libnl has a bug, when binding more than two sockets and releasing one,
it will release the wrong address and then try to reuse it, which fails.
Therefore, we need to reimplement the socket address assignment logic
locally for libnl 1.1.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
wpa_supplicant showed signal levels incorrectly with some drivers:
Jun 6 16:29:36 rupert wpa_supplicant[18945]: Current BSS: 00:0d:97:11:40:d6
level=190
Jun 6 16:29:36 rupert wpa_supplicant[18945]: Selected BSS: 00:0d:97:11:50:09
level=192
Judging from output from other tools (iwlist) and the min_diff block
at the end of wpa_supplicant_need_to_roam, it seems these values
should actually be negative. Specifically, if one treats that number
as a signed char instead of unsigned, everything matches up.
To be honest, I've little to no understanding of wireless, but looking
at the source code for wireless-tools (iw_print_stats in iwlib.c), it
seems that the fields of the iw_quality struct need to be decoded
differently depending on various flags. I guess
src/drivers/driver_wext.c should have similar logic in
wext_get_scan_qual.
I wrote a patch that attempts to replicate some of that logic,
although it may be more complicated than is necessary; I think some of
the complexity is for backwards-compatibility, which might not be
necessary depending on wpa_supplicant's dependencies? In any case, it
is attached. Again, I don't know how any of this works, so it's likely
the patch is a bit off. But I think at least the logic to determine
min_diff in wpa_supplicant_need_to_roam would be more accurate if
level were determined correctly.
WPS 2.0 mandates the AP to include WPS IE in (Re)Association Response
if the matching (Re)Association Request included WPS IE. Provide the
needed WPS IE information to the driver_ops API for drivers that
process association frames internally.
Note: This modifies the driver_ops API by adding a new argument to
set_ap_wps_ie().
This is needed to be able to change parameters for dynamically
created interfaces between the creation of the interface and
association/start AP commands.
Following ctrl_interface commands can now be used:
P2P_SET client_apsd disable
- disable configuration (i.e., use driver default) in client mode
P2P_SET client_apsd <BE>,<BK>,<VI>,<VO>;<max SP Length>
- enable UASPD with specific trigger configuration (0/1) per AC
(max SP Length is currently ignored)
P2P_SET go_apsd disable
- disable configuration (i.e., use driver default) in AP mode
P2P_SET go_apsd <0/1>
- disable/enable APSD in AP mode
Some NDIS drivers require a workaround to allow them to associate
with a WPS AP that is already using protection (Privacy field = 1).
Let driver_ndis.c know if the AP is already using Privacy and if so,
configure a dummy WEP key to force the driver to associate.
This patch adds support for wired IEEE 802.1X client on the Solaris.
I have tested with these:
OS : OpenSolaris 2009.06
EAP : EAP-MD5
Switch : Cisco Catalyst 2950
When passing several authentication algorithms through auth_alg, we
should try all of them when the first one fails. The wext driver goes
through the connect nl80211 command and the retries are then handled by
the kernel. The nl80211 doesn't and we have to handle that from
userspace.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
DEAUTH messages can come from a number of different sources. The one
that's hurting us currently is DEAUTH netlink messages coming to us
from compat-wireless in response to local_state_change DEAUTH messages
we sent as a part of cleaning up state in driver_nl80211's
clear_state_mismatch() function. However, DEAUTH messages can come
from a variety of unwanted sources, including directed denial-of-service
attacks (although MAC verification doesn't place that high a barrier),
so this validation is actually generically useful, I think.
The downside to this method is that without a kernel based approach
"iw dev wlan0 link" no longer works correctly after clear_state_mismatch()
is done. This will be pursued with the kernel folks.
cfg80211/mac80211 seems to be unwilling to change interface mode in
some cases. Make these less likely to cause problems by trying the
changes up to 10 times with 100 msec intervals.
Replace use of rfkill block event with rtnetlink ifdown. This makes
the design more robust since the rfkill event could have been for
another interface while the rtnetlink events are already filtered
based of ifindex. In addition, the new design handles other than
rfkill-triggered ifdown/ifup events, too. rfkill unblocked event
is still needed to try to set the interface back up. If the unblock
was for another interface, ifup will fail and the driver state is
not changed.
Setting IEEE80211_PARAM_AUTHMODE to IEEE80211_AUTH_AUTO ends up enabling
Privacy mode in the driver. We need to clear that to allow hostapd to be
reconfigured into open mode.
Previous version driver_bsd.c switches the channel in
wpa_driver_bsd_associate(). This patch changes it to use set_freq().
I have tested this patch on FreeBSD 8.0/NetBSD 5.0.2 with hostapd,
wpa_supplicant(AP) and wpa_supplicant(STA).
Add a new wpa_supplicant state: interface disabled. This can be used
to allow wpa_supplicant to be running with the network interface even
when the driver does not actually allow any radio operations (e.g.,
due to rfkill).
Allow driver_nl80211.c and driver_wext.c to start while rfkill is in
blocked state (i.e., when ifconfig up fails) and process rfkill
events to block/unblock WLAN.
There are no subdirectories in any of these directories or plans
for adding ones. As such, there is no point in running the loop
that does not do anything and can cause problems with some shells.
This adds more details into the CTRL-EVENT-DISCONNECTED event to
make it easier to figure out which network was disconnected in some
race conditions and to what could have been the reason for
disconnection. The reason code is currently only available with
the nl80211 driver wrapper.
