WEP should not be used for anything anymore. As a step towards removing
it completely, move all WEP related functionality to be within
CONFIG_WEP blocks. This will be included in builds only if CONFIG_WEP=y
is explicitly set in build configuration.
Signed-off-by: Jouni Malinen <j@w1.fi>
There was a bug in wmediumd in that it didn't set the
frequency of frames, and thus they were always received
by mac80211_hwsim, regardless of channel it was on.
Add two tests that verify we only find a single instance
of an AP if we only have that one, and run this both with
and without wmediumd.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Test case sequence "persistent_group_channel scan_bss_expiration_count"
was failing with UML when using time travel. This seemed to be because
there was no explicit wait to confirm that the AP has been fully
disabled before running the next scan. Work around this by verifying
that hostapd has terminated the BSS and waiting a bit after that before
proceeding.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
scan_dfs fails with this message.
---------------
wlan0: Country code not reset back to 00: is US
wlan0: Country code cleared back to 00
---------------
This patch fixes the issue.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
cfg80211 was modified to allow the Multiple BSSID Index element to be
included in the IEs for a nontransmitted BSS. Update the validation step
in this test case to allow that different with the IEs in the Beacon
frame (transmitted BSS).
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The first scan for the unknown BSSID could have been timed in a manner
that allows passive scanning to find the real AP even if that AP's
beacon interval was 1000 (e.g., heavy CPU load changed timing so that
the AP beaconing started at suitable time). The check for BSS result
entry not including Probe Response frame was comparing incorrect BSS
entries (bss2 vs. bss1) which resulted in the test case claiming failure
even when there was no unexpected Probe Response frame.
Fix this by comparing the beacon_ie and ie parameters from the same BSS
entry (bss1).
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This is needed to avoid leaving unexpected cfg80211 regulatory country
code in place at the point when a test case terminates.
Signed-off-by: Jouni Malinen <j@w1.fi>
This adds some minimal testing for Multi-BSS connection attempts. The
part for nontransmitted BSS is limited since hostapd/mac80211 does not
yet have sufficient support for Multi-BSS in AP mode.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
If wpa_state is left to SCANNING by a previously executed test case,
scan_trigger_failure will fail. Instead of waiting for that failure,
check for wpa_state at the beginning of the test case and report a more
helpful error message if the test case would fail due to a previously
executed test case.
Signed-off-by: Jouni Malinen <j@w1.fi>
After successfully passing the 525 tests on a remote setup mark the
tests as remote compatible.
Signed-off-by: Jonathan Afek <jonathanx.afek@intel.com>
The hwsim tests used to execute shell commands in the tests using the
subprocess python module. Use the cmd_execute() general function for
executing "iw scan .." so that this would also work on remote setups.
Signed-off-by: Jonathan Afek <jonathanx.afek@intel.com>
Pass the full apdev to the add_ap() function instead of just ifname.
This allows us to handle also remote hosts while we can check
apdev['hostname'], apdev['port'].
This step (1) converts the cases where apdev[#]['ifname'] was used as
the argument to hostapd.add_ap().
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
These test caases depended on a single active scan round finding the AP.
It is possible for the Probe Response frame to get delayed sufficiently
to miss the response especially when testing under heavy load with
multiple parallel VMs. Allow couple of scan retries to avoid reporting
failures from these test cases.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This makes the test log more readable by converting the values to
integers and sorting the array.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This verifies the nl80211 behavior to abort a scan on an explicit
control interface request and on connection request.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The test sequence "scan_and_bss_entry_removed ap_wps_ap_scan_2" resulted
in failure due to an old BSS entry remaining from the first test case to
the second and the WPS_PBC operation on a forced BSSID ending up picking
the incorrect BSS entry. Make this more robust by clearing the scan
results from cfg80211.
Signed-off-by: Jouni Malinen <j@w1.fi>
run-tests.py is running as root, so sudo does not need to be used
anymore from within each test case.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
