There is no need to keep temporary keys in memory beyond the end of the
association, so explicitly clear any SAE buffers that can contain keys
as soon as such keys are not needed.
Signed-off-by: Jouni Malinen <j@w1.fi>
It was possible for auth/assoc timeout/failure event from the driver to
result in unexpected processing during mesh group setup if that
operation was started before the previously started driver operation to
association/connect had completed. Since those events cannot happen in
mesh cases, ignore them to avoid issues due to this corner case.
For example, monitor_iface_unknown_sta followed by wpas_mesh_secure test
case resulted in failure without this change.
Signed-off-by: Jouni Malinen <j@w1.fi>
Send link measurement response when a request is received. Advertise
only RCPI, computing it from the RSSI of the request. The TX power field
is left to be filled by the driver. All other fields are not published.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Add the ability to send a Neighbor Report Request (part of
RRM). Requester is then notified once the report arrives.
Signed-off-by: Assaf Krauss <assaf.krauss@intel.com>
In case the AP we are associating with advertises support for RRM,
advertise our own RRM support in the (Re)Association Request frame. This
is done by adding an RRM Capabilities IE. The underlying driver is
expected to further add a Power Capabilities IE to the request, and set
the Radio Measurement flag in the Capability Info field. At this point
the RRM Capabilities IE advertises no measurement support.
Signed-off-by: Assaf Krauss <assaf.krauss@intel.com>
If the last scans are recent (for now, less than ten seconds old), use
them instead of triggering a new scan when a BSS Transition Management
Request frame is received. As a fallback, allow a new scan to be
triggered if no matches were found.
Signed-off-by: Jouni Malinen <j@w1.fi>
Add the TSPEC to the driver on successful TSPEC ADDTS response. Delete
the TSPEC when receiving DELTS action.
Signed-off-by: Moshe Benji <moshe.benji@intel.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Initialize WMM AC data structures upon successful association
with an AP that publishes WMM support, and deinitialize the data
structure when the association is no longer valid.
Signed-off-by: Moshe Benji <moshe.benji@intel.com>
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Modify network mode to support mode number 5 when CONFIG_MESH is
enabled.
Signed-off-by: Javier Lopez <jlopex@gmail.com>
Signed-off-by: Jason Mobarak <x@jason.mobarak.name>
Signed-off-by: Thomas Pedersen <thomas@noack.us>
The mesh peering manager establishes and maintains links among
mesh peers, tracking each peer link via a finite state machine.
This implementation supports open mesh peerings.
[assorted fixes from Yu Niiro <yu.niiro@gmail.com>]
[more fixes from Masashi Honma <masashi.honma@gmail.com>]
Signed-off-by: Javier Lopez <jlopex@gmail.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: Ashok Nagarajan <ashok.dragon@gmail.com>
Signed-off-by: Jason Mobarak <x@jason.mobarak.name>
Signed-hostap: Bob Copeland <me@bobcopeland.com>
Add routines to (de)initialize mesh interface data structures and
join and leave mesh networks.
Signed-off-by: Javier Lopez <jlopex@gmail.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: Jason Mobarak <x@jason.mobarak.name>
Signed-off-by: Thomas Pedersen <thomas@noack.us>
This commit introduces a QCA vendor command and event to provide an
option to use extended versions of the nl80211 connect/roam operations
in a way that allows drivers to offload key management operations to the
driver/firmware.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
If "STA_AUTOCONNECT 0" has been used to disable automatic connection on
disconnection event and the driver indicates multiple disconnection
events for the disconnection from the current AP when WPS is started, it
could have been possible to hit a case where wpa_s->disconnected was set
to 1 during WPS processing and the following scan result processing
would stop the operation.
wpa_s->key_mgmt == WPA_KEY_MGMT_WPS check was trying to avoid to skip
autoconnect when WPS was in use, but that does not seem to work anymore.
Fix this by checking through wpas_wps_searching() as well to avoid
setting wpa_s->disconnect = 1 when there is an ongoing WPS operation.
Signed-off-by: Jouni Malinen <j@w1.fi>
The commit 5cd4740580 has rearranged the
update scan results code and hence the IEs were not getting updated
properly for ap_scan=1 case. This can result in a 4-way handshake
failure in the roaming case (IE mismatch in 3/4 EAPOL). Fix this by
updating the scan results even if ap_scan=1 is used and network does not
need to get reselected based on association information.
Signed-off-by: Jithu Jance <jithu@broadcom.com>
Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
Signed-off-by: Jouni Malinen <j@w1.fi>
Incorrect field was used to determine the init=<value> in the regulatory
domain changed control interface event.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
There is no need to trigger new SA Query procedure to check the state of
the connection immediately after having performed such a check. Limit
the impact of burst of unprotected Deauth/Disassoc frames by starting a
new SA Query procedure only once at least 10 seconds has passed from the
previous SA Query that was triggered by reception of an unprotected
disconnection. The first SA Query procedure for each association does
not follow this rule to avoid issues with test cases that expect to see
an SA Query every time.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
If a link is unreachable, the specification mandates we should send a
teardown packet via the AP with a specific teardown reason. Force this
by first disabling the link and only then sending the teardown packet
for the LOW_ACK event.
Rename the TDLS LOW_ACK event handler to better reflect its purpose.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
This removes number of unnecessary #ifdef CONFIG_P2P blocks from generic
code by hiding the conditional build into p2p_supplicant.h with empty
inline functions.
Signed-off-by: Jouni Malinen <j@w1.fi>
This avoids an incorrect ARRAY_VS_SINGLETON report for a case where a
pointer is taken to the specified field in a frame and not to a single
octet. Bounds checking was already handled separately.
