malinen <j@w1.fi>
This adds some helper definitions and functions to allow cfg80211 to be
tested with raw nl80211 messages built in the test scripts. The first
test case shows a case where station disassociates instead of
deauthenticates (which is the wpa_supplicant behavior).
Signed-off-by: Jouni Malinen <j@w1.fi>
These are similar to the previous cases, but with supported rate set
limited to allow the BSS membership selector to fit into that element
instead of Ext Supp Rates.
Signed-off-by: Jouni Malinen <j@w1.fi>
p2p_dev_addr was not NULL, so the all zeros case was printed as well.
Clean this up by printing p2p_dev_addr in debug prints only if it is a
real P2P Device Address.
Signed-off-by: Jouni Malinen <j@w1.fi>
The 5 GHz cases are not yet complete due to missing mac80211_hwsim
functionality. The current test cases allow the ACS operation to fail
for those cases.
Signed-off-by: Jouni Malinen <j@w1.fi>
If a separate P2P group interface is used, PBC overlap during group
formation causes the group interface to be removed, which ends up with
the interface context becoming invalid. Fix this by scheduling a timeout
to process the PBC overlap and interface removal instead of removing the
interface directly before the connection operation has returned.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
This was forgotten from the per-network ocsp parameter addition. The new
parameter needs to be stored to the configuration file similarly to the
other EAP parameters.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
If a new connection is attempted while there is a pending sme-connection
radio work, cancel the pending radio work and continue with the new
connection attempt. This is preferable over rejecting the new work and
continuing with the pending one, as it is possible that the previous
work is no longer valid.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
According to the standard, if the max A-MPDU VHT cap is <= 3, we
have to adjust the max A-MPDU HT cap to the same value. Otherwise
it should be set to 3.
Take care of it when the max VHT A-MPDU value is overridden.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Add support of vendor command to hostapd ctrl_iface.
Vendor command's format:
VENDOR <vendor id> <sub command id> [<hex formatted data>]
The 3rd argument will be converted to binary data and then passed as
argument to the sub command.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
When primary and secondary channel were switched and config was
reloaded, secondary channel was incorrectly overwritten.
Proceed as for other settings that should not be changed and don't
allow to overwrite.
Signed-off-by: Pawel Kulakowski <pawel.kulakowski@tieto.com>
While framing the TDLS Setup Confirmation frame, the driver needs to
know if the TDLS peer is VHT/HT/WMM capable and thus shall construct the
VHT/HT operation / WMM parameter elements accordingly. Supplicant
determines if the TDLS peer is VHT/HT/WMM capable based on the presence
of the respective IEs in the received TDLS Setup Response frame.
The host driver should not need to parse the received TDLS Response
frame and thus, should be able to rely on the supplicant to indicate
the capability of the peer through additional flags while transmitting
the TDLS Setup Confirmation frame through tdls_mgmt operations.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
When hostapd choose to reuse an existing interface, it does not add it
to the set of interfaces from which we accept EAPOL packets.
Make sure we always add it to that set.
Signed-off-by: Maxime Bizon <mbizon@freebox.fr>
This adds a pointer to hostapd.conf to using 'iw list' with the current
nl80211 drivers to determine supported interface combinations.
Signed-off-by: Jouni Malinen <j@w1.fi>
This allows a single ANQP query to be used to fetch both IEEE 802.11
defined ANQP elements and Hotspot 2.0 vendor specific elements.
ANQP_GET <addr> <info id>[,<info id>]...
[,hs20:<subtype>][...,hs20:<subtype>]
For example:
ANQP_GET 00:11:22:33:44:55:66 258,268,hs20:3,hs20:4
Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
This allows drivers that build the WPA/RSN IEs internally to use similar
design for building the OSEN IE.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
There is not much point in building devices with WPS 1.0 only supported
nowadays. As such, there is not sufficient justification for maintaining
extra complexity for the CONFIG_WPS2 build option either. Remove this by
enabling WSC 2.0 support unconditionally.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Use P2P group formation timeout to wait for the 4-way handshake to
complete on a persistent reinvocation on a P2P Client.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
