Commit d8d940b746 introduced a regression
that prevented TSN APs from being used with WEP since the AP was
rejected if it advertised WPA or RSN IE when we were configured to use
WEP. Resolve this by checking whether the AP is advertising a TSN, i.e.,
whether the AP allows WEP to be used as a group cipher. If so, allow
the AP to be selected if we are configured to use static WEP or
IEEE 802.1X (non-WPA).
It should be noted that this is still somewhat more restricted in AP
selection than earlier wpa_supplicant branches (0.7.x or older) that
ignore the WPA/RSN IE completely when configured for non-WPA.
Add a new driver event, EVENT_INTERFACE_UNAVAILABLE, for indicating
that the driver is not able to continue operating the virtual
interface in its current mode anymore, e.g., due to operating
channel for GO interface forced to a DFS channel by another virtual
interface.
When this happens for a P2P group interface, the P2P group will
be terminated and P2P-GROUP-REMOVED event shows the reason for
this as follows:
P2P-GROUP-REMOVED wlan0 GO reason=UNAVAILABLE
The driver wrapper may indicate EVENT_CHANNEL_LIST_CHANGED before
completing init(). This would likely result in segfault when driver
channel list is being read as part of processing this event when
P2P is enabled.
The workaround to ignore no ctrl::ack received for GO Negotiation
Confirmation frame was only supposed to be used when the frame was
actually transmitted and just the ack was not received. However, due
to the way the driver failure on transmitting the frame were reported,
this ended up getting applied for all failures in sending the GO
Negotiation Confirmation frame.
Improve this by providing a mechanism to indicate whether send_action
operations fail locally before the frame was actually transmitted or
because of not receiving ack frame after having transmitted the frame.
Previously, wpa_supplicant remaining in scanning state without
trying to connect, but there is no particular need to do that.
Instead, cancel WPS operation completely whenever PBC session
overlap is detected.
Disconnection event may be received while in associating state.
Previously, wpa_supplicant could get stuck not trying to reconnect
in that case at least with nl80211. Allow scan request in this
state to avoid the issue. This helps especially with APs that do
load balancing by sending Deauthentication frame as a response to
Reassociation Request frame after successful Authentication frame
exchange.
ctrl_interface STA_AUTOCONNECT command can now be used to disable
automatic reconnection on receiving disconnection event. The default
behavior is for wpa_supplicant to try to reconnect automatically, i.e.,
to maintain previous behavior.
The overlap condition cannot disappear before group formation timeout
hits, so there is no point in continuing in this case and failure can
be indicated immediately.
If CONFIG_WPS_STRICT is set, validate WPS IE(s) in management frames and
reject the frames if any of the mandatory attributes is missing or if an
included attribute uses an invalid value. In addition, verify that all
mandatory attributes are included and have valid values in the WSC
messages.
Verify that the driver wrapper is using a valid deauth/disassoc
event before dereferencing the addr pointer. The address is required
to be set in AP mode, but it is safer to verify this here than to
trust on all driver wrappers doing the correct thing.
Commit d8d940b746 broke the logic on
iterating through all configured network blocks. This was supposed
to continue the loop on mismatch to allow other than the first
configured network to be found.
This removes quite a bit of duplicated code and allows network block
priority configuration to be used to prefer unprotected networks and
also allows use on open network with good signal strength even if
scan results show a protected network with marginal signal strength
that does not allow it to be used.
This is needed to avoid trying to reassociate based on new scan
results when using wpa_supplicant to control AP mode. This could
happen if something external triggered the driver to run a scan.
It is possible that l2_packet is not used with wpa_supplicant
in some cases, so better make sure we do not end up notifying
l2_packet code about authentications unless it was actually
initialized in the first place.
Add a new wpa_supplicant state: interface disabled. This can be used
to allow wpa_supplicant to be running with the network interface even
when the driver does not actually allow any radio operations (e.g.,
due to rfkill).
Allow driver_nl80211.c and driver_wext.c to start while rfkill is in
blocked state (i.e., when ifconfig up fails) and process rfkill
events to block/unblock WLAN.
This adds more details into the CTRL-EVENT-DISCONNECTED event to
make it easier to figure out which network was disconnected in some
race conditions and to what could have been the reason for
disconnection. The reason code is currently only available with
the nl80211 driver wrapper.
'wpa_cli roam <bssid>' can now be used to test roaming within an ESS
(e.g., for FT over-the-air). This command will bypass a new scan and
will select the BSS based on the specified BSSID. It is responsibility
of the caller to make sure that the target AP is in the BSS table.
This can be done, e.g., by running a scan before the roam command,
if needed.
Instead of parsing the IEs in the callers, use the already existing
parser in wpa_ft.c to handle MDIE and FTIE from initial MD association
response. In addition, this provides more complete access to association
response IEs to FT code which will be needed to fix FT 4-way handshake
message 2/4.
This allows bgscan modules to use more information to decide on when
to perform background scans. bgscan_simple can now change between
short and long background scan intervals based on signal strength
and in addition, it can trigger immediate scans when the signal
strength is detected to be dropping.
bgscan_simple takes following parameters now:
short interval:signal strength threshold:long interval
For example:
bgscan="simple:30:-45:300"
This can be used to limit which frequencies are considered when
selecting a BSS. This is somewhat similar to scan_freq, but will
also affect any scan results regardless of which program triggered
the scan.
Previously, this was only done with userspace MLME (i.e., driver_test.c);
now, driver_nl80211.c can deliver the FT Action Response (FT-over-DS)
for processing. The reassociation after successful FT Action frame
exchange is not yet implemented.
This is needed to allow the BSS table entry for the previously used
BSS to be removed. Now wpa_bss_in_use() can return 0 for the last BSS
that was used as soon as deauthentication/disassociation event has been
received.
When multiple APs are present in scan results with similar signal
strength, wpa_supplicant may end up bounching between them frequently
whenever new scan results are available (e.g., due to periodic scans
requested by NetworkManager). This can result in unnecessary roaming
and in case of the current cfg80211 version, to frequent network
disconnections.
Do not request a roam if the current BSS is still present in the scan
results and the selected BSS is in the same ESS and has only a slighly
stronger signal strength.
The three existing enums were already depending on using the same
values in couple of places and it is just simpler to standardize on
one of these to avoid need for mapping between different enums for
the exact same thing.
This fits better in wpa_supplicant/scan.c. Couple of remaining
scan_helpers.c functions are currently used in driver wrappers,
but they can likely be removed in the future.