Signed-off-by: Jouni Malinen <j@w1.fi>
wpa_supplicant_event() is required to include the event data for AP mode
events. In theory, a non-AP mode event could be sent here from the
driver wrapper, so reject such event.
Signed-off-by: Jouni Malinen <j@w1.fi>
This is mainly to keep static analyzers silent since it does not look
like this code path can be reached in practice due to the way
association events are handled and current_ssid is either set before
resched here or the association is rejected. Anyway, if this could be
reached, the wpa_supplicant_set_wpa_none_key() call would end up
dereferencing a NULL pointer, so add an explicit check to make sure that
does not happen.
Signed-off-by: Jouni Malinen <j@w1.fi>
This adds [DMG] and [PBSS] flags for scan results and BSS table entries
using the IEEE Std 802.11ad-2012 updated definition of the Capability
field.
Signed-off-by: Boris Sorochkin <qca_bsoroc@qca.qualcomm.com>
The radio works for the interface get removed if interface is disabled.
This could have left P2P module in invalid state if the interface got
disabled during a p2p_find or p2p_listen operation. Clear the state in
such a case to avoid blocking following operations due to P2P module
assuming it is still in progress of doing something.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
No need to call ibss_rsn_deinit() again since it is already being called
by wpa_supplicant_mark_disassoc().
Signed-off-by: Eduardo Abinader <eduardo.abinader@openbossa.org>
It is possible for the disconnection event from the driver to not get
delivered when interface is disabled. To maintain consistent ctrl_iface
event behavior, indicate CTRL-EVENT-DISCONNECTED in such a case if we
were in connected state.
Signed-off-by: Jouni Malinen <j@w1.fi>
This allows external programs to monitor driver signal change events
through wpa_supplicant when bgscan is used.
Signed-off-by: Jouni Malinen <j@w1.fi>
When an ANQP fetch is triggered and ANQP_3GPP_CELLULAR_NETWORK info is
required, initialize scard to be ready when comparing ANQP and
credentials.
Signed-off-by: Jean Trivelly <jean.trivelly@intel.com>
If a separate P2P group interface is used, PBC overlap during group
formation causes the group interface to be removed, which ends up with
the interface context becoming invalid. Fix this by scheduling a timeout
to process the PBC overlap and interface removal instead of removing the
interface directly before the connection operation has returned.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Scan for GO on the negotiated operating channel for few iterations
before searching on all the supported channels during persistent group
reinvocation. In addition, use the already known SSID of the group in
the scans. These optimizations reduce group formation time.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
When a sched_scan_stopped event is received and there is a pending PNO,
it used regular scheduled scan parameters instead of PNO specific
parameters. Change it by calling wpas_start_pno().
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
This enables more convenient protocol testing of AP and P2P
functionality in various error cases and unexpected sequences without
having to implement each test scenario within wpa_supplicant.
ext_mgmt_frame_handle parameter can be set to 1 to move all management
frame processing into an external program through control interface
events (MGMT-RX and MGMT-TX-STATUS) and command (MGMT_TX). This is
similar to the test interface that was added to hostapd previously, but
allows more control on offchannel operations and more direct integration
with the internal P2P module.
Signed-off-by: Jouni Malinen <j@w1.fi>
Commit 3d910ef497 tried to make
last-network selection behave more consistently with Interworking
network selection preferences. However, it did not take into account
that other network block may have higher priority. In such cases, the
last added network from Interworking network selection should actually
not be selected for the next connection. Fix this by limiting the
last-network preference to work only within a priority class.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Previously, it would have been possible for the network to be marked
disabled and that marking to be ignored if a recoverable disconnection
reason event were processed. Avoid this by verifying network status
before trying to reconenct back to the same BSS.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Previously, any network block could be used to select the BSS to connect
to when processing scan results after Interworking network selection.
This can result in somewhat unexpected network selection in cases where
credential preferences indicated that a specific network was selected,
but another network ended up getting used for the connection. While the
older networks continue to be valid, add special processing for this
initial post-interworking-connect case to get more consistent network
selection to match with the Interworking network selection result.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
While testing rfkill blocking of a scanning interface, it
was seen that the ongoing scan never completes. This happens
since EVENT_SCAN_RESULTS is discarded on a disabled interface.
Fix this and also other possible radio work completion issues
by removing all the radio works (including started) of the
disabled interface.
To be able to remove already started radio works, make their
callbacks be reentrant with deinit flag (when the work
is started), so each radio work should be able to handle
its own termination.
Signed-hostap: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
wpa_s->current_bss was updated too late for the
wpa_supplicant_rsn_supp_set_config() call within
wpa_supplicant_select_config(). Re-order code so that current_bss gets
updated between current_ssid update and this call to set the WPA state
machine configuration, so that the new code that determines whether the
current GO support the new IP address assignment mechanism works.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This adds a QCA vendor specific nl80211 event to allow the driver to
indicate a list of frequency ranges that should be avoided due to
interference or possible known co-existance constraints. Such
frequencies are marked as not allowed for P2P use to force groups to be
formed on different channels.
If a P2P GO is operating on a channel that the driver recommended not to
use, a notification about this is sent on the control interface and
upper layer code may decide to tear down the group and optionally
restart it on another channel. As a TODO item, this could also be changed
to use CSA to avoid removing the group.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
When GAS is used with PMF negotiated, Protected Dual of Public Action
frames are expected to be used instead of Public Action frames, i.e.,
the GAS/ANQP frames are expected to be encrypted. Conver Public Action
GAS queries to use Dual of Public Action frame if PMF has been
negotiated with the AP to which the frame is being sent.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
