Record all generated per-client PSKs in the persistent group network
block and configure these for the GO Authenticator whenever re-starting
the persistent group. This completes per-client PSK support for
persistent groups.
Signed-hostap: Jouni Malinen <j@w1.fi>
Even after listen duration is over, P2P module remained in
P2P_LISTEN_ONLY state, which is blocking station mode scans. Fix this by
stopping P2P listen explicitly to update p2p_state to IDLE when listen
duration expires.
Signed-hostap: Syed Asifful Dayyan <syedd@broadcom.com>
By default, P2P is initialized for all driver interfaces and this makes
P2P getting initialized for non-P2P station interface if the supplicant
is started first on this interface. If an interface is dedicated for
non-P2P station mode, it is now possible to disable P2P initialization
by adding 'p2p_disabled=1' in the configuration file of non-P2P station
interface, irrespective of the order in which supplicant is started.
Signed-hostap: Sreenath Sharma <sreenats@broadcom.com>
Previously, concurrent station mode scans were postponed during an
ongoing P2P group formation up to the point of completed WPS
provisioning step. This would allow a scan to be started before the P2P
client has completed association for the data connection if a scan
request were timed to hit the window between the provisioning step and
the following association. Avoid this by extending P2P-in-progress state
to continue until the first data connection has been completed as part
of group formation. Use a ten second timeout for this to avoid leaving
scans disabled indefinitely if the client fails to connect completely.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This provides status information about the negotiated group to
wpa_supplicant control interface monitors during group formation in a
form that is easier to use than having to fetch the information
separately.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
When 'p2p_group_remove *' is called while the station interface
is connected, the flow also disconnects the station interface.
Fix this by skipping non-P2P interfaces in the iteration.
Signed-hostap: Ilan Peer <ilan.peer@intel.com>
This reverts commit ce970851af.
It turned out that this breaks lots of use cases where p2p_find is
issued while already in p2p_listen state. As such, we cannot reject
p2p_find this easily without checking for more specific cases.
Signed-hostap: Jouni Malinen <j@w1.fi>
Though p2p_find is not expected during ongoing P2P connection, it is
possible that any third party application issues a p2p_find resulting in
connection failure. Address this by rejecting any p2p_find command while
connection is in progress.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Change the P2P flows to use the number of concurrent channels
supported by the device and the number of currently used channels
for the P2P flows.
Signed-hostap: Ilan Peer <ilan.peer@intel.com>
Signed-hostap: David Spinadel <david.spinadel@intel.com>
There is no need to wait for the 15 second group formation timeout
before indicating P2P group formation failure if GO mode cannot be
started successfully for some reason.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Adding a new wpa_supplicant control interface for the dedicated
P2P_DEVICE would be quite confusing for programs that manage P2P
operations. Remove this control interface and require the global control
interface to be used since it will provide consistent interface for both
the new dedicated P2P_DEVICE (non-netdev) and old style P2P management
through a netdev.
Signed-hostap: Jouni Malinen <j@w1.fi>
The interface name for the P2P group interface is derived from the
P2P management interface. When the P2P management interface is a
P2P Device interface, i.e., p2p-dev-wlanX, the name for the group
interface is abbreviated to p2p-X (X being group index). When the
P2P management interface starts with p2p-dev- use its postfix
instead. So P2P management interface p2p-dev-wlan3 results in group
interface name p2p-wlan3-0.
Signed-hostap: Arend van Spriel <arend@broadcom.com>
If the capability flag of the driver indicates a dedicated P2P Device is
supported, a P2P Device interface is created.
Create the P2P Device in main interface creation loop when the added
interface flags support and P2P supplicant is not yet initialized
avoiding recursion of add_interface.
Do not register l2_packet for P2P Device interface (both for EAPOL and
for TDLS).
Signed-hostap: Arend van Spriel <arend@broadcom.com>
Setting p2p_no_group_iface means 'use P2P management interface as P2P
connection interface' because it attempts to change the interface type.
The P2P_DEVICE is a dedicated interface and can not be changed. As such
ignore the configuration option.
Signed-hostap: Arend van Spriel <arend@broadcom.com>
If the driver wrapper supports best operation channel indication, the
p2p_group_add command can now use special values (freq=2 and freq=5) to
indicate that the re-invoked persistent GO is to be started on the
specified band.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
When STA interface is connected and P2P interface gets invited in a
different channel from previous P2P group, the invitiation would fail
because of no common channel found. Fix this by using different logic
when device support multi channel concurrency.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This removes the "IFNAME=<ifname> " prefix from P2P events that are
received through the global control interface since these events are not
really specific to any network interface, but the full device.
Signed-hostap: Jouni Malinen <j@w1.fi>
Replace direct wpa_msg() calls with p2p_dbg(), p2p_info(), and p2p_err()
calls that use a new debug_print() callback to handle actual debug
printing outside the P2P module.