There is no absolute requirement for separating address allocation
into separate functions, so simplify the driver wrapper interface
to use just if_add and if_remove instead of adding the new
alloc_interface_addr() and release_interface_addr() functions.
if_add() can now indicate if the driver forced a different interface
name or address on the virtual interface.
This removes transmission of some unnecessary Deauthentication
frames in cases where we only need to clear the local state. In
addition, this resolves issues for 802.11r FT-over-DS by allowing
authentication state to be set locally even when no actual
Authentication frame is to be transmitted.
This can be used to test 802.11w by sending a protected or unprotected
deauth/disassoc frame.
hostapd_cli deauth <dst addr> test=<0/1>
hostapd_cli disassoc <dst addr> test=<0/1>
test=0: unprotected
test=1: protected
On NetBSD 5.0.2, wpa_supplicant build results in messages below.
../src/drivers/driver_bsd.c: In function 'wpa_driver_bsd_get_ssid':
../src/drivers/driver_bsd.c:876: warning: passing argument 2 of 'bsd_get_ssid'
from incompatible pointer type
../src/drivers/driver_bsd.c:876: warning: passing argument 3 of 'bsd_get_ssid'
makes integer from pointer without a cast
../src/drivers/driver_bsd.c:876: error: too many arguments to function
'bsd_get_ssid'
../src/drivers/driver_bsd.c: In function 'wpa_driver_bsd_scan':
../src/drivers/driver_bsd.c:1125: warning: passing argument 2 of 'bsd_set_ssid'
from incompatible pointer type
../src/drivers/driver_bsd.c:1125: warning: passing argument 3 of 'bsd_set_ssid'
makes integer from pointer without a cast
../src/drivers/driver_bsd.c:1125: error: too many arguments to function
'bsd_set_ssid'
gmake: *** [../src/drivers/driver_bsd.o] Error 1
This patch solves this issue.
This is a step in adding FT support with nl80211-based drivers.
driver_nl80211.c is now registering to handle the FT Action frames
and is able to transmit FT Request frame. Received FT Action frames
are not yet indicated as driver events.
This patch allows the nl80211 driver to create its own per-bss context
and pass it to the drv_priv pointer of the hostapd bss state.
With this and the following patch, stations can associate to and switch
between multiple BSS interfaces of a single wiphy.
This obsoletes a few instances of passing ifname to a callback, those
can be removed in a separate patch.
It might also be useful to move more fields from the driver data to the
per-bss data structure in the future.
This patch allows wpa_supplicant to compile on Debian's kfreebsd
architectures.
Patch by Stefan Lippers-Hollmann based on work done by Petr Salinger
and Emmanuel Bouthenot for 0.6.X (http://bugs.debian.org/480572).
filter_ssids=1 global configuration parameter can now be used to
enable scan result filtering (with -Dnl80211 only for now) based on
the configured SSIDs. In other words, only the scan results that have
an SSID matching with one of the configured networks are included in the
BSS table. This can be used to reduce memory needs in environments that
have huge number of APs.
wpa_supplicant can now be notified of suspend/resume events, e.g.,
from pm-action scripts. This allows wpa_supplicant to clear information
that may become invalid during a suspend operation.
The kernel side support for this was just added into
wireless-testing.git. This commit adds the driver wrapper code needed
to allow wpa_supplicant to use the new functionality.
Some drivers may need to use a specific ifname for the virtual
interface, so allow them to do this with a new parameter passed
to the alloc_interface_addr() handler.
This patch aggregates ioctls.
First is SIOCS80211. The SIOCS80211's arguments has 3 couples.
1-1. i_len, i_data
1-2. i_val
1-3. i_len, i_data, i_val (currently only IEEE80211_IOC_APPIE)
There were 3 routines for each cases. This patch aggregates these to
one.
Second is SIOCG80211. The SIOCG80211 returns 2 type of value.
2-1. i_len
2-2. i_val
There were 2 routines for each cases. This patch aggregates these to
one.
I have tested on both FreeBSD 8.0 and NetBSD 5.0.1 with these cases.
[hostapd]
RSN-PSK(CCMP)/WPA-PSK(TKIP)
[wpa_supplicant(STA)]
RSN-PSK(CCMP)/WPA-PSK(TKIP)
[wpa_supplicant(AP)]
RSN-PSK(CCMP)/WPA-PSK(TKIP)
This patch enables FreeBSD channel control.
I have tested on FreeBSD 7.2 with these cases.
[hostapd]
RSN-PSK(CCMP)/WPA-PSK(TKIP)
[wpa_supplicant(STA)]
RSN-PSK(CCMP)/WPA-PSK(TKIP)
[wpa_supplicant(AP)]
RSN-PSK(CCMP)/WPA-PSK(TKIP)
The attached patch unifies hostapd wpa_driver_bsd_ops and
wpa_supplicant wpa_driver_bsd_ops.
I have tested on NetBSD 5.0.1 with these cases.
[hostapd]
RSN-PSK(CCMP)/WPA-PSK(TKIP)
[wpa_supplicant(STA)]
RSN-PSK(CCMP)/WPA-PSK(TKIP)
[wpa_supplicant(AP)]
RSN-PSK(CCMP)/WPA-PSK(TKIP)
This patch modifies field name of struct bsd_driver_data to use
same name of struct wpa_driver_bsd_data. This is a preparation of
unifying struct bsd_driver_data and struct wpa_driver_bsd_data.
The bsd_send_eapol() adds Ethernet header by itself. This patch changes it
to use l2_packet functionality.
I have tested on NetBSD 5.0.1 with WPA-PSK(TKIP).
