Define the following additional TWT operations:
QCA_WLAN_TWT_GET_STATS, QCA_WLAN_TWT_CLEAR_STATS,
QCA_WLAN_TWT_GET_CAPABILITIES, QCA_WLAN_TWT_SETUP_READY_NOTIFY.
Also define new attributes to qca_wlan_vendor_attr_twt_setup
and qca_wlan_vendor_attr_twt_nudge.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Replace the implicit boolean checks that used int variables with use of
a more explicit bool variable type.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Support possible band combinations of 2.4 GHz, 5 GHz, and 6 GHz with
QCA_WLAN_VENDOR_ATTR_SETBAND_MASK attribute. Ensure backwards
compatibility with old drivers that are using
QCA_WLAN_VENDOR_ATTR_SETBAND_VALUE attribute and supporting only 2.4 GHz
and 5 GHz bands.
Signed-off-by: Veerendranath Jakkam <vjakkam@codeaurora.org>
The function name for adding frequency lists changed, so this test case
needs a matching change to avoid failures.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This functionality was repeated for couple of times. Use a shared helper
function to avoid code duplication.
Signed-off-by: Veerendranath Jakkam <vjakkam@codeaurora.org>
The earlier workaround for UBSAN issues in commit 3b6b3ae581 ("Modify
dl_list_for_each() to not use unaligned access with WPA_TRACE") ended up
using a construction in which the type cast to the containing structure
was compared instead of the struct dl_list pointers. While that worked
around the UBSAN issue, it resulted in a comparison that gcc-10
interprets as being out of bounds for struct dl_list (which it obviously
is since this is to find the start of the containing structure).
Revert that workaround and instead, mark the struct dl_list used within
struct os_alloc_trace to have matching 16 octet alignment as the
containing structure. This is also restoring consistent design for
dl_list_for_each*().
Signed-off-by: Jouni Malinen <j@w1.fi>
This was broken in the kernel in mac80211 for a while, until commit
780a8c9efc65 ("mac80211: do not disable HE if HT is missing on 2.4 GHz")
fixed it.
Add a test for wifi generation on 2.4 GHz in addition to the 5 GHz one.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When the driver sends a CQM RSSI threshold event, wpa_supplicant queries
the driver for the signal and noise values. However, it is possible that
by that time the station has already disconnected from the AP, so these
values are no longer valid. In this case, indicate that these values are
invalid by setting them to WPA_INVALID_NOISE.
Previously a value of 0 would be reported, which may be confusing as
this is a valid value.
Since nl80211_get_link_signal() and nl80211_get_link_noise() already set
invalid values for a case of failure, just use the value set by these
functions even if they fail.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Allow to run local/remote process like:
- ubus listen
- logread -f
- tail -f
- wpa_cli
- hostapd_cli
And next wait for specific event(s).
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@gmail.com>
S1G beacons save a few bytes by not requiring the RSNE in beacon if RSN
BSS is configured. Handle this in wlantest by only clearing RSNE from
the BSS info if frame is a Probe Response frame.
Signed-off-by: Thomas Pedersen <thomas@adapt-ip.com>
Sweden now allows channel 149 in the updated wireless-regdb. Choose
Japan for the negative test instead.
Signed-off-by: Thomas Pedersen <thomas@adapt-ip.com>
Add a new hostapd configuration parameters rssi_ignore_probe_request to
ignore Probe Request frames received with too low RSSI.
Signed-off-by: John Crispin <john@phrozen.org>
Add initial_freq_list to wpa_supplicant configuration. This option
allows wpa_supplicant to scan a smaller list of frequencies when it
starts. This in turn allows for a faster connection to an already known
network. This limit applies only for the initial scan operation and does
not restrict other channels from being used in consecutive scans.
Tests have shown this to reduce the amount of time for connecting to a
network from roughly 3 seconds to roughly 0.1 second.
Signed-off-by: Frederik Juul <frederik.juul@3shape.com>
Previously hostapd would not stop transmitting when a DFS event was
detected and no available channel to switch to was available.
Disable and re-enable the interface to enter DFS state. This way, TX
does not happen until the kernel notifies hostapd about the NOP
expiring.
Signed-off-by: David Bauer <mail@david-bauer.net>
Add the ability to disable HT/VHT/HE for specific BSS from hostapd.conf.
- Add disable_11ax boolean to hostapd_bss_config.
- Change disable_11n and disable_11ac to bool in hostapd_bss_config.
- Add configuration option to set these disable_11* parameters
(which were previously used only automatically based on incompatible
security parameters to disable HT/VHT).
Signed-off-by: Shay Bar <shay.bar@celeno.com>
Add a test which uses a DFS channel, waits for CAC afterwards successful
mesh join and then triggers a radar event and checks if the mesh comes
up again on the same device.
Signed-off-by: Markus Theil <markus.theil@tu-ilmenau.de>
The hostapd DFS code deinitializes and initializes the AP interface, if
a clean channel switch is not possible. In this case the AP code paths
would deinit the driver, for example nl80211, without wpa_supplicant
code paths getting notice of this.
Therefore add callbacks for wpa_supplicant mesh methods, which are
called on init/deinit of the AP BSS. These callbacks are then used to
handle the reset in the mesh code.
Signed-off-by: Markus Theil <markus.theil@tu-ilmenau.de>
Send mesh group started notification after join completion
callback is called.
Implement outstanding TODO, to leave the mesh network on deinit.
Signed-off-by: Markus Theil <markus.theil@tu-ilmenau.de>
Only change freq params, if ifmsh->freq is set initially, which only
happens if hostapd_get_hw_features in setup_interface2 succeeds.
Signed-off-by: Markus Theil <markus.theil@tu-ilmenau.de>