Signed-hostap: Jouni Malinen <j@w1.fi>
This removes wpa_ctrl.h dependency from src/p2p/* and makes the P2P
events more consistent, i.e., everything that is aimed for upper layer
processing from the wpa_supplicant control interfaces is generated in
p2p_supplicant.c.
Signed-hostap: Jouni Malinen <j@w1.fi>
Commit 21d996f775 added p2p_pref_chan as a
configuration file parameter, but included only the case of dynamically
setting this at runtime through the control interface SET command.
Complete this functionality by taking this value into use directly from
the configuration file, too.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This can be used to configure wpa_supplicant to ignore old scan results
from the driver cache in cases where such results were not updated after
the scan trigger from wpa_supplicant. This can be useful in some cases
where the driver may cache information for a significant time and the AP
configuration is changing. Many such cases are for testing scripts, but
this could potentially be useful for some WPS use cases, too.
Signed-hostap: Jouni Malinen <j@w1.fi>
If the AP (P2P GO) has changes its channel of SSID recently, the BSS
table may have multiple entries for a BSSID. Select the one which was
most recently updated for WPS/P2P operations in such case to increase
the likelihood of using current information.
Signed-hostap: Jouni Malinen <j@w1.fi>
sta_scan_pending was supposed to be accurate enough for determining
whether a P2P scan needs to be postponed. However, it has turned out
that there were cases where sta_scan_pending was not cleared properly.
While the known cases have now been addressed, it is possible that some
other cases may still exist. To avoid issues with P2P operationg getting
stuck, verify more carefully that there is a real pending station mode
scan (either in progress or scheduled to be requested).
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Make the implementation more consistent and cleaner by using a single
function for addressing all the cases where completion of a station mode
scan operation allows a P2P operation (search) to be re-started.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
If a peer replies to persistent group invitation with status code 8
(unknown group), remove the peer from the p2p_client_list if we are the
GO or remove the persistent group if we are the P2P client since it
looks like that the peer has dropped persistent group credentials and
the provisioning step needs to be executed again.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
p2p_ignore_shared_freq=1 in the configuration file (or "SET
p2p_ignore_shared_freq 1" on control interface) can now be used to
configure wpa_supplicant to ignore the preference on shared operating
channel when the driver support multi-channel concurrency. The default
behavior is to try to start any new P2P group on an operating channel
that is already in use on another virtual interface to avoid extra cost
from hopping between multiple channels. If this new parameter is set to
1, such preference is not used and instead, the channel for the new P2P
group is selected based on other preferences while ignoring operating
channels of any concurrent connection.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Commit 50285f5ca8 changed number of rules
in channel selection and among other things, it broke the design where
the currently used operating channel on a virtual interface that is
shared by the same radio is preferred to avoid costs related to
multi-channel concurrency. Fix this regression by making the P2P module
aware of the shared channel and using that preference as the highest
priority when re-selecting the channel during negotiation.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Commit 79879f4ae8 enabled all channels to
be used when negotiating channel with a driver that supports
multi-channel concurrency. Extend that to cover cases where the channel
is not being negotiated (e.g., p2p_group_add to start a GO).
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Commit 77dfafd07d cancels group formation
timeout on group removal case but failed to reset the
p2p_in_provisioning flag. This can lead to repeated p2p_find failures if
the group gets removed before completion of the WPS provisioning step
(e.g., GO tears down the group). Fix this by clearing
p2p_pin_provisioning when cancelling group formation.
Signed-hostap: Vivek Natarajan <nataraja@qca.qualcomm.com>
When p2p_invite persistent=<id> is used to request a persistent group to
be re-invoked, the peer may reply with status=1 (info not yet available)
if upper layer processing of the invitiation is requested. The peer is
ten expected to start another invitation exchanged within 120 seconds if
the user authorizes the connection. Allow this process to be used more
easily by automatically authorizing the peer that we tried to invite to
use this second invitation sequence even if persistent_reconnect=0.
For this mechanism to work, the device that starts the invitation needs
to start listen mode to be able to receive the invitation request from
the peer. At least for now, this is not done automatically, but future
changes could potentially enable this automatically at least if there
are no concurrent operations in progress.
Example sequence on the initiator:
cmd: P2P_INVITE persistent=1 peer=<addr>
event: P2P-INVITATION-RESULT status=1
cmd: P2P_LISTEN 120
wait for peer to start another invitiation round.. group will be
re-invoked automatically
On the peer (with persistent_reconnect=0):
event: P2P-INVITATION-RECEIVED sa=<addr> persistent=1 [freq=<MHz>]
wait for user approval
cmd: P2P_INVITE persistent=1 peer=<addr>
group will be re-invoked automatically
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
When a device that is a GO in a persistent group receives an Invitation
Request from a P2P client and persistent_reconnect=0, upper layer is
notified of this with P2P-INVITATION-RECEIVED event. The upper layer is
supposed to run another invitation exchange is this case, but if that
does not happen and the GO is started without successful (status=0)
invitation exchange, the operating channel for the group may end up
getting set in a way that the P2P client is not able to support. Provide
optional freq parameter in the P2P-INVITATION-RECEIVED event on the GO
side. If this parameter is received and the upper layer decides to issue
P2P_GROUP_ADD command, that command should include this freq parameter
to make sure the operating channel gets selected from the set that the
peer can support.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Peer device includes its list of allowed operating channels in the
Invitation Response frame. When we are becoming the GO, use that list
from the peer to filter out acceptable channels to avoid selecting a
channel that the peer is unable to use.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
When re-invoking a persistent group in P2P client role, the new
pref=<MHz> parameter can now be used with the p2p_invite command to
indicate a preferred operating frequency. Unlike the older freq=<MHz>
parameter, this leaves GO an option to select another channel (from our
supported channels) if the GO cannot accept the channel.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
p2p_connect() and p2p_invite() cases used more or less identical
implementatin. Use a shared function to avoid duplicated code.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
If multi channel concurrency is supported, we have to populate the
p2p_channels with list of channels that we support. Use the same design
that was previously added for GO Negotiation.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
For various P2P use cases, it is useful to have more accurate timestamp
for the peer information update. This commit improves scan result
handling by using a single timestamp that is taken immediately after
fetching the results from the driver and then using that value to
calculate the time when the driver last updated the BSS entry. In
addition, more debug information is added for P2P peer updates to be
able to clearly see how old information is being used here.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Previously, only some P2P states were considered to postpone concurrent
station mode scans during group formation. Especially the WPS
provisioning step was skipped due to issues to scans run on the P2P
client interface (see commit fc6997b345).
This is not ideal since a concurrent scan can slow down group formation
considerably and potentially make it time out. Enforce p2p-in-progress
through all steps of group formation on another interface to address
this.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Group formation timeout is normally canceled when 4-way handshake is
completed (WPA_COMPLETED -> wpas_p2p_completed). However, it is possible
for the GO to stop the group before this happens (i.e., send
Deauthentication frame with reason code 3 before 4-way handshake is
completed). This resulted in the group getting removed, but the group
formation timeout left behind. The unexpected timeout may then result in
undesired termination of the following operation. Fix this by canceling
the group formation timeout in wpas_p2p_group_delete() similarly to how
group idle timeout was canceled there.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
These channels were already enabled for P2P use, but the local
configuration parameter was not allowed to use the operating class in
which the 40 MHz channels are specified.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Commit 50178335bf introduced a regression
for P2P-GROUP-STARTED event indication during p2p_connect-join when
using a separate P2P group interface. wpa_s->global->p2p_group_formation
was already set in that case to point to the group interface and this
commit changed this to point to incorrect interface. Fix this by setting
p2p_group_formation here only in case a separate group interface is not
used.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Commit bb4d4deb4b introduced a code path
that could potentially end up calling wpa_config_update_psk() with NULL
passphrase. While that may not happen in practice, it is better to make
sure it doesn't happen since that function will dereference the
passphrase pointer unconditionally.
Signed-hostap: Jouni Malinen <j@w1.fi>
This continues optimizations for use of CPU heavy pbkdf2_sha1() in GO
setup after the earlier commit 30c371e8a5
by allowing PSK to be used instead of passphrase when creating
persistent group information manually for the GO.
It should be noted that this would not meet the requirements in the P2P
specification (GO shall maintain the passphrase), so this should be used
only when there is no need to allow manual configuration of legacy STAs
using the passphrase.
Signed-hostap: Masashi Honma <masashi.honma@gmail.com>
cfg80211 caches the scan results according the channel number. Due to
the 15 sec aging this might cause the user mode to see more than one
scan result with the same BSSID, e.g. - one scan result for the
P2P Device and one for the P2P GO (once it's enabled).
Fix this by updating the device entry only if the new peer entry is
newer than the one previously stored.
Signed-off-by: Yoni Divinsky <yoni.divinsky@ti.com>
Signed-off-by: Victor Goldenshtein <victorg@ti.com>
Signed-off-by: Igal Chernobelsky <igalc@ti.com>
Signed-hostap: Arik Nemtsov <arik@wizery.com>
There is no need for p2p_supplicant.c to access wpa_s->pending_action_tx
so move these references to offchannel.c to get a bit cleaner interface
between the components.
Signed-hostap: Jouni Malinen <j@w1.fi>
p2p_cancel did not properly cancel a pending p2p_connect-join operation.
Address the different steps in that process: initial scan, Provision
Discovery exchange before connection, and WPS provisioning step
(including the scans before WPS).
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The PD Request retry limit can be used to achieve the same behavior,
so drop this duplicated timeout mechanism and control the timeout
based on MAX_PROV_DISC_REQ_RETRIES.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
